projectconfig.h

   1 /**************************************************************************/
   2 /*!
   3     @file     projectconfig.h
   4     @author   K. Townsend (microBuilder.eu)
   5
   6     @section LICENSE
   7
   8     Software License Agreement (BSD License)
   9
  10     Copyright (c) 2012, microBuilder SARL
  11     All rights reserved.
  12
  13     Redistribution and use in source and binary forms, with or without
  14     modification, are permitted provided that the following conditions are met:
  15     1. Redistributions of source code must retain the above copyright
  16     notice, this list of conditions and the following disclaimer.
  17     2. Redistributions in binary form must reproduce the above copyright
  18     notice, this list of conditions and the following disclaimer in the
  19     documentation and/or other materials provided with the distribution.
  20     3. Neither the name of the copyright holders nor the
  21     names of its contributors may be used to endorse or promote products
  22     derived from this software without specific prior written permission.
  23
  24     THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS ''AS IS'' AND ANY
  25     EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
  26     WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
  27     DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER BE LIABLE FOR ANY
  28     DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
  29     (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
  30     LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
  31     ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
  32     (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
  33     SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  34 */
  35 /**************************************************************************/
  36
  37 #ifndef _PROJECTCONFIG_H_
  38 #define _PROJECTCONFIG_H_
  39
  40 #include "lpc134x.h"
  41 #include "sysdefs.h"
  42
  43 /*=========================================================================
  44     BOARD SELECTION
  45
  46     Because several boards use this code library with sometimes slightly
  47     different pin configuration, you will need to specify which board you
  48     are using by enabling one of the following definitions. The code base
  49     will then try to configure itself accordingly for that board.
  50
  51     CFG_BRD_LPC1343_REFDESIGN
  52     =========================
  53
  54         microBuilder.eu LPC1343 Reference Design base board with
  55         on-board peripherals initialised (EEPROM, USB or UART CLI, etc.)
  56
  57                 This is the recommended starting point for new development
  58                 since it makes it easy to send printf output to USB CDC, access
  59                 the on-board EEPROM, etc.
  60
  61     CFG_BRD_LPC1343_REFDESIGN_MINIMAL
  62     =================================
  63
  64         microBuilder.eu LPC1343 Reference Design base board with
  65         only the most common peripherals initialised by default.
  66
  67         Results in smallest code since EEPROM, USB, etc., are not
  68         initialised on startup.  By default, only the following
  69         peripherals are initialised by systemInit():
  70
  71               - CPU (Configures the PLL, etc.)
  72               - GPIO
  73               - SysTick Timer
  74               - UART (with printf support) *
  75
  76         * Can be removed to save 0.8kb in debug and 0.3 kb in
  77         release. Comment out 'CFG_PRINTF_UART' to disable it.
  78
  79         The code size can be further reduced by several KB by removing
  80         any IRQ Handlers that are not used.  The I2C IRQHandler, for
  81         example, uses ~1KB of flash in debug and ~400KB in release mode,
  82         but because it is referenced in the startup code it is always
  83         included even if I2C is never used in the project.
  84
  85         Other IRQ Handlers that you might be able to comment out
  86         to save some space are:
  87
  88         IRQ Handler               Debug   Release
  89         ------------------------- ------  -------
  90         I2C_IRQHandler            1160 b    400 b
  91         SSP_IRQHandler             160 b     76 b
  92         UART_IRQHandler            246 b    116 b
  93         WAKEUP_IRQHandler          160 b    100 b
  94         WDT_IRQHandler              50 b     28 b
  95
  96     CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
  97     ====================================
  98
  99         microBuilder.eu/Adafruit Stand-Alone "Smart LCD" with USB enabled
 100         for the CLI interface.
 101
 102     CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 103     =====================================
 104
 105         microBuilder.eu/Adafruit Stand-Alone "Smart LCD" with UART enabled
 106         for the CLI interface.
 107
 108     CFG_BRD_LPC1343_802154USBSTICK
 109     ==============================
 110
 111         microBuilder.eu USB stick 802.15.4 868/915MHz RF transceiver
 112
 113     CFG_BRD_LPC1343_OLIMEX_P
 114     ==============================
 115
 116         Simple Olimex LPC1343 breakout board
 117
 118     CFG_BRD_LPC1343_LPCXPRESSO
 119     ==============================
 120
 121         LPC1343 LPCXpresso board
 122
 123     -----------------------------------------------------------------------*/
 124 // #define CFG_BRD_LPC1343_REFDESIGN
 125 #define CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 126     // #define CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
 127     // #define CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 128     // #define CFG_BRD_LPC1343_802154USBSTICK
 129     // #define CFG_BRD_LPC1343_OLIMEX_P
 130     // #define CFG_BRD_LPC1343_LPCXPRESSO
 131 /*=========================================================================*/
 132
 133
 134 /**************************************************************************
 135     PIN USAGE
 136     -----------------------------------------------------------------------
 137     This table tries to give an indication of which GPIO pins and
 138     peripherals are used by the available drivers and SW examples.  Only
 139     dedicated GPIO pins available on the LPC1343 Reference Board are shown
 140     below.  Any unused peripheral blocks like I2C, SSP, ADC, etc., can
 141     also be used as GPIO if they are available.
 142
 143                 PORT 1        PORT 2                PORT 3
 144                 =========     =================     =======
 145                 8 9 10 11     1 2 3 4 5 6 7 8 9     0 1 2 3
 146
 147     SDCARD      . .  .  .     . . . . . . . . .     X . . .
 148     PWM         . X  .  .     . . . . . . . . .     . . . .
 149     STEPPER     . .  .  .     . . . . . . . . .     X X X X
 150     CHIBI       X X  X  .     . . . . . . . . .     . . . .
 151     ILI9325/8   X X  X  X     X X X X X X X X X     . . . X
 152     ST7565      X X  X  X     X X X X X X X X X     . . . X
 153     ST7735      . .  .  .     X X X X X X . . .     . . . .
 154     SHARPMEM    . .  .  .     X X X X . . . . .     . . . .
 155     SSD1306 SPI . .  .  .     X X X . X X . . .     . . . .
 156     SSD1351     . .  .  .     X X X X X . . . .     . . . .
 157     MCP121      . .  .  .     . . . . . . . . .     . X . .
 158     PN532 [3]   . .  .  .     . . . . . . . . .     . X X .
 159
 160                 TIMERS                    SSP     ADC         UART
 161                 ======================    ===     =======     ====
 162                 16B0  16B1  32B0  32B1    0       0 1 2 3     0
 163
 164     SDCARD      .     .     .     .       X       . . . .     .
 165     PWM         .     X     .     .       .       . . . .     .
 166     PMU [1]     .     .     X     .       .       . . . .     .
 167     USB         .     .     .     X       .       . . . .     .
 168     STEPPER     .     .     X     .       .       . . . .     .
 169     CHIBI       x     .     .     .       X       . . . .     .
 170     ILI9325/8   .     .     .     .       .       X X X X     .
 171     ST7565      .     .     .     .       .       X X X X     .
 172     ST7535      .     .     .     .       .       . . . .     .
 173     SHARPMEM    .     .     .     .       .       . . . .     .
 174     SSD1306 SPI .     .     .     .       .       . . . .     .
 175     INTERFACE   .     .     .     .       .       . . . .     X[2]
 176
 177     [1]  PMU uses 32-bit Timer 0 for SW wakeup from deep-sleep.  This timer
 178          can safely be used by other peripherals, but may need to be
 179          reconfigured when you wakeup from deep-sleep.
