++err_device_add:
++ free_irq(irq, udc);
++err_request_irq:
++ iounmap(udc->fifo);
++err_map_fifo:
++ iounmap(udc->regs);
++err_map_regs:
++ clk_put(hclk);
++err_get_hclk:
++ clk_put(pclk);
++
++ platform_set_drvdata(pdev, NULL);
++
++ return ret;
++}
++
++static int __exit usba_udc_remove(struct platform_device *pdev)
++{
++ struct usba_udc *udc;
++ int i;
++
++ udc = platform_get_drvdata(pdev);
++
++ for (i = 1; i < ARRAY_SIZE(usba_ep); i++)
++ usba_ep_cleanup_debugfs(&usba_ep[i]);
++ usba_cleanup_debugfs(udc);
++
++ if (udc->vbus_pin != -1)
++ gpio_free(udc->vbus_pin);
++
++ free_irq(udc->irq, udc);
++ iounmap(udc->fifo);
++ iounmap(udc->regs);
++ clk_put(udc->hclk);
++ clk_put(udc->pclk);
++
++ device_unregister(&udc->gadget.dev);
++
++ return 0;
++}
++
++static struct platform_driver udc_driver = {
++ .remove = __exit_p(usba_udc_remove),
++ .driver = {
++ .name = "atmel_usba_udc",
++ },
++};
++
++static int __init udc_init(void)
++{
++ return platform_driver_probe(&udc_driver, usba_udc_probe);
++}
++module_init(udc_init);
++
++static void __exit udc_exit(void)
++{
++ platform_driver_unregister(&udc_driver);
++}
++module_exit(udc_exit);
++
++MODULE_DESCRIPTION("Atmel USBA UDC driver");
++MODULE_AUTHOR("Haavard Skinnemoen <hskinnemoen@atmel.com>");
++MODULE_LICENSE("GPL");
+diff --git a/drivers/usb/gadget/atmel_usba_udc.h b/drivers/usb/gadget/atmel_usba_udc.h
+new file mode 100644
+index 0000000..f4f0f8b
+--- /dev/null
++++ b/drivers/usb/gadget/atmel_usba_udc.h
+@@ -0,0 +1,350 @@
++/*
++ * Driver for the Atmel USBA high speed USB device controller
++ *
++ * Copyright (C) 2005-2007 Atmel Corporation
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 as
++ * published by the Free Software Foundation.
++ */
++#ifndef __LINUX_USB_GADGET_USBA_UDC_H__
++#define __LINUX_USB_GADGET_USBA_UDC_H__
++
++/* USB register offsets */
++#define USBA_CTRL 0x0000
++#define USBA_FNUM 0x0004
++#define USBA_INT_ENB 0x0010
++#define USBA_INT_STA 0x0014
++#define USBA_INT_CLR 0x0018
++#define USBA_EPT_RST 0x001c
++#define USBA_TST 0x00e0
++
++/* USB endpoint register offsets */
++#define USBA_EPT_CFG 0x0000
++#define USBA_EPT_CTL_ENB 0x0004
++#define USBA_EPT_CTL_DIS 0x0008
++#define USBA_EPT_CTL 0x000c
++#define USBA_EPT_SET_STA 0x0014
++#define USBA_EPT_CLR_STA 0x0018
++#define USBA_EPT_STA 0x001c
++
++/* USB DMA register offsets */
++#define USBA_DMA_NXT_DSC 0x0000
++#define USBA_DMA_ADDRESS 0x0004
++#define USBA_DMA_CONTROL 0x0008
++#define USBA_DMA_STATUS 0x000c
++
++/* Bitfields in CTRL */
++#define USBA_DEV_ADDR_OFFSET 0
++#define USBA_DEV_ADDR_SIZE 7
++#define USBA_FADDR_EN (1 << 7)
++#define USBA_EN_USBA (1 << 8)
++#define USBA_DETACH (1 << 9)
++#define USBA_REMOTE_WAKE_UP (1 << 10)
++
++/* Bitfields in FNUM */
++#define USBA_MICRO_FRAME_NUM_OFFSET 0
++#define USBA_MICRO_FRAME_NUM_SIZE 3
++#define USBA_FRAME_NUMBER_OFFSET 3
++#define USBA_FRAME_NUMBER_SIZE 11
++#define USBA_FRAME_NUM_ERROR (1 << 31)
++
++/* Bitfields in INT_ENB/INT_STA/INT_CLR */
++#define USBA_HIGH_SPEED (1 << 0)
