X-Git-Url: http://git.rohieb.name/stratum0-wiki.git/blobdiff_plain/c973360f7c4c6e542d8146a9bd1bd21e68c7e69a..82add5062aab117503f5d8213467e4bbcbd90c71:/RepRap%2FConfigs%2FSlic3r.mw diff --git a/RepRap%2FConfigs%2FSlic3r.mw b/RepRap%2FConfigs%2FSlic3r.mw index 12eba48ee..092067915 100644 --- a/RepRap%2FConfigs%2FSlic3r.mw +++ b/RepRap%2FConfigs%2FSlic3r.mw @@ -1,767 +1 @@ -Eine Seite um (gute) Beispielkonfigkurationen zu sammeln, am besten mit Beispieldruck (Foto) - -Es gibt vermutlich nicht ''die eine Ideal-Konfiguration'' die für alle Teile gut funktioniert, mit den hier gelisteten sollte aber ein Druck einigermaÃen gelingen. - -=== aktuelle configs === -Der Drucker hat sich verändert, dementsprechend haben sich auch die configs geändert. -Beispielsweise haben wir jetzt 0.5 mm Düsen an den beiden Hot Ends, nicht mehr 0.35 mm. -Dazu kommt, dass das homing konstruktionsbedingt auÃerhalb des hot beds stattfindet, mit diesem Start-gcode wird das ausgeglichen: - G28 X0 Y0 ; home X and Y - G0 X60; move to X60 - G92 X0; set postition to X=0 - G28 Z0; home Z -Das, oder etwas Ãhnliches sollte in allen configs mit drin sein. - -Eine funktionierende, aber noch nicht sehr fein justierte config ist diese: -==== larsan ==== -
-# generated by Slic3r 0.9.10 on Sun Sep 29 22:51:39 2013 -avoid_crossing_perimeters = 0 -bed_size = 190,190 -bed_temperature = 50 -bottom_solid_layers = 3 -bridge_acceleration = 0 -bridge_fan_speed = 100 -bridge_flow_ratio = 1 -bridge_speed = 60 -brim_width = 0 -complete_objects = 1 -cooling = 1 -default_acceleration = 0 -disable_fan_first_layers = 1 -duplicate = 1 -duplicate_distance = 6 -duplicate_grid = 1,1 -end_gcode = M104 S0 ; turn off extruder temperature\n;M140 S0 ; turn off bed temperature; currently disabled\nG0 X0 ; move X axis to 0\nG92 Z0 E5 ;define current point as Z0 E5\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y198 F6000 ; drive print table all the way out\nM84 ; disable motors -external_perimeter_speed = 70% -external_perimeters_first = 0 -extra_perimeters = 1 -extruder_clearance_height = 1 -extruder_clearance_radius = 30 -extruder_offset = 0x0 -extrusion_axis = E -extrusion_multiplier = 1 -extrusion_width = 180% -fan_always_on = 0 -fan_below_layer_time = 60 -filament_diameter = 1.75 -fill_angle = 45 -fill_density = 0.3 -fill_pattern = honeycomb -first_layer_bed_temperature = 50 -first_layer_extrusion_width = 0 -first_layer_height = 0.25 -first_layer_speed = 30% -first_layer_temperature = 200 -g0 = 0 -gap_fill_speed = 15 -gcode_arcs = 0 -gcode_comments = 0 -gcode_flavor = reprap -infill_acceleration = 0 -infill_every_layers = 1 -infill_extruder = 1 -infill_extrusion_width = 0 -infill_first = 0 -infill_only_where_needed = 0 -infill_speed = 60 -layer_gcode = -layer_height = 0.25 -max_fan_speed = 100 -min_fan_speed = 35 -min_print_speed = 5 -min_skirt_length = 0 -notes = larsanconfig -nozzle_diameter = 0.5 -only_retract_when_crossing_perimeters = 1 -output_filename_format = [input_filename_base].gcode -perimeter_acceleration = 0 -perimeter_extruder = 1 -perimeter_extrusion_width = 0 -perimeter_speed = 80 -perimeters = 3 -post_process = -print_center = 90,60 -raft_layers = 0 -randomize_start = 0 -resolution = 0 -retract_before_travel = 2 -retract_layer_change = 1 -retract_length = 2 -retract_length_toolchange = 10 -retract_lift = 0 -retract_restart_extra = 0 -retract_restart_extra_toolchange = 0 -retract_speed = 35 -rotate = 0 -scale = 1 -skirt_distance = 10 -skirt_height = 1 -skirts = 3 -slowdown_below_layer_time = 30 -small_perimeter_speed = 50 -solid_fill_pattern = rectilinear -solid_infill_below_area = 40 -solid_infill_every_layers = 0 -solid_infill_extrusion_width = 0 -solid_infill_speed = 80 -spiral_vase = 0 -start_gcode = G28 X0 Y0 ; home X and Y\nG0 X60; move to X60\nG92 X0; set postition to X=0\nG28 Z0; home Z -support_material = 0 -support_material_angle = 0 -support_material_enforce_layers = 0 -support_material_extruder = 1 -support_material_extrusion_width = 0 -support_material_interface_layers = 0 -support_material_interface_spacing = 0 -support_material_pattern = rectilinear -support_material_spacing = 2.5 -support_material_speed = 65 -support_material_threshold = 0 -temperature = 195 -threads = 1 -toolchange_gcode = -top_infill_extrusion_width = 0 -top_solid_infill_speed = 60 -top_solid_layers = 3 -travel_speed = 80 -use_relative_e_distances = 0 -vibration_limit = 0 -wipe = 0 -z_offset = 0 --=== alte configs === - -==== Von larsan ==== -Ursprünglich die erste Konfiguration für unseren Drucker auf Basis von {{Benutzer|DanielWillmann}}s Konfiguration. - -Von der unten stehenden Config gibt es eine verbesserte [https://rohieb.name/stuff/stratum0/larsan-tuned.ini larsan-tuned.ini], die Rohieb gemacht hat. - -
-# generated by Slic3r 0.9.8-dev on Wed Nov 28 08:03:30 2012 -acceleration = 0 -bed_size = 180,200 -bed_temperature = 50 -bottom_solid_layers = 3 -bridge_fan_speed = 100 -bridge_flow_ratio = 1 -bridge_speed = 60 -brim_width = 0 -complete_objects = -cooling = -disable_fan_first_layers = 1 -duplicate = 1 -duplicate_distance = 6 -duplicate_grid = 1,1 -end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors -external_perimeter_speed = 40% -extra_perimeters = 1 -extruder_clearance_height = 20 -extruder_clearance_radius = 30 -extruder_offset = 0x0 -extrusion_axis = E -extrusion_multiplier = 1 -extrusion_width = 0 -fan_always_on = 0 -fan_below_layer_time = 60 -filament_diameter = 1.75 -fill_angle = 0 -fill_density = 0.15 -fill_pattern = honeycomb -first_layer_bed_temperature = 50 -first_layer_extrusion_width = 0 -first_layer_height = 0.27 -first_layer_speed = 15% -first_layer_temperature = 195 -g0 = 0 -gap_fill_speed = 20 -gcode_arcs = 0 -gcode_comments = 0 -gcode_flavor = reprap -infill_acceleration = 50 -infill_every_layers = 1 -infill_extruder = 1 -infill_extrusion_width = 0 -infill_speed = 60 -layer_gcode = -layer_height = 0.24 -max_fan_speed = 100 -min_fan_speed = 35 -min_print_speed = 5 -min_skirt_length = 0 -notes = larsanconfig -nozzle_diameter = 0.35 -only_retract_when_crossing_perimeters = -output_filename_format = [input_filename_base].gcode -perimeter_acceleration = 25 -perimeter_extruder = 1 -perimeter_extrusion_width = 0 -perimeter_speed = 50 -perimeters = 3 -post_process = -print_center = 90,100 -randomize_start = 1 -retract_before_travel = 5 -retract_length = 2 -retract_length_toolchange = 3 -retract_lift = 0 -retract_restart_extra = 0.01 -retract_restart_extra_toolchange = 0 -retract_speed = 50 -rotate = 0 -scale = 1 -skirt_distance = 20 -skirt_height = 1 -skirts = 3 -slowdown_below_layer_time = 50 -small_perimeter_speed = 100% -solid_fill_pattern = rectilinear -solid_infill_below_area = 0 -solid_infill_every_layers = 0 -solid_infill_speed = 90% -start_gcode = G28 ; home all axes\nM92 E820 -support_material = -support_material_angle = 45 -support_material_extruder = 1 -support_material_extrusion_width = 0 -support_material_pattern = rectilinear -support_material_spacing = 2 -support_material_speed = 60 -support_material_threshold = 41 -temperature = 185 -threads = 2 -top_solid_infill_speed = 70% -top_solid_layers = 3 -travel_speed = 50 -use_relative_e_distances = 0 -vibration_limit = 0 -z_offset = 0 -- -==== Schnelle Config von [[Benutzer:Daniel Bohrer|Daniel Bohrer]] (Work in Progress) ==== -Der erste und letzte Layer wird "normal schnell" gedruckt, die anderen doppelt so schnell. Bei dünnen Strukturen (z.B. Mate-Tags) muss man notfalls noch ein bisschen mit der Perimeteranzahl spielen. -
-# generated by Slic3r 0.9.4-dev on Fri Nov 16 20:55:02 2012 -acceleration = 0 -bed_size = 180,200 -bed_temperature = 60 -bridge_fan_speed = 100 -bridge_flow_ratio = 1 -bridge_speed = 350 -brim_width = 0 -complete_objects = 0 -cooling = 1 -disable_fan_first_layers = 1 -duplicate = 1 -duplicate_distance = 6 -duplicate_grid = 1,1 -end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors -external_perimeter_speed = 90% -extra_perimeters = 1 -extruder_clearance_height = 20 -extruder_clearance_radius = 20 -extruder_offset = 0x0 -extrusion_axis = E -extrusion_multiplier = 1.0 -extrusion_width = 0 -fan_always_on = 0 -fan_below_layer_time = 60 -filament_diameter = 1.75 -fill_angle = 0 -fill_density = 0.2 -fill_pattern = rectilinear -first_layer_bed_temperature = 60 -first_layer_extrusion_width = 0 -first_layer_height = 100% -first_layer_speed = 20% -first_layer_temperature = 195 -g0 = 0 -gcode_arcs = 0 -gcode_comments = 0 -gcode_flavor = reprap -infill_acceleration = 50 -infill_every_layers = 1 -infill_extruder = 1 -infill_extrusion_width = 0 -infill_speed = 120 -layer_gcode = -layer_height = 0.25 -max_fan_speed = 100 -min_fan_speed = 35 -min_print_speed = 10 -notes = Used for Mate name tag -nozzle_diameter = 0.35 -only_retract_when_crossing_perimeters = 0 -output_filename_format = [input_filename_base].gcode -perimeter_acceleration = 25 -perimeter_extruder = 1 -perimeter_extrusion_width = 0 -perimeter_speed = 100 -perimeters = 2 -post_process = -print_center = 90,100 -randomize_start = 1 -retract_before_travel = 4 -retract_length = 4 -retract_length_toolchange = 3 -retract_lift = 0.5 -retract_restart_extra = 0 -retract_restart_extra_toolchange = 0 -retract_speed = 150 -rotate = 0 -scale = 1 -skirt_distance = 10 -skirt_height = 1 -skirts = 2 -slowdown_below_layer_time = 60 -small_perimeter_speed = 80% -solid_fill_pattern = rectilinear -solid_infill_below_area = 0 -solid_infill_every_layers = 0 -solid_infill_speed = 100% -solid_layers = 3 -start_gcode = G28 ; home all axes\nM92 E820 -support_material = 1 -support_material_angle = 45 -support_material_extruder = 1 -support_material_extrusion_width = 0 -support_material_pattern = rectilinear -support_material_spacing = 3 -support_material_threshold = 45 -temperature = 185 -threads = 3 -top_solid_infill_speed = 50% -travel_speed = 140 -use_relative_e_distances = 0 -z_offset = 0.22 -- -==== Für Mate-Tags ==== -Konfiguration für Mate-Tags -
