Software License Agreement (BSD License)
- Copyright (c) 2010, microBuilder SARL
+ Copyright (c) 2012, microBuilder SARL
All rights reserved.
Redistribution and use in source and binary forms, with or without
MCP4725 0xC0 1100000x
TSL2561 0x72 0111001x
TCS3414 0x72 0111001x
+ PN532 0x48 0100100x
[1] Alternative addresses may exists, but the addresses listed in this
table are the values used in the code base
/*=========================================================================
FIRMWARE VERSION SETTINGS
-----------------------------------------------------------------------*/
- #define CFG_FIRMWARE_VERSION_MAJOR (0)
- #define CFG_FIRMWARE_VERSION_MINOR (9)
- #define CFG_FIRMWARE_VERSION_REVISION (8)
+ #define CFG_FIRMWARE_VERSION_MAJOR (1)
+ #define CFG_FIRMWARE_VERSION_MINOR (0)
+ #define CFG_FIRMWARE_VERSION_REVISION (0)
/*=========================================================================*/
/*=========================================================================*/
+/*=========================================================================
+ GPIO INTERRUPTS
+ -----------------------------------------------------------------------
+
+ IF you wish to use the GPIO interrupt handlers elsewhere in your code,
+ you should probably define a seperate IRQHandler for the appropriate
+ GPIO bank rather than using the definitions in core/gpio/gpio.c (to
+ avoid causing problems in other projects, and to make updates easier,
+ etc.) To disable the default IRQHandler, simply comment out the
+ define below for the appropriate GPIO bank and implement the handler
+ somewhere else.
+
+ GPIO_ENABLE_IRQ0 If defined, PIOINT0_IRQHandler will be declared and
+ handled in core/gpio/gpio.c
+ GPIO_ENABLE_IRQ1 If defined, PIOINT1_IRQHandler will be declared and
+ handled in core/gpio/gpio.c
+ GPIO_ENABLE_IRQ2 If defined, PIOINT2_IRQHandler will be declared and
+ handled in core/gpio/gpio.c
+ GPIO_ENABLE_IRQ3 If defined, PIOINT3_IRQHandler will be declared and
+ handled in core/gpio/gpio.c
+
+ -----------------------------------------------------------------------*/
+ #ifdef CFG_BRD_LPC1343_REFDESIGN
+ // #define GPIO_ENABLE_IRQ0
+ #define GPIO_ENABLE_IRQ1
+ // #define GPIO_ENABLE_IRQ2
+ // #define GPIO_ENABLE_IRQ3
+ #endif
+
+ #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
+ // #define GPIO_ENABLE_IRQ0
+ #define GPIO_ENABLE_IRQ1
+ // #define GPIO_ENABLE_IRQ2
+ // #define GPIO_ENABLE_IRQ3
+ #endif
+
+ #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
+ // #define GPIO_ENABLE_IRQ0
+ #define GPIO_ENABLE_IRQ1
+ // #define GPIO_ENABLE_IRQ2
+ // #define GPIO_ENABLE_IRQ3
+ #endif
+
+ #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
+ // #define GPIO_ENABLE_IRQ0
+ #define GPIO_ENABLE_IRQ1
+ // #define GPIO_ENABLE_IRQ2
+ // #define GPIO_ENABLE_IRQ3
+ #endif
+
+ #ifdef CFG_BRD_LPC1343_802154USBSTICK
+ // #define GPIO_ENABLE_IRQ0
+ #define GPIO_ENABLE_IRQ1
+ // #define GPIO_ENABLE_IRQ2
+ // #define GPIO_ENABLE_IRQ3
+ #endif
+
+ #ifdef CFG_BRD_LPC1343_OLIMEX_P
+ // #define GPIO_ENABLE_IRQ0
+ #define GPIO_ENABLE_IRQ1
+ // #define GPIO_ENABLE_IRQ2
+ // #define GPIO_ENABLE_IRQ3
+ #endif
+/*=========================================================================*/
+
+
/*=========================================================================
ALTERNATE RESET PIN
-----------------------------------------------------------------------
/*=========================================================================*/
+/*=========================================================================
+ ADC
+ -----------------------------------------------------------------------
+
+ ADC_AVERAGING_ENABLE To get better results, the ADC code can take
+ a number of samples and return the average
+ value. This is slower, but can give more
+ accurate results compared to single-reading.
+
+ To enable averaging, set ADC_AVERAGING_ENABLE
+ to a non-zero value.
