-# generated by Slic3r 1.2.9 on Thu Jun 2 16:16:44 2016
+# generated by Slic3r 1.2.9 on Sun Aug 14 14:31:08 2016
[filament:Lulzbot ABS]
bed_temperature = 100
-bridge_fan_speed = 100
-cooling = 0
+bridge_fan_speed = 50
+cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 0
filament_diameter = 2.85
first_layer_bed_temperature = 100
first_layer_temperature = 250
-max_fan_speed = 100
-min_fan_speed = 30
-min_print_speed = 10
+max_fan_speed = 0
+min_fan_speed = 0
+min_print_speed = 5
slowdown_below_layer_time = 20
-temperature = 245
+temperature = 230
[filament:Lulzbot PLA]
bed_temperature = 50
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #FFFFFF
-filament_diameter = 2.85
-first_layer_bed_temperature = 55
+filament_diameter = 2.82
+first_layer_bed_temperature = 50
first_layer_temperature = 200
max_fan_speed = 100
min_fan_speed = 35
-min_print_speed = 10
+min_print_speed = 5
slowdown_below_layer_time = 30
-temperature = 190
+temperature = 200
[filament:Lulzbot PLA Weiß]
bed_temperature = 50
fan_below_layer_time = 60
filament_colour = #FFFFFF
filament_diameter = 2.85
-first_layer_bed_temperature = 55
+first_layer_bed_temperature = 50
first_layer_temperature = 200
max_fan_speed = 100
min_fan_speed = 30
-min_print_speed = 10
-slowdown_below_layer_time = 20
-temperature = 190
+min_print_speed = 5
+slowdown_below_layer_time = 30
+temperature = 180
+
+[filament:Lulzbot PLA black]
+bed_temperature = 50
+bridge_fan_speed = 100
+cooling = 1
+disable_fan_first_layers = 1
+extrusion_multiplier = 1
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_colour = #000000
+filament_diameter = 2.9
+first_layer_bed_temperature = 50
+first_layer_temperature = 200
+max_fan_speed = 100
+min_fan_speed = 35
+min_print_speed = 5
+slowdown_below_layer_time = 30
+temperature = 200
[filament:MendelPro ABS]
bed_temperature = 0
slowdown_below_layer_time = 30
temperature = 185
+[filament:MendelPro Mistery]
+bed_temperature = 80
+bridge_fan_speed = 50
+cooling = 1
+disable_fan_first_layers = 1
+extrusion_multiplier = 1
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_colour = #FFFFFF
+filament_diameter = 1.7
+first_layer_bed_temperature = 80
+first_layer_temperature = 250
+max_fan_speed = 0
+min_fan_speed = 0
+min_print_speed = 10
+slowdown_below_layer_time = 20
+temperature = 200
+
[filament:MendelPro PLA]
bed_temperature = 50
bridge_fan_speed = 100
min_fan_speed = 40
min_print_speed = 5
slowdown_below_layer_time = 30
-temperature = 180
+temperature = 185
[filament:MendelPro PLA fast]
bed_temperature = 50
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #35E1FF
-filament_diameter = 1.7
+filament_diameter = 1.63
first_layer_bed_temperature = 0
first_layer_temperature = 200
-max_fan_speed = 50
+max_fan_speed = 40
min_fan_speed = 35
min_print_speed = 5
slowdown_below_layer_time = 15
-temperature = 185
+temperature = 190
-[filament:Toy]
-bed_temperature = 0
+[filament:prusa i3 ABS grün]
+bed_temperature = 100
+bridge_fan_speed = 70
+cooling = 1
+disable_fan_first_layers = 1
+extrusion_multiplier = 1
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_colour = #80FF00
+filament_diameter = 2.9
+first_layer_bed_temperature = 100
+first_layer_temperature = 255
+max_fan_speed = 0
+min_fan_speed = 0
+min_print_speed = 5
+slowdown_below_layer_time = 15
+temperature = 245
+
+[filament:prusa i3 ABS grün blau]
+bed_temperature = 100
+bridge_fan_speed = 70
+cooling = 1
+disable_fan_first_layers = 1
+extrusion_multiplier = 1
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_colour = #0000A0
+filament_diameter = 2.9
+first_layer_bed_temperature = 100
+first_layer_temperature = 240
+max_fan_speed = 0
+min_fan_speed = 0
+min_print_speed = 5
+slowdown_below_layer_time = 30
+temperature = 235
+
+[filament:prusa i3 ABS schwarz]
+bed_temperature = 100
+bridge_fan_speed = 70
+cooling = 1
+disable_fan_first_layers = 1
+extrusion_multiplier = 1
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_colour = #000000
+filament_diameter = 2.9
+first_layer_bed_temperature = 100
+first_layer_temperature = 260
+max_fan_speed = 0
+min_fan_speed = 0
+min_print_speed = 5