-# generated by Slic3r 0.9.9-dev on Fri Jun 7 23:59:05 2013 -avoid_crossing_perimeters = 1 -bed_size = 180,200 -bed_temperature = 50 -bottom_solid_layers = 3 -bridge_acceleration = 0 -bridge_fan_speed = 100 -bridge_flow_ratio = 1 -bridge_speed = 50 -brim_width = 0 -complete_objects = 1 -cooling = -default_acceleration = 0 -disable_fan_first_layers = 1 -duplicate = 1 -duplicate_distance = 6 -duplicate_grid = 1,1 -end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors -external_perimeter_speed = 50% -external_perimeters_first = 0 -extra_perimeters = -extruder_clearance_height = 36 -extruder_clearance_radius = 40 -extruder_offset = 0x0 -extrusion_axis = E -extrusion_multiplier = 1.1 -extrusion_width = 0 -fan_always_on = 0 -fan_below_layer_time = 60 -filament_diameter = 1.75 -fill_angle = 30 -fill_density = 0.3 -fill_pattern = rectilinear -first_layer_bed_temperature = 50 -first_layer_extrusion_width = 0 -first_layer_height = 0.27 -first_layer_speed = 40% -first_layer_temperature = 197 -g0 = 0 -gap_fill_speed = 20 -gcode_arcs = 0 -gcode_comments = 0 -gcode_flavor = reprap -infill_acceleration = 0 -infill_every_layers = 1 -infill_extruder = 1 -infill_extrusion_width = 0 -infill_first = 0 -infill_only_where_needed = 0 -infill_speed = 70 -layer_gcode = -layer_height = 0.24 -max_fan_speed = 100 -min_fan_speed = 35 -min_print_speed = 5 -min_skirt_length = 10 -notes = Config used for bottle name tags (http://www.thingiverse.com/thing:38861) -nozzle_diameter = 0.33 -only_retract_when_crossing_perimeters = 1 -output_filename_format = [input_filename_base].gcode -perimeter_acceleration = 0 -perimeter_extruder = 1 -perimeter_extrusion_width = 0 -perimeter_speed = 50 -perimeters = 2 -post_process = -print_center = 90,100 -raft_layers = 0 -randomize_start = -resolution = 0 -retract_before_travel = 0 -retract_layer_change = 1 -retract_length = 2 -retract_length_toolchange = 5 -retract_lift = 0 -retract_restart_extra = 0 -retract_restart_extra_toolchange = 0 -retract_speed = 50 -rotate = 0 -scale = 1 -skirt_distance = 5 -skirt_height = 1 -skirts = 2 -slowdown_below_layer_time = 50 -small_perimeter_speed = 60% -solid_fill_pattern = rectilinear -solid_infill_below_area = 0 -solid_infill_every_layers = 0 -solid_infill_extrusion_width = 0 -solid_infill_speed = 100% -start_gcode = G28 ; home all axes\nM92 E820 -support_material = -support_material_angle = 45 -support_material_enforce_layers = 0 -support_material_extruder = 1 -support_material_extrusion_width = 0 -support_material_interface_layers = 0 -support_material_interface_spacing = 0 -support_material_pattern = rectilinear -support_material_spacing = 2 -support_material_speed = 70 -support_material_threshold = 41 -temperature = 188 -threads = 2 -toolchange_gcode = -top_infill_extrusion_width = 0 -top_solid_infill_speed = 70% -top_solid_layers = 3 -travel_speed = 50 -use_relative_e_distances = 0 -vibration_limit = 0 -z_offset = 0 -- -==== von Chrissi^ ==== -* Nette Konfiguration zum Drucken von allem möglichen. -* First Layer ist super langsam => Guter Druck auch bei kleinen Strukturen -* First Layer Extrusion Width 110% => Wenig ''Wellenschlagen'' auf dem ersten Layer -
-# generated by Slic3r 0.9.3 on Tue Nov 6 21:53:43 2012 -acceleration = 0 -bed_size = 180,200 -bed_temperature = 60 -bridge_fan_speed = 100 -bridge_flow_ratio = 1.05 -bridge_speed = 60 -brim_width = 0 -complete_objects = -cooling = 1 -disable_fan_first_layers = 1 -duplicate = 1 -duplicate_distance = 6 -duplicate_grid = 1,1 -end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors -external_perimeter_speed = 100% -extra_perimeters = 1 -extruder_clearance_height = 20 -extruder_clearance_radius = 30 -extruder_offset = 0x0 -extrusion_axis = E -extrusion_multiplier = 1 -extrusion_width = 100% -fan_always_on = 0 -fan_below_layer_time = 60 -filament_diameter = 1.75 -fill_angle = 45 -fill_density = 0.1 -fill_pattern = rectilinear -first_layer_bed_temperature = 60 -first_layer_extrusion_width = 112% -first_layer_height = 95% -first_layer_speed = 15% -first_layer_temperature = 200 -g0 = 0 -gcode_arcs = 0 -gcode_comments = 0 -gcode_flavor = reprap -infill_acceleration = 50 -infill_every_layers = 1 -infill_extruder = 1 -infill_extrusion_width = 120% -infill_speed = 60 -layer_gcode = -layer_height = 0.3 -max_fan_speed = 100 -min_fan_speed = 35 -min_print_speed = 5 -notes = larsanconfig -nozzle_diameter = 0.35 -only_retract_when_crossing_perimeters = 1 -output_filename_format = [timestamp]_[input_filename_base].gcode -perimeter_acceleration = 25 -perimeter_extruder = 1 -perimeter_extrusion_width = 0 -perimeter_speed = 60 -perimeters = 2 -post_process = -print_center = 120,120 -randomize_start = 1 -retract_before_travel = 4 -retract_length = 2 -retract_length_toolchange = 3 -retract_lift = 0 -retract_restart_extra = 0 -retract_restart_extra_toolchange = 0 -retract_speed = 50 -rotate = 0 -scale = 1 -skirt_distance = 10 -skirt_height = 1 -skirts = 3 -slowdown_below_layer_time = 50 -small_perimeter_speed = 50% -solid_fill_pattern = rectilinear -solid_infill_below_area = 0 -solid_infill_every_layers = 0 -solid_infill_speed = 100% -solid_layers = 3 -start_gcode = G28 ; home all axes\nM92 E820 -support_material = 1 -support_material_angle = 45 -support_material_extruder = 1 -support_material_extrusion_width = 160% -support_material_pattern = rectilinear -support_material_spacing = 2 -support_material_threshold = 40 -temperature = 205 -threads = 2 -top_solid_infill_speed = 40% -travel_speed = 90 -use_relative_e_distances = 0 -z_offset = 0 -- -==== Gelbes Filament ==== -* Ursprünglich für [[Reprap/Parent]] erstellt -* Damit gedruckt: der letzte gelbe frame-vertex für den Drucker -* etwas wärmer (195°C) -* 0.22 mm z-offeset -
-acceleration = 0 -bed_size = 170,170 -bed_temperature = 60 -bridge_fan_speed = 100 -bridge_flow_ratio = 1 -bridge_speed = 30 -brim_width = 0 -complete_objects = 0 -cooling = 1 -disable_fan_first_layers = 1 -duplicate = 1 -duplicate_distance = 6 -duplicate_grid = 1,1 -end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors -external_perimeter_speed = 90% -extra_perimeters = 1 -extruder_clearance_height = 20 -extruder_clearance_radius = 20 -extrusion_axis = E -extrusion_multiplier = 1 -extrusion_width = 0 -fan_always_on = 0 -fan_below_layer_time = 60 -filament_diameter = 3 -fill_angle = 45 -fill_density = 0.15 -fill_pattern = rectilinear -first_layer_bed_temperature = 60 -first_layer_extrusion_width = 0 -first_layer_height = 115% -first_layer_speed = 80% -first_layer_temperature = 200 -g0 = 0 -gcode_arcs = 0 -gcode_comments = 0 -gcode_flavor = reprap -infill_acceleration = 50 -infill_every_layers = 1 -infill_extruder = 1 -infill_extrusion_width = 0 -infill_speed = 40 -layer_gcode = -layer_height = 0.28 -max_fan_speed = 100 -min_fan_speed = 35 -min_print_speed = 10 -notes = Used for Mate name tag -nozzle_diameter = 0.35 -output_filename_format = [input_filename_base].gcode -perimeter_acceleration = 25 -perimeter_speed = 30 -perimeters = 3 -perimeters_extruder = 1 -perimeters_extrusion_width = 0 -post_process = -print_center = 50,27 -randomize_start = 1 -retract_before_travel = 4 -retract_length = 3 -retract_lift = 0.4 -retract_restart_extra = 0 -retract_speed = 30 -rotate = 0 -scale = 1 -skirt_distance = 6 -skirt_height = 1 -skirts = 3 -slowdown_below_layer_time = 60 -small_perimeter_speed = 30 -solid_fill_pattern = rectilinear -solid_infill_speed = 40 -solid_layers = 3 -start_gcode = G28 ; home all axes\nM92 E820 -support_material = -support_material_angle = 45 -support_material_extruder = 1 -support_material_extrusion_width = 0 -support_material_pattern = rectilinear -support_material_spacing = 2.5 -support_material_threshold = 45 -temperature = 195 -threads = 2 -top_solid_infill_speed = 40 -travel_speed = 130 -use_relative_e_distances = 0 -z_offset = 0.22 -- -==== RepRap-Config ==== -Konfiguration, mit der die Teile für den RepRap vom [http://netz39.eu Netz39] gedruckt wurden. -