+ ADC_AVERAGING_SAMPLES The number of ADC samples to read and
+ average if ADC averaging is enabled.
+
+ -----------------------------------------------------------------------*/
+ #ifdef CFG_BRD_LPC1343_REFDESIGN
+ #define ADC_AVERAGING_ENABLE (1)
+ #define ADC_AVERAGING_SAMPLES (5)
+ #endif
+
+ #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
+ #define ADC_AVERAGING_ENABLE (1)
+ #define ADC_AVERAGING_SAMPLES (5)
+ #endif
+
+ #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
+ #define ADC_AVERAGING_ENABLE (0)
+ #define ADC_AVERAGING_SAMPLES (5)
+ #endif
+
+ #ifdef CFG_BRD_LPC1343_802154USBSTICK
+ #define ADC_AVERAGING_ENABLE (0)
+ #define ADC_AVERAGING_SAMPLES (5)
+ #endif
+
+ #ifdef CFG_BRD_LPC1343_OLIMEX_P
+ #define ADC_AVERAGING_ENABLE (0)
+ #define ADC_AVERAGING_SAMPLES (5)
+ #endif
+/*=========================================================================*/
+
+
/*=========================================================================
ON-BOARD LED
-----------------------------------------------------------------------
PRINTF REDIRECTION
-----------------------------------------------------------------------
+ CFG_PRINTF_MAXSTRINGSIZE Maximum size of string buffer for printf
CFG_PRINTF_UART Will cause all printf statements to be
redirected to UART
CFG_PRINTF_USBCDC Will cause all printf statements to be
output will be ignored.
-----------------------------------------------------------------------*/
#ifdef CFG_BRD_LPC1343_REFDESIGN
+ #define CFG_PRINTF_MAXSTRINGSIZE (255)
// #define CFG_PRINTF_UART
#define CFG_PRINTF_USBCDC
#define CFG_PRINTF_NEWLINE "\r\n"
#endif
#ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
+ #define CFG_PRINTF_MAXSTRINGSIZE (255)
#define CFG_PRINTF_UART
// #define CFG_PRINTF_USBCDC
#define CFG_PRINTF_NEWLINE "\r\n"
#endif
#ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
+ #define CFG_PRINTF_MAXSTRINGSIZE (255)
// #define CFG_PRINTF_UART
#define CFG_PRINTF_USBCDC
#define CFG_PRINTF_NEWLINE "\r\n"
#endif
#ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
+ #define CFG_PRINTF_MAXSTRINGSIZE (255)
#define CFG_PRINTF_UART
// #define CFG_PRINTF_USBCDC
#define CFG_PRINTF_NEWLINE "\n"
#endif
#ifdef CFG_BRD_LPC1343_802154USBSTICK
+ #define CFG_PRINTF_MAXSTRINGSIZE (255)
// #define CFG_PRINTF_UART
#define CFG_PRINTF_USBCDC
#define CFG_PRINTF_NEWLINE "\r\n"
#endif
#ifdef CFG_BRD_LPC1343_OLIMEX_P
+ #define CFG_PRINTF_MAXSTRINGSIZE (255)
// #define CFG_PRINTF_UART
#define CFG_PRINTF_USBCDC
#define CFG_PRINTF_NEWLINE "\r\n"
a pre-determined LCD screen to be included
during build. Only one LCD driver can be
included during the build process (for ex.
- 'drivers/lcd/hw/ILI9325.c')
+ 'drivers/displays/hw/ILI9325.c')
CFG_TFTLCD_INCLUDESMALLFONTS If set to 1, smallfont support will be
included for 3x6, 5x8, 7x8 and 8x8 fonts.
This should only be enabled if these small
#if CFG_CHIBI_PROMISCUOUS != 0 && CFG_CHIBI_PROMISCUOUS != 1
#error "CFG_CHIBI_PROMISCUOUS must be equal to either 1 or 0"
#endif
+ #if !defined GPIO_ENABLE_IRQ1
+ #error "GPIO_ENABLE_IRQ1 must be enabled when using Chibi (Chibi IRQ is on GPIO1.8)"
+ #endif
#endif
#ifdef CFG_TFTLCD
#endif
#endif
+#if ADC_AVERAGING_ENABLE && ADC_AVERAGING_SAMPLES < 1
+ #error "ADC_AVERAGING_SAMPLES must be 1 or higher when ADC averaging is enabled"
+#endif
+
#endif
projects / hackover2013-badge-firmware.git / blobdiff