-The network configuration in Kamikaze is stored in \texttt{/etc/config/network}
+The network configuration is stored in \texttt{/etc/config/network}
and is divided into interface configurations.
Each interface configuration either refers directly to an ethernet/wifi
interface (\texttt{eth0}, \texttt{wl0}, ..) or to a bridge containing multiple interfaces.
\end{Verbatim}
It is possible to use VLAN tagging on an interface simply by adding the VLAN IDs
-to it, e.g. \texttt{eth0.1}. These can be nested as well.
+to it, e.g. \texttt{eth0.1}. These can be nested as well. See the switch section for
+this.
+
+\begin{Verbatim}
+config inter
+\end{Verbatim}
This sets up a simple static configuration for \texttt{eth0}. \texttt{proto} specifies the
protocol used for the interface. The default image usually provides \texttt{'none'}
When using the \texttt{'static'} method like in the example, the options \texttt{ipaddr} and
\texttt{netmask} are mandatory, while \texttt{gateway} and \texttt{dns} are optional.
-You can specify more than one DNS server, separated with spaces.
+You can specify more than one DNS server, separated with spaces:
+
+\begin{Verbatim}
+config interface "lan"
+ option ifname "eth0"
+ option proto "static"
+ ...
+ option dns "192.168.1.254 192.168.1.253" (optional)
+\end{Verbatim}
DHCP currently only accepts \texttt{ipaddr} (IP address to request from the server)
and \texttt{hostname} (client hostname identify as) - both are optional.
+\begin{Verbatim}
+config interface "lan"
+ option ifname "eth0"
+ option proto "dhcp"
+ option ipaddr "192.168.1.1" (optional)
+ option hostname "openwrt" (optional)
+\end{Verbatim}
+
PPP based protocols (\texttt{pppoe}, \texttt{pptp}, ...) accept these options:
\begin{itemize}
\item{username} \\
\end{itemize}
For all protocol types, you can also specify the MTU by using the \texttt{mtu} option.
+A sample PPPoE config would look like this:
+
+\begin{Verbatim}
+config interface "lan"
+ option ifname "eth0"
+ option proto "pppoe"
+ option username "username"
+ option password "openwrt"
+ option mtu 1492 (optional)
+\end{Verbatim}
\subsubsection{Setting up static routes}
option vlan2 "4 5"
\end{Verbatim}
+Three interfaces will be automatically created using this switch layout :
+\texttt{eth0.0} (vlan0), \texttt{eth0.1} (vlan1) and \texttt{eth0.2} (vlan2).
+You can then assign those interfaces to a custom network configuration name
+like \texttt{lan}, \texttt{wan} or \texttt{dmz} for instance.
+
\subsubsection{Setting up IPv6 connectivity}
OpenWrt supports IPv6 connectivity using PPP, Tunnel brokers or static
If you use PPP, IPv6 will be setup using IP6CP and there is nothing to
configure.
-To setup an IPv6 tunnel to a tunnel broker, you have to edit the
-\texttt{/etc/config/6tunnel} file and change the settings accordingly :
+To setup an IPv6 tunnel to a tunnel broker, you can install the
+\texttt{6scripts} package and edit the \texttt{/etc/config/6tunnel}
+file and change the settings accordingly :
\begin{Verbatim}
config 6tunnel
option remoteip4 '1.0.0.1'
option localip4 '1.0.0.2'
option localip6 '2001::DEAD::BEEF::1'
- option prefix '/64'
\end{Verbatim}
\begin{itemize}
\item{\texttt{'localip6'}:}
IPv6 address to setup on your tunnel side
This address is given by the tunnel broker
- \item{\texttt{'prefix'}:}
- IPv6 prefix to setup on the LAN.
\end{itemize}
+Using the same package you can also setup an IPv6 bridged connection :
+
+\begin{Verbatim}
+config 6bridge
+ option bridge 'br6'
+\end{Verbatim}
+
+By default the script bridges the WAN interface with the LAN interface
+and uses ebtables to filter anything that is not IPv6 on the bridge.
+This configuration is particularly useful if your router is not
+IPv6 ND proxy capable (see: http://www.rfc-archive.org/getrfc.php?rfc=4389).
+
+
IPv6 static addressing is also supported using a similar setup as
IPv4 but with the \texttt{ip6} prefixing (when applicable).
projects / openwrt.git / blobdiff