-+
-+#include <asm/ar7/tnetd73xx.h>
-+
-+#define AVALANCHE_UART0_INT 7
-+#define AVALANCHE_UART1_INT 8
-+
-+#define MIPS_EXCEPTION_OFFSET 8
-+#define LNXINTNUM(x)((x) + MIPS_EXCEPTION_OFFSET)
-+
-+/*
-+ * AR7 board SDRAM base address. This is used to setup the
-+ * bootmem tables
-+ */
-+
-+#define AVALANCHE_SDRAM_BASE CONFIG_AR7_MEMORY//0x14000000UL
-+#define AVALANCHE_INTC_BASE TNETD73XX_INTC_BASE
-+
-+
-+/*
-+ * AR7 board vectors
-+ */
-+
-+#define AVALANCHE_VECS (KSEG1ADDR(AVALANCHE_SDRAM_BASE))
-+#define AVALANCHE_VECS_KSEG0 (KSEG0ADDR(AVALANCHE_SDRAM_BASE))
-+
-+
-+/*
-+ * Yamon Prom print address.
-+ */
-+#define AVALANCHE_YAMON_FUNCTION_BASE (KSEG1ADDR(0x10000500))
-+#define AVALANCHE_YAMON_PROM_PRINT_COUNT_ADDR (AVALANCHE_YAMON_FUNCTION_BASE + 0x4) /* print_count function */
-+#define AVALANCHE_YAMON_PROM_PRINT_ADDR (AVALANCHE_YAMON_FUNCTION_BASE + 0x34)
-+
-+/*
-+ * AR7 Reset and PSU standby register.
-+ */
-+#define AVALANCHE_SOFTRES_REG (KSEG1ADDR(0x08611600)) /* Resets machine */
-+#define AVALANCHE_PSUSTBY_REG (KSEG1ADDR(0x08611600)) /* Turns off power supply unit */
-+#define AVALANCHE_GORESET 0x1
-+#define AVALANCHE_GOSTBY 0x1
-+#define AVALANCHE_SWRCR (*(unsigned int *)TNETD73XX_RST_CTRL_SWRCR)
-+
-+/*
-+ * Avalanche UART register base.
-+ */
-+
-+#define AVALANCHE_UART0_REGS_BASE (KSEG1ADDR(0x08610E00)) /* AVALANCHE UART 0 */
-+#define AVALANCHE_UART1_REGS_BASE (KSEG1ADDR(0x08610F00)) /* AVALANCHE UART 1 */
-+#define AVALANCHE_BASE_BAUD ( 3686400 / 16 )
-+
-+/*
-+ * AVALANCHE DMA controller base
-+ */
-+
-+#define AVALANCHE_DMA0_CTRL_BASE (KSEG1ADDR(0x08611400)) /* DMA 0 (channels 0-3) */
-+
-+
-+
-+/*
-+ * GPIO register map
-+ */
-+
-+/* to be obtained from avalanche_map.h */
-+#define AVALANCHE_GPIO_WRITE_REG (KSEG1ADDR(0xa8610904))
-+#define AVALANCHE_GPIO_DIRECTION_REG (KSEG1ADDR(0xa8610908))
-+#define AVALANCHE_GPIO_MODE_REG (KSEG1ADDR(0xa861090C))
-+#define AVALANCHE_GPIO_PIN_COUNT 32
-+#define AVALANCHE_GPIO_OFF_MAP {0xF34FFFC0,0}
-+
-+
-+// Let us define board specific information here.
