* jtag, 0/1/2 uarts, clock frequency control, a watchdog interrupt timer,
* gpio interface, extbus, and support for serial and parallel flashes.
*
- * $Id: sbchipc.h,v 1.1.1.14 2006/04/15 01:29:08 michael Exp $
- * Copyright 2006, Broadcom Corporation
+ * Copyright 2007, Broadcom Corporation
* All Rights Reserved.
*
* THIS SOFTWARE IS OFFERED "AS IS", AND BROADCOM GRANTS NO WARRANTIES OF ANY
#ifndef _SBCHIPC_H
#define _SBCHIPC_H
-
#ifndef _LANGUAGE_ASSEMBLY
/* cpp contortions to concatenate w/arg prescan */
#define PAD _XSTR(__LINE__)
#endif /* PAD */
+
typedef volatile struct {
uint32 chipid; /* 0x0 */
uint32 capabilities;
/* Silicon backplane configuration broadcast control */
uint32 broadcastaddress; /* 0x50 */
uint32 broadcastdata;
- uint32 PAD[2];
/* gpio - cleared only by power-on-reset */
+ uint32 gpiopullup; /* 0x58, corerev >= 20 */
+ uint32 gpiopulldown; /* 0x5c, corerev >= 20 */
uint32 gpioin; /* 0x60 */
uint32 gpioout;
uint32 gpioouten;
uint32 gpiocontrol;
uint32 gpiointpolarity;
uint32 gpiointmask;
- uint32 PAD[2];
+
+ /* GPIO events corerev >= 11 */
+ uint32 gpioevent;
+ uint32 gpioeventintmask;
/* Watchdog timer */
uint32 watchdog; /* 0x80 */
- uint32 PAD[1];
+
+ /* GPIO events corerev >= 11 */
+ uint32 gpioeventintpolarity;
/* GPIO based LED powersave registers corerev >= 16 */
uint32 gpiotimerval; /* 0x88 */
uint32 prog_waitcount;
uint32 flash_config;
uint32 flash_waitcount;
- uint32 PAD[44];
-
- /* Clock control and hardware workarounds */
- uint32 clk_ctl_st;
+ uint32 PAD[4];
+
+ /* Enhanced Coexistance Interface (ECI) registers (corerev >= 21) */
+ uint32 eci_output; /* 0x140 */
+ uint32 eci_control;
+ uint32 eci_inputlo;
+ uint32 eci_inputmi;
+ uint32 eci_inputhi;
+ uint32 eci_inputintpolaritylo;
+ uint32 eci_inputintpolaritymi;
+ uint32 eci_inputintpolarityhi;
+ uint32 eci_intmasklo;
+ uint32 eci_intmaskmi;
+ uint32 eci_intmaskhi;
+ uint32 eci_eventlo;
+ uint32 eci_eventmi;
+ uint32 eci_eventhi;
+ uint32 eci_eventmasklo;
+ uint32 eci_eventmaskmi;
+ uint32 eci_eventmaskhi;
+ uint32 PAD[23];
+
+
+ /* Clock control and hardware workarounds (corerev >= 20) */
+ uint32 clk_ctl_st; /* 0x1e0 */
uint32 hw_war;
uint32 PAD[70];
uint8 uart1lsr;
uint8 uart1msr;
uint8 uart1scratch;
+ uint32 PAD[126];
+
+ /* PMU registers (corerev >= 20) */
+ uint32 pmucontrol; /* 0x600 */
+ uint32 pmucapabilities;
+ uint32 pmustatus;
+ uint32 res_state;
+ uint32 res_pending;
+ uint32 pmutimer;
+ uint32 min_res_mask;
+ uint32 max_res_mask;
+ uint32 res_table_sel;
+ uint32 res_dep_mask;
+ uint32 res_updn_timer;
+ uint32 res_timer;
+ uint32 clkstretch;
+ uint32 pmuwatchdog;
+ uint32 PAD[2];
+ uint32 res_req_timer_sel;
+ uint32 res_req_timer;
+ uint32 res_req_mask;
+ uint32 PAD;
+ uint32 chipcontrol_addr;
+ uint32 chipcontrol_data;
+ uint32 regcontrol_addr;
+ uint32 regcontrol_data;
+ uint32 pllcontrol_addr;
+ uint32 pllcontrol_data;
+ uint32 PAD[102];
+ uint16 otp[512];
