X-Git-Url: http://git.rohieb.name/hackover2013-badge-firmware.git/blobdiff_plain/d21a664a23190d6747fb1080de5de5bd6277534e..7aeb2288ae07778b92b3c9224cbc149cb08282a8:/projectconfig.h

diff --git a/projectconfig.h b/projectconfig.h
index 62026c2..ad7ad82 100644
--- a/projectconfig.h
+++ b/projectconfig.h
@@ -7,7 +7,7 @@
 
     Software License Agreement (BSD License)
 
-    Copyright (c) 2010, microBuilder SARL
+    Copyright (c) 2012, microBuilder SARL
     All rights reserved.
 
     Redistribution and use in source and binary forms, with or without
@@ -187,7 +187,7 @@
     MCP4725                     0xC0      1100000x
     TSL2561                     0x72      0111001x
     TCS3414                     0x72      0111001x
-	PN532                       0x48      0100100x
+    PN532                       0x48      0100100x
 
     [1]  Alternative addresses may exists, but the addresses listed in this
          table are the values used in the code base
@@ -198,9 +198,9 @@
 /*=========================================================================
     FIRMWARE VERSION SETTINGS
     -----------------------------------------------------------------------*/
-    #define CFG_FIRMWARE_VERSION_MAJOR            (0)
-    #define CFG_FIRMWARE_VERSION_MINOR            (9)
-    #define CFG_FIRMWARE_VERSION_REVISION         (8)
+    #define CFG_FIRMWARE_VERSION_MAJOR            (1)
+    #define CFG_FIRMWARE_VERSION_MINOR            (0)
+    #define CFG_FIRMWARE_VERSION_REVISION         (0)
 /*=========================================================================*/
 
 
@@ -230,6 +230,72 @@
 /*=========================================================================*/
 
 
+/*=========================================================================
+    GPIO INTERRUPTS
+    -----------------------------------------------------------------------
+
+    IF you wish to use the GPIO interrupt handlers elsewhere in your code,
+    you should probably define a seperate IRQHandler for the appropriate
+    GPIO bank rather than using the definitions in core/gpio/gpio.c (to
+    avoid causing problems in other projects, and to make updates easier,
+    etc.)  To disable the default IRQHandler, simply comment out the
+    define below for the appropriate GPIO bank and implement the handler
+    somewhere else.
+
+    GPIO_ENABLE_IRQ0    If defined, PIOINT0_IRQHandler will be declared and
+                        handled in core/gpio/gpio.c
+    GPIO_ENABLE_IRQ1    If defined, PIOINT1_IRQHandler will be declared and
+                        handled in core/gpio/gpio.c
+    GPIO_ENABLE_IRQ2    If defined, PIOINT2_IRQHandler will be declared and
+                        handled in core/gpio/gpio.c
+    GPIO_ENABLE_IRQ3    If defined, PIOINT3_IRQHandler will be declared and
+                        handled in core/gpio/gpio.c
+
+    -----------------------------------------------------------------------*/
+    #ifdef CFG_BRD_LPC1343_REFDESIGN
+      // #define GPIO_ENABLE_IRQ0
+      #define GPIO_ENABLE_IRQ1
+      // #define GPIO_ENABLE_IRQ2
+      // #define GPIO_ENABLE_IRQ3
+    #endif
+
+    #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
+      // #define GPIO_ENABLE_IRQ0
+      #define GPIO_ENABLE_IRQ1
+      // #define GPIO_ENABLE_IRQ2
+      // #define GPIO_ENABLE_IRQ3
+    #endif
+
+    #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
+      // #define GPIO_ENABLE_IRQ0
+      #define GPIO_ENABLE_IRQ1
+      // #define GPIO_ENABLE_IRQ2
+      // #define GPIO_ENABLE_IRQ3
+    #endif
+
+    #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
+      // #define GPIO_ENABLE_IRQ0
+      #define GPIO_ENABLE_IRQ1
+      // #define GPIO_ENABLE_IRQ2
+      // #define GPIO_ENABLE_IRQ3
+    #endif
+
+    #ifdef CFG_BRD_LPC1343_802154USBSTICK
+      // #define GPIO_ENABLE_IRQ0
+      #define GPIO_ENABLE_IRQ1
+      // #define GPIO_ENABLE_IRQ2
+      // #define GPIO_ENABLE_IRQ3
+    #endif
+	
+    #ifdef CFG_BRD_LPC1343_OLIMEX_P
+      // #define GPIO_ENABLE_IRQ0
+      #define GPIO_ENABLE_IRQ1
+      // #define GPIO_ENABLE_IRQ2
+      // #define GPIO_ENABLE_IRQ3
+    #endif
+/*=========================================================================*/
+
+
 /*=========================================================================
     ALTERNATE RESET PIN
     -----------------------------------------------------------------------
@@ -337,9 +403,9 @@
     ADC_AVERAGING_ENABLE      To get better results, the ADC code can take
                               a number of samples and return the average
                               value.  This is slower, but can give more
-                              accurate results caused of single-reading
-                              peaks and dips.
-                              To enable average, set ADC_AVERAGING_ENABLE
+                              accurate results compared to single-reading.
+                              
+                              To enable averaging, set ADC_AVERAGING_ENABLE
                               to a non-zero value.
     ADC_AVERAGING_SAMPLES     The number of ADC samples to read and
                               average if ADC averaging is enabled.
@@ -962,7 +1028,7 @@
                                 a pre-determined LCD screen to be included
                                 during build.  Only one LCD driver can be 
                                 included during the build process (for ex.
-                                'drivers/lcd/hw/ILI9325.c')
+                                'drivers/displays/hw/ILI9325.c')
     CFG_TFTLCD_INCLUDESMALLFONTS If set to 1, smallfont support will be
                                 included for 3x6, 5x8, 7x8 and 8x8 fonts.
                                 This should only be enabled if these small
@@ -1132,6 +1198,9 @@
   #if CFG_CHIBI_PROMISCUOUS != 0 && CFG_CHIBI_PROMISCUOUS != 1
     #error "CFG_CHIBI_PROMISCUOUS must be equal to either 1 or 0"
   #endif
+  #if !defined GPIO_ENABLE_IRQ1
+    #error "GPIO_ENABLE_IRQ1 must be enabled when using Chibi (Chibi IRQ is on GPIO1.8)"
+  #endif
 #endif
 
 #ifdef CFG_TFTLCD