#include <linux/pkt_sched.h>
#include <linux/compile.h>
#include <linux/mii.h>
+#include <linux/phy.h>
#include <linux/ethtool.h>
#include <linux/ctype.h>
#include <linux/platform_device.h>
#define CRC_LEN 4
#define RX_OFFSET 2
-#define AR2313_BUFSIZE (AR2313_MTU + ETH_HLEN + CRC_LEN + RX_OFFSET)
+#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE)
+#define VLAN_HDR 4
+#else
+#define VLAN_HDR 0
+#endif
+
+#define AR2313_BUFSIZE (AR2313_MTU + VLAN_HDR + ETH_HLEN + CRC_LEN + RX_OFFSET)
#ifdef MODULE
MODULE_LICENSE("GPL");
#define virt_to_phys(x) ((u32)(x) & 0x1fffffff)
// prototypes
-static short armiiread(struct net_device *dev, short phy, short reg);
-static void armiiwrite(struct net_device *dev, short phy, short reg,
- short data);
#ifdef TX_TIMEOUT
static void ar2313_tx_timeout(struct net_device *dev);
#endif
static void ar2313_halt(struct net_device *dev);
static void rx_tasklet_func(unsigned long data);
+static void rx_tasklet_cleanup(struct net_device *dev);
static void ar2313_multicast_list(struct net_device *dev);
+static int mdiobus_read(struct mii_bus *bus, int phy_addr, int regnum);
+static int mdiobus_write(struct mii_bus *bus, int phy_addr, int regnum, u16 value);
+static int mdiobus_reset(struct mii_bus *bus);
+static int mdiobus_probe (struct net_device *dev);
+static void ar2313_adjust_link(struct net_device *dev);
+
#ifndef ERR
#define ERR(fmt, args...) printk("%s: " fmt, __func__, ##args)
#endif
dev->dev_addr[0], dev->dev_addr[1], dev->dev_addr[2],
dev->dev_addr[3], dev->dev_addr[4], dev->dev_addr[5], dev->irq);
- /* start link poll timer */
- ar2313_setup_timer(dev);
-
+ sp->mii_bus.priv = dev;
+ sp->mii_bus.read = mdiobus_read;
+ sp->mii_bus.write = mdiobus_write;
+ sp->mii_bus.reset = mdiobus_reset;
+ sp->mii_bus.name = "ar2313_eth_mii";
+ sp->mii_bus.id = 0;
+ sp->mii_bus.irq = kmalloc(sizeof(int), GFP_KERNEL);
+ *sp->mii_bus.irq = PHY_POLL;
+
+ mdiobus_register(&sp->mii_bus);
+
+ if (mdiobus_probe(dev) != 0) {
+ printk(KERN_ERR "ar2313: mdiobus_probe failed");
+ rx_tasklet_cleanup(dev);
+ ar2313_init_cleanup(dev);
+ unregister_netdev(dev);
+ kfree(dev);
+ } else {
+ /* start link poll timer */
+ ar2313_setup_timer(dev);
+ }
+
return 0;
}
struct ar2313_private *sp = dev->priv;
u16 phyData;
- phyData = armiiread(dev, sp->phy, MII_BMSR);
+ phyData = mdiobus_read(&sp->mii_bus, sp->phy, MII_BMSR);
if (sp->phyData != phyData) {
if (phyData & BMSR_LSTATUS) {
/* link is present, ready link partner ability to deterine
u16 reg;
sp->link = 1;
- reg = armiiread(dev, sp->phy, MII_BMCR);
+ reg = mdiobus_read(&sp->mii_bus, sp->phy, MII_BMCR);
if (reg & BMCR_ANENABLE) {
/* auto neg enabled */
- reg = armiiread(dev, sp->phy, MII_LPA);
+ reg = mdiobus_read(&sp->mii_bus, sp->phy, MII_LPA);
duplex = (reg & (LPA_100FULL | LPA_10FULL)) ? 1 : 0;
