Neue ini

[stratum0-wiki.git] / 3D-Drucker%2FSlicerBundle.ini.mw

diff --git a/3D-Drucker%2FSlicerBundle.ini.mw b/3D-Drucker%2FSlicerBundle.ini.mw
index 8d24789..1bb1a22 100644 (file)
--- a/3D-Drucker%2FSlicerBundle.ini.mw
+++ b/3D-Drucker%2FSlicerBundle.ini.mw
@@ -1,22 +1,22 @@
-# generated by Slic3r 1.2.9 on Fri May 13 17:04:53 2016
+# generated by Slic3r 1.2.9 on Thu May 19 15:50:57 2016
 
-[filament:LULZBOT ABS fine]
-bed_temperature = 100
-bridge_fan_speed = 0
+[filament:Lulzbot PLA Weiß]
+bed_temperature = 50
+bridge_fan_speed = 100
 cooling = 1
 disable_fan_first_layers = 1
 extrusion_multiplier = 1
 fan_always_on = 0
 fan_below_layer_time = 60
 filament_colour = #FFFFFF
-filament_diameter = 2.89
-first_layer_bed_temperature = 100
-first_layer_temperature = 250
-max_fan_speed = 0
-min_fan_speed = 0
-min_print_speed = 15
+filament_diameter = 2.85
+first_layer_bed_temperature = 55
+first_layer_temperature = 200
+max_fan_speed = 100
+min_fan_speed = 30
+min_print_speed = 10
 slowdown_below_layer_time = 20
-temperature = 240
+temperature = 190
 
 [filament:MendelPro ABS]
 bed_temperature = 0
@@ -64,7 +64,7 @@ fan_always_on = 1
 fan_below_layer_time = 60
 filament_colour = #FFFFFF
 filament_diameter = 1.7
-first_layer_bed_temperature = 55
+first_layer_bed_temperature = 50
 first_layer_temperature = 200
 max_fan_speed = 100
 min_fan_speed = 50
@@ -72,6 +72,24 @@ min_print_speed = 5
 slowdown_below_layer_time = 30
 temperature = 180
 
+[filament:MendelPro PLA fast]
+bed_temperature = 50
+bridge_fan_speed = 100
+cooling = 1
+disable_fan_first_layers = 1
+extrusion_multiplier = 1
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_colour = #FFFFFF
+filament_diameter = 1.7
+first_layer_bed_temperature = 50
+first_layer_temperature = 200
+max_fan_speed = 100
+min_fan_speed = 50
+min_print_speed = 5
+slowdown_below_layer_time = 30
+temperature = 100
+
 [filament:TinyBoy PLA]
 bed_temperature = 0
 bridge_fan_speed = 100
@@ -126,7 +144,7 @@ min_print_speed = 5
 slowdown_below_layer_time = 15
 temperature = 250
 
-[filament:prusa i3 PLA rot]
+[filament:prusa i3 PLA lila]
 bed_temperature = 50
 bridge_fan_speed = 100
 cooling = 1
@@ -134,8 +152,8 @@ disable_fan_first_layers = 1
 extrusion_multiplier = 1
 fan_always_on = 1
 fan_below_layer_time = 60
-filament_colour = #FF0000
-filament_diameter = 2.9
+filament_colour = #8000FF
+filament_diameter = 3
 first_layer_bed_temperature = 50
 first_layer_temperature = 200
 max_fan_speed = 100
@@ -145,19 +163,19 @@ slowdown_below_layer_time = 15
 temperature = 200
 
 [presets]
-filament = LULZBOT ABS fine.ini
-print = prusa i3 100.ini
-printer = LULZBOT ABS fine.ini
+filament = MendelPro PLA fast.ini
+print = MendelPro.ini
+printer = MendelPro.ini
 
