struct pmu0_plltab_entry {
u16 freq; /* Crystal frequency in kHz.*/
u8 xf; /* Crystal frequency value for PMU control */
-@@ -506,3 +521,82 @@ void ssb_pmu_init(struct ssb_chipcommon
+@@ -317,6 +332,12 @@ static void ssb_pmu_pll_init(struct ssb_
+ case 0x5354:
+ ssb_pmu0_pllinit_r0(cc, crystalfreq);
+ break;
++ case 0x4322:
++ if (cc->pmu.rev == 2) {
++ chipco_write32(cc, SSB_CHIPCO_PLLCTL_ADDR, 0x0000000A);
++ chipco_write32(cc, SSB_CHIPCO_PLLCTL_DATA, 0x380005C0);
++ }
++ break;
+ default:
+ ssb_printk(KERN_ERR PFX
+ "ERROR: PLL init unknown for device %04X\n",
+@@ -402,6 +423,7 @@ static void ssb_pmu_resources_init(struc
+
+ switch (bus->chip_id) {
+ case 0x4312:
++ case 0x4322:
+ /* We keep the default settings:
+ * min_msk = 0xCBB
+ * max_msk = 0x7FFFF
+@@ -506,3 +528,82 @@ void ssb_pmu_init(struct ssb_chipcommon
ssb_pmu_pll_init(cc);
ssb_pmu_resources_init(cc);
}
/* ssb must be initialized after PCI but before the ssb drivers.
--- a/drivers/ssb/pci.c
+++ b/drivers/ssb/pci.c
-@@ -169,8 +169,14 @@ err_pci:
+@@ -167,10 +167,16 @@ err_pci:
+ }
+
/* Get the word-offset for a SSB_SPROM_XXX define. */
- #define SPOFF(offset) (((offset) - SSB_SPROM_BASE) / sizeof(u16))
+-#define SPOFF(offset) (((offset) - SSB_SPROM_BASE) / sizeof(u16))
++#define SPOFF(offset) ((offset) / sizeof(u16))
/* Helper to extract some _offset, which is one of the SSB_SPROM_XXX defines. */
-#define SPEX(_outvar, _offset, _mask, _shift) \
+#define SPEX16(_outvar, _offset, _mask, _shift) \
static inline u8 ssb_crc8(u8 crc, u8 data)
{
+@@ -247,7 +253,7 @@ static int sprom_do_read(struct ssb_bus
+ int i;
+
+ for (i = 0; i < bus->sprom_size; i++)
+- sprom[i] = ioread16(bus->mmio + SSB_SPROM_BASE + (i * 2));
++ sprom[i] = ioread16(bus->mmio + bus->sprom_offset + (i * 2));
+
+ return 0;
+ }
+@@ -278,7 +284,7 @@ static int sprom_do_write(struct ssb_bus
+ ssb_printk("75%%");
+ else if (i % 2)
+ ssb_printk(".");
+- writew(sprom[i], bus->mmio + SSB_SPROM_BASE + (i * 2));
++ writew(sprom[i], bus->mmio + bus->sprom_offset + (i * 2));
+ mmiowb();
+ msleep(20);
+ }
@@ -474,12 +480,14 @@ static void sprom_extract_r8(struct ssb_
/* extract the MAC address */
sprom_extract_r123(out, in);
}
}
+@@ -568,6 +620,14 @@ static int ssb_pci_sprom_get(struct ssb_
+ int err = -ENOMEM;
+ u16 *buf;
+
++ if (!ssb_is_sprom_available(bus)) {
++ ssb_printk(KERN_ERR PFX "No SPROM available!\n");
++ return -ENODEV;
++ }
++
++ bus->sprom_offset = (bus->chipco.dev->id.revision < 31) ?
