* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
*
- * $Id$
*/
#include <linux/module.h>
#include <linux/pci.h>
enum {
/* Linksys */
WAP54GV1,
+ WAP54GV2,
WAP54GV3,
WRT54GV1,
WRT54G,
WRTSL54GS,
WRT54G3G,
+ WRT160N,
+ WRT300NV11,
WRT350N,
WRT600N,
WRT600NV11,
+ WRT610N,
/* ASUS */
WLHDD,
/* D-Link */
DIR130,
+ DIR320,
DIR330,
DWL3150,
/* Sitecom */
WL105B,
+
+ /* Western Digital */
+ WDNetCenter,
+
+ /* Askey */
+ RT210W,
+
+ /* OvisLink */
+ WL1600GL,
};
static void __init bcm4780_init(void) {
schedule_timeout(HZ * 5);
}
+static void __init NetCenter_init(void) {
+ /* unset pin 6 (+12V) */
+ int pin = 1 << 6;
+ gpio_outen(pin, pin);
+ gpio_control(pin, 0);
+ gpio_out(pin, pin);
+ /* unset pin 1 (turn off red led, blue will light alone if +5V comes up) */
+ pin = 1 << 1;
+ gpio_outen(pin, pin);
+ gpio_control(pin, 0);
+ gpio_out(pin, pin);
+ /* unset pin 3 (+5V) and wait 5 seconds (harddisk spin up) */
+ bcm4780_init();
+}
+
static void __init bcm57xx_init(void) {
int pin = 1 << 2;
{ .name = "wlan", .gpio = 1 << 4 },
},
},
+ [WAP54GV2] = {
+ .name = "Linksys WAP54G V2",
+ .buttons = {
+ { .name = "reset", .gpio = 1 << 0 },
+ },
+ .leds = {
+ { .name = "wlan", .gpio = 1 << 5, .polarity = REVERSE },
+ /* GPIO 6 is b44 (eth0, LAN) PHY power */
+ },
+ },
[WAP54GV3] = {
.name = "Linksys WAP54G V3",
.buttons = {
{ .name = "3g_blink", .gpio = 1 << 5, .polarity = NORMAL },
},
},
+ [WRT160N] = {
+ .name = "Linksys WRT160N",
+ .buttons = {
+ { .name = "reset", .gpio = 1 << 6 },
+ { .name = "ses", .gpio = 1 << 4 },
+ },
+ .leds = {
+ { .name = "power", .gpio = 1 << 1, .polarity = NORMAL },
+ { .name = "ses_blue", .gpio = 1 << 5, .polarity = REVERSE },
+ { .name = "ses_orange", .gpio = 1 << 3, .polarity = REVERSE },
+ },
+ },
+ [WRT300NV11] = {
+ .name = "Linksys WRT300N V1.1",
+ .buttons = {
+ { .name = "reset", .gpio = 1 << 6 }, // "Reset" on back panel
+ { .name = "ses", .gpio = 1 << 4 }, // "Reserved" on top panel
+ },
+ .leds = {
+ { .name = "power", .gpio = 1 << 1, .polarity = NORMAL }, // "Power"
+ { .name = "ses_amber", .gpio = 1 << 3, .polarity = REVERSE }, // "Security" Amber
+ { .name = "ses_green", .gpio = 1 << 5, .polarity = REVERSE }, // "Security" Green
+ },
+ .platform_init = bcm57xx_init,
+ },
[WRT350N] = {
.name = "Linksys WRT350N",
.buttons = {
},
.platform_init = bcm57xx_init,
},
+ [WRT610N] = {
+ .name = "Linksys WRT610N",
+ .buttons = {
+ { .name = "reset", .gpio = 1 << 6 },
+ { .name = "ses", .gpio = 1 << 8 },
+ },
+ .leds = {
+ { .name = "power", .gpio = 1 << 1, .polarity = NORMAL }, // Power LED
+ { .name = "usb", .gpio = 1 << 0, .polarity = REVERSE }, // USB LED
+ { .name = "ses_amber", .gpio = 1 << 3, .polarity = REVERSE }, // WiFi protected setup LED amber
+ { .name = "ses_blue", .gpio = 1 << 9, .polarity = REVERSE }, // WiFi protected setup LED blue
+ },
+ },
/* Asus */
[WLHDD] = {
.name = "ASUS WL-HDD",
{ .name = "blue", .gpio = 1 << 6},
},
},
+ [DIR320] = {
+ .name = "D-Link DIR-320",
+ .buttons = {
+ { .name = "reserved", .gpio = 1 << 6},
+ { .name = "reset", .gpio = 1 << 7},
+ },
+ .leds = {
+ { .name = "wlan", .gpio = 1 << 0, .polarity = NORMAL },
+ { .name = "diag", .gpio = 1 << 1, .polarity = NORMAL }, /* "status led */
+ { .name = "red", .gpio = 1 << 3, .polarity = REVERSE },
+ { .name = "blue", .gpio = 1 << 4, .polarity = REVERSE },
+ { .name = "usb", .gpio = 1 << 5, .polarity = NORMAL },
+ },
+ },
[DIR330] = {
.name = "D-Link DIR-330",
.buttons = {
{ .name = "power", .gpio = 1 << 3},
},
},
+ /* Western Digital Net Center */
+ [WDNetCenter] = {
+ .name = "Western Digital NetCenter",
+ .buttons = {
+ { .name = "power", .gpio = 1 << 0},
+ { .name = "reset", .gpio = 1 << 7},
+ },
