generic: ar8216: use ar8216_read_port_link to get the CPU port link parameters

[openwrt.git] / target / linux / brcm63xx / patches-3.0 / 452-board_V2500V.patch

diff --git a/target/linux/brcm63xx/patches-3.0/452-board_V2500V.patch b/target/linux/brcm63xx/patches-3.0/452-board_V2500V.patch
index 12d03f3..a7ab289 100644 (file)
--- a/target/linux/brcm63xx/patches-3.0/452-board_V2500V.patch
+++ b/target/linux/brcm63xx/patches-3.0/452-board_V2500V.patch
@@ -1,6 +1,6 @@
 --- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
 +++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -858,6 +858,63 @@ static struct board_info __initdata boar
+@@ -853,6 +853,63 @@ static struct board_info __initdata boar
        },
  };
  
@@ -64,7 +64,7 @@
  #endif
  
  /*
-@@ -1911,6 +1968,7 @@ static const struct board_info __initdat
+@@ -1906,6 +1963,7 @@ static const struct board_info __initdat
        &board_96348_D4PW,
        &board_spw500v,
        &board_96348sv,
@@ -72,9 +72,9 @@
  #endif
  
  #ifdef CONFIG_BCM63XX_CPU_6358
-@@ -2070,6 +2128,22 @@ void __init board_prom_init(void)
-               val &= MPI_CSBASE_BASE_MASK;
-       }
+@@ -2059,6 +2117,22 @@ void __init board_prom_init(void)
+       val = bcm_mpi_readl(MPI_CSBASE_REG(0));
+       val &= MPI_CSBASE_BASE_MASK;
        boot_addr = (u8 *)KSEG1ADDR(val);
 +      printk(KERN_INFO PFX "Boot address 0x%08x\n",(unsigned int)boot_addr);
 +
@@ -95,17 +95,16 @@
  
        /* dump cfe version */
        cfe = boot_addr + BCM963XX_CFE_VERSION_OFFSET;
-@@ -2274,6 +2348,14 @@ int __init board_register_devices(void)
-               val = bcm_mpi_readl(MPI_CSBASE_REG(0));
-               val &= MPI_CSBASE_BASE_MASK;
-       }
-+
+@@ -2260,6 +2334,13 @@ int __init board_register_devices(void)
+       val = bcm_mpi_readl(MPI_CSBASE_REG(0));
+       val &= MPI_CSBASE_BASE_MASK;
+ 
 +      /* BT Voyager 2500V has 8 Meg flash in two 4 Meg banks */
 +      /* Loading from CFE always uses Bank 0 */
 +      if (!strcmp(board.name, "V2500V_BB")) {
 +              printk(KERN_INFO PFX "V2500V: Start in Bank 0\n");
 +              val = val + 0x400000; // Select Bank 0 start address
-+              }
++      }
 +
        mtd_resources[0].start = val;
        mtd_resources[0].end = 0x1FFFFFFF;