++#define USBA_DET_SUSPEND (1 << 1)
++#define USBA_MICRO_SOF (1 << 2)
++#define USBA_SOF (1 << 3)
++#define USBA_END_OF_RESET (1 << 4)
++#define USBA_WAKE_UP (1 << 5)
++#define USBA_END_OF_RESUME (1 << 6)
++#define USBA_UPSTREAM_RESUME (1 << 7)
++#define USBA_EPT_INT_OFFSET 8
++#define USBA_EPT_INT_SIZE 16
++#define USBA_DMA_INT_OFFSET 24
++#define USBA_DMA_INT_SIZE 8
++
++/* Bitfields in EPT_RST */
++#define USBA_RST_OFFSET 0
++#define USBA_RST_SIZE 16
++
++/* Bitfields in USBA_TST */
++#define USBA_SPEED_CFG_OFFSET 0
++#define USBA_SPEED_CFG_SIZE 2
++#define USBA_TST_J_MODE (1 << 2)
++#define USBA_TST_K_MODE (1 << 3)
++#define USBA_TST_PKT_MODE (1 << 4)
++#define USBA_OPMODE2 (1 << 5)
++
++/* Bitfields in EPT_CFG */
++#define USBA_EPT_SIZE_OFFSET 0
++#define USBA_EPT_SIZE_SIZE 3
++#define USBA_EPT_DIR_IN (1 << 3)
++#define USBA_EPT_TYPE_OFFSET 4
++#define USBA_EPT_TYPE_SIZE 2
++#define USBA_BK_NUMBER_OFFSET 6
++#define USBA_BK_NUMBER_SIZE 2
++#define USBA_NB_TRANS_OFFSET 8
++#define USBA_NB_TRANS_SIZE 2
++#define USBA_EPT_MAPPED (1 << 31)
++
++/* Bitfields in EPT_CTL/EPT_CTL_ENB/EPT_CTL_DIS */
++#define USBA_EPT_ENABLE (1 << 0)
++#define USBA_AUTO_VALID (1 << 1)
++#define USBA_INTDIS_DMA (1 << 3)
++#define USBA_NYET_DIS (1 << 4)
++#define USBA_DATAX_RX (1 << 6)
++#define USBA_MDATA_RX (1 << 7)
++/* Bits 8-15 and 31 enable interrupts for respective bits in EPT_STA */
++#define USBA_BUSY_BANK_IE (1 << 18)
++
++/* Bitfields in EPT_SET_STA/EPT_CLR_STA/EPT_STA */
++#define USBA_FORCE_STALL (1 << 5)
++#define USBA_TOGGLE_CLR (1 << 6)
++#define USBA_TOGGLE_SEQ_OFFSET 6
++#define USBA_TOGGLE_SEQ_SIZE 2
++#define USBA_ERR_OVFLW (1 << 8)
++#define USBA_RX_BK_RDY (1 << 9)
++#define USBA_KILL_BANK (1 << 9)
++#define USBA_TX_COMPLETE (1 << 10)
++#define USBA_TX_PK_RDY (1 << 11)
++#define USBA_ISO_ERR_TRANS (1 << 11)
++#define USBA_RX_SETUP (1 << 12)
++#define USBA_ISO_ERR_FLOW (1 << 12)
++#define USBA_STALL_SENT (1 << 13)
++#define USBA_ISO_ERR_CRC (1 << 13)
++#define USBA_ISO_ERR_NBTRANS (1 << 13)
++#define USBA_NAK_IN (1 << 14)
++#define USBA_ISO_ERR_FLUSH (1 << 14)
++#define USBA_NAK_OUT (1 << 15)
++#define USBA_CURRENT_BANK_OFFSET 16
++#define USBA_CURRENT_BANK_SIZE 2
++#define USBA_BUSY_BANKS_OFFSET 18
++#define USBA_BUSY_BANKS_SIZE 2
++#define USBA_BYTE_COUNT_OFFSET 20
++#define USBA_BYTE_COUNT_SIZE 11
++#define USBA_SHORT_PACKET (1 << 31)
++
++/* Bitfields in DMA_CONTROL */
++#define USBA_DMA_CH_EN (1 << 0)
++#define USBA_DMA_LINK (1 << 1)
++#define USBA_DMA_END_TR_EN (1 << 2)
++#define USBA_DMA_END_BUF_EN (1 << 3)
++#define USBA_DMA_END_TR_IE (1 << 4)
++#define USBA_DMA_END_BUF_IE (1 << 5)
++#define USBA_DMA_DESC_LOAD_IE (1 << 6)
++#define USBA_DMA_BURST_LOCK (1 << 7)
++#define USBA_DMA_BUF_LEN_OFFSET 16
++#define USBA_DMA_BUF_LEN_SIZE 16
++
++/* Bitfields in DMA_STATUS */
++#define USBA_DMA_CH_ACTIVE (1 << 1)
++#define USBA_DMA_END_TR_ST (1 << 4)
++#define USBA_DMA_END_BUF_ST (1 << 5)
++#define USBA_DMA_DESC_LOAD_ST (1 << 6)
++
++/* Constants for SPEED_CFG */
++#define USBA_SPEED_CFG_NORMAL 0