 180     [2]  INTERFACE can be configured to use either USBCDC or UART
 181     [3]  P3.2 is only used with the I2C bus (for IRQ)
 182
 183  **************************************************************************/
 184
 185
 186 /**************************************************************************
 187     I2C Addresses
 188     -----------------------------------------------------------------------
 189     The following addresses are used by the different I2C sensors included
 190     in the code base [1]
 191
 192                                 HEX       BINARY
 193                                 ====      ========
 194     ISL12022M (RTC)             0xDE      1101111x
 195     ISL12022M (SRAM)            0xAE      1010111x
 196     LM75B                       0x90      1001000x
 197     MCP24AA                     0xA0      1010000x
 198     MCP4725                     0xC0      1100000x ***
 199     TEA5767                     0xC0      1100000x ***
 200     TSL2561                     0x72      0111001x
 201     TCS3414                     0x72      0111001x
 202     PN532                       0x48      0100100x
 203     SSD1306_I2C                 0x78      0111100x  // Assumes SA0 = GND
 204     INA219                      0xF0      10000000x // Assumes A0+A1 = GND
 205
 206     [1]  Alternative addresses may exists, but the addresses listed in this
 207          table are the values used in the code base
 208
 209  **************************************************************************/
 210
 211
 212 /*=========================================================================
 213     FIRMWARE VERSION SETTINGS
 214     -----------------------------------------------------------------------*/
 215     #define CFG_FIRMWARE_VERSION_MAJOR            (1)
 216     #define CFG_FIRMWARE_VERSION_MINOR            (1)
 217     #define CFG_FIRMWARE_VERSION_REVISION         (0)
 218 /*=========================================================================*/
 219
 220
 221 /*=========================================================================
 222     CORE CPU SETTINGS
 223     -----------------------------------------------------------------------
 224
 225     CFG_CPU_CCLK    Value is for reference only.  'core/cpu/cpu.c' must
 226                     be modified to change the clock speed, but the value
 227                     should be indicated here since CFG_CPU_CCLK is used by
 228                     other peripherals to determine timing.
 229
 230     -----------------------------------------------------------------------*/
 231     #define CFG_CPU_CCLK                (72000000)  // 1 tick = 13.88nS
 232 /*=========================================================================*/
 233
 234
 235 /*=========================================================================
 236     SYSTICK TIMER
 237     -----------------------------------------------------------------------
 238
 239     CFG_SYSTICK_DELAY_IN_MS   The number of milliseconds between each tick
 240                               of the systick timer.
 241
 242     -----------------------------------------------------------------------*/
 243     #define CFG_SYSTICK_DELAY_IN_MS     (1)
 244 /*=========================================================================*/
 245
 246
 247 /*=========================================================================
 248     GPIO INTERRUPTS
 249     -----------------------------------------------------------------------
 250
 251     IF you wish to use the GPIO interrupt handlers elsewhere in your code,
 252     you should probably define a seperate IRQHandler for the appropriate
 253     GPIO bank rather than using the definitions in core/gpio/gpio.c (to
 254     avoid causing problems in other projects, and to make updates easier,
 255     etc.)  To disable the default IRQHandler, simply comment out the
 256     define below for the appropriate GPIO bank and implement the handler
 257     somewhere else.
 258
 259     GPIO_ENABLE_IRQ0    If defined, PIOINT0_IRQHandler will be declared and
 260                         handled in core/gpio/gpio.c
 261     GPIO_ENABLE_IRQ1    If defined, PIOINT1_IRQHandler will be declared and
 262                         handled in core/gpio/gpio.c
 263     GPIO_ENABLE_IRQ2    If defined, PIOINT2_IRQHandler will be declared and
 264                         handled in core/gpio/gpio.c
 265     GPIO_ENABLE_IRQ3    If defined, PIOINT3_IRQHandler will be declared and
 266                         handled in core/gpio/gpio.c
 267
 268     -----------------------------------------------------------------------*/
 269     #ifdef CFG_BRD_LPC1343_REFDESIGN
 270       // #define GPIO_ENABLE_IRQ0
 271       #define GPIO_ENABLE_IRQ1
 272       // #define GPIO_ENABLE_IRQ2
 273       // #define GPIO_ENABLE_IRQ3
 274     #endif
 275
 276     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 277       // #define GPIO_ENABLE_IRQ0
 278       #define GPIO_ENABLE_IRQ1
 279       // #define GPIO_ENABLE_IRQ2
 280       // #define GPIO_ENABLE_IRQ3
 281     #endif
 282
 283     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
 284       // #define GPIO_ENABLE_IRQ0
 285       #define GPIO_ENABLE_IRQ1
 286       // #define GPIO_ENABLE_IRQ2
 287       // #define GPIO_ENABLE_IRQ3
 288     #endif
 289
 290     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 291       // #define GPIO_ENABLE_IRQ0
 292       #define GPIO_ENABLE_IRQ1
 293       // #define GPIO_ENABLE_IRQ2
 294       // #define GPIO_ENABLE_IRQ3
 295     #endif
 296
 297     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 298       // #define GPIO_ENABLE_IRQ0
 299       #define GPIO_ENABLE_IRQ1
 300       // #define GPIO_ENABLE_IRQ2
 301       // #define GPIO_ENABLE_IRQ3
 302     #endif
 303
 304     #ifdef CFG_BRD_LPC1343_OLIMEX_P
 305       // #define GPIO_ENABLE_IRQ0
 306       #define GPIO_ENABLE_IRQ1
 307       // #define GPIO_ENABLE_IRQ2
 308       // #define GPIO_ENABLE_IRQ3
 309     #endif
 310
 311     #ifdef CFG_BRD_LPC1343_LPCXPRESSO
 312       // #define GPIO_ENABLE_IRQ0
 313       #define GPIO_ENABLE_IRQ1
 314       // #define GPIO_ENABLE_IRQ2
 315       // #define GPIO_ENABLE_IRQ3
 316     #endif
 317 /*=========================================================================*/
 318
 319
 320 /*=========================================================================
 321     ALTERNATE RESET PIN
 322     -----------------------------------------------------------------------
 323
 324     CFG_ALTRESET        If defined, indicates that a GPIO pin should be
 325                         configured as an alternate reset pin in addition
 326                         to the dedicated reset pin.
 327     CFG_ALTRESET_PORT   The GPIO port where the alt reset pin is located
 328     CFG_ALTRESET_PIN    The GPIO pin where the alt reset pin is located
 329
 330     -----------------------------------------------------------------------*/
 331     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 332       #define CFG_ALTRESET
 333       #define CFG_ALTRESET_PORT         (1)
 334       #define CFG_ALTRESET_PIN          (5)   // P1.5 = RTS
 335     #endif
 336 /*=========================================================================*/
 337
 338
 339 /*=========================================================================
 340     UART
 341     -----------------------------------------------------------------------
 342
 343     CFG_UART_BAUDRATE         The default UART speed.  This value is used
 344                               when initialising UART, and should be a
 345                               standard value like 57600, 9600, etc.
 346                               NOTE: This value may be overridden if
 347                               another value is stored in EEPROM!
 348     CFG_UART_BUFSIZE          The length in bytes of the UART RX FIFO. This
 349                               will determine the maximum number of received
 350                               characters to store in memory.
 351
 352     -----------------------------------------------------------------------*/
 353     #ifdef CFG_BRD_LPC1343_REFDESIGN
 354       #define CFG_UART_BAUDRATE           (115200)
 355       #define CFG_UART_BUFSIZE            (512)
 356     #endif
 357
 358     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 359       #define CFG_UART_BAUDRATE           (115200)
 360       #define CFG_UART_BUFSIZE            (512)
 361     #endif
 362
 363     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
 364       #define CFG_UART_BAUDRATE           (115200)
 365       #define CFG_UART_BUFSIZE            (512)
 366     #endif
 367
 368     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 369       #define CFG_UART_BAUDRATE           (57600)
 370       #define CFG_UART_BUFSIZE            (512)
 371     #endif
 372
 373     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 374       #define CFG_UART_BAUDRATE           (115200)
 375       #define CFG_UART_BUFSIZE            (512)
 376     #endif
 377
 378     #ifdef CFG_BRD_LPC1343_OLIMEX_P
 379       #define CFG_UART_BAUDRATE           (115200)
 380       #define CFG_UART_BUFSIZE            (512)
 381     #endif
 382
 383     #ifdef CFG_BRD_LPC1343_LPCXPRESSO
 384       #define CFG_UART_BAUDRATE           (115200)
 385       #define CFG_UART_BUFSIZE            (512)
 386     #endif
 387 /*=========================================================================*/
 388
 389
 390 /*=========================================================================
 391     SSP
 392     -----------------------------------------------------------------------
 393
 394     CFG_SSP0_SCKPIN_2_11      Indicates which pin should be used for SCK0
 395     CFG_SSP0_SCKPIN_0_6
 396
 397     -----------------------------------------------------------------------*/
 398     #ifdef CFG_BRD_LPC1343_REFDESIGN
 399       #define CFG_SSP0_SCKPIN_2_11
 400       // #define CFG_SSP0_SCKPIN_0_6
 401     #endif
 402
 403     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 404       #define CFG_SSP0_SCKPIN_2_11
 405       // #define CFG_SSP0_SCKPIN_0_6
 406     #endif
 407
 408     #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 409       #define CFG_SSP0_SCKPIN_2_11
 410       // #define CFG_SSP0_SCKPIN_0_6
 411     #endif
 412
 413     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 414       // #define CFG_SSP0_SCKPIN_2_11
 415       #define CFG_SSP0_SCKPIN_0_6
 416     #endif
 417
 418     #ifdef CFG_BRD_LPC1343_OLIMEX_P
 419       #define CFG_SSP0_SCKPIN_2_11
 420       // #define CFG_SSP0_SCKPIN_0_6
 421     #endif
 422
 423     #ifdef CFG_BRD_LPC1343_LPCXPRESSO
 424       #define CFG_SSP0_SCKPIN_2_11
 425       // #define CFG_SSP0_SCKPIN_0_6
 426     #endif
 427 /*=========================================================================*/
 428
 429
 430 /*=========================================================================
 431     ADC
 432     -----------------------------------------------------------------------
 433
 434     ADC_AVERAGING_ENABLE      To get better results, the ADC code can take
 435                               a number of samples and return the average
 436                               value.  This is slower, but can give more
 437                               accurate results compared to single-reading.