-# generated by Slic3r 0.9.9-dev on Mon Jun 3 17:06:48 2013 -avoid_crossing_perimeters = 0 -bed_size = 180,200 -bed_temperature = 50 -bottom_solid_layers = 5 -bridge_acceleration = 0 -bridge_fan_speed = 100 -bridge_flow_ratio = 1 -bridge_speed = 30 -brim_width = 0 -complete_objects = 1 -cooling = -default_acceleration = 0 -disable_fan_first_layers = 1 -duplicate = 1 -duplicate_distance = 6 -duplicate_grid = 1,1 -end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors -external_perimeter_speed = 40% -external_perimeters_first = 0 -extra_perimeters = -extruder_clearance_height = 35 -extruder_clearance_radius = 62 -extruder_offset = 0x0 -extrusion_axis = E -extrusion_multiplier = 1.1 -extrusion_width = 0 -fan_always_on = 0 -fan_below_layer_time = 60 -filament_diameter = 1.75 -fill_angle = 30 -fill_density = 0.5 -fill_pattern = rectilinear -first_layer_bed_temperature = 50 -first_layer_extrusion_width = 0 -first_layer_height = 150% -first_layer_speed = 40% -first_layer_temperature = 197 -g0 = 0 -gap_fill_speed = 20 -gcode_arcs = 0 -gcode_comments = 0 -gcode_flavor = reprap -infill_acceleration = 0 -infill_every_layers = 1 -infill_extruder = 1 -infill_extrusion_width = 0 -infill_first = 0 -infill_only_where_needed = 0 -infill_speed = 60 -layer_gcode = -layer_height = 0.2 -max_fan_speed = 100 -min_fan_speed = 35 -min_print_speed = 5 -min_skirt_length = 15 -notes = config for printing netz39 pieces -nozzle_diameter = 0.33 -only_retract_when_crossing_perimeters = 1 -output_filename_format = [input_filename_base].gcode -perimeter_acceleration = 0 -perimeter_extruder = 1 -perimeter_extrusion_width = 0 -perimeter_speed = 60 -perimeters = 3 -post_process = -print_center = 90,100 -raft_layers = 0 -randomize_start = -resolution = 0 -retract_before_travel = 0 -retract_layer_change = 1 -retract_length = 2 -retract_length_toolchange = 5 -retract_lift = 0 -retract_restart_extra = 0 -retract_restart_extra_toolchange = 0 -retract_speed = 50 -rotate = 0 -scale = 1 -skirt_distance = 5 -skirt_height = 1 -skirts = 2 -slowdown_below_layer_time = 50 -small_perimeter_speed = 60% -solid_fill_pattern = rectilinear -solid_infill_below_area = 0 -solid_infill_every_layers = 0 -solid_infill_extrusion_width = 0 -solid_infill_speed = 100% -start_gcode = G28 ; home all axes\nM92 E820 -support_material = -support_material_angle = 45 -support_material_enforce_layers = 0 -support_material_extruder = 1 -support_material_extrusion_width = 0 -support_material_interface_layers = 0 -support_material_interface_spacing = 0 -support_material_pattern = rectilinear -support_material_spacing = 2 -support_material_speed = 60 -support_material_threshold = 41 -temperature = 188 -threads = 2 -toolchange_gcode = -top_infill_extrusion_width = 0 -top_solid_infill_speed = 70% -top_solid_layers = 5 -travel_speed = 100 -use_relative_e_distances = 0 -vibration_limit = 0 -z_offset = 0 -- -[[Kategorie:RepRap]] +#redirect [[3D-Drucker#Slic3r-Einstellungen]]