implement SIOCSIWENCODE in wlcompat
[openwrt.git] / openwrt / docs / hardware / linksys / wrt54gs_v10 / nvram.txt
1 aa0=3
2 ag0=255
3 boardflags2=0
4 boardflags=0x0388
5 boardnum=42
6 boardrev=0x10
7 boardtype=0x0101
8 boot_ver=v3.2
9 boot_wait=yes
10 ccode=0
11 cctl=0
12 clkfreq=200
13 dl_ram_addr=a0001000
14 et0macaddr=00:0F:66:C8:74:44
15 et0mdcport=0
16 et0phyaddr=30
17 gpio2=adm_eecs
18 gpio3=adm_eesk
19 gpio5=adm_eedi
20 gpio6=adm_rc
21 il0macaddr=00:0f:66:c8:74:46
22 lan_ipaddr=192.168.1.1
23 lan_netmask=255.255.255.0
24 os_flash_addr=bfc40000
25 os_ram_addr=80001000
26 pa0b0=0x170c
27 pa0b1=0xfa24
28 pa0b2=0xfe70
29 pa0itssit=62
30 pa0maxpwr=0x48
31 pmon_ver=CFE 3.61.13.0
32 scratch=a0180000
33 sdram_config=0x0022
34 sdram_init=0x0008
35 sdram_ncdl=0x24
36 sdram_refresh=0x0000
37 sromrev=2
38 vlan0hwname=et0
39 vlan0ports=1 2 3 4 5*
40 vlan1hwname=et0
41 vlan1ports=0 5
42 watchdog=5000
43 wl0_active_mac=
44 wl0_afterburner=auto
45 wl0_antdiv=-1
46 wl0_ap_ip=
47 wl0_ap_isolate=0
48 wl0_ap_ssid=
49 wl0_auth=0
50 wl0_auth_mode=open
51 wl0_bcn=100
52 wl0_channel=6
53 wl0_closed=0
54 wl0_corerev=7
55 wl0_country=Worldwide
56 wl0_country_code=AU
57 wl0_crypto=tkip
58 wl0_dtim=1
59 wl0_frag=2346
60 wl0_frameburst=on
61 wl0_gmode=6
62 wl0_gmode_protection=off
63 wl0_hwaddr=00:0F:66:C8:74:46
64 wl0_ifname=eth1
65 wl0_infra=1
66 wl0_key1=
67 wl0_key2=
68 wl0_key3=
69 wl0_key4=
70 wl0_key=1
71 wl0_lazywds=1
72 wl0_mac_deny=
73 wl0_mac_list=
74 wl0_maclist=
75 wl0_macmode1=disabled
76 wl0_macmode=disabled
77 wl0_mode=ap
78 wl0_mrate=0
79 wl0_net_mode=mixed
80 wl0_passphrase=
81 wl0_phytype=g
82 wl0_phytypes=g
83 wl0_plcphdr=long
84 wl0_radio=1
85 wl0_radioids=BCM2050
86 wl0_radius_ipaddr=
87 wl0_radius_key=
88 wl0_radius_port=1812
89 wl0_rate=0
90 wl0_rateset=default
91 wl0_rts=2347
92 wl0_ssid=linksys
93 wl0_unit=0
94 wl0_wds=
95 wl0_wep=disabled
96 wl0_wep_bit=64
97 wl0_wep_buf=
98 wl0_wep_gen=
99 wl0_wep_last=
100 wl0_wpa_gtk_rekey=3600
101 wl0_wpa_psk=
102 wl0gpio2=0
103 wl0gpio3=0
104 wl0id=0x4320
105 wl_country_code=AU
This page took 0.048833 seconds and 5 git commands to generate.