+++ /dev/null
-/*
- * Generic Broadcom Home Networking Division (HND) DMA engine HW interface
- * This supports the following chips: BCM42xx, 44xx, 47xx .
- *
- * Copyright 2007, Broadcom Corporation
- * All Rights Reserved.
- *
- * THIS SOFTWARE IS OFFERED "AS IS", AND BROADCOM GRANTS NO WARRANTIES OF ANY
- * KIND, EXPRESS OR IMPLIED, BY STATUTE, COMMUNICATION OR OTHERWISE. BROADCOM
- * SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS
- * FOR A SPECIFIC PURPOSE OR NONINFRINGEMENT CONCERNING THIS SOFTWARE.
- *
- */
-
-#ifndef _sbhnddma_h_
-#define _sbhnddma_h_
-
-/* DMA structure:
- * support two DMA engines: 32 bits address or 64 bit addressing
- * basic DMA register set is per channel(transmit or receive)
- * a pair of channels is defined for convenience
- */
-
-
-/* 32 bits addressing */
-
-/* dma registers per channel(xmt or rcv) */
-typedef volatile struct {
- uint32 control; /* enable, et al */
- uint32 addr; /* descriptor ring base address (4K aligned) */
- uint32 ptr; /* last descriptor posted to chip */
- uint32 status; /* current active descriptor, et al */
-} dma32regs_t;
-
-typedef volatile struct {
- dma32regs_t xmt; /* dma tx channel */
- dma32regs_t rcv; /* dma rx channel */
-} dma32regp_t;
-
-typedef volatile struct { /* diag access */
- uint32 fifoaddr; /* diag address */
- uint32 fifodatalow; /* low 32bits of data */
- uint32 fifodatahigh; /* high 32bits of data */
- uint32 pad; /* reserved */
-} dma32diag_t;
-
-/*
- * DMA Descriptor
- * Descriptors are only read by the hardware, never written back.
- */
-typedef volatile struct {
- uint32 ctrl; /* misc control bits & bufcount */
- uint32 addr; /* data buffer address */
-} dma32dd_t;
-
-/*
- * Each descriptor ring must be 4096byte aligned, and fit within a single 4096byte page.
- */
-#define D32MAXRINGSZ 4096
-#define D32RINGALIGN 4096
-#define D32MAXDD (D32MAXRINGSZ / sizeof (dma32dd_t))
-
-/* transmit channel control */
-#define XC_XE ((uint32)1 << 0) /* transmit enable */
-#define XC_SE ((uint32)1 << 1) /* transmit suspend request */
-#define XC_LE ((uint32)1 << 2) /* loopback enable */
-#define XC_FL ((uint32)1 << 4) /* flush request */
-#define XC_AE ((uint32)3 << 16) /* address extension bits */
-#define XC_AE_SHIFT 16
-
-/* transmit descriptor table pointer */
-#define XP_LD_MASK 0xfff /* last valid descriptor */
-
-/* transmit channel status */
-#define XS_CD_MASK 0x0fff /* current descriptor pointer */
-#define XS_XS_MASK 0xf000 /* transmit state */
-#define XS_XS_SHIFT 12
-#define XS_XS_DISABLED 0x0000 /* disabled */
-#define XS_XS_ACTIVE 0x1000 /* active */
-#define XS_XS_IDLE 0x2000 /* idle wait */
-#define XS_XS_STOPPED 0x3000 /* stopped */
-#define XS_XS_SUSP 0x4000 /* suspend pending */
-#define XS_XE_MASK 0xf0000 /* transmit errors */
-#define XS_XE_SHIFT 16
-#define XS_XE_NOERR 0x00000 /* no error */
-#define XS_XE_DPE 0x10000 /* descriptor protocol error */
-#define XS_XE_DFU 0x20000 /* data fifo underrun */
-#define XS_XE_BEBR 0x30000 /* bus error on buffer read */
-#define XS_XE_BEDA 0x40000 /* bus error on descriptor access */
-#define XS_AD_MASK 0xfff00000 /* active descriptor */
-#define XS_AD_SHIFT 20
-
-/* receive channel control */
-#define RC_RE ((uint32)1 << 0) /* receive enable */
-#define RC_RO_MASK 0xfe /* receive frame offset */
-#define RC_RO_SHIFT 1
-#define RC_FM ((uint32)1 << 8) /* direct fifo receive (pio) mode */
-#define RC_AE ((uint32)3 << 16) /* address extension bits */