+slowdown_below_layer_time = 15
+temperature = 255
+
+[filament:prusa i3 PLA]
+bed_temperature = 50
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #FFFFFF
-filament_diameter = 1.7
-first_layer_bed_temperature = 0
+filament_diameter = 2.9
+first_layer_bed_temperature = 50
first_layer_temperature = 200
max_fan_speed = 100
-min_fan_speed = 100
+min_fan_speed = 50
min_print_speed = 5
slowdown_below_layer_time = 30
-temperature = 180
+temperature = 190
-[filament:prusa i3 PLA black fine]
+[filament:prusa i3 PLA lila]
bed_temperature = 50
bridge_fan_speed = 100
cooling = 1
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 60
-filament_colour = #FF0000
-filament_diameter = 2.9
+filament_colour = #8000FF
+filament_diameter = 3
first_layer_bed_temperature = 50
first_layer_temperature = 200
max_fan_speed = 100
-min_fan_speed = 100
+min_fan_speed = 35
min_print_speed = 5
slowdown_below_layer_time = 15
temperature = 200
-[filament:prusa i3 PLA lila]
+[filament:prusa i3 PLA pink]
bed_temperature = 50
bridge_fan_speed = 100
cooling = 1
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 60
-filament_colour = #8000FF
-filament_diameter = 3
+filament_colour = #FF00FF
+filament_diameter = 2.83
first_layer_bed_temperature = 50
first_layer_temperature = 200
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 5
slowdown_below_layer_time = 15
-temperature = 200
+temperature = 180
[presets]
-filament = MendelPro PLA fast.ini
-print = Lulzbot fine.ini
+filament = prusa i3 ABS grün blau.ini
+print = Lulzbot fine sup.ini
printer = Lulzbot.ini
[print:Lulzbot fine]
avoid_crossing_perimeters = 1
-bottom_solid_layers = 4
+bottom_solid_layers = 2
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 40
-brim_width = 0
+brim_width = 5
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
-external_perimeter_speed = 30
+external_perimeter_speed = 50%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 35
-fill_density = 30%
-fill_pattern = line
+fill_density = 15%
+fill_pattern = 3dhoneycomb
first_layer_acceleration = 0
first_layer_extrusion_width = 0
first_layer_height = 0.2
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
-infill_every_layers = 2
+infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 110%
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
-infill_speed = 0
+infill_speed = 80
interface_shells = 0
-layer_height = 0.25
-max_print_speed = 100
+layer_height = 0.2
+max_print_speed = 80
max_volumetric_speed = 0
min_skirt_length = 0
notes =
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
-perimeter_speed = 0
+perimeter_speed = 60
perimeters = 3
post_process =
raft_layers = 0
resolution = 0
seam_position = aligned
-skirt_distance = 6
+skirt_distance = 10
skirt_height = 1
-skirts = 2
+skirts = 1
small_perimeter_speed = 20
solid_infill_below_area = 30
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
-solid_infill_speed = 0
+solid_infill_speed = 20
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
-support_material_speed = 0
+support_material_speed = 60
support_material_threshold = 45
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
-top_solid_infill_speed = 30
-top_solid_layers = 4
+top_solid_infill_speed = 20
+top_solid_layers = 3
+travel_speed = 100
+xy_size_compensation = 0
+
+[print:Lulzbot fine sup]
+avoid_crossing_perimeters = 1
+bottom_solid_layers = 2
+bridge_acceleration = 0
+bridge_flow_ratio = 1
+bridge_speed = 40
+brim_width = 3
+complete_objects = 0
+default_acceleration = 0
+dont_support_bridges = 1
+external_fill_pattern = rectilinear
+external_perimeter_extrusion_width = 0
+external_perimeter_speed = 50%
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extrusion_width = 0
+fill_angle = 35
+fill_density = 15%
+fill_pattern = 3dhoneycomb
+first_layer_acceleration = 0
+first_layer_extrusion_width = 0
+first_layer_height = 0.2
+first_layer_speed = 10
+gap_fill_speed = 20
+gcode_comments = 0
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 110%
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap = 15%
+infill_speed = 80
+interface_shells = 0
+layer_height = 0.2
+max_print_speed = 80
+max_volumetric_speed = 0