} else {
/* no auto neg, just read duplex config */
return 0;
}
-static int netdev_get_ecmd(struct net_device *dev,
- struct ethtool_cmd *ecmd)
-{
- struct ar2313_private *np = dev->priv;
- u32 tmp;
-
- ecmd->supported =
- (SUPPORTED_10baseT_Half | SUPPORTED_10baseT_Full |
- SUPPORTED_100baseT_Half | SUPPORTED_100baseT_Full |
- SUPPORTED_Autoneg | SUPPORTED_TP | SUPPORTED_MII);
-
- ecmd->port = PORT_TP;
- /* only supports internal transceiver */
- ecmd->transceiver = XCVR_INTERNAL;
- /* not sure what this is for */
- ecmd->phy_address = 1;
-
- ecmd->advertising = ADVERTISED_MII;
- tmp = armiiread(dev, np->phy, MII_ADVERTISE);
- if (tmp & ADVERTISE_10HALF)
- ecmd->advertising |= ADVERTISED_10baseT_Half;
- if (tmp & ADVERTISE_10FULL)
- ecmd->advertising |= ADVERTISED_10baseT_Full;
- if (tmp & ADVERTISE_100HALF)
- ecmd->advertising |= ADVERTISED_100baseT_Half;
- if (tmp & ADVERTISE_100FULL)
- ecmd->advertising |= ADVERTISED_100baseT_Full;
-
- tmp = armiiread(dev, np->phy, MII_BMCR);
- if (tmp & BMCR_ANENABLE) {
- ecmd->advertising |= ADVERTISED_Autoneg;
- ecmd->autoneg = AUTONEG_ENABLE;
- } else {
- ecmd->autoneg = AUTONEG_DISABLE;
- }
-
- if (ecmd->autoneg == AUTONEG_ENABLE) {
- tmp = armiiread(dev, np->phy, MII_LPA);
- if (tmp & (LPA_100FULL | LPA_10FULL)) {
- ecmd->duplex = DUPLEX_FULL;
- } else {
- ecmd->duplex = DUPLEX_HALF;
- }
- if (tmp & (LPA_100FULL | LPA_100HALF)) {
- ecmd->speed = SPEED_100;
- } else {
- ecmd->speed = SPEED_10;
- }
- } else {
- if (tmp & BMCR_FULLDPLX) {
- ecmd->duplex = DUPLEX_FULL;
- } else {
- ecmd->duplex = DUPLEX_HALF;
- }
- if (tmp & BMCR_SPEED100) {
- ecmd->speed = SPEED_100;
- } else {
- ecmd->speed = SPEED_10;
- }
- }
-
- /* ignore maxtxpkt, maxrxpkt for now */
-
- return 0;
-}
-
-static int netdev_set_ecmd(struct net_device *dev,
- struct ethtool_cmd *ecmd)
-{
- struct ar2313_private *np = dev->priv;
- u32 tmp;
-
- if (ecmd->speed != SPEED_10 && ecmd->speed != SPEED_100)
- return -EINVAL;
- if (ecmd->duplex != DUPLEX_HALF && ecmd->duplex != DUPLEX_FULL)
- return -EINVAL;
- if (ecmd->port != PORT_TP)
- return -EINVAL;
- if (ecmd->transceiver != XCVR_INTERNAL)
- return -EINVAL;
- if (ecmd->autoneg != AUTONEG_DISABLE
- && ecmd->autoneg != AUTONEG_ENABLE)
- return -EINVAL;
- /* ignore phy_address, maxtxpkt, maxrxpkt for now */
-
- /* WHEW! now lets bang some bits */
-
- tmp = armiiread(dev, np->phy, MII_BMCR);
- if (ecmd->autoneg == AUTONEG_ENABLE) {
- /* turn on autonegotiation */
- tmp |= BMCR_ANENABLE;
- printk("%s: Enabling auto-neg\n", dev->name);
- } else {
- /* turn off auto negotiation, set speed and duplexity */
- tmp &= ~(BMCR_ANENABLE | BMCR_SPEED100 | BMCR_FULLDPLX);
- if (ecmd->speed == SPEED_100)
- tmp |= BMCR_SPEED100;
- if (ecmd->duplex == DUPLEX_FULL)
- tmp |= BMCR_FULLDPLX;