-#define RC_AE_SHIFT 16
-
-/* receive descriptor table pointer */
-#define RP_LD_MASK 0xfff /* last valid descriptor */
-
-/* receive channel status */
-#define RS_CD_MASK 0x0fff /* current descriptor pointer */
-#define RS_RS_MASK 0xf000 /* receive state */
-#define RS_RS_SHIFT 12
-#define RS_RS_DISABLED 0x0000 /* disabled */
-#define RS_RS_ACTIVE 0x1000 /* active */
-#define RS_RS_IDLE 0x2000 /* idle wait */
-#define RS_RS_STOPPED 0x3000 /* reserved */
-#define RS_RE_MASK 0xf0000 /* receive errors */
-#define RS_RE_SHIFT 16
-#define RS_RE_NOERR 0x00000 /* no error */
-#define RS_RE_DPE 0x10000 /* descriptor protocol error */
-#define RS_RE_DFO 0x20000 /* data fifo overflow */
-#define RS_RE_BEBW 0x30000 /* bus error on buffer write */
-#define RS_RE_BEDA 0x40000 /* bus error on descriptor access */
-#define RS_AD_MASK 0xfff00000 /* active descriptor */
-#define RS_AD_SHIFT 20
-
-/* fifoaddr */
-#define FA_OFF_MASK 0xffff /* offset */
-#define FA_SEL_MASK 0xf0000 /* select */
-#define FA_SEL_SHIFT 16
-#define FA_SEL_XDD 0x00000 /* transmit dma data */
-#define FA_SEL_XDP 0x10000 /* transmit dma pointers */
-#define FA_SEL_RDD 0x40000 /* receive dma data */
-#define FA_SEL_RDP 0x50000 /* receive dma pointers */
-#define FA_SEL_XFD 0x80000 /* transmit fifo data */
-#define FA_SEL_XFP 0x90000 /* transmit fifo pointers */
-#define FA_SEL_RFD 0xc0000 /* receive fifo data */
-#define FA_SEL_RFP 0xd0000 /* receive fifo pointers */
-#define FA_SEL_RSD 0xe0000 /* receive frame status data */
-#define FA_SEL_RSP 0xf0000 /* receive frame status pointers */
-
-/* descriptor control flags */
-#define CTRL_BC_MASK 0x1fff /* buffer byte count */
-#define CTRL_AE ((uint32)3 << 16) /* address extension bits */
-#define CTRL_AE_SHIFT 16
-#define CTRL_EOT ((uint32)1 << 28) /* end of descriptor table */
-#define CTRL_IOC ((uint32)1 << 29) /* interrupt on completion */
-#define CTRL_EOF ((uint32)1 << 30) /* end of frame */
-#define CTRL_SOF ((uint32)1 << 31) /* start of frame */
-
-/* control flags in the range [27:20] are core-specific and not defined here */
-#define CTRL_CORE_MASK 0x0ff00000
-
-/* 64 bits addressing */
-
-/* dma registers per channel(xmt or rcv) */
-typedef volatile struct {
- uint32 control; /* enable, et al */
- uint32 ptr; /* last descriptor posted to chip */
- uint32 addrlow; /* descriptor ring base address low 32-bits (8K aligned) */
- uint32 addrhigh; /* descriptor ring base address bits 63:32 (8K aligned) */
- uint32 status0; /* current descriptor, xmt state */
- uint32 status1; /* active descriptor, xmt error */
-} dma64regs_t;
-
-typedef volatile struct {
- dma64regs_t tx; /* dma64 tx channel */
- dma64regs_t rx; /* dma64 rx channel */
-} dma64regp_t;
-
-typedef volatile struct { /* diag access */
- uint32 fifoaddr; /* diag address */
- uint32 fifodatalow; /* low 32bits of data */
- uint32 fifodatahigh; /* high 32bits of data */
- uint32 pad; /* reserved */
-} dma64diag_t;
-
-/*
- * DMA Descriptor
- * Descriptors are only read by the hardware, never written back.
- */
-typedef volatile struct {
- uint32 ctrl1; /* misc control bits & bufcount */
- uint32 ctrl2; /* buffer count and address extension */
- uint32 addrlow; /* memory address of the date buffer, bits 31:0 */
- uint32 addrhigh; /* memory address of the date buffer, bits 63:32 */
-} dma64dd_t;
-
-/*
- * Each descriptor ring must be 8kB aligned, and fit within a contiguous 8kB physical addresss.