-[print:LULZBOT ABS fine  ]
+[print:Lulzbot]
 avoid_crossing_perimeters = 1
-bottom_solid_layers = 2
-bridge_acceleration = 1000
-bridge_flow_ratio = 1.1
+bottom_solid_layers = 4
+bridge_acceleration = 0
+bridge_flow_ratio = 1
 bridge_speed = 40
 brim_width = 0
 complete_objects = 0
-default_acceleration = 900
+default_acceleration = 0
 dont_support_bridges = 1
 external_fill_pattern = rectilinear
 external_perimeter_extrusion_width = 0
@@ -166,26 +184,26 @@ external_perimeters_first = 0
 extra_perimeters = 1
 extruder_clearance_height = 20
 extruder_clearance_radius = 20
-extrusion_width = 0.37
+extrusion_width = 0
 fill_angle = 35
 fill_density = 30%
 fill_pattern = line
 first_layer_acceleration = 0
-first_layer_extrusion_width = 0.37
-first_layer_height = 120%
-first_layer_speed = 85%
-gap_fill_speed = 45
+first_layer_extrusion_width = 0
+first_layer_height = 0.2
+first_layer_speed = 10
+gap_fill_speed = 20
 gcode_comments = 0
-infill_acceleration = 1400
+infill_acceleration = 0
 infill_every_layers = 2
 infill_extruder = 1
-infill_extrusion_width = 0.6
+infill_extrusion_width = 0
 infill_first = 0
 infill_only_where_needed = 0
 infill_overlap = 15%
-infill_speed = 70
+infill_speed = 0
 interface_shells = 0
-layer_height = 0.14
+layer_height = 0.25
 max_print_speed = 80
 max_volumetric_speed = 0
 min_skirt_length = 0
@@ -194,11 +212,11 @@ only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base].gcode
 overhangs = 1
-perimeter_acceleration = 900
+perimeter_acceleration = 0
 perimeter_extruder = 1
-perimeter_extrusion_width = 0.34
-perimeter_speed = 40
-perimeters = 4
+perimeter_extrusion_width = 0
+perimeter_speed = 0
+perimeters = 3
 post_process = 
 raft_layers = 0
 resolution = 0
@@ -211,7 +229,7 @@ solid_infill_below_area = 30
 solid_infill_every_layers = 0
 solid_infill_extruder = 1
 solid_infill_extrusion_width = 0
-solid_infill_speed = 60
+solid_infill_speed = 0
 spiral_vase = 0
 standby_temperature_delta = -5
 support_material = 0
@@ -226,14 +244,14 @@ support_material_interface_spacing = 0
 support_material_interface_speed = 100%
 support_material_pattern = rectilinear
 support_material_spacing = 2.5
-support_material_speed = 60
+support_material_speed = 0
 support_material_threshold = 45
 thin_walls = 1
 threads = 2
-top_infill_extrusion_width = 0.35
-top_solid_infill_speed = 80%
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 0
 top_solid_layers = 4
-travel_speed = 80
+travel_speed = 100
 xy_size_compensation = 0
 
 [print:MendelPro]
@@ -241,7 +259,7 @@ avoid_crossing_perimeters = 0
 bottom_solid_layers = 3
 bridge_acceleration = 0
 bridge_flow_ratio = 1
-bridge_speed = 35
+bridge_speed = 40
 brim_width = 0
 complete_objects = 0
 default_acceleration = 0
@@ -258,7 +276,7 @@ fill_angle = 45
 fill_density = 15%
 fill_pattern = rectilinear
 first_layer_acceleration = 0
-first_layer_extrusion_width = 150%
+first_layer_extrusion_width = 0
 first_layer_height = 0.2
 first_layer_speed = 10
 gap_fill_speed = 10
@@ -273,9 +291,9 @@ infill_overlap = 15%
 infill_speed = 0
 interface_shells = 0
 layer_height = 0.2
-max_print_speed = 35
+max_print_speed = 80
 max_volumetric_speed = 0
-min_skirt_length = 1
+min_skirt_length = 2
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
@@ -323,19 +341,19 @@ top_solid_layers = 3
 travel_speed = 100
 xy_size_compensation = 0
 