} chipcregs_t;
#endif /* _LANGUAGE_ASSEMBLY */
+/* corecontrol */
+#define CC_UE (1 << 0) /* uart enable */
+
#define CC_CHIPID 0
#define CC_CAPABILITIES 4
+#define CC_OTPST 0x10
+#define CC_CHIPST 0x2c
#define CC_JTAGCMD 0x30
#define CC_JTAGIR 0x34
#define CC_JTAGDR 0x38
#define CC_CLKC_M3 0xa0
#define CC_CLKDIV 0xa4
#define CC_SYS_CLK_CTL 0xc0
-#define CC_OTP 0x800
+#define CC_CLK_CTL_ST SB_CLK_CTL_ST
+#define PMU_CTL 0x600
+#define PMU_CAP 0x604
+#define PMU_ST 0x608
+#define PMU_TIMER 0x614
+#define PMU_MIN_RES_MASK 0x618
+#define PMU_MAX_RES_MASK 0x61c
+#define PMU_REG_CONTROL_ADDR 0x658
+#define PMU_REG_CONTROL_DATA 0x65C
+#define PMU_PLL_CONTROL_ADDR 0x660
+#define PMU_PLL_CONTROL_DATA 0x664
+#define CC_OTP 0x800 /* OTP address space */
/* chipid */
#define CID_ID_MASK 0x0000ffff /* Chip Id mask */
#define CID_CC_SHIFT 24
/* capabilities */
-#define CAP_UARTS_MASK 0x00000003 /* Number of uarts */
-#define CAP_MIPSEB 0x00000004 /* MIPS is in big-endian mode */
-#define CAP_UCLKSEL 0x00000018 /* UARTs clock select */
-#define CAP_UINTCLK 0x00000008 /* UARTs are driven by internal divided clock */
-#define CAP_UARTGPIO 0x00000020 /* UARTs own Gpio's 15:12 */
-#define CAP_EXTBUS_MASK 0x000000c0 /* External bus mask */
-#define CAP_EXTBUS_NONE 0x00000000 /* No ExtBus present */
-#define CAP_EXTBUS_FULL 0x00000040 /* ExtBus: PCMCIA, IDE & Prog */
-#define CAP_EXTBUS_PROG 0x00000080 /* ExtBus: ProgIf only */
-#define CAP_FLASH_MASK 0x00000700 /* Type of flash */
-#define CAP_PLL_MASK 0x00038000 /* Type of PLL */
-#define CAP_PWR_CTL 0x00040000 /* Power control */
-#define CAP_OTPSIZE 0x00380000 /* OTP Size (0 = none) */
-#define CAP_OTPSIZE_SHIFT 19 /* OTP Size shift */
-#define CAP_OTPSIZE_BASE 5 /* OTP Size base */
-#define CAP_JTAGP 0x00400000 /* JTAG Master Present */
-#define CAP_ROM 0x00800000 /* Internal boot rom active */
-#define CAP_BKPLN64 0x08000000 /* 64-bit backplane */
+#define CC_CAP_UARTS_MASK 0x00000003 /* Number of uarts */
+#define CC_CAP_MIPSEB 0x00000004 /* MIPS is in big-endian mode */
+#define CC_CAP_UCLKSEL 0x00000018 /* UARTs clock select */
+#define CC_CAP_UINTCLK 0x00000008 /* UARTs are driven by internal divided clock */
+#define CC_CAP_UARTGPIO 0x00000020 /* UARTs own Gpio's 15:12 */
+#define CC_CAP_EXTBUS_MASK 0x000000c0 /* External bus mask */
+#define CC_CAP_EXTBUS_NONE 0x00000000 /* No ExtBus present */
+#define CC_CAP_EXTBUS_FULL 0x00000040 /* ExtBus: PCMCIA, IDE & Prog */
+#define CC_CAP_EXTBUS_PROG 0x00000080 /* ExtBus: ProgIf only */
+#define CC_CAP_FLASH_MASK 0x00000700 /* Type of flash */
+#define CC_CAP_PLL_MASK 0x00038000 /* Type of PLL */
+#define CC_CAP_PWR_CTL 0x00040000 /* Power control */
+#define CC_CAP_OTPSIZE 0x00380000 /* OTP Size (0 = none) */
+#define CC_CAP_OTPSIZE_SHIFT 19 /* OTP Size shift */
+#define CC_CAP_OTPSIZE_BASE 5 /* OTP Size base */
+#define CC_CAP_JTAGP 0x00400000 /* JTAG Master Present */