-+
-+#if defined(CONFIG_AR7DB)
-+
-+#define AFECLK_FREQ 35328000
-+#define REFCLK_FREQ 25000000
-+#define OSC3_FREQ 24000000
-+#define AVALANCHE_CPMAC_INTERNAL_PHY_MASK 0x80000000
-+#define AVALANCHE_CPMAC_EXTERNAL_PHY_MASK 0x55555555
-+
-+#endif
-+
-+
-+#if defined(CONFIG_AR7RD)
-+
-+#define AFECLK_FREQ 35328000
-+#define REFCLK_FREQ 25000000
-+#define OSC3_FREQ 24000000
-+#define AVALANCHE_CPMAC_INTERNAL_PHY_MASK 0x80000000
-+
-+#if defined(CONFIG_AR7_MARVELL)
-+#define AVALANCHE_CPMAC_EXTERNAL_PHY_MASK 0x00010000
-+#else
-+#define AVALANCHE_CPMAC_EXTERNAL_PHY_MASK 0x2
-+#endif
-+
-+#endif
-+
-+
-+#if defined(CONFIG_AR7WRD)
-+
-+#define AFECLK_FREQ 35328000
-+#define REFCLK_FREQ 25000000
-+#define OSC3_FREQ 24000000
-+#define AVALANCHE_CPMAC_INTERNAL_PHY_MASK 0x80000000
-+
-+#if defined(CONFIG_AR7_MARVELL)
-+#define AVALANCHE_CPMAC_EXTERNAL_PHY_MASK 0x00010000
-+#else
-+#define AVALANCHE_CPMAC_EXTERNAL_PHY_MASK 0x2
-+#endif
-+
-+#endif
-+
-+extern unsigned int tnetd73xx_vbus_freq;
-+#define AVALANCHE_VBUS_FREQ tnetd73xx_vbus_freq
-+
-+static inline unsigned int get_avalanche_vbus_freq(void)
-+{
-+ return (tnetd73xx_vbus_freq);
-+}
-+
-+#endif /*_MIPS_AR7_H */
-diff -urN linux.old/include/asm-mips/ar7/avalanche.h linux.dev/include/asm-mips/ar7/avalanche.h
---- linux.old/include/asm-mips/ar7/avalanche.h 1970-01-01 01:00:00.000000000 +0100
-+++ linux.dev/include/asm-mips/ar7/avalanche.h 2005-07-09 08:00:15.301024000 +0200
-@@ -0,0 +1,183 @@
-+/* $Id$
-+ *
-+ * avalanche.h
-+ *
-+ * Jeff Harrell, jharrell@ti.com
-+ * Copyright (C) 2000,2001,2002 Texas Instruments Inc.
-+ *
-+ *
-+ * ########################################################################
-+ *
-+ * This program is free software; you can distribute it and/or modify it
-+ * under the terms of the GNU General Public License (Version 2) as
-+ * published by the Free Software Foundation.
-+ *
-+ * This program is distributed in the hope it will be useful, but WITHOUT
-+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-+ * for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License along
-+ * with this program; if not, write to the Free Software Foundation, Inc.,
-+ * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-+ *
-+ * ########################################################################
-+ *
-+ * Defines of the AVALANCHE board specific address-MAP, registers, etc.
-+ *
-+ */
-+#ifndef _MIPS_AVALANCHE_H
-+#define _MIPS_AVALANCHE_H
-+
-+#include <asm/addrspace.h>
-+
-+/*
-+ * AVALANCHE board SDRAM base address. This is used to setup the
-+ * bootmem tables
-+ */
-+
-+#define AVALANCHE_SDRAM_BASE 0x14000000UL
-+
-+/*
-+ * AVALANCHE board vectors
-+ */
-+
-+#define AVALANCHE_VECS (KSEG1ADDR(AVALANCHE_SDRAM_BASE))
-+#define AVALANCHE_VECS_KSEG0 (KSEG0ADDR(AVALANCHE_SDRAM_BASE))
-+/*
-+ * Avalanche RTC-device indirect register access.
-+ */
-+
-+#define EVM3_RTC_ADR_REG (KSEG1ADDR(0x1f000800))
-+#define EVM3_RTC_DAT_REG (KSEG1ADDR(0x1f000808))
-+
-+/*
-+ * Evm3 interrupt controller register base (primary)
-+ */
-+
-+#define AVALANCHE_ICTRL_REGS_BASE (KSEG1ADDR(0x08612400))
-+
-+/*
-+ * Avalanche exception controller register base (secondary)
-+ */
-+#define AVALANCHE_ECTRL_REGS_BASE (AVALANCHE_ICTRL_REGS_BASE+0x80)
-+
-+
-+/*
-+ * Avalanche Interrupt Channel Control register base
-+ */
-+#define AVALANCHE_CHCTRL_REGS_BASE (AVALANCHE_ICTRL_REGS_BASE + 0x200)
-+
-+
-+/*
-+ * Avalanche UART register base.
-+ */
-+
-+#define AVALANCHE_UART0_REGS_BASE (KSEG1ADDR(0x08610E00)) /* AVALANCHE UART 0 */
-+#define AVALANCHE_UART1_REGS_BASE (KSEG1ADDR(0x08610F00)) /* AVALANCHE UART 1 */
-+#define AVALANCHE_BASE_BAUD ( 3686400 / 16 )
-+/*
-+ * AVALANCHE DMA controller base
-+ */
-+
-+#define AVALANCHE_DMA0_CTRL_BASE (KSEG1ADDR(0x08611400)) /* DMA 0 (channels 0-3) */
-+
-+
-+/*
-+ * AVALANCHE display register base.