- printk("%s: Hard coding %d/%s\n", dev->name,
- (ecmd->speed == SPEED_100) ? 100 : 10,
- (ecmd->duplex == DUPLEX_FULL) ? "full" : "half");
- }
- armiiwrite(dev, np->phy, MII_BMCR, tmp);
- np->phyData = 0;
- return 0;
-}
-
-static int netdev_ethtool_ioctl(struct net_device *dev, void *useraddr)
-{
- struct ar2313_private *np = dev->priv;
- u32 cmd;
-
- if (get_user(cmd, (u32 *) useraddr))
- return -EFAULT;
-
- switch (cmd) {
- /* get settings */
- case ETHTOOL_GSET:{
- struct ethtool_cmd ecmd = { ETHTOOL_GSET };
- spin_lock_irq(&np->lock);
- netdev_get_ecmd(dev, &ecmd);
- spin_unlock_irq(&np->lock);
- if (copy_to_user(useraddr, &ecmd, sizeof(ecmd)))
- return -EFAULT;
- return 0;
- }
- /* set settings */
- case ETHTOOL_SSET:{
- struct ethtool_cmd ecmd;
- int r;
- if (copy_from_user(&ecmd, useraddr, sizeof(ecmd)))
- return -EFAULT;
- spin_lock_irq(&np->lock);
- r = netdev_set_ecmd(dev, &ecmd);
- spin_unlock_irq(&np->lock);
- return r;
- }
- /* restart autonegotiation */
- case ETHTOOL_NWAY_RST:{
- int tmp;
- int r = -EINVAL;
- /* if autoneg is off, it's an error */
- tmp = armiiread(dev, np->phy, MII_BMCR);
- if (tmp & BMCR_ANENABLE) {
- tmp |= (BMCR_ANRESTART);
- armiiwrite(dev, np->phy, MII_BMCR, tmp);
- r = 0;
- }
- return r;
- }
- /* get link status */
- case ETHTOOL_GLINK:{
- struct ethtool_value edata = { ETHTOOL_GLINK };
- edata.data =
- (armiiread(dev, np->phy, MII_BMSR) & BMSR_LSTATUS) ? 1 : 0;
- if (copy_to_user(useraddr, &edata, sizeof(edata)))
- return -EFAULT;
- return 0;
- }
- }
-
- return -EOPNOTSUPP;
-}
-
static int ar2313_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
{
struct mii_ioctl_data *data = (struct mii_ioctl_data *) &ifr->ifr_data;
-
+ struct ar2313_private *sp = dev->priv;
+ int ret;
+
switch (cmd) {
case SIOCETHTOOL:
- return netdev_ethtool_ioctl(dev, (void *) ifr->ifr_data);
-
- case SIOCGMIIPHY: /* Get address of MII PHY in use. */
- data->phy_id = 1;
- /* Fall Through */
-
- case SIOCGMIIREG: /* Read MII PHY register. */
- data->val_out = armiiread(dev, data->phy_id & 0x1f,
- data->reg_num & 0x1f);
- return 0;
- case SIOCSMIIREG: /* Write MII PHY register. */
- if (!capable(CAP_NET_ADMIN))
- return -EPERM;
- armiiwrite(dev, data->phy_id & 0x1f,
- data->reg_num & 0x1f, data->val_in);
- return 0;
+ spin_lock_irq(&sp->lock);
+ ret = phy_ethtool_ioctl(sp->phy_dev, (void *) ifr->ifr_data);
+ spin_unlock_irq(&sp->lock);
+ return ret;
case SIOCSIFHWADDR:
if (copy_from_user
(ifr->ifr_data, dev->dev_addr, sizeof(dev->dev_addr)))
return -EFAULT;
return 0;
-
+
+ case SIOCGMIIPHY:
+ case SIOCGMIIREG:
+ case SIOCSMIIREG:
+ return phy_mii_ioctl(sp->phy_dev, data, cmd);
+
default:
break;
}
}
+static void ar2313_adjust_link(struct net_device *dev)
+{
+ printk(KERN_ERR " ar2313_adjust_link implementation missing\n");
+}
+
#define MII_ADDR(phy, reg) \