+#define CC_CAP_ROM 0x00800000 /* Internal boot rom active */
+#define CC_CAP_BKPLN64 0x08000000 /* 64-bit backplane */
+#define CC_CAP_PMU 0x10000000 /* PMU Present, rev >= 20 */
+#define CC_CAP_ECI 0x20000000 /* ECI Present, rev >= 21 */
/* PLL type */
#define PLL_NONE 0x00000000
#define PLL_TYPE6 0x00028000 /* 100/200 or 120/240 only */
#define PLL_TYPE7 0x00038000 /* 25Mhz, 4 dividers */
+/* ALP clock on pre-PMU chips */
+#define ALP_CLOCK 20000000
+
+/* HT clock */
+#define HT_CLOCK 80000000
+
+/* watchdog clock */
+#define WATCHDOG_CLOCK_5354 32000 /* Hz */
+
/* corecontrol */
#define CC_UARTCLKO 0x00000001 /* Drive UART with internal clock */
#define CC_SE 0x00000002 /* sync clk out enable (corerev >= 3) */
+#define CC_UARTCLKEN 0x00000008 /* enable UART Clock (corerev > = 21 */
/* chipcontrol */
#define CHIPCTRL_4321A0_DEFAULT 0x3a4
#define CHIPCTRL_4321A1_DEFAULT 0x0a4
-/* Fields in the otpstatus register */
-#define OTPS_PROGFAIL 0x80000000
-#define OTPS_PROTECT 0x00000007
-#define OTPS_HW_PROTECT 0x00000001
-#define OTPS_SW_PROTECT 0x00000002
-#define OTPS_CID_PROTECT 0x00000004
-
-/* Fields in the otpcontrol register */
-#define OTPC_RECWAIT 0xff000000
-#define OTPC_PROGWAIT 0x00ffff00
-#define OTPC_PRW_SHIFT 8
-#define OTPC_MAXFAIL 0x00000038
-#define OTPC_VSEL 0x00000006
-#define OTPC_SELVL 0x00000001
-
-/* Fields in otpprog */
-#define OTPP_COL_MASK 0x000000ff
-#define OTPP_ROW_MASK 0x0000ff00
-#define OTPP_ROW_SHIFT 8
-#define OTPP_READERR 0x10000000
-#define OTPP_VALUE 0x20000000
-#define OTPP_VALUE_SHIFT 29
-#define OTPP_READ 0x40000000
-#define OTPP_START 0x80000000
-#define OTPP_BUSY 0x80000000
+/* Fields in the otpstatus register in rev >= 21 */
+#define OTPS_OL_MASK 0x000000ff
+#define OTPS_OL_MFG 0x00000001 /* manuf row is locked */
+#define OTPS_OL_OR1 0x00000002 /* otp redundancy row 1 is locked */
+#define OTPS_OL_OR2 0x00000004 /* otp redundancy row 2 is locked */
+#define OTPS_OL_GU 0x00000008 /* general use region is locked */
+#define OTPS_GUP_MASK 0x00000f00
+#define OTPS_GUP_SHIFT 8
+#define OTPS_GUP_HW 0x00000100 /* h/w subregion is programmed */
+#define OTPS_GUP_SW 0x00000200 /* s/w subregion is programmed */
+#define OTPS_GUP_CI 0x00000400 /* chipid/pkgopt subregion is programmed */
+#define OTPS_GUP_FUSE 0x00000800 /* fuse subregion is programmed */
+#define OTPS_READY 0x00001000
+#define OTPS_RV(x) (1 << (16 + (x)))
+
+/* Fields in the otpcontrol register in rev >= 21 */
+#define OTPC_PROGSEL 0x00000001
+#define OTPC_PCOUNT_MASK 0x0000000e
+#define OTPC_PCOUNT_SHIFT 1
+#define OTPC_VSEL_MASK 0x000000f0
+#define OTPC_VSEL_SHIFT 4
+#define OTPC_TMM_MASK 0x00000700
+#define OTPC_TMM_SHIFT 8
+#define OTPC_ODM 0x00000800
+#define OTPC_PROGEN 0x80000000
+
+/* Fields in otpprog in rev >= 21 */
+#define OTPP_COL_MASK 0x000000ff
+#define OTPP_COL_SHIFT 0
+#define OTPP_ROW_MASK 0x0000ff00
+#define OTPP_ROW_SHIFT 8
+#define OTPP_OC_MASK 0x0f000000
