ath9k: fix queue pending frame counter tracking by cleaning up tx queue selection

[openwrt.git] / target / linux / at91 / config-default

diff --git a/target/linux/at91/config-default b/target/linux/at91/config-default
index 5d30585..9da6aac 100644 (file)
--- a/target/linux/at91/config-default
+++ b/target/linux/at91/config-default
@@ -12,16 +12,19 @@ CONFIG_ARCH_AT91SAM9G20=y
 # CONFIG_ARCH_AT91SAM9G45 is not set
 # CONFIG_ARCH_AT91SAM9RL is not set
 # CONFIG_ARCH_AT91X40 is not set
+# CONFIG_ARCH_CNS3XXX is not set
 # CONFIG_ARCH_NUC93X is not set
 CONFIG_ARCH_REQUIRE_GPIOLIB=y
 # CONFIG_ARCH_S5P6440 is not set
 # CONFIG_ARCH_S5P6442 is not set
+# CONFIG_ARCH_S5PC100 is not set
 # CONFIG_ARCH_S5PV210 is not set
 # CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
 # CONFIG_ARCH_SHMOBILE is not set
 # CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
 # CONFIG_ARCH_SUPPORTS_MSI is not set
 CONFIG_ARCH_SUSPEND_POSSIBLE=y
+# CONFIG_ARCH_VEXPRESS is not set
 CONFIG_ARM=y
 CONFIG_ARM_L1_CACHE_SHIFT=5
 CONFIG_ARM_THUMB=y
@@ -72,10 +75,8 @@ CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
 CONFIG_GENERIC_FIND_LAST_BIT=y
 CONFIG_GENERIC_GPIO=y
 CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
-CONFIG_GENERIC_PWM=y
 CONFIG_GPIOLIB=y
 CONFIG_GPIO_DEVICE=y
-# CONFIG_GPIO_PWM is not set
 CONFIG_GPIO_SYSFS=y
 # CONFIG_HAMRADIO is not set
 CONFIG_HARDIRQS_SW_RESEND=y
@@ -110,6 +111,8 @@ CONFIG_MACB=y
 # CONFIG_MACH_AT91SAM9G20EK_2MMC is not set
 # CONFIG_MACH_CPU9G20 is not set
 CONFIG_MACH_NETUS_FOXBOARD=y
+# CONFIG_MACH_PORTUXG20 is not set
+# CONFIG_MACH_STAMP9G20 is not set
 # CONFIG_MFD_T7L66XB is not set
 # CONFIG_MII is not set
 CONFIG_MMC=y
@@ -121,6 +124,7 @@ CONFIG_MTD_DATAFLASH=y
 # CONFIG_MTD_DATAFLASH_WRITE_VERIFY is not set
 CONFIG_NEED_DMA_MAP_STATE=y
 # CONFIG_NETDEV_1000 is not set
+# CONFIG_NETUS_FOXGM is not set
 CONFIG_NETUS_HEARTBEAT_LED=y
 CONFIG_NETUS_SERIALS=y
 # CONFIG_NETUS_USE_DATAFLASH is not set
@@ -131,10 +135,12 @@ CONFIG_PAGE_OFFSET=0xC0000000
 # CONFIG_PCI_SYSCALL is not set
 CONFIG_PERF_USE_VMALLOC=y
 CONFIG_PHYLIB=y
+# CONFIG_PLAT_SPEAR is not set
 CONFIG_RTC_CLASS=y
 CONFIG_RTC_DRV_AT91SAM9=y
 CONFIG_RTC_DRV_AT91SAM9_GPBR=0
 CONFIG_RTC_DRV_AT91SAM9_RTT=0
+# CONFIG_RTC_DRV_CMOS is not set
 # CONFIG_SCSI_DMA is not set
 CONFIG_SCSI_MOD=y
 # CONFIG_SDIO_UART is not set