 438
 439                               To enable averaging, set ADC_AVERAGING_ENABLE
 440                               to a non-zero value.
 441     ADC_AVERAGING_SAMPLES     The number of ADC samples to read and
 442                               average if ADC averaging is enabled.
 443
 444     -----------------------------------------------------------------------*/
 445     #ifdef CFG_BRD_LPC1343_REFDESIGN
 446       #define ADC_AVERAGING_ENABLE    (1)
 447       #define ADC_AVERAGING_SAMPLES   (5)
 448     #endif
 449
 450     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 451       #define ADC_AVERAGING_ENABLE    (1)
 452       #define ADC_AVERAGING_SAMPLES   (5)
 453     #endif
 454
 455     #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 456       #define ADC_AVERAGING_ENABLE    (0)
 457       #define ADC_AVERAGING_SAMPLES   (5)
 458     #endif
 459
 460     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 461       #define ADC_AVERAGING_ENABLE    (0)
 462       #define ADC_AVERAGING_SAMPLES   (5)
 463     #endif
 464
 465     #ifdef CFG_BRD_LPC1343_OLIMEX_P
 466       #define ADC_AVERAGING_ENABLE    (0)
 467       #define ADC_AVERAGING_SAMPLES   (5)
 468     #endif
 469
 470     #ifdef CFG_BRD_LPC1343_LPCXPRESSO
 471       #define ADC_AVERAGING_ENABLE    (0)
 472       #define ADC_AVERAGING_SAMPLES   (5)
 473     #endif
 474 /*=========================================================================*/
 475
 476
 477 /*=========================================================================
 478     ON-BOARD LED
 479     -----------------------------------------------------------------------
 480
 481     CFG_LED_PORT              The port for the on board LED
 482     CFG_LED_PIN               The pin for the on board LED
 483     CFG_LED_ON                The pin state to turn the LED on (0 = low, 1 = high)
 484     CFG_LED_OFF               The pin state to turn the LED off (0 = low, 1 = high)
 485
 486     -----------------------------------------------------------------------*/
 487     #ifdef CFG_BRD_LPC1343_REFDESIGN
 488       #define CFG_LED_PORT                (2)
 489       #define CFG_LED_PIN                 (10)
 490       #define CFG_LED_ON                  (0)
 491       #define CFG_LED_OFF                 (1)
 492     #endif
 493
 494     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 495       #define CFG_LED_PORT                (2)
 496       #define CFG_LED_PIN                 (10)
 497       #define CFG_LED_ON                  (0)
 498       #define CFG_LED_OFF                 (1)
 499     #endif
 500
 501     #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 502       #define CFG_LED_PORT                (2)
 503       #define CFG_LED_PIN                 (10)
 504       #define CFG_LED_ON                  (0)
 505       #define CFG_LED_OFF                 (1)
 506     #endif
 507
 508     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 509       #define CFG_LED_PORT                (3)
 510       #define CFG_LED_PIN                 (2)
 511       #define CFG_LED_ON                  (0)
 512       #define CFG_LED_OFF                 (1)
 513     #endif
 514
 515     #ifdef CFG_BRD_LPC1343_OLIMEX_P
 516       #define CFG_LED_PORT                (3)
 517       #define CFG_LED_PIN                 (2)
 518       #define CFG_LED_ON                  (0)
 519       #define CFG_LED_OFF                 (1)
 520     #endif
 521
 522     #ifdef CFG_BRD_LPC1343_LPCXPRESSO
 523       #define CFG_LED_PORT                (0)
 524       #define CFG_LED_PIN                 (7)
 525       #define CFG_LED_ON                  (0)
 526       #define CFG_LED_OFF                 (1)
 527     #endif
 528 /*=========================================================================*/
 529
 530
 531 /*=========================================================================
 532     MICRO-SD CARD
 533     -----------------------------------------------------------------------
 534
 535     CFG_SDCARD                If this field is defined SD Card and FAT32
 536                               file system support will be included
 537     CFG_SDCARD_READONLY       If this is set to 1, all commands to
 538                               write to the SD card will be removed
 539                               saving some flash space.
 540     CFG_SDCARD_CDPORT         The card detect port number
 541     CFG_SDCARD_CDPIN          The card detect pin number
 542
 543     NOTE:                     All config settings for FAT32 are defined
 544                               in ffconf.h
 545
 546     BENCHMARK:                With SPI set to 6.0MHz, FATFS can read
 547                               ~300KB/s (w/512 byte read buffer)
 548
 549     PIN LAYOUT:               The pin layout that is used by this driver
 550                               can be seen in the following schematic:
 551                               /tools/schematics/Breakout_TFTLCD_ILI9325_v1.3
 552
 553     DEPENDENCIES:             SDCARD requires the use of SSP0.
 554     -----------------------------------------------------------------------*/
 555     #ifdef CFG_BRD_LPC1343_REFDESIGN
 556       // #define CFG_SDCARD
 557       #define CFG_SDCARD_READONLY         (1)   // Must be 0 or 1
 558       #define CFG_SDCARD_CDPORT           (3)
 559       #define CFG_SDCARD_CDPIN            (0)
 560     #endif
 561
 562     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 563       // #define CFG_SDCARD
 564       #define CFG_SDCARD_READONLY         (1)   // Must be 0 or 1
 565       #define CFG_SDCARD_CDPORT           (3)
 566       #define CFG_SDCARD_CDPIN            (0)
 567     #endif
 568
 569     #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 570       #define CFG_SDCARD
 571       #define CFG_SDCARD_READONLY         (1)   // Must be 0 or 1
 572       #define CFG_SDCARD_CDPORT           (3)
 573       #define CFG_SDCARD_CDPIN            (0)
 574     #endif
 575
 576     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 577       // #define CFG_SDCARD
 578       #define CFG_SDCARD_READONLY         (1)   // Must be 0 or 1
 579       #define CFG_SDCARD_CDPORT           (3)
 580       #define CFG_SDCARD_CDPIN            (0)
 581     #endif
 582
 583     #ifdef CFG_BRD_LPC1343_OLIMEX_P
 584       // #define CFG_SDCARD
 585       #define CFG_SDCARD_READONLY         (1) // Must be 0 or 1
 586       #define CFG_SDCARD_CDPORT           (3)
 587       #define CFG_SDCARD_CDPIN            (0)
 588     #endif
 589
 590     #ifdef CFG_BRD_LPC1343_LPCXPRESSO
 591       // #define CFG_SDCARD
 592       #define CFG_SDCARD_READONLY         (1) // Must be 0 or 1
 593       #define CFG_SDCARD_CDPORT           (3)
 594       #define CFG_SDCARD_CDPIN            (0)
 595     #endif
 596 /*=========================================================================*/
 597
 598
 599 /*=========================================================================
 600     USB
 601     -----------------------------------------------------------------------
 602
 603     CFG_USBHID                If this field is defined USB HID support will
 604                               be included.  Currently uses ROM-based USB HID
 605     CFG_USBCDC                If this field is defined USB CDC support will
 606                               be included, with the USB Serial Port speed
 607                               set to 115200 BPS by default
 608     CFG_USBCDC_BAUDRATE       The default TX/RX speed.  This value is used
 609                               when initialising USBCDC, and should be a
 610                               standard value like 57600, 9600, etc.