+min_skirt_length = 0
+notes =
+only_retract_when_crossing_perimeters = 0
+ooze_prevention = 0
+output_filename_format = [input_filename_base].gcode
+overhangs = 1
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 60
+perimeters = 3
+post_process =
+raft_layers = 0
+resolution = 0
+seam_position = aligned
+skirt_distance = 10
+skirt_height = 1
+skirts = 1
+small_perimeter_speed = 20
+solid_infill_below_area = 30
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 0
+solid_infill_speed = 20
+spiral_vase = 0
+standby_temperature_delta = -5
+support_material = 1
+support_material_angle = 0
+support_material_contact_distance = 0.2
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_extruder = 1
+support_material_interface_layers = 3
+support_material_interface_spacing = 0
+support_material_interface_speed = 100%
+support_material_pattern = honeycomb
+support_material_spacing = 2.5
+support_material_speed = 60
+support_material_threshold = 45
+thin_walls = 1
+threads = 2
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 20
+top_solid_layers = 3
travel_speed = 100
xy_size_compensation = 0
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 40
-brim_width = 0
+brim_width = 1
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
extrusion_width = 0
fill_angle = 45
fill_density = 15%
-fill_pattern = rectilinear
+fill_pattern = 3dhoneycomb
first_layer_acceleration = 0
first_layer_extrusion_width = 0
first_layer_height = 0.2
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 5
-support_material_speed = 0
+support_material_speed = 60
support_material_threshold = 40
thin_walls = 1
threads = 2
extrusion_width = 0
fill_angle = 45
fill_density = 15%
-fill_pattern = rectilinear
+fill_pattern = 3dhoneycomb
first_layer_acceleration = 0
first_layer_extrusion_width = 0
first_layer_height = 0.2
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 5
-support_material_speed = 0
+support_material_speed = 60
support_material_threshold = 40
thin_walls = 1
threads = 2
travel_speed = 100
xy_size_compensation = 0
-[print:TinyBoy]
+[print:MendelProSup]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1
-bridge_speed = 0
-brim_width = 0
+bridge_speed = 40
+brim_width = 3
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
-external_perimeter_speed = 0
+external_perimeter_speed = 20
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extrusion_width = 0
fill_angle = 45
fill_density = 15%
-fill_pattern = rectilinear
+fill_pattern = 3dhoneycomb
first_layer_acceleration = 0
-first_layer_extrusion_width = 150%
+first_layer_extrusion_width = 0
first_layer_height = 0.2
-first_layer_speed = 20
-gap_fill_speed = 0
+first_layer_speed = 10
+gap_fill_speed = 10
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_speed = 0
interface_shells = 0
layer_height = 0.2
-max_print_speed = 50
+max_print_speed = 80
max_volumetric_speed = 0
-min_skirt_length = 1
+min_skirt_length = 2
notes =
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
skirt_distance = 1
skirt_height = 1
skirts = 1
-small_perimeter_speed = 0
+small_perimeter_speed = 10
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_speed = 0
spiral_vase = 0
standby_temperature_delta = -5
-support_material = 0
+support_material = 1
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
-support_material_interface_layers = 2
+support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
-support_material_pattern = rectilinear
-support_material_spacing = 5
-support_material_speed = 0
+support_material_pattern = honeycomb
+support_material_spacing = 2.5
+support_material_speed = 60
support_material_threshold = 40
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
-top_solid_infill_speed = 0
+top_solid_infill_speed = 20
top_solid_layers = 3
travel_speed = 100
xy_size_compensation = 0
-[print:Toy]
+[print:TinyBoy]
avoid_crossing_perimeters = 0
-bottom_solid_layers = 2
+bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1
-bridge_speed = 0
+bridge_speed = 40
brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
-external_perimeter_speed = 0
+external_perimeter_speed = 20
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