-+ */
-+
-+#define EVM3_ASCII_DISPLAY_POS_BASE (KSEG1ADDR(0x1D000038))
-+#define EVM3_ASCII_DISPLAY_WORD_BASE (KSEG1ADDR(0x1D00003F)) /* How is this used??? JAH */
-+
-+
-+#define EVM3_ASCIIPOS0 0x1D000038
-+#define EVM3_ASCIIPOS1 0x1D000039
-+#define EVM3_ASCIIPOS2 0x1D00003A
-+#define EVM3_ASCIIPOS3 0x1D00003B
-+#define EVM3_ASCIIPOS4 0x1D00003C
-+#define EVM3_ASCIIPOS5 0x1D00003D
-+#define EVM3_ASCIIPOS6 0x1D00003E
-+#define EVM3_ASCIIPOS7 0x1D00003F
-+
-+/*
-+ * Yamon Prom print address.
-+ */
-+#define AVALANCHE_YAMON_FUNCTION_BASE (KSEG1ADDR(0x10000500))
-+#define AVALANCHE_YAMON_PROM_PRINT_COUNT_ADDR (AVALANCHE_YAMON_FUNCTION_BASE + 0x4) /* print_count function */
-+#define AVALANCHE_YAMON_PROM_PRINT_ADDR (AVALANCHE_YAMON_FUNCTION_BASE + 0x34)
-+
-+/*
-+ * Evm3 Reset and PSU standby register.
-+ */
-+#define AVALANCHE_SOFTRES_REG (KSEG1ADDR(0x08611600)) /* Resets machine */
-+#define AVALANCHE_PSUSTBY_REG (KSEG1ADDR(0x08611600)) /* Turns off power supply unit */
-+#define AVALANCHE_GORESET 0x1
-+#define AVALANCHE_GOSTBY 0x1
-+
-+/************************************************************************
-+ * PERIPHERAL BUS LEDs (P-LED):
-+*************************************************************************/
-+
-+/************************************************************************
-+ * P-LED Register Addresses
-+*************************************************************************/
-+
-+#define EVM3_PLED (KSEG1ADDR(0x01C500000)) /* 0x1D200000 P-LED */
-+
-+
-+/************************************************************************
-+ * Register field encodings
-+*************************************************************************/
-+
-+/******** reg: PLED ********/
-+/* bits 7:0: VAL */
-+#define EVM3_PLED_VAL_MSK 0xff
-+
-+/* bit 0: */
-+#define EVM3_PLED_BIT0_SHF 0
-+#define EVM3_PLED_BIT0_MSK (1 << EVM3_PLED_BIT0_SHF)
-+#define EVM3_PLED_BIT0_ON EVM3_PLED_BIT0_MSK
-+
-+/* bit 1: */
-+#define EVM3_PLED_BIT1_SHF 1
-+#define EVM3_PLED_BIT1_MSK (1 << EVM3_PLED_BIT1_SHF)
-+#define EVM3_PLED_BIT1_ON EVM3_PLED_BIT1_MSK
-+
-+/* bit 2: */
-+#define EVM3_PLED_BIT2_SHF 2
-+#define EVM3_PLED_BIT2_MSK (1 << EVM3_PLED_BIT2_SHF)
-+#define EVM3_PLED_BIT2_ON EVM3_PLED_BIT2_MSK
-+
-+/* bit 3: */
-+#define EVM3_PLED_BIT3_SHF 3
-+#define EVM3_PLED_BIT3_MSK (1 << EVM3_PLED_BIT3_SHF)
-+#define EVM3_PLED_BIT3_ON EVM3_PLED_BIT3_MSK
-+
-+/* bit 4: */
-+#define EVM3_PLED_BIT4_SHF 4
-+#define EVM3_PLED_BIT4_MSK (1 << EVM3_PLED_BIT4_SHF)
-+#define EVM3_PLED_BIT4_ON EVM3_PLED_BIT4_MSK
-+
-+/* bit 5: */
-+#define EVM3_PLED_BIT5_SHF 5
-+#define EVM3_PLED_BIT5_MSK (1 << EVM3_PLED_BIT5_SHF)
-+#define EVM3_PLED_BIT5_ON EVM3_PLED_BIT5_MSK
-+
-+/* bit 6: */
-+#define EVM3_PLED_BIT6_SHF 6
-+#define EVM3_PLED_BIT6_MSK (1 << EVM3_PLED_BIT6_SHF)
-+#define EVM3_PLED_BIT6_ON EVM3_PLED_BIT6_MSK
-+
-+/* bit 7: */
-+#define EVM3_PLED_BIT7_SHF 7
-+#define EVM3_PLED_BIT7_MSK (1 << EVM3_PLED_BIT7_SHF)
-+#define EVM3_PLED_BIT7_ON EVM3_PLED_BIT7_MSK
-+
-+#endif /* !(_MIPS_AVALANCHE_H) */
-+
-+
-+
-+
-+
-+
projects / openwrt.git / blobdiff