++#define USBA_SPEED_CFG_FORCE_HIGH 2
++#define USBA_SPEED_CFG_FORCE_FULL 3
++
++/* Constants for EPT_SIZE */
++#define USBA_EPT_SIZE_8 0
++#define USBA_EPT_SIZE_16 1
++#define USBA_EPT_SIZE_32 2
++#define USBA_EPT_SIZE_64 3
++#define USBA_EPT_SIZE_128 4
++#define USBA_EPT_SIZE_256 5
++#define USBA_EPT_SIZE_512 6
++#define USBA_EPT_SIZE_1024 7
++
++/* Constants for EPT_TYPE */
++#define USBA_EPT_TYPE_CONTROL 0
++#define USBA_EPT_TYPE_ISO 1
++#define USBA_EPT_TYPE_BULK 2
++#define USBA_EPT_TYPE_INT 3
++
++/* Constants for BK_NUMBER */
++#define USBA_BK_NUMBER_ZERO 0
++#define USBA_BK_NUMBER_ONE 1
++#define USBA_BK_NUMBER_DOUBLE 2
++#define USBA_BK_NUMBER_TRIPLE 3
++
++/* Bit manipulation macros */
++#define USBA_BF(name, value) \
++ (((value) & ((1 << USBA_##name##_SIZE) - 1)) \
++ << USBA_##name##_OFFSET)
++#define USBA_BFEXT(name, value) \
++ (((value) >> USBA_##name##_OFFSET) \
++ & ((1 << USBA_##name##_SIZE) - 1))
++#define USBA_BFINS(name, value, old) \
++ (((old) & ~(((1 << USBA_##name##_SIZE) - 1) \
++ << USBA_##name##_OFFSET)) \
++ | USBA_BF(name, value))
++
++/* Register access macros */
++#define usba_readl(udc, reg) \
++ __raw_readl((udc)->regs + USBA_##reg)
++#define usba_writel(udc, reg, value) \
++ __raw_writel((value), (udc)->regs + USBA_##reg)
++#define usba_ep_readl(ep, reg) \
++ __raw_readl((ep)->ep_regs + USBA_EPT_##reg)
++#define usba_ep_writel(ep, reg, value) \
++ __raw_writel((value), (ep)->ep_regs + USBA_EPT_##reg)
++#define usba_dma_readl(ep, reg) \
++ __raw_readl((ep)->dma_regs + USBA_DMA_##reg)
++#define usba_dma_writel(ep, reg, value) \
++ __raw_writel((value), (ep)->dma_regs + USBA_DMA_##reg)
++
++/* Calculate base address for a given endpoint or DMA controller */
++#define USBA_EPT_BASE(x) (0x100 + (x) * 0x20)
++#define USBA_DMA_BASE(x) (0x300 + (x) * 0x10)
++#define USBA_FIFO_BASE(x) ((x) << 16)
++
++/* Synth parameters */
++#define USBA_NR_ENDPOINTS 7
++
++#define EP0_FIFO_SIZE 64
++#define EP0_EPT_SIZE USBA_EPT_SIZE_64
++#define EP0_NR_BANKS 1
++
++/*
++ * REVISIT: Try to eliminate this value. Can we rely on req->mapped to
++ * provide this information?
++ */
++#define DMA_ADDR_INVALID (~(dma_addr_t)0)
++
++#define FIFO_IOMEM_ID 0
++#define CTRL_IOMEM_ID 1
++
++#ifdef DEBUG
++#define DBG_ERR 0x0001 /* report all error returns */
++#define DBG_HW 0x0002 /* debug hardware initialization */
++#define DBG_GADGET 0x0004 /* calls to/from gadget driver */
++#define DBG_INT 0x0008 /* interrupts */
++#define DBG_BUS 0x0010 /* report changes in bus state */
++#define DBG_QUEUE 0x0020 /* debug request queue processing */
++#define DBG_FIFO 0x0040 /* debug FIFO contents */
++#define DBG_DMA 0x0080 /* debug DMA handling */
++#define DBG_REQ 0x0100 /* print out queued request length */
++#define DBG_ALL 0xffff
++#define DBG_NONE 0x0000
++
++#define DEBUG_LEVEL (DBG_ERR)
++#define DBG(level, fmt, ...) \
++ do { \
++ if ((level) & DEBUG_LEVEL) \
++ printk(KERN_DEBUG "udc: " fmt, ## __VA_ARGS__); \
++ } while (0)
++#else
++#define DBG(level, fmt...)