 611     CFG_USBCDC_INITTIMEOUT    The maximum delay in milliseconds to wait for
 612                               USB to connect.  Must be a multiple of 10!
 613     CFG_USBCDC_BUFFERSIZE     Size of the buffer (in bytes) that stores
 614                               printf data until it can be sent out in
 615                               64 byte frames.  The buffer is required since
 616                               only one frame per ms can be sent using USB
 617                               CDC (see 'puts' in systeminit.c).
 618
 619     -----------------------------------------------------------------------*/
 620 #define CFG_USBMSC (1)
 621
 622
 623     #define CFG_USB_VID                   (0x239A)
 624     #define CFG_USB_PID                   (0x1002)
 625
 626     #ifdef CFG_BRD_LPC1343_REFDESIGN
 627       // #define CFG_USBHID
 628       #define CFG_USBCDC
 629       #define CFG_USBCDC_BAUDRATE         (115200)
 630       #define CFG_USBCDC_INITTIMEOUT      (5000)
 631       #define CFG_USBCDC_BUFFERSIZE       (256)
 632     #endif
 633
 634     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 635       // #define CFG_USBHID
 636       // #define CFG_USBCDC
 637       #define CFG_USBCDC_BAUDRATE         (115200)
 638       #define CFG_USBCDC_INITTIMEOUT      (5000)
 639       #define CFG_USBCDC_BUFFERSIZE       (256)
 640     #endif
 641
 642     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
 643       // #define CFG_USBHID
 644       #define CFG_USBCDC
 645       #define CFG_USBCDC_BAUDRATE         (115200)
 646       #define CFG_USBCDC_INITTIMEOUT      (5000)
 647       #define CFG_USBCDC_BUFFERSIZE       (256)
 648     #endif
 649
 650     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 651       // #define CFG_USBHID
 652       // #define CFG_USBCDC
 653       #define CFG_USBCDC_BAUDRATE         (57600)
 654       #define CFG_USBCDC_INITTIMEOUT      (5000)
 655       #define CFG_USBCDC_BUFFERSIZE       (256)
 656     #endif
 657
 658     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 659       // #define CFG_USBHID
 660       #define CFG_USBCDC
 661       #define CFG_USBCDC_BAUDRATE         (115200)
 662       #define CFG_USBCDC_INITTIMEOUT      (5000)
 663       #define CFG_USBCDC_BUFFERSIZE       (256)
 664     #endif
 665
 666     #ifdef CFG_BRD_LPC1343_OLIMEX_P
 667       // #define CFG_USBHID
 668       #define CFG_USBCDC
 669       #define CFG_USBCDC_BAUDRATE         (115200)
 670       #define CFG_USBCDC_INITTIMEOUT      (5000)
 671       #define CFG_USBCDC_BUFFERSIZE       (256)
 672     #endif
 673
 674     #ifdef CFG_BRD_LPC1343_LPCXPRESSO
 675       // #define CFG_USBHID
 676       #define CFG_USBCDC
 677       #define CFG_USBCDC_BAUDRATE         (115200)
 678       #define CFG_USBCDC_INITTIMEOUT      (5000)
 679       #define CFG_USBCDC_BUFFERSIZE       (256)
 680     #endif
 681 /*=========================================================================*/
 682
 683
 684 /*=========================================================================
 685     PRINTF REDIRECTION
 686     -----------------------------------------------------------------------
 687
 688     CFG_PRINTF_MAXSTRINGSIZE  Maximum size of string buffer for printf
 689     CFG_PRINTF_UART           Will cause all printf statements to be
 690                               redirected to UART
 691     CFG_PRINTF_USBCDC         Will cause all printf statements to be
 692                               redirect to USB Serial
 693     CFG_PRINTF_NEWLINE        This is typically "\r\n" for Windows or
 694                               "\n" for *nix
 695
 696     Note: If no printf redirection definitions are present, all printf
 697     output will be ignored.
 698     -----------------------------------------------------------------------*/
 699     #ifdef CFG_BRD_LPC1343_REFDESIGN
 700       #define CFG_PRINTF_MAXSTRINGSIZE    (255)
 701       // #define CFG_PRINTF_UART
 702       #define CFG_PRINTF_USBCDC
 703       #define CFG_PRINTF_NEWLINE          "\r\n"
 704     #endif
 705
 706     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 707       #define CFG_PRINTF_MAXSTRINGSIZE    (255)
 708       // #define CFG_PRINTF_UART
 709       // #define CFG_PRINTF_USBCDC
 710       #define CFG_PRINTF_NEWLINE          "\r\n"
 711     #endif
 712
 713     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
 714       #define CFG_PRINTF_MAXSTRINGSIZE    (255)
 715       // #define CFG_PRINTF_UART
 716       #define CFG_PRINTF_USBCDC
 717       #define CFG_PRINTF_NEWLINE          "\r\n"
 718     #endif
 719
 720     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 721       #define CFG_PRINTF_MAXSTRINGSIZE    (255)
 722       #define CFG_PRINTF_UART
 723       // #define CFG_PRINTF_USBCDC
 724       #define CFG_PRINTF_NEWLINE          "\n"
 725     #endif
 726
 727     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 728       #define CFG_PRINTF_MAXSTRINGSIZE    (255)
 729       // #define CFG_PRINTF_UART
 730       #define CFG_PRINTF_USBCDC
 731       #define CFG_PRINTF_NEWLINE          "\r\n"
 732     #endif
 733
 734     #ifdef CFG_BRD_LPC1343_OLIMEX_P
 735       #define CFG_PRINTF_MAXSTRINGSIZE    (255)
 736       // #define CFG_PRINTF_UART
 737       #define CFG_PRINTF_USBCDC
 738       #define CFG_PRINTF_NEWLINE          "\r\n"
 739     #endif
 740
 741     #ifdef CFG_BRD_LPC1343_LPCXPRESSO
 742       #define CFG_PRINTF_MAXSTRINGSIZE    (255)
 743       // #define CFG_PRINTF_UART
 744       #define CFG_PRINTF_USBCDC
 745       #define CFG_PRINTF_NEWLINE          "\r\n"
 746     #endif
 747 /*=========================================================================*/
 748
 749
 750 /*=========================================================================
 751     COMMAND LINE INTERFACE
 752     -----------------------------------------------------------------------
 753
 754     CFG_INTERFACE             If this field is defined the UART or USBCDC
 755                               based command-line interface will be included
 756     CFG_INTERFACE_MAXMSGSIZE  The maximum number of bytes to accept for an
 757                               incoming command
 758     CFG_INTERFACE_PROMPT      The command prompt to display at the start
 759                               of every new data entry line
 760     CFG_INTERFACE_SILENTMODE  If this is set to 1 only text generated in
 761                               response to commands will be send to the
 762                               output buffer.  The command prompt will not
 763                               be displayed and incoming text will not be
 764                               echoed back to the output buffer (allowing
 765                               you to see the text you have input).  This
 766                               is normally only desirable in a situation
 767                               where another MCU is communicating with
 768                               the LPC1343.
 769     CFG_INTERFACE_DROPCR      If this is set to 1 all incoming \r
 770                               characters will be dropped
 771     CFG_INTERFACE_ENABLEIRQ   If this is set to 1 the IRQ pin will be
 772                               set high when a command starts executing
 773                               and will go low when the command has
 774                               finished executing or the LCD is not busy.
 775                               This allows another device to know when a
 776                               new command can safely be sent.
 777     CFG_INTERFACE_IRQPORT     The gpio port for the IRQ/busy pin
 778     CFG_INTERFACE_IRQPIN      The gpio pin number for the IRQ/busy pin
 779     CFG_INTERFACE_SHORTERRORS If this is enabled only short 1 character
 780                               error messages will be returned (followed
 781                               by CFG_PRINTF_NEWLINE), rather than more
 782                               verbose error messages.  The specific
 783                               characters used are defined below.
