lantiq: add runtime generation of /etc/config/network

[openwrt.git] / target / linux / lantiq / base-files / etc / uci-defaults / network

diff --git a/target/linux/lantiq/base-files/etc/uci-defaults/network b/target/linux/lantiq/base-files/etc/uci-defaults/network
new file mode 100755 (executable)
index 0000000..f9a7237
--- /dev/null
+++ b/target/linux/lantiq/base-files/etc/uci-defaults/network
@@ -0,0 +1,126 @@
+#!/bin/sh
+#
+# Copyright (C) 2011 OpenWrt.org
+#
+
+set_interface_loopback() {
+       uci batch <<EOF
+set network.loopback='interface'
+set network.loopback.ifname='lo'
+set network.loopback.proto='static'
+set network.loopback.ipaddr='127.0.0.1'
+set network.loopback.netmask='255.0.0.0'
+EOF
+}
+
+set_interface_raw() {
+       local cfg=$1
+       local ifname=$2
+
+       uci batch <<EOF
+set network.$cfg='interface'
+set network.$cfg.ifname='$ifname'
+set network.$cfg.proto='none'
+EOF
+}
+
+set_interface_lan() {
+       local ifname=$1
+
+       uci batch <<EOF
+set network.lan='interface'
+set network.lan.ifname='$ifname'
+set network.lan.type='bridge'
+set network.lan.proto='static'
+set network.lan.ipaddr='192.168.1.1'
+set network.lan.netmask='255.255.255.0'
+EOF
+}
+
+set_interface_wan() {
+       local ifname=$1
+
+       uci batch <<EOF
+set network.wan='interface'
+set network.wan.ifname='$ifname'
+set network.wan.proto='dhcp'
+EOF
+}
+
+set_atm_wan() {
+       local vpi=$1
+       local vci=$2
+       local encaps=$3
+       local payload=$4
+
+       uci batch <<EOF
+set network.atm='atm-bridge'
+set network.atm.unit='0'
+set network.atm.vpi='$vpi'
+set network.atm.vci='$vci'
+set network.atm.encaps='$encaps'
+set network.atm.payload='$payload'
+set network.wan='interface'
+set network.wan.ifname='nas0'
+set network.wan.proto='pppoe'
+set network.wan.username='foo'
+set network.wan.password='bar'
+EOF
+}
+
+set_interfaces_lan_wan() {
+       local lan_ifname=$1
+       local wan_ifname=$2
+
+       set_interface_lan "$lan_ifname"
+       set_interface_wan "$wan_ifname"
+}
+
+add_switch() {
+       local name=$1
+       local reset=$2
+       local enable=$3
+       uci batch <<EOF
+add network switch
+set network.@switch[-1].name='$name'
+set network.@switch[-1].reset='$reset'
+set network.@switch[-1].enable_vlan='$enable'
+EOF
+}
+
+add_switch_vlan() {
+       local device=$1
+       local vlan=$2
+       local ports=$3
+       uci batch <<EOF
+add network switch_vlan
+set network.@switch_vlan[-1].device='$device'
+set network.@switch_vlan[-1].vlan='$vlan'
+set network.@switch_vlan[-1].ports='$ports'
+EOF
+}
+
+[ -e /etc/config/network ] && exit 0
+
+. /lib/lantiq.sh
+
+touch /etc/config/network
+
+set_interface_loopback
+set_interface_lan 'eth0'
+
+dsl=$(lantiq_soc_has_adsl)
+[ -z "$dsl" ] || set_atm_wan '1' '32' 'llc' 'bridged'
+
+board=$(lantiq_board_name)
+
+case "$board" in
+*)
+       # custom foo goes here
+       true
+       ;;
+esac
+
+uci commit network
+
+exit 0