++#endif
++
++enum usba_ctrl_state {
++ WAIT_FOR_SETUP,
++ DATA_STAGE_IN,
++ DATA_STAGE_OUT,
++ STATUS_STAGE_IN,
++ STATUS_STAGE_OUT,
++ STATUS_STAGE_ADDR,
++ STATUS_STAGE_TEST,
++};
++/*
++ EP_STATE_IDLE,
++ EP_STATE_SETUP,
++ EP_STATE_IN_DATA,
++ EP_STATE_OUT_DATA,
++ EP_STATE_SET_ADDR_STATUS,
++ EP_STATE_RX_STATUS,
++ EP_STATE_TX_STATUS,
++ EP_STATE_HALT,
++*/
++
++struct usba_dma_desc {
++ dma_addr_t next;
++ dma_addr_t addr;
++ u32 ctrl;
++};
++
++struct usba_ep {
++ int state;
++ void __iomem *ep_regs;
++ void __iomem *dma_regs;
++ void __iomem *fifo;
++ struct usb_ep ep;
++ struct usba_udc *udc;
++
++ struct list_head queue;
++ const struct usb_endpoint_descriptor *desc;
++
++ u16 fifo_size;
++ u8 nr_banks;
++ u8 index;
++ unsigned int can_dma:1;
++ unsigned int can_isoc:1;
++ unsigned int is_isoc:1;
++ unsigned int is_in:1;
++
++#ifdef CONFIG_USB_GADGET_DEBUG_FS
++ u32 last_dma_status;
++ struct dentry *debugfs_dir;
++ struct dentry *debugfs_queue;
++ struct dentry *debugfs_dma_status;
++ struct dentry *debugfs_state;
++#endif
++};
++
++struct usba_request {
++ struct usb_request req;
++ struct list_head queue;
++
++ u32 ctrl;
++
++ unsigned int submitted:1;
++ unsigned int last_transaction:1;
++ unsigned int using_dma:1;
++ unsigned int mapped:1;
++};
++
++struct usba_udc {
++ /* Protect hw registers from concurrent modifications */
++ spinlock_t lock;
++
++ void __iomem *regs;
++ void __iomem *fifo;
++
++ struct usb_gadget gadget;
++ struct usb_gadget_driver *driver;
++ struct platform_device *pdev;
++ int irq;
++ int vbus_pin;
++ struct clk *pclk;
++ struct clk *hclk;
++
++ int test_mode;
++ int vbus_prev;
++
++#ifdef CONFIG_USB_GADGET_DEBUG_FS
++ struct dentry *debugfs_root;
++ struct dentry *debugfs_regs;
++#endif
++};
++
++static inline struct usba_ep *to_usba_ep(struct usb_ep *ep)
++{
++ return container_of(ep, struct usba_ep, ep);
++}
++
++static inline struct usba_request *to_usba_req(struct usb_request *req)
++{
++ return container_of(req, struct usba_request, req);
++}
++
++static inline struct usba_udc *to_usba_udc(struct usb_gadget *gadget)
++{
++ return container_of(gadget, struct usba_udc, gadget);
++}
++
++#define ep_is_control(ep) ((ep)->index == 0)
++#define ep_is_idle(ep) ((ep)->state == EP_STATE_IDLE)
++
++#endif /* __LINUX_USB_GADGET_USBA_UDC_H */
+diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
+index 235b618..bb361ab 100644
+--- a/drivers/video/atmel_lcdfb.c
++++ b/drivers/video/atmel_lcdfb.c
+@@ -37,7 +37,9 @@
+ #endif
+
+ #if defined(CONFIG_ARCH_AT91)
+-#define ATMEL_LCDFB_FBINFO_DEFAULT FBINFO_DEFAULT
++#define ATMEL_LCDFB_FBINFO_DEFAULT (FBINFO_DEFAULT \
++ | FBINFO_PARTIAL_PAN_OK \
++ | FBINFO_HWACCEL_YPAN)
+
+ static inline void atmel_lcdfb_update_dma2d(struct atmel_lcdfb_info *sinfo,
+ struct fb_var_screeninfo *var)
+@@ -74,7 +76,7 @@ static struct fb_fix_screeninfo atmel_lcdfb_fix __initdata = {
+ .type = FB_TYPE_PACKED_PIXELS,
+ .visual = FB_VISUAL_TRUECOLOR,
+ .xpanstep = 0,
+- .ypanstep = 0,
++ .ypanstep = 1,
+ .ywrapstep = 0,
+ .accel = FB_ACCEL_NONE,
+ };
+diff --git a/drivers/video/backlight/Kconfig b/drivers/video/backlight/Kconfig
+index 2580f5f..b6f936a 100644
+--- a/drivers/video/backlight/Kconfig
++++ b/drivers/video/backlight/Kconfig
+@@ -24,6 +24,18 @@ config LCD_CLASS_DEVICE
+ To have support for your specific LCD panel you will have to
+ select the proper drivers which depend on this option.
+
++config LCD_LTV350QV
++ tristate "Samsung LTV350QV LCD Panel"
++ depends on LCD_CLASS_DEVICE && SPI_MASTER
++ default n
++ help
++ If you have a Samsung LTV350QV LCD panel, say y to include a
++ power control driver for it. The panel starts up in power
++ off state, so you need this driver in order to see any
++ output.
++
++ The LTV350QV panel is present on all ATSTK1000 boards.