-[print:TinyBoy]
+[print:MendelPro fast]
 avoid_crossing_perimeters = 0
 bottom_solid_layers = 3
 bridge_acceleration = 0
 bridge_flow_ratio = 1
-bridge_speed = 0
+bridge_speed = 40
 brim_width = 0
 complete_objects = 0
 default_acceleration = 0
 dont_support_bridges = 1
 external_fill_pattern = rectilinear
 external_perimeter_extrusion_width = 0
-external_perimeter_speed = 0
+external_perimeter_speed = 20
 external_perimeters_first = 0
 extra_perimeters = 1
 extruder_clearance_height = 20
@@ -345,10 +363,10 @@ fill_angle = 45
 fill_density = 15%
 fill_pattern = rectilinear
 first_layer_acceleration = 0
-first_layer_extrusion_width = 150%
+first_layer_extrusion_width = 0
 first_layer_height = 0.2
-first_layer_speed = 20
-gap_fill_speed = 0
+first_layer_speed = 10
+gap_fill_speed = 10
 gcode_comments = 0
 infill_acceleration = 0
 infill_every_layers = 1
@@ -359,10 +377,10 @@ infill_only_where_needed = 0
 infill_overlap = 15%
 infill_speed = 0
 interface_shells = 0
-layer_height = 0.2
-max_print_speed = 50
+layer_height = 0.5
+max_print_speed = 80
 max_volumetric_speed = 0
-min_skirt_length = 1
+min_skirt_length = 2
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
@@ -380,7 +398,7 @@ seam_position = aligned
 skirt_distance = 1
 skirt_height = 1
 skirts = 1
-small_perimeter_speed = 0
+small_perimeter_speed = 10
 solid_infill_below_area = 70
 solid_infill_every_layers = 0
 solid_infill_extruder = 1
@@ -405,49 +423,49 @@ support_material_threshold = 40
 thin_walls = 1
 threads = 2
 top_infill_extrusion_width = 0
-top_solid_infill_speed = 0
+top_solid_infill_speed = 20
 top_solid_layers = 3
 travel_speed = 100
 xy_size_compensation = 0
 
-[print:prusa i3 100]
+[print:TinyBoy]
 avoid_crossing_perimeters = 0
 bottom_solid_layers = 3
 bridge_acceleration = 0
 bridge_flow_ratio = 1
-bridge_speed = 40
+bridge_speed = 0
 brim_width = 0
 complete_objects = 0
 default_acceleration = 0
 dont_support_bridges = 1
 external_fill_pattern = rectilinear
 external_perimeter_extrusion_width = 0
-external_perimeter_speed = 10
+external_perimeter_speed = 0
 external_perimeters_first = 0
 extra_perimeters = 1
 extruder_clearance_height = 20
 extruder_clearance_radius = 20
 extrusion_width = 0
 fill_angle = 45
-fill_density = 20%
+fill_density = 15%
 fill_pattern = rectilinear
 first_layer_acceleration = 0
-first_layer_extrusion_width = 0
+first_layer_extrusion_width = 150%
 first_layer_height = 0.2
-first_layer_speed = 10
-gap_fill_speed = 10
+first_layer_speed = 20
+gap_fill_speed = 0
 gcode_comments = 0
 infill_acceleration = 0
 infill_every_layers = 1
 infill_extruder = 1
-infill_extrusion_width = 110%
+infill_extrusion_width = 0
 infill_first = 0
 infill_only_where_needed = 0
 infill_overlap = 15%
 infill_speed = 0
 interface_shells = 0
-layer_height = 0.1
-max_print_speed = 80
+layer_height = 0.2
+max_print_speed = 50
 max_volumetric_speed = 0
 min_skirt_length = 1
 notes = 
@@ -459,15 +477,15 @@ perimeter_acceleration = 0
 perimeter_extruder = 1
 perimeter_extrusion_width = 0
 perimeter_speed = 0
-perimeters = 3
+perimeters = 2
 post_process = 
 raft_layers = 0
 resolution = 0
 seam_position = aligned
-skirt_distance = 6
+skirt_distance = 1
 skirt_height = 1
-skirts = 3
-small_perimeter_speed = 10
+skirts = 1
+small_perimeter_speed = 0
 solid_infill_below_area = 70
 solid_infill_every_layers = 0
 solid_infill_extruder = 1
@@ -492,14 +510,14 @@ support_material_threshold = 40
 thin_walls = 1
 threads = 2
 top_infill_extrusion_width = 0
-top_solid_infill_speed = 10
+top_solid_infill_speed = 0
 top_solid_layers = 3
 travel_speed = 100
 xy_size_compensation = 0
 