+#define OTPP_OC_SHIFT 24
+#define OTPP_READERR 0x10000000
+#define OTPP_VALUE_MASK 0x20000000
+#define OTPP_VALUE_SHIFT 29
+#define OTPP_START_BUSY 0x80000000
+
+/* Opcodes for OTPP_OC field */
+#define OTPPOC_READ 0
+#define OTPPOC_BIT_PROG 1
+#define OTPPOC_VERIFY 3
+#define OTPPOC_INIT 4
+#define OTPPOC_SET 5
+#define OTPPOC_RESET 6
+#define OTPPOC_OCST 7
+#define OTPPOC_ROW_LOCK 8
+#define OTPPOC_PRESCN_TEST 9
/* jtagcmd */
#define JCMD_START 0x80000000
/* intstatus/intmask */
#define CI_GPIO 0x00000001 /* gpio intr */
-#define CI_EI 0x00000002 /* ro: ext intr pin (corerev >= 3) */
+#define CI_EI 0x00000002 /* extif intr (corerev >= 3) */
+#define CI_TEMP 0x00000004 /* temp. ctrl intr (corerev >= 15) */
+#define CI_SIRQ 0x00000008 /* serial IRQ intr (corerev >= 15) */
+#define CI_ECI 0x00000010 /* eci intr (corerev >= 21) */
+#define CI_PMU 0x00000020 /* pmu intr (corerev >= 21) */
+#define CI_UART 0x00000040 /* uart intr (corerev >= 21) */
#define CI_WDRESET 0x80000000 /* watchdog reset occurred */
/* slow_clk_ctl */
#define SYCC_CD_MASK 0xffff0000 /* ClkDiv (ILP = 1/(4 * (divisor + 1)) */
#define SYCC_CD_SHIFT 16
+/* pcmcia_iowait */
+#define PI_W0_MASK 0x0000003f /* waitcount0 */
+#define PI_W1_MASK 0x00001f00 /* waitcount1 */
+#define PI_W1_SHIFT 8
+#define PI_W2_MASK 0x001f0000 /* waitcount2 */
+#define PI_W2_SHIFT 16
+#define PI_W3_MASK 0x1f000000 /* waitcount3 */
+#define PI_W3_SHIFT 24
+
+/* prog_waitcount */
+#define PW_W0_MASK 0x0000001f /* waitcount0 */
+#define PW_W1_MASK 0x00001f00 /* waitcount1 */
+#define PW_W1_SHIFT 8
+#define PW_W2_MASK 0x001f0000 /* waitcount2 */
+#define PW_W2_SHIFT 16
+#define PW_W3_MASK 0x1f000000 /* waitcount3 */
+#define PW_W3_SHIFT 24
+
+#define PW_W0 0x0000000c
+#define PW_W1 0x00000a00
+#define PW_W2 0x00020000
+#define PW_W3 0x01000000
+
+/* watchdog */
+#define WATCHDOG_CLOCK 48000000 /* Hz */
+
+/* Fields in pmucontrol */
+#define PCTL_ILP_DIV_MASK 0xffff0000
+#define PCTL_ILP_DIV_SHIFT 16
+#define PCTL_NOILP_ON_WAIT 0x00000200
+#define PCTL_HT_REQ_EN 0x00000100
+#define PCTL_ALP_REQ_EN 0x00000080
+#define PCTL_XTALFREQ_MASK 0x0000007c
+#define PCTL_XTALFREQ_SHIFT 2
+#define PCTL_ILP_DIV_EN 0x00000002
+#define PCTL_LPO_SEL 0x00000001
+
/* gpiotimerval */
#define GPIO_ONTIME_SHIFT 16
#define CC_CFG_EM_PCMCIA 0x0004 /* PCMCIA */
#define CC_CFG_EM_IDE 0x0006 /* IDE */
#define CC_CFG_DS 0x0010 /* Data size, 0=8bit, 1=16bit */
-#define CC_CFG_CD_MASK 0x0060 /* Sync: Clock divisor */
-#define CC_CFG_CE 0x0080 /* Sync: Clock enable */
-#define CC_CFG_SB 0x0100 /* Sync: Size/Bytestrobe */
+#define CC_CFG_CD_MASK 0x00e0 /* Sync: Clock divisor, rev >= 20 */
+#define CC_CFG_CE 0x0100 /* Sync: Clock enable, rev >= 20 */
+#define CC_CFG_SB 0x0200 /* Sync: Size/Bytestrobe, rev >= 20 */
+#define CC_CFG_IS 0x0400 /* Extif Sync Clk Select, rev >= 20 */
/* ExtBus address space */
#define CC_EB_BASE 0x1a000000 /* Chipc ExtBus base address */