+ .platform_init = NetCenter_init,
+ },
+ /* Askey (and clones) */
+ [RT210W] = {
+ .name = "Askey RT210W",
+ .buttons = {
+ /* Power button is hard-wired to hardware reset */
+ /* but is also connected to GPIO 7 (probably for bootloader recovery) */
+ { .name = "power", .gpio = 1 << 7},
+ },
+ .leds = {
+ /* These were verified and named based on Belkin F5D4230-4 v1112 */
+ { .name = "connected", .gpio = 1 << 0, .polarity = REVERSE },
+ { .name = "wlan", .gpio = 1 << 3, .polarity = REVERSE },
+ { .name = "power", .gpio = 1 << 5, .polarity = REVERSE },
+ },
+ },
+ [WL1600GL] = {
+ .name = "OvisLink WL-1600GL",
+ .buttons = {
+ { .name = "reset", .gpio = 1 << 3 },
+ { .name = "ses", .gpio = 1 << 4 },
+ },
+ .leds = {
+ { .name = "power", .gpio = 1 << 5, .polarity = REVERSE },
+ { .name = "wps", .gpio = 1 << 2, .polarity = REVERSE },
+ { .name = "wlan", .gpio = 1 << 1, .polarity = REVERSE },
+ { .name = "connected", .gpio = 1 << 0, .polarity = REVERSE },
+ },
+ },
};
static struct platform_t __init *platform_detect(void)
return &platforms[DIR330];
}
+ /* Based on "wsc_modelname */
+ if ((buf = nvram_get("wsc_modelname"))) {
+ if (!strcmp(buf, "WRT610N"))
+ return &platforms[WRT610N];
+ }
+
/* Based on "model_no" */
if ((buf = nvram_get("model_no"))) {
if (startswith(buf,"WL700")) /* WL700* */
if ((buf = nvram_get("ModelId"))) {
if (!strcmp(buf, "WR850GP"))
return &platforms[WR850GP];
+ if (!strcmp(buf, "WR850G"))
+ return &platforms[WR850GV2V3];
if (!strcmp(buf, "WX-5565") && !strcmp(getvar("boardtype"),"bcm94710ap"))
return &platforms[TM2300]; /* Dell TrueMobile 2300 */
if (startswith(buf,"WE800G")) /* WE800G* */
if (startswith(getvar("pmon_ver"), "CFE")) {
/* CFE based - newer hardware */
if (!strcmp(boardnum, "42")) { /* Linksys */
+ if (!strcmp(boardtype, "0x478") && !strcmp(getvar("boot_hw_model"), "WRT300N") && !strcmp(getvar("boot_hw_ver"), "1.1"))
+ return &platforms[WRT300NV11];
+
if (!strcmp(boardtype, "0x478") && !strcmp(getvar("cardbus"), "1"))
return &platforms[WRT350N];
if (!strcmp(getvar("et1phyaddr"),"5") && !strcmp(getvar("et1mdcport"), "1"))
return &platforms[WRTSL54GS];
+ if (!strcmp(boardtype, "0x0472"))
+ return &platforms[WRT160N];
+
/* default to WRT54G */
return &platforms[WRT54G];
}
+ if (!strcmp(boardnum, "1024") && !strcmp(boardtype, "0x0446"))
+ return &platforms[WAP54GV2];
+
+ if (!strcmp(boardnum, "8") && !strcmp(boardtype, "0x048e"))
+ return &platforms[WL1600GL];
+
if (!strcmp(boardnum, "44") || !strcmp(boardnum, "44\r")) {
if (!strcmp(boardtype,"0x0101") || !strcmp(boardtype, "0x0101\r"))
if (!strcmp(getvar("boardtype"), "0x0101") && !strcmp(getvar("boardrev"), "0x10")) /* SE505V2 With Modified CFE */
return &platforms[SE505V2];
+ if (!strcmp(boardtype, "0x048e") && !strcmp(getvar("boardrev"),"0x35") &&
+ !strcmp(getvar("boardflags"), "0x750")) /* D-Link DIR-320 */
+ return &platforms[DIR320];
+
+ if (!strncmp(boardnum, "TH",2) && !strcmp(boardtype,"0x042f")) {
+ return &platforms[WDNetCenter];
+ }
+
} else { /* PMON based - old stuff */
if ((simple_strtoul(getvar("GemtekPmonVer"), NULL, 0) == 9) &&
(simple_strtoul(getvar("et0phyaddr"), NULL, 0) == 30)) {
/* unknown asus stuff, probably bcm4702 */
if (startswith(boardnum, "asusX"))
return &platforms[ASUS_4702];
+
+ /* bcm4702 based Askey RT210W clones, Including:
+ * Askey RT210W (duh?)
+ * Siemens SE505v1
+ * Belkin F5D7230-4 before version v1444 (MiniPCI slot, not integrated)
+ */
+ if (!strcmp(boardtype,"bcm94710r4")
+ && !strcmp(boardnum ,"100")
+ && !strcmp(getvar("pmon_ver"),"v1.03.12.bk")
+ ){
+ return &platforms[RT210W];
+ }
}
if (buf || !strcmp(boardnum, "00")) {/* probably buffalo */
projects / openwrt.git / blobdiff