++ SSB_SPROM_BASE1 : SSB_SPROM_BASE31;
++
+ buf = kcalloc(SSB_SPROMSIZE_WORDS_R123, sizeof(u16), GFP_KERNEL);
+ if (!buf)
+ goto out;
--- a/drivers/ssb/pcmcia.c
+++ b/drivers/ssb/pcmcia.c
@@ -583,7 +583,7 @@ static int ssb_pcmcia_sprom_write_all(st
"Could not disable SPROM write access.\n");
failed = 1;
}
-@@ -678,7 +678,8 @@ int ssb_pcmcia_get_invariants(struct ssb
- sprom->board_rev = tuple.TupleData[1];
- break;
- case SSB_PCMCIA_CIS_PA:
+@@ -617,134 +617,140 @@ static int ssb_pcmcia_sprom_check_crc(co
+ } \
+ } while (0)
+
+-int ssb_pcmcia_get_invariants(struct ssb_bus *bus,
+- struct ssb_init_invariants *iv)
++static int ssb_pcmcia_get_mac(struct pcmcia_device *p_dev,
++ tuple_t *tuple,
++ void *priv)
+ {
+- tuple_t tuple;
+- int res;
+- unsigned char buf[32];
++ struct ssb_sprom *sprom = priv;
++
++ if (tuple->TupleData[0] != CISTPL_FUNCE_LAN_NODE_ID)
++ return -EINVAL;
++ if (tuple->TupleDataLen != ETH_ALEN + 2)
++ return -EINVAL;
++ if (tuple->TupleData[1] != ETH_ALEN)
++ return -EINVAL;
++ memcpy(sprom->il0mac, &tuple->TupleData[2], ETH_ALEN);
++ return 0;
++};
++
++static int ssb_pcmcia_do_get_invariants(struct pcmcia_device *p_dev,
++ tuple_t *tuple,
++ void *priv)
++{
++ struct ssb_init_invariants *iv = priv;
+ struct ssb_sprom *sprom = &iv->sprom;
+ struct ssb_boardinfo *bi = &iv->boardinfo;
+ const char *error_description;
+
++ GOTO_ERROR_ON(tuple->TupleDataLen < 1, "VEN tpl < 1");
++ switch (tuple->TupleData[0]) {
++ case SSB_PCMCIA_CIS_ID:
++ GOTO_ERROR_ON((tuple->TupleDataLen != 5) &&
++ (tuple->TupleDataLen != 7),
++ "id tpl size");
++ bi->vendor = tuple->TupleData[1] |
++ ((u16)tuple->TupleData[2] << 8);
++ break;
++ case SSB_PCMCIA_CIS_BOARDREV:
++ GOTO_ERROR_ON(tuple->TupleDataLen != 2,
++ "boardrev tpl size");
++ sprom->board_rev = tuple->TupleData[1];
++ break;
++ case SSB_PCMCIA_CIS_PA:
++ GOTO_ERROR_ON((tuple->TupleDataLen != 9) &&
++ (tuple->TupleDataLen != 10),
++ "pa tpl size");
++ sprom->pa0b0 = tuple->TupleData[1] |
++ ((u16)tuple->TupleData[2] << 8);
++ sprom->pa0b1 = tuple->TupleData[3] |
++ ((u16)tuple->TupleData[4] << 8);
++ sprom->pa0b2 = tuple->TupleData[5] |
++ ((u16)tuple->TupleData[6] << 8);
++ sprom->itssi_a = tuple->TupleData[7];
++ sprom->itssi_bg = tuple->TupleData[7];
++ sprom->maxpwr_a = tuple->TupleData[8];
++ sprom->maxpwr_bg = tuple->TupleData[8];
++ break;
++ case SSB_PCMCIA_CIS_OEMNAME:
++ /* We ignore this. */
++ break;
++ case SSB_PCMCIA_CIS_CCODE:
++ GOTO_ERROR_ON(tuple->TupleDataLen != 2,
++ "ccode tpl size");
++ sprom->country_code = tuple->TupleData[1];
++ break;
++ case SSB_PCMCIA_CIS_ANTENNA:
++ GOTO_ERROR_ON(tuple->TupleDataLen != 2,
++ "ant tpl size");
++ sprom->ant_available_a = tuple->TupleData[1];
++ sprom->ant_available_bg = tuple->TupleData[1];
++ break;
++ case SSB_PCMCIA_CIS_ANTGAIN:
++ GOTO_ERROR_ON(tuple->TupleDataLen != 2,
++ "antg tpl size");
++ sprom->antenna_gain.ghz24.a0 = tuple->TupleData[1];
++ sprom->antenna_gain.ghz24.a1 = tuple->TupleData[1];
++ sprom->antenna_gain.ghz24.a2 = tuple->TupleData[1];
++ sprom->antenna_gain.ghz24.a3 = tuple->TupleData[1];
++ sprom->antenna_gain.ghz5.a0 = tuple->TupleData[1];
++ sprom->antenna_gain.ghz5.a1 = tuple->TupleData[1];
++ sprom->antenna_gain.ghz5.a2 = tuple->TupleData[1];
++ sprom->antenna_gain.ghz5.a3 = tuple->TupleData[1];
++ break;
++ case SSB_PCMCIA_CIS_BFLAGS:
++ GOTO_ERROR_ON((tuple->TupleDataLen != 3) &&
++ (tuple->TupleDataLen != 5),
++ "bfl tpl size");
++ sprom->boardflags_lo = tuple->TupleData[1] |
++ ((u16)tuple->TupleData[2] << 8);
++ break;
++ case SSB_PCMCIA_CIS_LEDS:
++ GOTO_ERROR_ON(tuple->TupleDataLen != 5,
++ "leds tpl size");
++ sprom->gpio0 = tuple->TupleData[1];
++ sprom->gpio1 = tuple->TupleData[2];
++ sprom->gpio2 = tuple->TupleData[3];
++ sprom->gpio3 = tuple->TupleData[4];
++ break;
++ }
++ return -ENOSPC; /* continue with next entry */
++
++error:
++ ssb_printk(KERN_ERR PFX
++ "PCMCIA: Failed to fetch device invariants: %s\n",
++ error_description);
++ return -ENODEV;
++}
++
++
++int ssb_pcmcia_get_invariants(struct ssb_bus *bus,
++ struct ssb_init_invariants *iv)
++{
++ struct ssb_sprom *sprom = &iv->sprom;
++ int res;
++
+ memset(sprom, 0xFF, sizeof(*sprom));
+ sprom->revision = 1;
+ sprom->boardflags_lo = 0;
+ sprom->boardflags_hi = 0;
+
+ /* First fetch the MAC address. */
+- memset(&tuple, 0, sizeof(tuple));
+- tuple.DesiredTuple = CISTPL_FUNCE;
+- tuple.TupleData = buf;
+- tuple.TupleDataMax = sizeof(buf);
+- res = pcmcia_get_first_tuple(bus->host_pcmcia, &tuple);
+- GOTO_ERROR_ON(res != 0, "MAC first tpl");
+- res = pcmcia_get_tuple_data(bus->host_pcmcia, &tuple);
+- GOTO_ERROR_ON(res != 0, "MAC first tpl data");
+- while (1) {
+- GOTO_ERROR_ON(tuple.TupleDataLen < 1, "MAC tpl < 1");
+- if (tuple.TupleData[0] == CISTPL_FUNCE_LAN_NODE_ID)
+- break;
+- res = pcmcia_get_next_tuple(bus->host_pcmcia, &tuple);
+- GOTO_ERROR_ON(res != 0, "MAC next tpl");