/* Start/busy bit in flashcontrol */
#define SFLASH_OPCODE 0x000000ff
#define SFLASH_ACTION 0x00000700
+#define SFLASH_CS_ACTIVE 0x00001000 /* Chip Select Active, rev >= 20 */
#define SFLASH_START 0x80000000
#define SFLASH_BUSY SFLASH_START
#define SFLASH_ST_BE 0x00c7 /* Bulk Erase */
#define SFLASH_ST_DP 0x00b9 /* Deep Power-down */
#define SFLASH_ST_RES 0x03ab /* Read Electronic Signature */
+#define SFLASH_ST_CSA 0x1000 /* Keep chip select asserted */
/* Status register bits for ST flashes */
#define SFLASH_ST_WIP 0x01 /* Write In Progress */
#define SFLASH_AT_ID_MASK 0x38
#define SFLASH_AT_ID_SHIFT 3
-/* OTP regions */
-#define OTP_HW_REGION OTPS_HW_PROTECT
-#define OTP_SW_REGION OTPS_SW_PROTECT
-#define OTP_CID_REGION OTPS_CID_PROTECT
-
-/* OTP regions (Byte offsets from otp size) */
-#define OTP_SWLIM_OFF (-8)
-#define OTP_CIDBASE_OFF 0
-#define OTP_CIDLIM_OFF 8
-
-/* Predefined OTP words (Word offset from otp size) */
-#define OTP_BOUNDARY_OFF (-4)
-#define OTP_HWSIGN_OFF (-3)
-#define OTP_SWSIGN_OFF (-2)
-#define OTP_CIDSIGN_OFF (-1)
-
-#define OTP_CID_OFF 0
-#define OTP_PKG_OFF 1
-#define OTP_FID_OFF 2
-#define OTP_RSV_OFF 3
-#define OTP_LIM_OFF 4
-
-#define OTP_SIGNATURE 0x578a
-#define OTP_MAGIC 0x4e56
-
/*
* These are the UART port assignments, expressed as offsets from the base
* register. These assignments should hold for any serial port based on
#define UART_LSR_RXRDY 0x01 /* Receiver ready */
#define UART_FCR_FIFO_ENABLE 1 /* FIFO control register bit controlling FIFO enable/disable */
+/* Interrupt Identity Register (IIR) bits */
+#define UART_IIR_FIFO_MASK 0xc0 /* IIR FIFO disable/enabled mask */
+#define UART_IIR_INT_MASK 0xf /* IIR interrupt ID source */
+#define UART_IIR_MDM_CHG 0x0 /* Modem status changed */
+#define UART_IIR_NOINT 0x1 /* No interrupt pending */
+#define UART_IIR_THRE 0x2 /* THR empty */
+#define UART_IIR_RCVD_DATA 0x4 /* Received data available */
+#define UART_IIR_RCVR_STATUS 0x6 /* Receiver status */
+#define UART_IIR_CHAR_TIME 0xc /* Character time */
+
/* Interrupt Enable Register (IER) bits */
#define UART_IER_EDSSI 8 /* enable modem status interrupt */
#define UART_IER_ELSI 4 /* enable receiver line status interrupt */
#define UART_IER_ETBEI 2 /* enable transmitter holding register empty interrupt */
#define UART_IER_ERBFI 1 /* enable data available interrupt */
+/* pmustatus */
+#define PST_INTPEND 0x0040
+#define PST_SBCLKST 0x0030
+#define PST_ALPAVAIL 0x0008
+#define PST_HTAVAIL 0x0004
+#define PST_RESINIT 0x0003
+
+/* pmucapabilities */
+#define PCAP_REV_MASK 0x000000ff
+
+/* PMU Resource Request Timer registers */
+/* This is based on PmuRev0 */
+#define PRRT_TIME_MASK 0x03ff
+#define PRRT_INTEN 0x0400
+#define PRRT_REQ_ACTIVE 0x0800
+#define PRRT_ALP_REQ 0x1000
+#define PRRT_HT_REQ 0x2000
+
+/* PMU resource bit position */
+#define PMURES_BIT(bit) (1 << (bit))
+
+/* PMU corerev and chip specific PLL controls.