 784     CFG_INTERFACE_CONFIRMREADY  If this is set to 1 a text confirmation
 785                               will be sent when the command prompt is
 786                               ready for a new command.  This is in
 787                               addition to CFG_INTERFACE_ENABLEIRQ if
 788                               this is also enabled.  The character used
 789                               is defined below.
 790     CFG_INTERFACE_LONGSYSINFO If this is set to 1 extra information will
 791                               be included in the Sys Info ('V') command
 792                               on the CLI. This can be useful when trying
 793                               to debug problems on remote HW, or with
 794                               unknown firmware.  It will also use about
 795                               0.5KB flash, though, so only enable it is
 796                               necessary.
 797
 798     NOTE:                     The command-line interface will use either
 799                               USB-CDC or UART depending on whether
 800                               CFG_PRINTF_UART or CFG_PRINTF_USBCDC are
 801                               selected.
 802     -----------------------------------------------------------------------*/
 803     #ifdef CFG_BRD_LPC1343_REFDESIGN
 804       #define CFG_INTERFACE
 805       #define CFG_INTERFACE_MAXMSGSIZE    (256)
 806       #define CFG_INTERFACE_PROMPT        "LPC1343 >> "
 807       #define CFG_INTERFACE_SILENTMODE    (0)
 808       #define CFG_INTERFACE_DROPCR        (0)
 809       #define CFG_INTERFACE_ENABLEIRQ     (0)
 810       #define CFG_INTERFACE_IRQPORT       (0)
 811       #define CFG_INTERFACE_IRQPIN        (7)
 812       #define CFG_INTERFACE_SHORTERRORS   (0)
 813       #define CFG_INTERFACE_CONFIRMREADY  (0)
 814       #define CFG_INTERFACE_LONGSYSINFO   (0)
 815     #endif
 816
 817     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 818       // #define CFG_INTERFACE
 819       #define CFG_INTERFACE_MAXMSGSIZE    (256)
 820       #define CFG_INTERFACE_PROMPT        "LPC1343 >> "
 821       #define CFG_INTERFACE_SILENTMODE    (0)
 822       #define CFG_INTERFACE_DROPCR        (0)
 823       #define CFG_INTERFACE_ENABLEIRQ     (0)
 824       #define CFG_INTERFACE_IRQPORT       (0)
 825       #define CFG_INTERFACE_IRQPIN        (7)
 826       #define CFG_INTERFACE_SHORTERRORS   (0)
 827       #define CFG_INTERFACE_CONFIRMREADY  (0)
 828       #define CFG_INTERFACE_LONGSYSINFO   (0)
 829     #endif
 830
 831     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
 832       #define CFG_INTERFACE
 833       #define CFG_INTERFACE_MAXMSGSIZE    (256)
 834       #define CFG_INTERFACE_PROMPT        "CMD >> "
 835       #define CFG_INTERFACE_SILENTMODE    (0)
 836       #define CFG_INTERFACE_DROPCR        (0)
 837       #define CFG_INTERFACE_ENABLEIRQ     (0)
 838       #define CFG_INTERFACE_IRQPORT       (0)
 839       #define CFG_INTERFACE_IRQPIN        (7)
 840       #define CFG_INTERFACE_SHORTERRORS   (0)
 841       #define CFG_INTERFACE_CONFIRMREADY  (0)
 842       #define CFG_INTERFACE_SHORTERRORS_UNKNOWNCOMMAND    "?"
 843       #define CFG_INTERFACE_SHORTERRORS_TOOMANYARGS       ">"
 844       #define CFG_INTERFACE_SHORTERRORS_TOOFEWARGS        "<"
 845       #define CFG_INTERFACE_CONFIRMREADY_TEXT             "."
 846       #define CFG_INTERFACE_LONGSYSINFO   (0)
 847     #endif
 848
 849     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 850       #define CFG_INTERFACE
 851       #define CFG_INTERFACE_MAXMSGSIZE    (256)
 852       #define CFG_INTERFACE_PROMPT        ">>"
 853       #define CFG_INTERFACE_SILENTMODE    (1)
 854       #define CFG_INTERFACE_DROPCR        (1)
 855       #define CFG_INTERFACE_ENABLEIRQ     (1)
 856       #define CFG_INTERFACE_IRQPORT       (0)
 857       #define CFG_INTERFACE_IRQPIN        (7)
 858       #define CFG_INTERFACE_SHORTERRORS   (1)
 859       #define CFG_INTERFACE_CONFIRMREADY  (0)
 860       #define CFG_INTERFACE_SHORTERRORS_UNKNOWNCOMMAND    "?"
 861       #define CFG_INTERFACE_SHORTERRORS_TOOMANYARGS       ">"
 862       #define CFG_INTERFACE_SHORTERRORS_TOOFEWARGS        "<"
 863       #define CFG_INTERFACE_CONFIRMREADY_TEXT             "."
 864       #define CFG_INTERFACE_LONGSYSINFO   (0)
 865     #endif
 866
 867     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 868       // #define CFG_INTERFACE
 869       #define CFG_INTERFACE_MAXMSGSIZE    (256)
 870       #define CFG_INTERFACE_PROMPT        "CMD >> "
 871       #define CFG_INTERFACE_SILENTMODE    (0)
 872       #define CFG_INTERFACE_DROPCR        (0)
 873       #define CFG_INTERFACE_ENABLEIRQ     (0)
 874       #define CFG_INTERFACE_IRQPORT       (0)
 875       #define CFG_INTERFACE_IRQPIN        (7)
 876       #define CFG_INTERFACE_SHORTERRORS   (0)
 877       #define CFG_INTERFACE_CONFIRMREADY  (0)
 878       #define CFG_INTERFACE_LONGSYSINFO   (0)
 879     #endif
 880
 881     #ifdef CFG_BRD_LPC1343_OLIMEX_P
 882       #define CFG_INTERFACE
 883       #define CFG_INTERFACE_MAXMSGSIZE    (256)
 884       #define CFG_INTERFACE_PROMPT        "LPC-P1343 >> "
 885       #define CFG_INTERFACE_SILENTMODE    (0)
 886       #define CFG_INTERFACE_DROPCR        (0)
 887       #define CFG_INTERFACE_ENABLEIRQ     (0)
 888       #define CFG_INTERFACE_IRQPORT       (0)
 889       #define CFG_INTERFACE_IRQPIN        (7)
 890       #define CFG_INTERFACE_SHORTERRORS   (0)
 891       #define CFG_INTERFACE_CONFIRMREADY  (0)
 892       #define CFG_INTERFACE_LONGSYSINFO   (0)
 893     #endif
 894
 895     #ifdef CFG_BRD_LPC1343_LPCXPRESSO
 896       #define CFG_INTERFACE
 897       #define CFG_INTERFACE_MAXMSGSIZE    (256)
 898       #define CFG_INTERFACE_PROMPT        "LPC-P1343 >> "
 899       #define CFG_INTERFACE_SILENTMODE    (0)
 900       #define CFG_INTERFACE_DROPCR        (0)
 901       #define CFG_INTERFACE_ENABLEIRQ     (0)
 902       #define CFG_INTERFACE_IRQPORT       (0)
 903       #define CFG_INTERFACE_IRQPIN        (7)
 904       #define CFG_INTERFACE_SHORTERRORS   (0)
 905       #define CFG_INTERFACE_CONFIRMREADY  (0)
 906       #define CFG_INTERFACE_LONGSYSINFO   (0)
 907     #endif
 908 /*=========================================================================*/
 909
 910
 911 /*=========================================================================
 912     PWM SETTINGS
 913     -----------------------------------------------------------------------
 914
 915     CFG_PWM                     If this is defined, a basic PWM driver
 916                                 will be included using 16-bit Timer 1 and
 917                                 Pin 1.9 (MAT0) for the PWM output.  In
 918                                 order to allow for a fixed number of
 919                                 pulses to be generated, some PWM-specific
 920                                 code is required in the 16-Bit Timer 1
 921                                 ISR.  See "core/timer16/timer16.c" for
 922                                 more information.