-fill_density = 0%
-fill_pattern = rectilinear
+fill_density = 20%
+fill_pattern = 3dhoneycomb
first_layer_acceleration = 0
first_layer_extrusion_width = 0
first_layer_height = 0.2
first_layer_speed = 10
-gap_fill_speed = 0
+gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_speed = 0
interface_shells = 0
layer_height = 0.2
-max_print_speed = 10
+max_print_speed = 80
max_volumetric_speed = 0
min_skirt_length = 1
notes =
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
-top_solid_infill_speed = 0
-top_solid_layers = 0
+top_solid_infill_speed = 20
+top_solid_layers = 4
travel_speed = 100
xy_size_compensation = 0
-[print:prusa i3 100]
+[print:TinyBoy sup]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
-external_perimeter_speed = 10
+external_perimeter_speed = 20
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extrusion_width = 0
fill_angle = 45
fill_density = 20%
-fill_pattern = rectilinear
+fill_pattern = 3dhoneycomb
first_layer_acceleration = 0
first_layer_extrusion_width = 0
first_layer_height = 0.2
first_layer_speed = 10
-gap_fill_speed = 10
+gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
-infill_extrusion_width = 110%
+infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 0
interface_shells = 0
-layer_height = 0.1
+layer_height = 0.2
max_print_speed = 80
max_volumetric_speed = 0
min_skirt_length = 1
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 0
-perimeters = 3
+perimeters = 2
post_process =
raft_layers = 0
resolution = 0
seam_position = aligned
-skirt_distance = 6
+skirt_distance = 1
skirt_height = 1
-skirts = 3
-small_perimeter_speed = 10
+skirts = 1
+small_perimeter_speed = 0
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_speed = 0
spiral_vase = 0
standby_temperature_delta = -5
-support_material = 0
+support_material = 1
support_material_angle = 0
-support_material_contact_distance = 0.2
+support_material_contact_distance = 0.3
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
-top_solid_infill_speed = 10
-top_solid_layers = 3
+top_solid_infill_speed = 20
+top_solid_layers = 4
travel_speed = 100
xy_size_compensation = 0
-[print:prusa i3 250]
+[print:Toy]
avoid_crossing_perimeters = 0
-bottom_solid_layers = 3
+bottom_solid_layers = 2
bridge_acceleration = 0
bridge_flow_ratio = 1
-bridge_speed = 40
+bridge_speed = 0
brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
-external_perimeter_speed = 10
+external_perimeter_speed = 0
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
-fill_density = 20%
+fill_density = 0%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 0
first_layer_height = 0.2
-first_layer_speed = 15
-gap_fill_speed = 10
+first_layer_speed = 10
+gap_fill_speed = 0
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
-infill_extrusion_width = 110%
+infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 0
interface_shells = 0
-layer_height = 0.25
-max_print_speed = 60
+layer_height = 0.2
+max_print_speed = 10
max_volumetric_speed = 0
min_skirt_length = 1
notes =
skirt_distance = 1
skirt_height = 1
skirts = 1
-small_perimeter_speed = 10
+small_perimeter_speed = 0
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_speed = 0
spiral_vase = 0
standby_temperature_delta = -5
-support_material = 0
+support_material = 1
support_material_angle = 0
-support_material_contact_distance = 0.2
+support_material_contact_distance = 0.3
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
-support_material_interface_layers = 2
+support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
-top_solid_infill_speed = 20
-top_solid_layers = 3
+top_solid_infill_speed = 0
+top_solid_layers = 0
travel_speed = 100
xy_size_compensation = 0
-[print:prusa i3 400]
+[print:prusa i3 200]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1
-bridge_speed = 60
-brim_width = 0
+bridge_speed = 40
+brim_width = 5
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
extrusion_width = 0
fill_angle = 45
fill_density = 20%
-fill_pattern = rectilinear
+fill_pattern = 3dhoneycomb
first_layer_acceleration = 0
first_layer_extrusion_width = 0
first_layer_height = 0.2
-first_layer_speed = 10
