brcm63xx cleanups; add a watchdog driver, indent serial console driver, add support...

[openwrt.git] / scripts / flash.sh

diff --git a/scripts/flash.sh b/scripts/flash.sh
old mode 100644 (file)
new mode 100755 (executable)
index e711086..8841c35
--- a/scripts/flash.sh
+++ b/scripts/flash.sh
@@ -1,9 +1,9 @@
 #!/bin/bash
 #!/bin/bash

-
-# flash script for linksys and asus routers 
+#
+# tftp flash script for wireless routers 

 #
 # Copyright (C) 2004 by Oleg I. Vdovikin <oleg@cs.msu.su>
 #
 # Copyright (C) 2004 by Oleg I. Vdovikin <oleg@cs.msu.su>

-# Copyright (C) 2005 by Waldemar Brodkorb <wbx@dass-it.de>
+# Copyright (C) 2005 by Waldemar Brodkorb <wbx@openwrt.org>

 #
 # This program is free software; you can redistribute it and/or modify
 # it under the terms of the GNU General Public License as published by
 #
 # This program is free software; you can redistribute it and/or modify
 # it under the terms of the GNU General Public License as published by


@@ -24,11 +24,11 @@ if [ -z "$1" ] || [ ! -f $1 ] || [ -z $2 ]; then
     echo Usage: $0 firmware vendor
 cat << EOF
 IMPORTANT:
     echo Usage: $0 firmware vendor
 cat << EOF
 IMPORTANT:

-Notes for Linksys router: 
+Notes for Linksys / Asus WL500gx router: 

    be sure you have set boot_wait to yes. Power on your router
    after executing this script.
  
    be sure you have set boot_wait to yes. Power on your router
    after executing this script.
  

-Notes for Asus router:
+Notes for Asus WL500g router:

    be sure POWER led is flashing (If this is not the case
    poweroff the device, push the reset button & power on
    it again, then release button)
    be sure POWER led is flashing (If this is not the case
    poweroff the device, push the reset button & power on
    it again, then release button)


@@ -36,6 +36,16 @@ Notes for Asus router:
 1) connect your pc to the LAN port
 2) be sure your link is up and has an address in the
    192.168.1.0/24 address range (and not the 192.168.1.1)
 1) connect your pc to the LAN port
 2) be sure your link is up and has an address in the
    192.168.1.0/24 address range (and not the 192.168.1.1)

+
+Notes for Toshiba router:
+   boot_wait is enabled by default on these units.
+
+1) connect your pc to any of the four LAN ports
+2) be sure your link is up and has an address in the
+   192.168.10.1/24 address range (and not the 192.168.10.1)
+3) run this script (unit will only accept .trx images)
+4) Turn unit power on.
+

 EOF
     exit 0
 fi
 EOF
     exit 0
 fi


@@ -49,4 +59,8 @@ elif [ "$2" == "linksys" ]; then
 echo Flashing 192.168.1.1 using $1...
 echo -en "rexmt 1\ntrace\nbinary\nput $1\nquit\n" | tftp 192.168.1.1
 echo Please wait until power led stops flashing. Do not poweroff! Then you can login via telnet 192.168.1.1.
 echo Flashing 192.168.1.1 using $1...
 echo -en "rexmt 1\ntrace\nbinary\nput $1\nquit\n" | tftp 192.168.1.1
 echo Please wait until power led stops flashing. Do not poweroff! Then you can login via telnet 192.168.1.1.

+elif [ "$2" == "toshiba" ]; then
+echo Flashing 192.168.10.1 using $1...
+echo -en "rexmt 1\ntrace\nbinary\nput $1\nquit\n" | tftp 192.168.10.1
+echo Unit will automatically reboot within 5 minutes.  Do not power off.  Then you can login via telnet 192.168.10.1.

 fi
 fi