+ * PMU<rev>_PLL<num>_XXXX where <rev> is PMU corerev and <num> is an arbitary number
+ * to differentiate different PLLs controlled by the same PMU rev.
+ */
+/* pllcontrol registers */
+/* PDIV, div_phy, div_arm, div_adc, dith_sel, ioff, kpd_scale, lsb_sel, mash_sel, lf_c & lf_r */
+#define PMU0_PLL0_PLLCTL0 0
+#define PMU0_PLL0_PC0_PDIV_MASK 1
+#define PMU0_PLL0_PC0_PDIV_FREQ 25000
+#define PMU0_PLL0_PC0_DIV_ARM_MASK 0x00000038
+#define PMU0_PLL0_PC0_DIV_ARM_SHIFT 3
+#define PMU0_PLL0_PC0_DIV_ARM_BASE 8
+
+/* PC0_DIV_ARM for PLLOUT_ARM */
+#define PMU0_PLL0_PC0_DIV_ARM_110MHZ 0
+#define PMU0_PLL0_PC0_DIV_ARM_97_7MHZ 1
+#define PMU0_PLL0_PC0_DIV_ARM_88MHZ 2
+#define PMU0_PLL0_PC0_DIV_ARM_80MHZ 3 /* Default */
+#define PMU0_PLL0_PC0_DIV_ARM_73_3MHZ 4
+#define PMU0_PLL0_PC0_DIV_ARM_67_7MHZ 5
+#define PMU0_PLL0_PC0_DIV_ARM_62_9MHZ 6
+#define PMU0_PLL0_PC0_DIV_ARM_58_6MHZ 7
+
+/* Wildcard base, stop_mod, en_lf_tp, en_cal & lf_r2 */
+#define PMU0_PLL0_PLLCTL1 1
+#define PMU0_PLL0_PC1_WILD_INT_MASK 0xf0000000
+#define PMU0_PLL0_PC1_WILD_INT_SHIFT 28
+#define PMU0_PLL0_PC1_WILD_FRAC_MASK 0x0fffff00
+#define PMU0_PLL0_PC1_WILD_FRAC_SHIFT 8
+#define PMU0_PLL0_PC1_STOP_MOD 0x00000040
+
+/* Wildcard base, vco_calvar, vco_swc, vco_var_selref, vso_ical & vco_sel_avdd */
+#define PMU0_PLL0_PLLCTL2 2
+#define PMU0_PLL0_PC2_WILD_INT_MASK 0xf
+#define PMU0_PLL0_PC2_WILD_INT_SHIFT 4
+
+/* Chip specific PMU resources. */
+#define RES4328_EXT_SWITCHER_PWM 0 /* 0x00001 */
+#define RES4328_BB_SWITCHER_PWM 1 /* 0x00002 */
+#define RES4328_BB_SWITCHER_BURST 2 /* 0x00004 */
+#define RES4328_BB_EXT_SWITCHER_BURST 3 /* 0x00008 */
+#define RES4328_ILP_REQUEST 4 /* 0x00010 */
+#define RES4328_RADIO_SWITCHER_PWM 5 /* 0x00020 */
+#define RES4328_RADIO_SWITCHER_BURST 6 /* 0x00040 */
+#define RES4328_ROM_SWITCH 7 /* 0x00080 */
+#define RES4328_PA_REF_LDO 8 /* 0x00100 */
+#define RES4328_RADIO_LDO 9 /* 0x00200 */
+#define RES4328_AFE_LDO 10 /* 0x00400 */
+#define RES4328_PLL_LDO 11 /* 0x00800 */
+#define RES4328_BG_FILTBYP 12 /* 0x01000 */
+#define RES4328_TX_FILTBYP 13 /* 0x02000 */
+#define RES4328_RX_FILTBYP 14 /* 0x04000 */
+#define RES4328_XTAL_PU 15 /* 0x08000 */
+#define RES4328_XTAL_EN 16 /* 0x10000 */
+#define RES4328_BB_PLL_FILTBYP 17 /* 0x20000 */
+#define RES4328_RF_PLL_FILTBYP 18 /* 0x40000 */
+#define RES4328_BB_PLL_PU 19 /* 0x80000 */
+
+#define RES5354_EXT_SWITCHER_PWM 0 /* 0x00001 */
+#define RES5354_BB_SWITCHER_PWM 1 /* 0x00002 */
+#define RES5354_BB_SWITCHER_BURST 2 /* 0x00004 */