-gap_fill_speed = 10
+first_layer_speed = 15
+gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
-infill_extrusion_width = 110%
+infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 0
interface_shells = 0
-layer_height = 0.4
-max_print_speed = 80
+layer_height = 0.2
+max_print_speed = 60
max_volumetric_speed = 0
min_skirt_length = 1
notes =
skirt_distance = 1
skirt_height = 1
skirts = 1
-small_perimeter_speed = 10
+small_perimeter_speed = 15
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
-support_material_contact_distance = 0.2
+support_material_contact_distance = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 2
support_material_interface_spacing = 0
-support_material_interface_speed = 100%
-support_material_pattern = rectilinear
-support_material_spacing = 5
-support_material_speed = 0
+support_material_interface_speed = 10
+support_material_pattern = pillars
+support_material_spacing = 2.5
+support_material_speed = 40
support_material_threshold = 40
thin_walls = 1
threads = 2
travel_speed = 100
xy_size_compensation = 0
-[print:prusa i3 400 sup]
+[print:prusa i3 200 sup]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1
-bridge_speed = 60
-brim_width = 0
+bridge_speed = 40
+brim_width = 5
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
extrusion_width = 0
fill_angle = 45
fill_density = 20%
-fill_pattern = rectilinear
+fill_pattern = 3dhoneycomb
first_layer_acceleration = 0
first_layer_extrusion_width = 0
first_layer_height = 0.2
-first_layer_speed = 10
-gap_fill_speed = 10
+first_layer_speed = 15
+gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_overlap = 15%
infill_speed = 0
interface_shells = 0
-layer_height = 0.4
-max_print_speed = 80
+layer_height = 0.2
+max_print_speed = 60
max_volumetric_speed = 0
min_skirt_length = 1
notes =
perimeter_speed = 0
perimeters = 2
post_process =
-raft_layers = 0
+raft_layers = 1
resolution = 0
seam_position = aligned
skirt_distance = 1
skirt_height = 1
skirts = 1
-small_perimeter_speed = 10
+small_perimeter_speed = 15
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
standby_temperature_delta = -5
support_material = 1
support_material_angle = 0
-support_material_contact_distance = 0.3
+support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
-support_material_extrusion_width = 90%
+support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 2
-support_material_interface_spacing = 2
-support_material_interface_speed = 100%
-support_material_pattern = rectilinear
-support_material_spacing = 5
-support_material_speed = 0
+support_material_interface_spacing = 0
+support_material_interface_speed = 10
+support_material_pattern = pillars
+support_material_spacing = 2.5
+support_material_speed = 40
support_material_threshold = 40
thin_walls = 1
threads = 2
pressure_advance = 0
retract_before_travel = 2
retract_layer_change = 1
-retract_length = 1.75
+retract_length = 2
retract_length_toolchange = 3
retract_lift = 0
retract_restart_extra = 0
[printer:prusa i3]
bed_shape = 0x0,190x0,190x190,0x190
before_layer_gcode =
-end_gcode = M104 S0 ; turn off temperature\nM140 S0 ; turn off bed temp \nG28 X0 ; home X axis\nG0 Y190 ; präsent object\nM84 ; disable motors\n\n
+end_gcode = M104 S0 ; turn off temperature\nM140 S0 ; turn off bed temp \nG28 X0 ; home X axis\nG0 Y190 ; präsent object\nM84 ; disable motors\nM81 ; Power off\n\n
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode =
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
-start_gcode = G28 Z ; home Z\n\nG28 X Y ; home X Y\n
-toolchange_gcode =
+start_gcode = G28 Z ; home Z\nG0 Z1 ; lift Z\nG28 X Y ; home X Y\nG0 Y40 ; clab move
+toolchange_gcode = M83 ; turn on relative movement for extruder \nG1 E-5 ; retract filament 5mm \nG1 X10 Y10 Z4.000000 ; home X and Y axis leave Z at current height \nM84 E ; release extruder stepper motor from 'holding' position \n@pause ; pause print! \nG1 E0 ; reset extruder, ready to push out plastic again \nM82 ; set extruder movement back to absolute ready for next layer
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
projects / stratum0-wiki.git / blobdiff