((reg << MII_ADDR_REG_SHIFT) | (phy << MII_ADDR_PHY_SHIFT))
-static short armiiread(struct net_device *dev, short phy, short reg)
+static int
+mdiobus_read(struct mii_bus *bus, int phy_addr, int regnum)
{
+ struct net_device *const dev = bus->priv;
struct ar2313_private *sp = (struct ar2313_private *) dev->priv;
volatile ETHERNET_STRUCT *ethernet = sp->phy_regs;
- ethernet->mii_addr = MII_ADDR(phy, reg);
+ ethernet->mii_addr = MII_ADDR(phy_addr, regnum);
while (ethernet->mii_addr & MII_ADDR_BUSY);
return (ethernet->mii_data >> MII_DATA_SHIFT);
}
-static void
-armiiwrite(struct net_device *dev, short phy, short reg, short data)
+static int
+mdiobus_write(struct mii_bus *bus, int phy_addr, int regnum,
+ u16 value)
{
+ struct net_device *const dev = bus->priv;
struct ar2313_private *sp = (struct ar2313_private *) dev->priv;
volatile ETHERNET_STRUCT *ethernet = sp->phy_regs;
while (ethernet->mii_addr & MII_ADDR_BUSY);
- ethernet->mii_data = data << MII_DATA_SHIFT;
- ethernet->mii_addr = MII_ADDR(phy, reg) | MII_ADDR_WRITE;
+ ethernet->mii_data = value << MII_DATA_SHIFT;
+ ethernet->mii_addr = MII_ADDR(phy_addr, regnum) | MII_ADDR_WRITE;
+
+ return 0;
+}
+
+static int mdiobus_reset(struct mii_bus *bus)
+{
+ struct net_device *const dev = bus->priv;
+
+ ar2313_reset_reg(dev);
+
+ return 0;
+}
+
+static int mdiobus_probe (struct net_device *dev)
+{
+ struct ar2313_private *const sp = (struct ar2313_private *) dev->priv;
+ struct phy_device *phydev = NULL;
+ int phy_addr;
+
+ /* find the first (lowest address) PHY on the current MAC's MII bus */
+ for (phy_addr = 0; phy_addr < PHY_MAX_ADDR; phy_addr++)
+ if (sp->mii_bus.phy_map[phy_addr]) {
+ phydev = sp->mii_bus.phy_map[phy_addr];
+ break; /* break out with first one found */
+ }
+
+ if (!phydev) {
+ printk (KERN_ERR "ar2313:%s: no PHY found\n", dev->name);
+ return -1;
+ }
+
+ /* now we are supposed to have a proper phydev, to attach to... */
+ BUG_ON(!phydev);
+ BUG_ON(phydev->attached_dev);
+
+ phydev = phy_connect(dev, phydev->dev.bus_id, &ar2313_adjust_link, 0,
+ PHY_INTERFACE_MODE_MII);
+
+ if (IS_ERR(phydev)) {
+ printk(KERN_ERR "%s: Could not attach to PHY\n", dev->name);
+ return PTR_ERR(phydev);
+ }
+
+ /* mask with MAC supported features */
+ phydev->supported &= (SUPPORTED_10baseT_Half
+ | SUPPORTED_10baseT_Full
+ | SUPPORTED_100baseT_Half
+ | SUPPORTED_100baseT_Full
+ | SUPPORTED_Autoneg
+ /* | SUPPORTED_Pause | SUPPORTED_Asym_Pause */
+ | SUPPORTED_MII
+ | SUPPORTED_TP);
+
+ phydev->advertising = phydev->supported;
+
+ //sp->old_link = 0;
+ //sp->old_speed = 0;
+ //sp->old_duplex = -1;
+ sp->phy_dev = phydev;
+
+ printk(KERN_INFO "%s: attached PHY driver [%s] "
+ "(mii_bus:phy_addr=%s)\n",
+ dev->name, phydev->drv->name, phydev->dev.bus_id);
+
+ return 0;
}
+
projects / openwrt.git / blobdiff