+#define RES5354_BB_EXT_SWITCHER_BURST 3 /* 0x00008 */
+#define RES5354_ILP_REQUEST 4 /* 0x00010 */
+#define RES5354_RADIO_SWITCHER_PWM 5 /* 0x00020 */
+#define RES5354_RADIO_SWITCHER_BURST 6 /* 0x00040 */
+#define RES5354_ROM_SWITCH 7 /* 0x00080 */
+#define RES5354_PA_REF_LDO 8 /* 0x00100 */
+#define RES5354_RADIO_LDO 9 /* 0x00200 */
+#define RES5354_AFE_LDO 10 /* 0x00400 */
+#define RES5354_PLL_LDO 11 /* 0x00800 */
+#define RES5354_BG_FILTBYP 12 /* 0x01000 */
+#define RES5354_TX_FILTBYP 13 /* 0x02000 */
+#define RES5354_RX_FILTBYP 14 /* 0x04000 */
+#define RES5354_XTAL_PU 15 /* 0x08000 */
+#define RES5354_XTAL_EN 16 /* 0x10000 */
+#define RES5354_BB_PLL_FILTBYP 17 /* 0x20000 */
+#define RES5354_RF_PLL_FILTBYP 18 /* 0x40000 */
+#define RES5354_BB_PLL_PU 19 /* 0x80000 */
+
+/* pllcontrol registers */
+/* ndiv_pwrdn, pwrdn_ch<x>, refcomp_pwrdn, dly_ch<x>, p1div, p2div, _bypsss_sdmod */
+#define PMU1_PLL0_PLLCTL0 0
+#define PMU1_PLL0_PC0_P1DIV_MASK 0x00f00000
+#define PMU1_PLL0_PC0_P1DIV_SHIFT 20
+#define PMU1_PLL0_PC0_P2DIV_MASK 0x0f000000
+#define PMU1_PLL0_PC0_P2DIV_SHIFT 24
+
+/* m<x>div */
+#define PMU1_PLL0_PLLCTL1 1
+#define PMU1_PLL0_PC1_M1DIV_MASK 0x000000ff
+#define PMU1_PLL0_PC1_M1DIV_SHIFT 0
+#define PMU1_PLL0_PC1_M2DIV_MASK 0x0000ff00
+#define PMU1_PLL0_PC1_M2DIV_SHIFT 8
+#define PMU1_PLL0_PC1_M3DIV_MASK 0x00ff0000
+#define PMU1_PLL0_PC1_M3DIV_SHIFT 16
+#define PMU1_PLL0_PC1_M4DIV_MASK 0xff000000
+#define PMU1_PLL0_PC1_M4DIV_SHIFT 24
+
+/* m<x>div, ndiv_dither_mfb, ndiv_mode, ndiv_int */
+#define PMU1_PLL0_PLLCTL2 2
+#define PMU1_PLL0_PC2_M5DIV_MASK 0x000000ff
+#define PMU1_PLL0_PC2_M5DIV_SHIFT 0
+#define PMU1_PLL0_PC2_M6DIV_MASK 0x0000ff00
+#define PMU1_PLL0_PC2_M6DIV_SHIFT 8
+#define PMU1_PLL0_PC2_NDIV_MODE_MASK 0x000e0000
+#define PMU1_PLL0_PC2_NDIV_MODE_SHIFT 17
+#define PMU1_PLL0_PC2_NDIV_INT_MASK 0x1ff00000
+#define PMU1_PLL0_PC2_NDIV_INT_SHIFT 20
+
+/* ndiv_frac */
+#define PMU1_PLL0_PLLCTL3 3
+#define PMU1_PLL0_PC3_NDIV_FRAC_MASK 0x00ffffff
+#define PMU1_PLL0_PC3_NDIV_FRAC_SHIFT 0
+
+/* pll_ctrl */
+#define PMU1_PLL0_PLLCTL4 4
+
+/* pll_ctrl, vco_rng, clkdrive_ch<x> */
+#define PMU1_PLL0_PLLCTL5 5
+#define PMU1_PLL0_PC5_CLK_DRV_MASK 0xffffff00
+#define PMU1_PLL0_PC5_CLK_DRV_SHIFT 8
+
+#define RES4325_BUCK_BOOST_BURST 0 /* 0x00000001 */
+#define RES4325_CBUCK_BURST 1 /* 0x00000002 */
+#define RES4325_CBUCK_PWM 2 /* 0x00000004 */
+#define RES4325_CLDO_CBUCK_BURST 3 /* 0x00000008 */
+#define RES4325_CLDO_CBUCK_PWM 4 /* 0x00000010 */