 923     CFG_PWM_DEFAULT_PULSEWIDTH  The default pulse width in ticks
 924     CFG_PWM_DEFAULT_DUTYCYCLE   The default duty cycle in percent
 925
 926     DEPENDENCIES:               PWM output requires the use of 16-bit
 927                                 timer 1 and pin 1.9 (CT16B1_MAT0).
 928     -----------------------------------------------------------------------*/
 929     // #define CFG_PWM
 930     #define CFG_PWM_DEFAULT_PULSEWIDTH  (CFG_CPU_CCLK / 1000)
 931     #define CFG_PWM_DEFAULT_DUTYCYCLE   (50)
 932 /*=========================================================================*/
 933
 934
 935 /*=========================================================================
 936     STEPPER MOTOR SETTINGS
 937     -----------------------------------------------------------------------
 938
 939     CFG_STEPPER                 If this is defined, a simple bi-polar
 940                                 stepper motor will be included for common
 941                                 H-bridge chips like the L293D or SN754410N
 942
 943     DEPENDENCIES:               STEPPER requires the use of pins 3.0-3 and
 944                                 32-bit Timer 0.
 945     -----------------------------------------------------------------------*/
 946     // #define CFG_STEPPER
 947 /*=========================================================================*/
 948
 949
 950 /*=========================================================================
 951     EEPROM
 952     -----------------------------------------------------------------------
 953
 954     CFG_I2CEEPROM             If defined, drivers for the onboard EEPROM
 955                               will be included during build
 956     CFG_I2CEEPROM_SIZE        The number of bytes available on the EEPROM
 957
 958     -----------------------------------------------------------------------*/
 959     #ifdef CFG_BRD_LPC1343_REFDESIGN
 960       #define CFG_I2CEEPROM
 961       #define CFG_I2CEEPROM_SIZE          (3072)
 962     #endif
 963
 964     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 965       // #define CFG_I2CEEPROM
 966       #define CFG_I2CEEPROM_SIZE          (3072)
 967     #endif
 968
 969     #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 970       #define CFG_I2CEEPROM
 971       #define CFG_I2CEEPROM_SIZE          (3072)
 972     #endif
 973
 974     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 975       #define CFG_I2CEEPROM
 976       #define CFG_I2CEEPROM_SIZE          (3072)
 977     #endif
 978
 979     #ifdef CFG_BRD_LPC1343_OLIMEX_P
 980       // #define CFG_I2CEEPROM
 981       #define CFG_I2CEEPROM_SIZE          (3072)
 982     #endif
 983
 984     #ifdef CFG_BRD_LPC1343_LPCXPRESSO
 985       // #define CFG_I2CEEPROM
 986       #define CFG_I2CEEPROM_SIZE          (3072)
 987     #endif
 988 /*=========================================================================*/
 989
 990
 991 /*=========================================================================
 992     EEPROM MEMORY MAP
 993     -----------------------------------------------------------------------
 994     EEPROM is used to persist certain user modifiable values to make
 995     sure that these changes remain in effect after a reset or hard
 996     power-down.  The addresses in EEPROM for these various system
 997     settings/values are defined below.  The first 256 bytes of EEPROM
 998     are reserved for this (0x0000..0x00FF).
 999
1000     CFG_EEPROM_RESERVED       The last byte of reserved EEPROM memory
1001
1002           EEPROM Address (0x0000..0x00FF)
1003           ===============================
1004           0 1 2 3 4 5 6 7 8 9 A B C D E F
1005     000x  x x x x x x x x . x x . . . . .   Chibi
1006     001x  . . . . . . . . . . . . . . . .
1007     002x  x x x x . . . . . . . . . . . .   UART
1008     003x  x x x x x x x x x x x x x x x x   Touch Screen Calibration
1009     004x  x x x x x x x x x x x x x x . .   Touch Screen Calibration
1010     005x  . . . . . . . . . . . . . . . .
1011     006x  . . . . . . . . . . . . . . . .
1012     007x  . . . . . . . . . . . . . . . .
1013     008x  . . . . . . . . . . . . . . . .
1014     009x  . . . . . . . . . . . . . . . .
1015     00Ax  . . . . . . . . . . . . . . . .
1016     00Bx  . . . . . . . . . . . . . . . .
1017     00Cx  . . . . . . . . . . . . . . . .
1018     00Dx  . . . . . . . . . . . . . . . .
1019     00Ex  . . . . . . . . . . . . . . . .
1020     00Fx  . . . . . . . . . . . . . . . .
1021
1022     -----------------------------------------------------------------------*/
1023     #define CFG_EEPROM_RESERVED                 (0x00FF)              // Protect first 256 bytes of memory
1024     #define CFG_EEPROM_CHIBI_IEEEADDR           (uint16_t)(0x0000)    // 8
1025     #define CFG_EEPROM_CHIBI_SHORTADDR          (uint16_t)(0x0009)    // 2
1026     #define CFG_EEPROM_UART_SPEED               (uint16_t)(0x0020)    // 4
1027     #define CFG_EEPROM_TOUCHSCREEN_CALIBRATED   (uint16_t)(0x0030)    // 1
1028     #define CFG_EEPROM_TOUCHSCREEN_CAL_AN       (uint16_t)(0x0031)    // 4
1029     #define CFG_EEPROM_TOUCHSCREEN_CAL_BN       (uint16_t)(0x0035)    // 4
1030     #define CFG_EEPROM_TOUCHSCREEN_CAL_CN       (uint16_t)(0x0039)    // 4
1031     #define CFG_EEPROM_TOUCHSCREEN_CAL_DN       (uint16_t)(0x003D)    // 4
1032     #define CFG_EEPROM_TOUCHSCREEN_CAL_EN       (uint16_t)(0x0041)    // 4
1033     #define CFG_EEPROM_TOUCHSCREEN_CAL_FN       (uint16_t)(0x0045)    // 4
1034     #define CFG_EEPROM_TOUCHSCREEN_CAL_DIVIDER  (uint16_t)(0x0049)    // 4
1035     #define CFG_EEPROM_TOUCHSCREEN_THRESHHOLD   (uint16_t)(0x004D)    // 1
1036 /*=========================================================================*/
1037
1038
1039 /*=========================================================================
1040     LM75B TEMPERATURE SENSOR
1041     -----------------------------------------------------------------------
1042
1043     CFG_LM75B                 If defined, drivers for an optional LM75B
1044                               temperature sensor will be included during
1045                               build (requires external HW)
1046
1047     -----------------------------------------------------------------------*/
1048     // #define CFG_LM75B
1049 /*=========================================================================*/
1050
1051
1052 /*=========================================================================
1053     CHIBI WIRELESS STACK
1054     -----------------------------------------------------------------------
1055
1056     CFG_CHIBI                   If defined, the CHIBI wireless stack will be
1057                                 included during build.  Requires external HW.
1058     CFG_CHIBI_MODE              The mode to use when receiving and transmitting
1059                                 wireless data.  See chb_drvr.h for possible values
1060     CFG_CHIBI_POWER             The power level to use when transmitting.  See
1061                                 chb_drvr.h for possible values
1062     CFG_CHIBI_CHANNEL           802.15.4 Channel (0 = 868MHz, 1-10 = 915MHz)
1063     CFG_CHIBI_PANID             16-bit PAN Identifier (ex.0x1234)
1064     CFG_CHIBI_PROMISCUOUS       Set to 1 to enabled promiscuous mode or
1065                                 0 to disable it.  If promiscuous mode is
1066                                 enabled be sure to set CFG_CHIBI_BUFFERSIZE
1067                                 to an appropriately large value (ex. 1024)
1068     CFG_CHIBI_BUFFERSIZE        The size of the message buffer in bytes
1069
1070     DEPENDENCIES:               Chibi requires the use of SSP0, 16-bit timer
1071                                 0 and pins 3.1, 3.2, 3.3.  It also requires
1072                                 the presence of CFG_I2CEEPROM.
