ath5k: do not stop the hardware queues during PAPD calibration, speeds up calibration

[openwrt.git] / package / mac80211 / patches / 800-b43-gpio-mask-module-option.patch

diff --git a/package/mac80211/patches/800-b43-gpio-mask-module-option.patch b/package/mac80211/patches/800-b43-gpio-mask-module-option.patch
index d61e11a..f3c278e 100644 (file)
--- a/package/mac80211/patches/800-b43-gpio-mask-module-option.patch
+++ b/package/mac80211/patches/800-b43-gpio-mask-module-option.patch
@@ -1,6 +1,6 @@
 --- a/drivers/net/wireless/b43/b43.h
 +++ b/drivers/net/wireless/b43/b43.h
-@@ -746,6 +746,7 @@ struct b43_wldev {
+@@ -803,6 +803,7 @@ struct b43_wldev {
        bool qos_enabled;               /* TRUE, if QoS is used. */
        bool hwcrypto_enabled;          /* TRUE, if HW crypto acceleration is enabled. */
        bool use_pio;                   /* TRUE if next init should use PIO */
@@ -10,7 +10,7 @@
        struct b43_phy phy;
 --- a/drivers/net/wireless/b43/main.c
 +++ b/drivers/net/wireless/b43/main.c
-@@ -75,6 +75,11 @@ MODULE_FIRMWARE("b43/ucode16_mimo.fw");
+@@ -76,6 +76,11 @@ MODULE_FIRMWARE("b43/ucode16_mimo.fw");
  MODULE_FIRMWARE("b43/ucode5.fw");
  MODULE_FIRMWARE("b43/ucode9.fw");
  
@@ -22,12 +22,12 @@
  static int modparam_bad_frames_preempt;
  module_param_named(bad_frames_preempt, modparam_bad_frames_preempt, int, 0444);
  MODULE_PARM_DESC(bad_frames_preempt,
-@@ -2671,10 +2676,10 @@ static int b43_gpio_init(struct b43_wlde
-                   & ~B43_MACCTL_GPOUTSMSK);
+@@ -2674,10 +2679,10 @@ static int b43_gpio_init(struct b43_wlde
+       u32 mask, set;
  
-       b43_write16(dev, B43_MMIO_GPIO_MASK, b43_read16(dev, B43_MMIO_GPIO_MASK)
--                  | 0x000F);
-+                  | modparam_gpiomask);
+       b43_maskset32(dev, B43_MMIO_MACCTL, ~B43_MACCTL_GPOUTSMSK, 0);
+-      b43_maskset16(dev, B43_MMIO_GPIO_MASK, ~0, 0xF);
++      b43_maskset16(dev, B43_MMIO_GPIO_MASK, ~0, modparam_gpiomask);
  
        mask = 0x0000001F;
 -      set = 0x0000000F;
@@ -35,16 +35,3 @@
        if (dev->dev->chip_id == 0x4301) {
                mask |= 0x0060;
                set |= 0x0060;
-@@ -5441,10 +5446,10 @@ static void b43_print_driverinfo(void)
-       feat_sdio = "S";
- #endif
-       printk(KERN_INFO "Broadcom 43xx driver loaded "
--             "[ Features: %s%s%s%s%s, Firmware-ID: "
-+             "[ Features: %s%s%s%s%s, GPIO LED Mask: 0x%04x, Firmware-ID: "
-              B43_SUPPORTED_FIRMWARE_ID " ]\n",
-              feat_pci, feat_pcmcia, feat_nphy,
--             feat_leds, feat_sdio);
-+             feat_leds, feat_sdio, modparam_gpiomask);
- }
- 
- static int __init b43_init(void)