++
+ #
+ # Backlight
+ #
+diff --git a/drivers/video/backlight/Makefile b/drivers/video/backlight/Makefile
+index c6e2266..965a78b 100644
+--- a/drivers/video/backlight/Makefile
++++ b/drivers/video/backlight/Makefile
+@@ -1,6 +1,8 @@
+ # Backlight & LCD drivers
+
+ obj-$(CONFIG_LCD_CLASS_DEVICE) += lcd.o
++obj-$(CONFIG_LCD_LTV350QV) += ltv350qv.o
++
+ obj-$(CONFIG_BACKLIGHT_CLASS_DEVICE) += backlight.o
+ obj-$(CONFIG_BACKLIGHT_CORGI) += corgi_bl.o
+ obj-$(CONFIG_BACKLIGHT_HP680) += hp680_bl.o
+diff --git a/drivers/video/backlight/ltv350qv.c b/drivers/video/backlight/ltv350qv.c
+new file mode 100644
+index 0000000..751dc53
+--- /dev/null
++++ b/drivers/video/backlight/ltv350qv.c
+@@ -0,0 +1,339 @@
++/*
++ * Power control for Samsung LTV350QV Quarter VGA LCD Panel
++ *
++ * Copyright (C) 2006, 2007 Atmel Corporation
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 as
++ * published by the Free Software Foundation.
++ */
++#include <linux/delay.h>
++#include <linux/err.h>
++#include <linux/fb.h>
++#include <linux/init.h>
++#include <linux/lcd.h>
++#include <linux/module.h>
++#include <linux/spi/spi.h>
++
++#include "ltv350qv.h"
++
++#define POWER_IS_ON(pwr) ((pwr) <= FB_BLANK_NORMAL)
++
++struct ltv350qv {
++ struct spi_device *spi;
++ u8 *buffer;
++ int power;
++ struct lcd_device *ld;
++};
++
++/*
++ * The power-on and power-off sequences are taken from the
++ * LTV350QV-F04 data sheet from Samsung. The register definitions are
++ * taken from the S6F2002 command list also from Samsung. Both
++ * documents are distributed with the AVR32 Linux BSP CD from Atmel.
++ *
++ * There's still some voodoo going on here, but it's a lot better than
++ * in the first incarnation of the driver where all we had was the raw
++ * numbers from the initialization sequence.
++ */
++static int ltv350qv_write_reg(struct ltv350qv *lcd, u8 reg, u16 val)
++{
++ struct spi_message msg;
++ struct spi_transfer index_xfer = {
++ .len = 3,
++ .cs_change = 1,
++ };
++ struct spi_transfer value_xfer = {
++ .len = 3,
++ };
++
++ spi_message_init(&msg);
++
++ /* register index */
++ lcd->buffer[0] = LTV_OPC_INDEX;
++ lcd->buffer[1] = 0x00;
++ lcd->buffer[2] = reg & 0x7f;
++ index_xfer.tx_buf = lcd->buffer;
++ spi_message_add_tail(&index_xfer, &msg);
++
++ /* register value */
++ lcd->buffer[4] = LTV_OPC_DATA;
++ lcd->buffer[5] = val >> 8;
++ lcd->buffer[6] = val;
++ value_xfer.tx_buf = lcd->buffer + 4;
++ spi_message_add_tail(&value_xfer, &msg);
++
++ return spi_sync(lcd->spi, &msg);
++}
++
++/* The comments are taken straight from the data sheet */
++static int ltv350qv_power_on(struct ltv350qv *lcd)
++{
++ int ret;
++
++ /* Power On Reset Display off State */
++ if (ltv350qv_write_reg(lcd, LTV_PWRCTL1, 0x0000))
++ goto err;
++ msleep(15);
++
++ /* Power Setting Function 1 */
++ if (ltv350qv_write_reg(lcd, LTV_PWRCTL1, LTV_VCOM_DISABLE))
++ goto err;
++ if (ltv350qv_write_reg(lcd, LTV_PWRCTL2, LTV_VCOML_ENABLE))
++ goto err_power1;
++
++ /* Power Setting Function 2 */
++ if (ltv350qv_write_reg(lcd, LTV_PWRCTL1,
++ LTV_VCOM_DISABLE | LTV_DRIVE_CURRENT(5)