1073
1074     NOTE:                       These settings are not relevant to all boards!
1075                                 'tools/schematics/AT86RF212LPC1114_v1.6.pdf'
1076                                 show how 'CHIBI' is meant to be connected
1077     -----------------------------------------------------------------------*/
1078     #ifdef CFG_BRD_LPC1343_REFDESIGN
1079       // #define CFG_CHIBI
1080       #define CFG_CHIBI_MODE              (0)                 // OQPSK_868MHZ
1081       #define CFG_CHIBI_POWER             (0xE9)              // CHB_PWR_EU2_3DBM
1082       #define CFG_CHIBI_CHANNEL           (0)                 // 868-868.6 MHz
1083       #define CFG_CHIBI_PANID             (0x1234)
1084       #define CFG_CHIBI_PROMISCUOUS       (0)
1085       #define CFG_CHIBI_BUFFERSIZE        (128)
1086     #endif
1087
1088     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
1089       // #define CFG_CHIBI
1090       #define CFG_CHIBI_MODE              (0)                 // OQPSK_868MHZ
1091       #define CFG_CHIBI_POWER             (0xE9)              // CHB_PWR_EU2_3DBM
1092       #define CFG_CHIBI_CHANNEL           (0)                 // 868-868.6 MHz
1093       #define CFG_CHIBI_PANID             (0x1234)
1094       #define CFG_CHIBI_PROMISCUOUS       (0)
1095       #define CFG_CHIBI_BUFFERSIZE        (128)
1096     #endif
1097
1098     #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
1099       // #define CFG_CHIBI
1100       #define CFG_CHIBI_MODE              (0)                 // OQPSK_868MHZ
1101       #define CFG_CHIBI_POWER             (0xE9)              // CHB_PWR_EU2_3DBM
1102       #define CFG_CHIBI_CHANNEL           (0)                 // 868-868.6 MHz
1103       #define CFG_CHIBI_PANID             (0x1234)
1104       #define CFG_CHIBI_PROMISCUOUS       (0)
1105       #define CFG_CHIBI_BUFFERSIZE        (128)
1106     #endif
1107
1108     #ifdef CFG_BRD_LPC1343_802154USBSTICK
1109       #define CFG_CHIBI
1110       #define CFG_CHIBI_MODE              (0)                 // OQPSK_868MHZ
1111       #define CFG_CHIBI_POWER             (0xE9)              // CHB_PWR_EU2_3DBM
1112       #define CFG_CHIBI_CHANNEL           (0)                 // 868-868.6 MHz
1113       #define CFG_CHIBI_PANID             (0x1234)
1114       #define CFG_CHIBI_PROMISCUOUS       (0)
1115       #define CFG_CHIBI_BUFFERSIZE        (1024)
1116     #endif
1117
1118     #ifdef CFG_BRD_LPC1343_OLIMEX_P
1119       // #define CFG_CHIBI
1120       #define CFG_CHIBI_MODE              (0)                 // OQPSK_868MHZ
1121       #define CFG_CHIBI_POWER             (0xE9)              // CHB_PWR_EU2_3DBM
1122       #define CFG_CHIBI_CHANNEL           (0)                 // 868-868.6 MHz
1123       #define CFG_CHIBI_PANID             (0x1234)
1124       #define CFG_CHIBI_PROMISCUOUS       (0)
1125       #define CFG_CHIBI_BUFFERSIZE        (128)
1126     #endif
1127
1128     #ifdef CFG_BRD_LPC1343_LPCXPRESSO
1129       // #define CFG_CHIBI
1130       #define CFG_CHIBI_MODE              (0)                 // OQPSK_868MHZ
1131       #define CFG_CHIBI_POWER             (0xE9)              // CHB_PWR_EU2_3DBM
1132       #define CFG_CHIBI_CHANNEL           (0)                 // 868-868.6 MHz
1133       #define CFG_CHIBI_PANID             (0x1234)
1134       #define CFG_CHIBI_PROMISCUOUS       (0)
1135       #define CFG_CHIBI_BUFFERSIZE        (128)
1136     #endif
1137 /*=========================================================================*/
1138
1139
1140 /*=========================================================================
1141     TFT LCD
1142     -----------------------------------------------------------------------
1143
1144     CFG_TFTLCD                  If defined, this will cause drivers for
1145                                 a pre-determined LCD screen to be included
1146                                 during build.  Only one LCD driver can be
1147                                 included during the build process (for ex.
1148                                 'drivers/displays/hw/ILI9325.c')
1149     CFG_TFTLCD_INCLUDESMALLFONTS If set to 1, smallfont support will be
1150                                 included for 3x6, 5x8, 7x8 and 8x8 fonts.
1151                                 This should only be enabled if these small
1152                                 fonts are required since there is already
1153                                 support for larger fonts generated with
1154                                 Dot Factory
1155                                 http://www.pavius.net/downloads/tools/53-the-dot-factory
1156     CFG_TFTLCD_USEAAFONTS       If set to a non-zero value, anti-aliased
1157                                 fonts will be used instead of regular 1-bit
1158                                 font.  These result in much higher-
1159                                 quality text, but the fonts are 2 or 4
1160                                 times larger than plain bitmap fonts and
1161                                 take a bit more rendering time to display.
1162     CFG_TFTLCD_TS_DEFAULTTHRESHOLD  Default minimum threshold to trigger a
1163                                 touch event with the touch screen (and exit
1164                                 from 'tsWaitForEvent' in touchscreen.c).
1165                                 Should be an 8-bit value somewhere between
1166                                 8 and 75 in normal circumstances.  This is
1167                                 the default value and may be overriden by
1168                                 a value stored in EEPROM.
1169     CFG_TFTLCD_TS_KEYPADDELAY   The delay in milliseconds between key
1170                                 presses in dialogue boxes
1171
1172     PIN LAYOUT:                 The pin layout that is used by this driver
1173                                 can be seen in the following schematic:
1174                                 /tools/schematics/Breakout_TFTLCD_ILI9325_v1.3
1175
1176     DEPENDENCIES:               TFTLCD requires the use of pins 1.8, 1.9,
1177                                 1.10, 1.11, 3.3 and 2.1-9.
1178     -----------------------------------------------------------------------*/
1179     #ifdef CFG_BRD_LPC1343_REFDESIGN
1180       // #define CFG_TFTLCD
1181       #define CFG_TFTLCD_INCLUDESMALLFONTS   (0)
1182       #define CFG_TFTLCD_USEAAFONTS          (0)
1183       #define CFG_TFTLCD_TS_DEFAULTTHRESHOLD (50)
1184       #define CFG_TFTLCD_TS_KEYPADDELAY      (100)
1185     #endif
1186
1187     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
1188       // #define CFG_TFTLCD
1189       #define CFG_TFTLCD_INCLUDESMALLFONTS   (0)
1190       #define CFG_TFTLCD_USEAAFONTS          (0)
1191       #define CFG_TFTLCD_TS_DEFAULTTHRESHOLD (50)
1192       #define CFG_TFTLCD_TS_KEYPADDELAY      (100)
1193     #endif
1194
1195     #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
1196       #define CFG_TFTLCD
1197       #define CFG_TFTLCD_INCLUDESMALLFONTS   (0)
1198       #define CFG_TFTLCD_USEAAFONTS          (0)
1199       #define CFG_TFTLCD_TS_DEFAULTTHRESHOLD (50)
1200       #define CFG_TFTLCD_TS_KEYPADDELAY      (100)
1201     #endif
1202
1203     #ifdef CFG_BRD_LPC1343_802154USBSTICK
1204       // #define CFG_TFTLCD
1205       #define CFG_TFTLCD_INCLUDESMALLFONTS   (0)
1206       #define CFG_TFTLCD_USEAAFONTS          (0)
1207       #define CFG_TFTLCD_TS_DEFAULTTHRESHOLD (50)
1208       #define CFG_TFTLCD_TS_KEYPADDELAY      (100)
1209     #endif
1210
1211     #ifdef CFG_BRD_LPC1343_OLIMEX_P
1212       // #define CFG_TFTLCD
1213       #define CFG_TFTLCD_INCLUDESMALLFONTS   (0)
1214       #define CFG_TFTLCD_USEAAFONTS          (0)
1215       #define CFG_TFTLCD_TS_DEFAULTTHRESHOLD (50)
1216       #define CFG_TFTLCD_TS_KEYPADDELAY      (100)
1217     #endif
1218
1219     #ifdef CFG_BRD_LPC1343_LPCXPRESSO
1220       // #define CFG_TFTLCD
1221       #define CFG_TFTLCD_INCLUDESMALLFONTS   (0)
1222       #define CFG_TFTLCD_USEAAFONTS          (0)
1223       #define CFG_TFTLCD_TS_DEFAULTTHRESHOLD (50)
1224       #define CFG_TFTLCD_TS_KEYPADDELAY      (100)
1225     #endif
1226 /*=========================================================================*/
1227
1228
1229 /*=========================================================================
1230     Monochrome/Bitmap Graphic LCDs
1231     -----------------------------------------------------------------------
1232
1233     CFG_ST7565                If defined, this will cause drivers for
1234                               the 128x64 pixel ST7565 LCD to be included
1235     CFG_SSD1306               If defined, this will cause drivers for
1236                               the 128x64 pixel SSD1306 OLED display to be
1237                               included (using bit-banged SPI)