+- res = pcmcia_get_tuple_data(bus->host_pcmcia, &tuple);
+- GOTO_ERROR_ON(res != 0, "MAC next tpl data");
++ res = pcmcia_loop_tuple(bus->host_pcmcia, CISTPL_FUNCE,
++ ssb_pcmcia_get_mac, sprom);
++ if (res != 0) {
++ ssb_printk(KERN_ERR PFX
++ "PCMCIA: Failed to fetch MAC address\n");
++ return -ENODEV;
+ }
+- GOTO_ERROR_ON(tuple.TupleDataLen != ETH_ALEN + 2, "MAC tpl size");
+- memcpy(sprom->il0mac, &tuple.TupleData[2], ETH_ALEN);
+
+ /* Fetch the vendor specific tuples. */
+- memset(&tuple, 0, sizeof(tuple));
+- tuple.DesiredTuple = SSB_PCMCIA_CIS;
+- tuple.TupleData = buf;
+- tuple.TupleDataMax = sizeof(buf);
+- res = pcmcia_get_first_tuple(bus->host_pcmcia, &tuple);
+- GOTO_ERROR_ON(res != 0, "VEN first tpl");
+- res = pcmcia_get_tuple_data(bus->host_pcmcia, &tuple);
+- GOTO_ERROR_ON(res != 0, "VEN first tpl data");
+- while (1) {
+- GOTO_ERROR_ON(tuple.TupleDataLen < 1, "VEN tpl < 1");
+- switch (tuple.TupleData[0]) {
+- case SSB_PCMCIA_CIS_ID:
+- GOTO_ERROR_ON((tuple.TupleDataLen != 5) &&
+- (tuple.TupleDataLen != 7),
+- "id tpl size");
+- bi->vendor = tuple.TupleData[1] |
+- ((u16)tuple.TupleData[2] << 8);
+- break;
+- case SSB_PCMCIA_CIS_BOARDREV:
+- GOTO_ERROR_ON(tuple.TupleDataLen != 2,
+- "boardrev tpl size");
+- sprom->board_rev = tuple.TupleData[1];
+- break;
+- case SSB_PCMCIA_CIS_PA:
- GOTO_ERROR_ON(tuple.TupleDataLen != 9,
-+ GOTO_ERROR_ON((tuple.TupleDataLen != 9) &&
-+ (tuple.TupleDataLen != 10),
- "pa tpl size");
- sprom->pa0b0 = tuple.TupleData[1] |
- ((u16)tuple.TupleData[2] << 8);
-@@ -718,7 +719,8 @@ int ssb_pcmcia_get_invariants(struct ssb
- sprom->antenna_gain.ghz5.a3 = tuple.TupleData[1];
- break;
- case SSB_PCMCIA_CIS_BFLAGS:
+- "pa tpl size");
+- sprom->pa0b0 = tuple.TupleData[1] |
+- ((u16)tuple.TupleData[2] << 8);
+- sprom->pa0b1 = tuple.TupleData[3] |
+- ((u16)tuple.TupleData[4] << 8);
+- sprom->pa0b2 = tuple.TupleData[5] |
+- ((u16)tuple.TupleData[6] << 8);
+- sprom->itssi_a = tuple.TupleData[7];
+- sprom->itssi_bg = tuple.TupleData[7];
+- sprom->maxpwr_a = tuple.TupleData[8];
+- sprom->maxpwr_bg = tuple.TupleData[8];
+- break;
+- case SSB_PCMCIA_CIS_OEMNAME:
+- /* We ignore this. */
+- break;
+- case SSB_PCMCIA_CIS_CCODE:
+- GOTO_ERROR_ON(tuple.TupleDataLen != 2,
+- "ccode tpl size");
+- sprom->country_code = tuple.TupleData[1];
+- break;
+- case SSB_PCMCIA_CIS_ANTENNA:
+- GOTO_ERROR_ON(tuple.TupleDataLen != 2,
+- "ant tpl size");
+- sprom->ant_available_a = tuple.TupleData[1];
+- sprom->ant_available_bg = tuple.TupleData[1];