++ | LTV_SUPPLY_CURRENT(5)))
++ goto err_power2;
++
++ msleep(55);
++
++ /* Instruction Setting */
++ ret = ltv350qv_write_reg(lcd, LTV_IFCTL,
++ LTV_NMD | LTV_REV | LTV_NL(0x1d));
++ ret |= ltv350qv_write_reg(lcd, LTV_DATACTL,
++ LTV_DS_SAME | LTV_CHS_480
++ | LTV_DF_RGB | LTV_RGB_BGR);
++ ret |= ltv350qv_write_reg(lcd, LTV_ENTRY_MODE,
++ LTV_VSPL_ACTIVE_LOW
++ | LTV_HSPL_ACTIVE_LOW
++ | LTV_DPL_SAMPLE_RISING
++ | LTV_EPL_ACTIVE_LOW
++ | LTV_SS_RIGHT_TO_LEFT);
++ ret |= ltv350qv_write_reg(lcd, LTV_GATECTL1, LTV_CLW(3));
++ ret |= ltv350qv_write_reg(lcd, LTV_GATECTL2,
++ LTV_NW_INV_1LINE | LTV_FWI(3));
++ ret |= ltv350qv_write_reg(lcd, LTV_VBP, 0x000a);
++ ret |= ltv350qv_write_reg(lcd, LTV_HBP, 0x0021);
++ ret |= ltv350qv_write_reg(lcd, LTV_SOTCTL, LTV_SDT(3) | LTV_EQ(0));
++ ret |= ltv350qv_write_reg(lcd, LTV_GAMMA(0), 0x0103);
++ ret |= ltv350qv_write_reg(lcd, LTV_GAMMA(1), 0x0301);
++ ret |= ltv350qv_write_reg(lcd, LTV_GAMMA(2), 0x1f0f);
++ ret |= ltv350qv_write_reg(lcd, LTV_GAMMA(3), 0x1f0f);
++ ret |= ltv350qv_write_reg(lcd, LTV_GAMMA(4), 0x0707);
++ ret |= ltv350qv_write_reg(lcd, LTV_GAMMA(5), 0x0307);
++ ret |= ltv350qv_write_reg(lcd, LTV_GAMMA(6), 0x0707);
++ ret |= ltv350qv_write_reg(lcd, LTV_GAMMA(7), 0x0000);
++ ret |= ltv350qv_write_reg(lcd, LTV_GAMMA(8), 0x0004);
++ ret |= ltv350qv_write_reg(lcd, LTV_GAMMA(9), 0x0000);
++ if (ret)
++ goto err_settings;
++
++ /* Wait more than 2 frames */
++ msleep(20);
++
++ /* Display On Sequence */
++ ret = ltv350qv_write_reg(lcd, LTV_PWRCTL1,
++ LTV_VCOM_DISABLE | LTV_VCOMOUT_ENABLE
++ | LTV_POWER_ON | LTV_DRIVE_CURRENT(5)
++ | LTV_SUPPLY_CURRENT(5));
++ ret |= ltv350qv_write_reg(lcd, LTV_GATECTL2,
++ LTV_NW_INV_1LINE | LTV_DSC | LTV_FWI(3));
++ if (ret)
++ goto err_disp_on;
++
++ /* Display should now be ON. Phew. */
++ return 0;
++
++err_disp_on:
++ /*
++ * Try to recover. Error handling probably isn't very useful
++ * at this point, just make a best effort to switch the panel
++ * off.
++ */
++ ltv350qv_write_reg(lcd, LTV_PWRCTL1,
++ LTV_VCOM_DISABLE | LTV_DRIVE_CURRENT(5)
++ | LTV_SUPPLY_CURRENT(5));
++ ltv350qv_write_reg(lcd, LTV_GATECTL2,
++ LTV_NW_INV_1LINE | LTV_FWI(3));
++err_settings:
++err_power2:
++err_power1:
++ ltv350qv_write_reg(lcd, LTV_PWRCTL2, 0x0000);
++ msleep(1);
++err:
++ ltv350qv_write_reg(lcd, LTV_PWRCTL1, LTV_VCOM_DISABLE);
++ return -EIO;
++}
++
++static int ltv350qv_power_off(struct ltv350qv *lcd)
++{
++ int ret;
++
++ /* Display Off Sequence */
++ ret = ltv350qv_write_reg(lcd, LTV_PWRCTL1,
++ LTV_VCOM_DISABLE
++ | LTV_DRIVE_CURRENT(5)
++ | LTV_SUPPLY_CURRENT(5));
++ ret |= ltv350qv_write_reg(lcd, LTV_GATECTL2,
++ LTV_NW_INV_1LINE | LTV_FWI(3));
++
++ /* Power down setting 1 */
++ ret |= ltv350qv_write_reg(lcd, LTV_PWRCTL2, 0x0000);
++
++ /* Wait at least 1 ms */
++ msleep(1);
++
++ /* Power down setting 2 */
++ ret |= ltv350qv_write_reg(lcd, LTV_PWRCTL1, LTV_VCOM_DISABLE);
++
++ /*
++ * No point in trying to recover here. If we can't switch the
++ * panel off, what are we supposed to do other than inform the
++ * user about the failure?