- */
-#define D64MAXRINGSZ 8192
-#define D64RINGALIGN 8192
-#define D64MAXDD (D64MAXRINGSZ / sizeof (dma64dd_t))
-
-/* transmit channel control */
-#define D64_XC_XE 0x00000001 /* transmit enable */
-#define D64_XC_SE 0x00000002 /* transmit suspend request */
-#define D64_XC_LE 0x00000004 /* loopback enable */
-#define D64_XC_FL 0x00000010 /* flush request */
-#define D64_XC_AE 0x00030000 /* address extension bits */
-#define D64_XC_AE_SHIFT 16
-
-/* transmit descriptor table pointer */
-#define D64_XP_LD_MASK 0x00000fff /* last valid descriptor */
-
-/* transmit channel status */
-#define D64_XS0_CD_MASK 0x00001fff /* current descriptor pointer */
-#define D64_XS0_XS_MASK 0xf0000000 /* transmit state */
-#define D64_XS0_XS_SHIFT 28
-#define D64_XS0_XS_DISABLED 0x00000000 /* disabled */
-#define D64_XS0_XS_ACTIVE 0x10000000 /* active */
-#define D64_XS0_XS_IDLE 0x20000000 /* idle wait */
-#define D64_XS0_XS_STOPPED 0x30000000 /* stopped */
-#define D64_XS0_XS_SUSP 0x40000000 /* suspend pending */
-
-#define D64_XS1_AD_MASK 0x0001ffff /* active descriptor */
-#define D64_XS1_XE_MASK 0xf0000000 /* transmit errors */
-#define D64_XS1_XE_SHIFT 28
-#define D64_XS1_XE_NOERR 0x00000000 /* no error */
-#define D64_XS1_XE_DPE 0x10000000 /* descriptor protocol error */
-#define D64_XS1_XE_DFU 0x20000000 /* data fifo underrun */
-#define D64_XS1_XE_DTE 0x30000000 /* data transfer error */
-#define D64_XS1_XE_DESRE 0x40000000 /* descriptor read error */
-#define D64_XS1_XE_COREE 0x50000000 /* core error */
-
-/* receive channel control */
-#define D64_RC_RE 0x00000001 /* receive enable */
-#define D64_RC_RO_MASK 0x000000fe /* receive frame offset */
-#define D64_RC_RO_SHIFT 1
-#define D64_RC_FM 0x00000100 /* direct fifo receive (pio) mode */
-#define D64_RC_AE 0x00030000 /* address extension bits */
-#define D64_RC_AE_SHIFT 16
-
-/* receive descriptor table pointer */
-#define D64_RP_LD_MASK 0x00000fff /* last valid descriptor */
-
-/* receive channel status */
-#define D64_RS0_CD_MASK 0x00001fff /* current descriptor pointer */
-#define D64_RS0_RS_MASK 0xf0000000 /* receive state */
-#define D64_RS0_RS_SHIFT 28
-#define D64_RS0_RS_DISABLED 0x00000000 /* disabled */
-#define D64_RS0_RS_ACTIVE 0x10000000 /* active */
-#define D64_RS0_RS_IDLE 0x20000000 /* idle wait */
-#define D64_RS0_RS_STOPPED 0x30000000 /* stopped */
-#define D64_RS0_RS_SUSP 0x40000000 /* suspend pending */
-
-#define D64_RS1_AD_MASK 0x0001ffff /* active descriptor */
-#define D64_RS1_RE_MASK 0xf0000000 /* receive errors */
-#define D64_RS1_RE_SHIFT 28
-#define D64_RS1_RE_NOERR 0x00000000 /* no error */
-#define D64_RS1_RE_DPO 0x10000000 /* descriptor protocol error */
-#define D64_RS1_RE_DFU 0x20000000 /* data fifo overflow */
-#define D64_RS1_RE_DTE 0x30000000 /* data transfer error */
-#define D64_RS1_RE_DESRE 0x40000000 /* descriptor read error */
-#define D64_RS1_RE_COREE 0x50000000 /* core error */
-
-/* fifoaddr */
-#define D64_FA_OFF_MASK 0xffff /* offset */
-#define D64_FA_SEL_MASK 0xf0000 /* select */
-#define D64_FA_SEL_SHIFT 16
-#define D64_FA_SEL_XDD 0x00000 /* transmit dma data */
-#define D64_FA_SEL_XDP 0x10000 /* transmit dma pointers */
-#define D64_FA_SEL_RDD 0x40000 /* receive dma data */
-#define D64_FA_SEL_RDP 0x50000 /* receive dma pointers */
-#define D64_FA_SEL_XFD 0x80000 /* transmit fifo data */
-#define D64_FA_SEL_XFP 0x90000 /* transmit fifo pointers */
-#define D64_FA_SEL_RFD 0xc0000 /* receive fifo data */
-#define D64_FA_SEL_RFP 0xd0000 /* receive fifo pointers */
-#define D64_FA_SEL_RSD 0xe0000 /* receive frame status data */
-#define D64_FA_SEL_RSP 0xf0000 /* receive frame status pointers */
-
-/* descriptor control flags 1 */
-#define D64_CTRL1_EOT ((uint32)1 << 28) /* end of descriptor table */
-#define D64_CTRL1_IOC ((uint32)1 << 29) /* interrupt on completion */
-#define D64_CTRL1_EOF ((uint32)1 << 30) /* end of frame */
-#define D64_CTRL1_SOF ((uint32)1 << 31) /* start of frame */
-
-/* descriptor control flags 2 */
-#define D64_CTRL2_BC_MASK 0x00007fff /* buffer byte count mask */
-#define D64_CTRL2_AE 0x00030000 /* address extension bits */
-#define D64_CTRL2_AE_SHIFT 16
-
-/* control flags in the range [27:20] are core-specific and not defined here */
-#define D64_CTRL_CORE_MASK 0x0ff00000
-
-
-#endif /* _sbhnddma_h_ */
projects / openwrt.git / blobdiff