+#define RES4325_BUCK_BOOST_PWM 5 /* 0x00000020 */
+#define RES4325_ILP_REQUEST 6 /* 0x00000040 */
+#define RES4325_ABUCK_BURST 7 /* 0x00000080 */
+#define RES4325_ABUCK_PWM 8 /* 0x00000100 */
+#define RES4325_LNLDO1_PU 9 /* 0x00000200 */
+#define RES4325_LNLDO2_PU 10 /* 0x00000400 */
+#define RES4325_LNLDO3_PU 11 /* 0x00000800 */
+#define RES4325_LNLDO4_PU 12 /* 0x00001000 */
+#define RES4325_XTAL_PU 13 /* 0x00002000 */
+#define RES4325_ALP_AVAIL 14 /* 0x00004000 */
+#define RES4325_RX_PWRSW_PU 15 /* 0x00008000 */
+#define RES4325_TX_PWRSW_PU 16 /* 0x00010000 */
+#define RES4325_RFPLL_PWRSW_PU 17 /* 0x00020000 */
+#define RES4325_LOGEN_PWRSW_PU 18 /* 0x00040000 */
+#define RES4325_AFE_PWRSW_PU 19 /* 0x00080000 */
+#define RES4325_BBPLL_PWRSW_PU 20 /* 0x00100000 */
+#define RES4325_HT_AVAIL 21 /* 0x00200000 */
+
+/* Chip specific ChipStatus register bits */
+#define CST4325_SPROM_OTP_SEL_MASK 0x00000003
+#define CST4325_DEFCIS_SEL 0 /* OTP is powered up, use def. CIS, no SPROM */
+#define CST4325_SPROM_SEL 1 /* OTP is powered up, SPROM is present */
+#define CST4325_OTP_SEL 2 /* OTP is powered up, no SPROM */
+#define CST4325_OTP_PWRDN 3 /* OTP is powered down, SPROM is present */
+#define CST4325_SDIO_USB_MODE_MASK 0x00000004
+#define CST4325_SDIO_USB_MODE_SHIFT 2
+#define CST4325_RCAL_VALID_MASK 0x00000008
+#define CST4325_RCAL_VALID_SHIFT 3
+#define CST4325_RCAL_VALUE_MASK 0x000001f0
+#define CST4325_RCAL_VALUE_SHIFT 4
+#define CST4325_PMUTOP_2B_MASK 0x00000200 /* 1 for 2b, 0 for to 2a */
+#define CST4325_PMUTOP_2B_SHIFT 9
+
+#define RES4312_SWITCHER_BURST 0 /* 0x00000001 */
+#define RES4312_SWITCHER_PWM 1 /* 0x00000002 */
+#define RES4312_PA_REF_LDO 2 /* 0x00000004 */
+#define RES4312_CORE_LDO_BURST 3 /* 0x00000008 */
+#define RES4312_CORE_LDO_PWM 4 /* 0x00000010 */
+#define RES4312_RADIO_LDO 5 /* 0x00000020 */
+#define RES4312_ILP_REQUEST 6 /* 0x00000040 */
+#define RES4312_BG_FILTBYP 7 /* 0x00000080 */
+#define RES4312_TX_FILTBYP 8 /* 0x00000100 */
+#define RES4312_RX_FILTBYP 9 /* 0x00000200 */
+#define RES4312_XTAL_PU 10 /* 0x00000400 */
+#define RES4312_ALP_AVAIL 11 /* 0x00000800 */
+#define RES4312_BB_PLL_FILTBYP 12 /* 0x00001000 */
+#define RES4312_RF_PLL_FILTBYP 13 /* 0x00002000 */
+#define RES4312_HT_AVAIL 14 /* 0x00004000 */
+
+/*
+* Maximum delay for the PMU state transition.
+* This is an upper bound intended for spinwaits etc.
+*/
+#define PMU_MAX_TRANSITION_DLY 15000
+
#endif /* _SBCHIPC_H */
projects / openwrt.git / blobdiff