++ */
++ if (ret)
++ return -EIO;
++
++ /* Display power should now be OFF */
++ return 0;
++}
++
++static int ltv350qv_power(struct ltv350qv *lcd, int power)
++{
++ int ret = 0;
++
++ if (POWER_IS_ON(power) && !POWER_IS_ON(lcd->power))
++ ret = ltv350qv_power_on(lcd);
++ else if (!POWER_IS_ON(power) && POWER_IS_ON(lcd->power))
++ ret = ltv350qv_power_off(lcd);
++
++ if (!ret)
++ lcd->power = power;
++
++ return ret;
++}
++
++static int ltv350qv_set_power(struct lcd_device *ld, int power)
++{
++ struct ltv350qv *lcd;
++
++ lcd = lcd_get_data(ld);
++ return ltv350qv_power(lcd, power);
++}
++
++static int ltv350qv_get_power(struct lcd_device *ld)
++{
++ struct ltv350qv *lcd;
++
++ lcd = lcd_get_data(ld);
++ return lcd->power;
++}
++
++static struct lcd_ops ltv_ops = {
++ .get_power = ltv350qv_get_power,
++ .set_power = ltv350qv_set_power,
++};
++
++static int __devinit ltv350qv_probe(struct spi_device *spi)
++{
++ struct ltv350qv *lcd;
++ struct lcd_device *ld;
++ int ret;
++
++ lcd = kzalloc(sizeof(struct ltv350qv), GFP_KERNEL);
++ if (!lcd)
++ return -ENOMEM;
++
++ lcd->spi = spi;
++ lcd->power = FB_BLANK_POWERDOWN;
++ lcd->buffer = kzalloc(8, GFP_KERNEL);
++
++ ld = lcd_device_register("ltv350qv", &spi->dev, lcd, <v_ops);
++ if (IS_ERR(ld)) {
++ ret = PTR_ERR(ld);
++ goto out_free_lcd;
++ }
++ lcd->ld = ld;
++
++ ret = ltv350qv_power(lcd, FB_BLANK_UNBLANK);
++ if (ret)
++ goto out_unregister;
++
++ dev_set_drvdata(&spi->dev, lcd);
++
++ return 0;
++
++out_unregister:
++ lcd_device_unregister(ld);
++out_free_lcd:
++ kfree(lcd);
++ return ret;
++}
++
++static int __devexit ltv350qv_remove(struct spi_device *spi)
++{
++ struct ltv350qv *lcd = dev_get_drvdata(&spi->dev);
++
++ ltv350qv_power(lcd, FB_BLANK_POWERDOWN);
++ lcd_device_unregister(lcd->ld);
++ kfree(lcd);
++
++ return 0;
++}
++
++#ifdef CONFIG_PM
++static int ltv350qv_suspend(struct spi_device *spi,
++ pm_message_t state, u32 level)
++{
++ struct ltv350qv *lcd = dev_get_drvdata(&spi->dev);
++
++ if (level == SUSPEND_POWER_DOWN)
++ return ltv350qv_power(lcd, FB_BLANK_POWERDOWN);
++
++ return 0;
++}
++
++static int ltv350qv_resume(struct spi_device *spi, u32 level)
++{
++ struct ltv350qv *lcd = dev_get_drvdata(&spi->dev);
++
++ if (level == RESUME_POWER_ON)
++ return ltv350qv_power(lcd, FB_BLANK_UNBLANK);
++
++ return 0;
++}
++#else
++#define ltv350qv_suspend NULL
++#define ltv350qv_resume NULL
++#endif
++
++/* Power down all displays on reboot, poweroff or halt */
++static void ltv350qv_shutdown(struct spi_device *spi)
++{
++ struct ltv350qv *lcd = dev_get_drvdata(&spi->dev);
++
++ ltv350qv_power(lcd, FB_BLANK_POWERDOWN);
++}
++
++static struct spi_driver ltv350qv_driver = {
++ .driver = {
++ .name = "ltv350qv",
++ .bus = &spi_bus_type,
++ .owner = THIS_MODULE,
++ },
++
++ .probe = ltv350qv_probe,
++ .remove = __devexit_p(ltv350qv_remove),
++ .shutdown = ltv350qv_shutdown,
++ .suspend = ltv350qv_suspend,
++ .resume = ltv350qv_resume,
++};
++
++static int __init ltv350qv_init(void)
++{
++ return spi_register_driver(<v350qv_driver);
++}
++
++static void __exit ltv350qv_exit(void)
++{
++ spi_unregister_driver(<v350qv_driver);
++}
++module_init(ltv350qv_init);
++module_exit(ltv350qv_exit);
++
++MODULE_AUTHOR("Haavard Skinnemoen <hskinnemoen@atmel.com>");
++MODULE_DESCRIPTION("Samsung LTV350QV LCD Driver");
++MODULE_LICENSE("GPL");
+diff --git a/drivers/video/backlight/ltv350qv.h b/drivers/video/backlight/ltv350qv.h
+new file mode 100644
+index 0000000..189112e
+--- /dev/null
++++ b/drivers/video/backlight/ltv350qv.h
+@@ -0,0 +1,95 @@
++/*
++ * Register definitions for Samsung LTV350QV Quarter VGA LCD Panel
++ *
++ * Copyright (C) 2006, 2007 Atmel Corporation
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 as
++ * published by the Free Software Foundation.
