-Index: madwifi-trunk-r3314/ath/if_ath.c
-===================================================================
---- madwifi-trunk-r3314.orig/ath/if_ath.c 2008-06-13 10:39:28.000000000 +0200
-+++ madwifi-trunk-r3314/ath/if_ath.c 2008-06-13 10:39:54.000000000 +0200
+--- a/ath/if_ath.c
++++ b/ath/if_ath.c
@@ -1014,9 +1014,7 @@
*/
sc->sc_hasveol = ath_hal_hasveol(ah);
return 0;
bad3:
ieee80211_ifdetach(ic);
-@@ -2347,16 +2350,6 @@
- }
- if (status & HAL_INT_MIB) {
- sc->sc_stats.ast_mib++;
-- /* When the card receives lots of PHY errors, the MIB
-- * interrupt will fire at a very rapid rate. We will use
-- * a timer to enforce at least 1 jiffy delay between
-- * MIB interrupts. This should be unproblematic, since
-- * the hardware will continue to update the counters in
-- * the mean time. */
-- sc->sc_imask &= ~HAL_INT_MIB;
-- ath_hal_intrset(ah, sc->sc_imask);
-- mod_timer(&sc->sc_mib_enable, jiffies + 1);
--
- /* Let the HAL handle the event. */
- ath_hal_mibevent(ah, &sc->sc_halstats);
- }
-@@ -2426,6 +2419,43 @@
+@@ -2428,6 +2431,43 @@
return flags;
}
/*
* Context: process context
*/
-@@ -2491,8 +2521,7 @@
+@@ -2493,8 +2533,7 @@
if (sc->sc_softled)
ath_hal_gpioCfgOutput(ah, sc->sc_ledpin);
/*
* This is needed only to setup initial state
-@@ -2528,7 +2557,7 @@
+@@ -2530,7 +2569,7 @@
* Enable MIB interrupts when there are hardware phy counters.
* Note we only do this (at the moment) for station mode.
*/
sc->sc_imask |= HAL_INT_MIB;
ath_hal_intrset(ah, sc->sc_imask);
-@@ -2785,9 +2814,7 @@
+@@ -2787,9 +2826,7 @@
EPRINTF(sc, "Unable to reset hardware: '%s' (HAL status %u)\n",
ath_get_hal_status_desc(status), status);
ath_update_txpow(sc); /* update tx power state */
ath_radar_update(sc);
ath_setdefantenna(sc, sc->sc_defant);
-@@ -4165,6 +4192,8 @@
+@@ -4174,6 +4211,8 @@
if (sc->sc_nmonvaps > 0)
rfilt |= (HAL_RX_FILTER_CONTROL | HAL_RX_FILTER_BEACON |
HAL_RX_FILTER_PROBEREQ | HAL_RX_FILTER_PROM);
if (sc->sc_curchan.privFlags & CHANNEL_DFS)
rfilt |= (HAL_RX_FILTER_PHYERR | HAL_RX_FILTER_PHYRADAR);
return rfilt;
-@@ -6513,9 +6542,6 @@
+@@ -6524,9 +6563,6 @@
rs->rs_rssi = 0;
len = rs->rs_datalen;
if (rs->rs_more) {
/*
-@@ -8865,9 +8891,7 @@
+@@ -8874,9 +8910,7 @@
if (sc->sc_softled)
ath_hal_gpioCfgOutput(ah, sc->sc_ledpin);
sc->sc_curchan = hchan;
ath_update_txpow(sc); /* update tx power state */
ath_radar_update(sc);
-@@ -10644,9 +10668,54 @@
+@@ -10653,9 +10687,54 @@
ATH_RP_IGNORED = 24,
ATH_RADAR_IGNORED = 25,
ATH_MAXVAPS = 26,
ATH_SYSCTL_DECL(ath_sysctl_halparam, ctl, write, filp, buffer, lenp, ppos)
{
struct ath_softc *sc = ctl->extra1;
-@@ -10832,6 +10901,11 @@
+@@ -10841,6 +10920,11 @@
case ATH_RADAR_IGNORED:
sc->sc_radar_ignored = val;
break;
default:
ret = -EINVAL;
break;
-@@ -10898,6 +10972,11 @@
+@@ -10907,6 +10991,11 @@
case ATH_RADAR_IGNORED:
val = sc->sc_radar_ignored;
break;
default:
ret = -EINVAL;
break;
-@@ -11075,6 +11154,24 @@
+@@ -11084,6 +11173,24 @@
.proc_handler = ath_sysctl_halparam,
.extra2 = (void *)ATH_RADAR_IGNORED,
},
{ 0 }
};
-Index: madwifi-trunk-r3314/ath/if_athvar.h
-===================================================================
---- madwifi-trunk-r3314.orig/ath/if_athvar.h 2008-06-13 10:39:28.000000000 +0200
-+++ madwifi-trunk-r3314/ath/if_athvar.h 2008-06-13 10:39:32.000000000 +0200
+--- a/ath/if_athvar.h
++++ b/ath/if_athvar.h
@@ -693,6 +693,10 @@
unsigned int sc_txcont_power; /* Continuous transmit power in 0.5dBm units */
unsigned int sc_txcont_rate; /* Continuous transmit rate in Mbps */
/* rate tables */
const HAL_RATE_TABLE *sc_rates[IEEE80211_MODE_MAX];
const HAL_RATE_TABLE *sc_currates; /* current rate table */
-Index: madwifi-trunk-r3314/ath/if_ath_hal.h
-===================================================================
---- madwifi-trunk-r3314.orig/ath/if_ath_hal.h 2008-06-13 10:39:26.000000000 +0200
-+++ madwifi-trunk-r3314/ath/if_ath_hal.h 2008-06-13 10:39:32.000000000 +0200
+--- a/ath/if_ath_hal.h
++++ b/ath/if_ath_hal.h
@@ -67,14 +67,14 @@
static inline HAL_BOOL ath_hal_getdiagstate(struct ath_hal *ah, int request,