-[print:prusa i3 100 testtesttest]
+[print:prusa i3 100]
 avoid_crossing_perimeters = 0
-bottom_solid_layers = 0
+bottom_solid_layers = 3
 bridge_acceleration = 0
 bridge_flow_ratio = 1
 bridge_speed = 40
@@ -516,7 +534,7 @@ extruder_clearance_height = 20
 extruder_clearance_radius = 20
 extrusion_width = 0
 fill_angle = 45
-fill_density = 0%
+fill_density = 20%
 fill_pattern = rectilinear
 first_layer_acceleration = 0
 first_layer_extrusion_width = 0
@@ -546,14 +564,14 @@ perimeter_acceleration = 0
 perimeter_extruder = 1
 perimeter_extrusion_width = 0
 perimeter_speed = 0
-perimeters = 1
+perimeters = 3
 post_process = 
 raft_layers = 0
 resolution = 0
 seam_position = aligned
-skirt_distance = 1
+skirt_distance = 6
 skirt_height = 1
-skirts = 1
+skirts = 3
 small_perimeter_speed = 10
 solid_infill_below_area = 70
 solid_infill_every_layers = 0
@@ -580,7 +598,7 @@ thin_walls = 1
 threads = 2
 top_infill_extrusion_width = 0
 top_solid_infill_speed = 10
-top_solid_layers = 0
+top_solid_layers = 3
 travel_speed = 100
 xy_size_compensation = 0
 
@@ -763,14 +781,14 @@ avoid_crossing_perimeters = 0
 bottom_solid_layers = 3
 bridge_acceleration = 0
 bridge_flow_ratio = 1
-bridge_speed = 40
+bridge_speed = 60
 brim_width = 0
 complete_objects = 0
 default_acceleration = 0
 dont_support_bridges = 1
 external_fill_pattern = rectilinear
 external_perimeter_extrusion_width = 0
-external_perimeter_speed = 10
+external_perimeter_speed = 20
 external_perimeters_first = 0
 extra_perimeters = 1
 extruder_clearance_height = 20
@@ -788,7 +806,7 @@ gcode_comments = 0
 infill_acceleration = 0
 infill_every_layers = 1
 infill_extruder = 1
-infill_extrusion_width = 110%
+infill_extrusion_width = 0
 infill_first = 0
 infill_only_where_needed = 0
 infill_overlap = 15%
@@ -825,13 +843,13 @@ spiral_vase = 0
 standby_temperature_delta = -5
 support_material = 1
 support_material_angle = 0
-support_material_contact_distance = 0.2
+support_material_contact_distance = 0.3
 support_material_enforce_layers = 0
 support_material_extruder = 1
 support_material_extrusion_width = 0
 support_material_interface_extruder = 1
 support_material_interface_layers = 2
-support_material_interface_spacing = 0
+support_material_interface_spacing = 2
 support_material_interface_speed = 100%
 support_material_pattern = rectilinear
 support_material_spacing = 5
@@ -845,7 +863,7 @@ top_solid_layers = 3
 travel_speed = 100
 xy_size_compensation = 0
 
-[printer:LULZBOT ABS fine]
+[printer:Lulzbot]
 bed_shape = 0x0,298x0,298x275,0x275
 before_layer_gcode = 
 end_gcode = M104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200 ;\nG28 X0 ; home X axis\nM84 ; disable motors
@@ -864,7 +882,7 @@ retract_lift = 0
 retract_restart_extra = 0
 retract_restart_extra_toolchange = 0
 retract_speed = 20
-start_gcode = G28 ; home all axes
+start_gcode = G28 ; home all axes\n
 toolchange_gcode = 
 use_firmware_retraction = 0
 use_relative_e_distances = 0
@@ -876,7 +894,7 @@ z_offset = 0
 [printer:MendelPro]
 bed_shape = 0x0,220x0,220x177,0x177
 before_layer_gcode = 
-end_gcode = M104 S0        ; turn off temperature\nM140 S0;\nG28 X0           ; home X axis\nM84               ; disable motors\n
+end_gcode = M104 S0        ; turn off temperature\nM140 S0;\nG28 X0           ; home X axis\nG0 Y177;\nM84               ; disable motors\n
 extruder_offset = 0x0
 gcode_flavor = reprap
 layer_gcode =