+- break;
+- case SSB_PCMCIA_CIS_ANTGAIN:
+- GOTO_ERROR_ON(tuple.TupleDataLen != 2,
+- "antg tpl size");
+- sprom->antenna_gain.ghz24.a0 = tuple.TupleData[1];
+- sprom->antenna_gain.ghz24.a1 = tuple.TupleData[1];
+- sprom->antenna_gain.ghz24.a2 = tuple.TupleData[1];
+- sprom->antenna_gain.ghz24.a3 = tuple.TupleData[1];
+- sprom->antenna_gain.ghz5.a0 = tuple.TupleData[1];
+- sprom->antenna_gain.ghz5.a1 = tuple.TupleData[1];
+- sprom->antenna_gain.ghz5.a2 = tuple.TupleData[1];
+- sprom->antenna_gain.ghz5.a3 = tuple.TupleData[1];
+- break;
+- case SSB_PCMCIA_CIS_BFLAGS:
- GOTO_ERROR_ON(tuple.TupleDataLen != 3,
-+ GOTO_ERROR_ON((tuple.TupleDataLen != 3) &&
-+ (tuple.TupleDataLen != 5),
- "bfl tpl size");
- sprom->boardflags_lo = tuple.TupleData[1] |
- ((u16)tuple.TupleData[2] << 8);
+- "bfl tpl size");
+- sprom->boardflags_lo = tuple.TupleData[1] |
+- ((u16)tuple.TupleData[2] << 8);
+- break;
+- case SSB_PCMCIA_CIS_LEDS:
+- GOTO_ERROR_ON(tuple.TupleDataLen != 5,
+- "leds tpl size");
+- sprom->gpio0 = tuple.TupleData[1];
+- sprom->gpio1 = tuple.TupleData[2];
+- sprom->gpio2 = tuple.TupleData[3];
+- sprom->gpio3 = tuple.TupleData[4];
+- break;
+- }
+- res = pcmcia_get_next_tuple(bus->host_pcmcia, &tuple);
+- if (res == -ENOSPC)
+- break;
+- GOTO_ERROR_ON(res != 0, "VEN next tpl");
+- res = pcmcia_get_tuple_data(bus->host_pcmcia, &tuple);
+- GOTO_ERROR_ON(res != 0, "VEN next tpl data");
+- }
++ res = pcmcia_loop_tuple(bus->host_pcmcia, SSB_PCMCIA_CIS,
++ ssb_pcmcia_do_get_invariants, sprom);
++ if ((res == 0) || (res == -ENOSPC))
++ return 0;
+
+- return 0;
+-error:
+ ssb_printk(KERN_ERR PFX
+- "PCMCIA: Failed to fetch device invariants: %s\n",
+- error_description);
++ "PCMCIA: Failed to fetch device invariants\n");
+ return -ENODEV;
+ }
+
--- a/include/linux/ssb/ssb.h
+++ b/include/linux/ssb/ssb.h
@@ -27,24 +27,54 @@ struct ssb_sprom {
};
/* board_vendor */
-@@ -240,8 +271,12 @@ struct ssb_bus {
+@@ -238,20 +269,33 @@ struct ssb_bus {
- /* The core in the basic address register window. (PCI bus only) */
+ const struct ssb_bus_ops *ops;
+
+- /* The core in the basic address register window. (PCI bus only) */
++ /* The core currently mapped into the MMIO window.
++ * Not valid on all host-buses. So don't use outside of SSB. */
struct ssb_device *mapped_device;
- /* Currently mapped PCMCIA segment. (bustype == SSB_BUSTYPE_PCMCIA only) */
- u8 mapped_pcmcia_seg;
/* Lock for core and segment switching.