1238     CFG_SHARPMEM              If defined, this will cause drivers for
1239                               Sharp Memory Displays to be included
1240
1241     DEPENDENCIES:             ST7565 requires the use of pins 2.1-6.
1242     DEPENDENCIES:             SSD1306 requires the use of pins 2.1-6.
1243     DEPENDENCIES:             SSD1306_I2C requires the use of pins 2.2.
1244     DEPENDENCIES:             SHARPMEM requires the use of pins 2.1-4.
1245     -----------------------------------------------------------------------*/
1246     // #define CFG_ST7565
1247     // #define CFG_SSD1306
1248     // #define CFG_SHARPMEM
1249 /*=========================================================================*/
1250
1251
1252 /*=========================================================================
1253     RSA Encryption
1254     -----------------------------------------------------------------------
1255
1256     CFG_RSA                     If defined, support for basic RSA
1257                                 encryption will be included.
1258     CFG_RSA_BITS                Indicates the number of bits used for
1259                                 RSA encryption keys.  To keep code size
1260                                 reasonable, RSA encryption is currently
1261                                 limited to using 64-bit or 32-bit numbers,
1262                                 with 64-bit providing higher security, and
1263                                 32-bit providing smaller encrypted text
1264                                 size.
1265
1266     NOTE:                       Please note that Printf can not be
1267                                 used to display 64-bit values (%lld)!
1268     -----------------------------------------------------------------------*/
1269     // #define CFG_RSA
1270     #define CFG_RSA_BITS                  (32)
1271 /*=========================================================================*/
1272
1273
1274
1275
1276 /*=========================================================================
1277   CONFIG FILE VALIDATION
1278   -------------------------------------------------------------------------
1279   Basic error checking to make sure that incompatible defines are not
1280   enabled at the same time, etc.
1281
1282   =========================================================================*/
1283
1284 #if !defined CFG_BRD_LPC1343_REFDESIGN && \
1285   !defined CFG_BRD_LPC1343_REFDESIGN_MINIMAL && \
1286   !defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB && \
1287   !defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART && \
1288   !defined CFG_BRD_LPC1343_802154USBSTICK && \
1289   !defined CFG_BRD_LPC1343_OLIMEX_P && \
1290   !defined CFG_BRD_LPC1343_LPCXPRESSO
1291   #error "You must defined a target board (CFG_BRD_LPC1343_REFDESIGN or CFG_BRD_LPC1343_REFDESIGN_MINIMAL or CFG_BRD_LPC1343_TFTLCDSTANDALONE or CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART or CFG_BRD_LPC1343_802154USBSTICK or CFG_BRD_LPC1343_LPCXPRESSO)"
1292 #endif
1293
1294 #if defined CFG_PRINTF_USBCDC && defined CFG_PRINTF_UART
1295   #error "CFG_PRINTF_UART or CFG_PRINTF_USBCDC cannot both be defined at once"
1296 #endif
1297
1298 #if defined CFG_PRINTF_USBCDC && !defined CFG_USBCDC
1299   #error "CFG_PRINTF_CDC requires CFG_USBCDC to be defined as well"
1300 #endif
1301
1302 #if defined CFG_USBCDC && defined CFG_USBHID
1303   #error "Only one USB class can be defined at a time (CFG_USBCDC or CFG_USBHID)"
1304 #endif
1305
1306 #if defined CFG_SSP0_SCKPIN_2_11 && defined CFG_SSP0_SCKPIN_0_6
1307   #error "Only one SCK pin can be defined at a time for SSP0"
1308 #endif
1309
1310 #if !defined CFG_SSP0_SCKPIN_2_11 && !defined CFG_SSP0_SCKPIN_0_6
1311   #error "An SCK pin must be selected for SSP0 (CFG_SSP0_SCKPIN_2_11 or CFG_SSP0_SCKPIN_0_6)"
1312 #endif
1313
1314 #ifdef CFG_INTERFACE
1315   #if !defined CFG_PRINTF_UART && !defined CFG_PRINTF_USBCDC
1316     #error "CFG_PRINTF_UART or CFG_PRINTF_USBCDC must be defined for for CFG_INTERFACE Input/Output"
1317   #endif
1318   #if defined CFG_PRINTF_USBCDC && CFG_INTERFACE_SILENTMODE == 1
1319     #error "CFG_INTERFACE_SILENTMODE typically isn't enabled with CFG_PRINTF_USBCDC"
1320   #endif
1321 #endif
1322
1323 #ifdef CFG_CHIBI
1324   #if !defined CFG_I2CEEPROM
1325     #error "CFG_CHIBI requires CFG_I2CEEPROM to store and retrieve addresses"
1326   #endif
1327   #ifdef CFG_SDCARD
1328     #error "CFG_CHIBI and CFG_SDCARD can not be defined at the same time. Only one SPI block is available on the LPC1343."
1329   #endif
1330   #ifdef CFG_TFTLCD
1331     #error "CFG_CHIBI and CFG_TFTLCD can not be defined at the same time since they both use pins 1.8, 1.9 and 1.10."
1332   #endif
1333   #ifdef CFG_PWM
1334     #error "CFG_CHIBI and CFG_PWM can not be defined at the same time since they both use pin 1.9."
1335   #endif
1336   #if CFG_CHIBI_PROMISCUOUS != 0 && CFG_CHIBI_PROMISCUOUS != 1
1337     #error "CFG_CHIBI_PROMISCUOUS must be equal to either 1 or 0"
1338   #endif
1339   #if !defined GPIO_ENABLE_IRQ1
1340     #error "GPIO_ENABLE_IRQ1 must be enabled when using Chibi (Chibi IRQ is on GPIO1.8)"
1341   #endif
1342 #endif
1343
1344 #ifdef CFG_TFTLCD
1345   #ifdef CFG_ST7565
1346     #error "CFG_TFTLCD and CFG_ST7565 can not be defined at the same time."
1347   #endif
1348   #ifdef CFG_SSD1306
1349     #error "CFG_TFTLCD and CFG_SSD1306 can not be defined at the same time."
1350   #endif
1351   #ifdef CFG_SHARPMEM
1352     #error "CFG_TFTLCD and CFG_SHARPMEM can not be defined at the same time."
1353   #endif
1354   #ifdef CFG_PWM
1355     #error "CFG_TFTLCD and CFG_PWM can not be defined at the same time since they both use pin 1.9."
1356   #endif
1357   #if !defined CFG_I2CEEPROM
1358     #error "CFG_TFTLCD requires CFG_I2CEEPROM to store and retrieve configuration settings"
1359   #endif
1360 #endif
1361
1362 #ifdef CFG_SDCARD
1363   #ifdef CFG_STEPPER
1364     #error  "CFG_SDCARD and CFG_STEPPER can not be defined at the same time since they both use pin 3.0."
1365   #endif
1366 #endif
1367
1368 #ifdef CFG_ST7565
1369   #ifdef CFG_SSD1306
1370     #error "CFG_ST7565 and CFG_SSD1306 can not be defined at the same time"
1371   #endif
1372 #endif
1373
1374 #ifdef CFG_RSA
1375   #if CFG_RSA_BITS != 64 && CFG_RSA_BITS != 32
1376     #error "CFG_RSA_BITS must be equal to either 32 or 64."
1377   #endif
1378 #endif
1379
1380 #if ADC_AVERAGING_ENABLE && ADC_AVERAGING_SAMPLES < 1
1381   #error "ADC_AVERAGING_SAMPLES must be 1 or higher when ADC averaging is enabled"
1382 #endif
1383
1384 #endif