++ */
++#ifndef __LTV350QV_H
++#define __LTV350QV_H
++
++#define LTV_OPC_INDEX 0x74
++#define LTV_OPC_DATA 0x76
++
++#define LTV_ID 0x00 /* ID Read */
++#define LTV_IFCTL 0x01 /* Display Interface Control */
++#define LTV_DATACTL 0x02 /* Display Data Control */
++#define LTV_ENTRY_MODE 0x03 /* Entry Mode */
++#define LTV_GATECTL1 0x04 /* Gate Control 1 */
++#define LTV_GATECTL2 0x05 /* Gate Control 2 */
++#define LTV_VBP 0x06 /* Vertical Back Porch */
++#define LTV_HBP 0x07 /* Horizontal Back Porch */
++#define LTV_SOTCTL 0x08 /* Source Output Timing Control */
++#define LTV_PWRCTL1 0x09 /* Power Control 1 */
++#define LTV_PWRCTL2 0x0a /* Power Control 2 */
++#define LTV_GAMMA(x) (0x10 + (x)) /* Gamma control */
++
++/* Bit definitions for LTV_IFCTL */
++#define LTV_IM (1 << 15)
++#define LTV_NMD (1 << 14)
++#define LTV_SSMD (1 << 13)
++#define LTV_REV (1 << 7)
++#define LTV_NL(x) (((x) & 0x001f) << 0)
++
++/* Bit definitions for LTV_DATACTL */
++#define LTV_DS_SAME (0 << 12)
++#define LTV_DS_D_TO_S (1 << 12)
++#define LTV_DS_S_TO_D (2 << 12)
++#define LTV_CHS_384 (0 << 9)
++#define LTV_CHS_480 (1 << 9)
++#define LTV_CHS_492 (2 << 9)
++#define LTV_DF_RGB (0 << 6)
++#define LTV_DF_RGBX (1 << 6)
++#define LTV_DF_XRGB (2 << 6)
++#define LTV_RGB_RGB (0 << 2)
++#define LTV_RGB_BGR (1 << 2)
++#define LTV_RGB_GRB (2 << 2)
++#define LTV_RGB_RBG (3 << 2)
++
++/* Bit definitions for LTV_ENTRY_MODE */
++#define LTV_VSPL_ACTIVE_LOW (0 << 15)
++#define LTV_VSPL_ACTIVE_HIGH (1 << 15)
++#define LTV_HSPL_ACTIVE_LOW (0 << 14)
++#define LTV_HSPL_ACTIVE_HIGH (1 << 14)
++#define LTV_DPL_SAMPLE_RISING (0 << 13)
++#define LTV_DPL_SAMPLE_FALLING (1 << 13)
++#define LTV_EPL_ACTIVE_LOW (0 << 12)
++#define LTV_EPL_ACTIVE_HIGH (1 << 12)
++#define LTV_SS_LEFT_TO_RIGHT (0 << 8)
++#define LTV_SS_RIGHT_TO_LEFT (1 << 8)
++#define LTV_STB (1 << 1)
++
++/* Bit definitions for LTV_GATECTL1 */
++#define LTV_CLW(x) (((x) & 0x0007) << 12)
++#define LTV_GAON (1 << 5)
++#define LTV_SDR (1 << 3)
++
++/* Bit definitions for LTV_GATECTL2 */
++#define LTV_NW_INV_FRAME (0 << 14)
++#define LTV_NW_INV_1LINE (1 << 14)
++#define LTV_NW_INV_2LINE (2 << 14)
++#define LTV_DSC (1 << 12)
++#define LTV_GIF (1 << 8)
++#define LTV_FHN (1 << 7)
++#define LTV_FTI(x) (((x) & 0x0003) << 4)
++#define LTV_FWI(x) (((x) & 0x0003) << 0)
++
++/* Bit definitions for LTV_SOTCTL */
++#define LTV_SDT(x) (((x) & 0x0007) << 10)
++#define LTV_EQ(x) (((x) & 0x0007) << 2)
++
++/* Bit definitions for LTV_PWRCTL1 */
++#define LTV_VCOM_DISABLE (1 << 14)
++#define LTV_VCOMOUT_ENABLE (1 << 11)
++#define LTV_POWER_ON (1 << 9)
++#define LTV_DRIVE_CURRENT(x) (((x) & 0x0007) << 4) /* 0=off, 5=max */
++#define LTV_SUPPLY_CURRENT(x) (((x) & 0x0007) << 0) /* 0=off, 5=max */
++
++/* Bit definitions for LTV_PWRCTL2 */
++#define LTV_VCOML_ENABLE (1 << 13)
++#define LTV_VCOML_VOLTAGE(x) (((x) & 0x001f) << 8) /* 0=1V, 31=-1V */
++#define LTV_VCOMH_VOLTAGE(x) (((x) & 0x001f) << 0) /* 0=3V, 31=4.5V */
++
++#endif /* __LTV350QV_H */
+diff --git a/include/asm-avr32/arch-at32ap/board.h b/include/asm-avr32/arch-at32ap/board.h
+index 0215965..e1318e0 100644
+--- a/include/asm-avr32/arch-at32ap/board.h
++++ b/include/asm-avr32/arch-at32ap/board.h
+@@ -6,6 +6,8 @@
+
+ #include <linux/types.h>
+
++#define GPIO_PIN_NONE (-1)
++
+ /* Add basic devices: system manager, interrupt controller, portmuxes, etc. */
+ void at32_add_system_devices(void);
+
+@@ -31,11 +33,26 @@ struct spi_board_info;
+ struct platform_device *
+ at32_add_device_spi(unsigned int id, struct spi_board_info *b, unsigned int n);
+
++struct platform_device *at32_add_device_twi(unsigned int id);
projects / openwrt.git / blobdiff