* On PCMCIA-host busses this is used to protect the whole MMIO access. */
spinlock_t bar_lock;
-@@ -252,6 +287,11 @@ struct ssb_bus {
- struct pci_dev *host_pci;
- /* Pointer to the PCMCIA device (only if bustype == SSB_BUSTYPE_PCMCIA). */
- struct pcmcia_device *host_pcmcia;
-+ /* Pointer to the SDIO device (only if bustype == SSB_BUSTYPE_SDIO). */
-+ struct sdio_func *host_sdio;
+
+- /* The bus this backplane is running on. */
++ /* The host-bus this backplane is running on. */
+ enum ssb_bustype bustype;
+- /* Pointer to the PCI bus (only valid if bustype == SSB_BUSTYPE_PCI). */
+- struct pci_dev *host_pci;
+- /* Pointer to the PCMCIA device (only if bustype == SSB_BUSTYPE_PCMCIA). */
+- struct pcmcia_device *host_pcmcia;
++ /* Pointers to the host-bus. Check bustype before using any of these pointers. */
++ union {
++ /* Pointer to the PCI bus (only valid if bustype == SSB_BUSTYPE_PCI). */
++ struct pci_dev *host_pci;
++ /* Pointer to the PCMCIA device (only if bustype == SSB_BUSTYPE_PCMCIA). */
++ struct pcmcia_device *host_pcmcia;
++ /* Pointer to the SDIO device (only if bustype == SSB_BUSTYPE_SDIO). */
++ struct sdio_func *host_sdio;
++ };
+
+ /* See enum ssb_quirks */
+ unsigned int quirks;
#ifdef CONFIG_SSB_SPROM
/* Mutex to protect the SPROM writing. */
-@@ -306,6 +346,11 @@ struct ssb_bus {
+@@ -261,6 +305,7 @@ struct ssb_bus {
+ /* ID information about the Chip. */
+ u16 chip_id;
+ u16 chip_rev;
++ u16 sprom_offset;
+ u16 sprom_size; /* number of words in sprom */
+ u8 chip_package;
+
+@@ -306,6 +351,11 @@ struct ssb_bus {
#endif /* DEBUG */
};
/* The initialization-invariants. */
struct ssb_init_invariants {
/* Versioning information about the PCB. */
-@@ -336,6 +381,12 @@ extern int ssb_bus_pcmciabus_register(st
+@@ -336,9 +386,18 @@ extern int ssb_bus_pcmciabus_register(st
struct pcmcia_device *pcmcia_dev,
unsigned long baseaddr);
#endif /* CONFIG_SSB_PCMCIAHOST */
extern void ssb_bus_unregister(struct ssb_bus *bus);
++/* Does the device have an SPROM? */
++extern bool ssb_is_sprom_available(struct ssb_bus *bus);
++
+ /* Set a fallback SPROM.
+ * See kdoc at the function definition for complete documentation. */
+ extern int ssb_arch_set_fallback_sprom(const struct ssb_sprom *sprom);
--- a/include/linux/ssb/ssb_driver_chipcommon.h
+++ b/include/linux/ssb/ssb_driver_chipcommon.h
-@@ -629,5 +629,15 @@ extern int ssb_chipco_serial_init(struct
+@@ -53,6 +53,7 @@
+ #define SSB_CHIPCO_CAP_64BIT 0x08000000 /* 64-bit Backplane */
+ #define SSB_CHIPCO_CAP_PMU 0x10000000 /* PMU available (rev >= 20) */
+ #define SSB_CHIPCO_CAP_ECI 0x20000000 /* ECI available (rev >= 20) */
++#define SSB_CHIPCO_CAP_SPROM 0x40000000 /* SPROM present */
+ #define SSB_CHIPCO_CORECTL 0x0008
+ #define SSB_CHIPCO_CORECTL_UARTCLK0 0x00000001 /* Drive UART with internal clock */
+ #define SSB_CHIPCO_CORECTL_SE 0x00000002 /* sync clk out enable (corerev >= 3) */
+@@ -385,6 +386,7 @@
+
+
+ /** Chip specific Chip-Status register contents. */
++#define SSB_CHIPCO_CHST_4322_SPROM_EXISTS 0x00000040 /* SPROM present */
+ #define SSB_CHIPCO_CHST_4325_SPROM_OTP_SEL 0x00000003
+ #define SSB_CHIPCO_CHST_4325_DEFCIS_SEL 0 /* OTP is powered up, use def. CIS, no SPROM */
+ #define SSB_CHIPCO_CHST_4325_SPROM_SEL 1 /* OTP is powered up, SPROM is present */
+@@ -398,6 +400,18 @@
+ #define SSB_CHIPCO_CHST_4325_RCAL_VALUE_SHIFT 4
+ #define SSB_CHIPCO_CHST_4325_PMUTOP_2B 0x00000200 /* 1 for 2b, 0 for to 2a */
+
++/** Macros to determine SPROM presence based on Chip-Status register. */
++#define SSB_CHIPCO_CHST_4312_SPROM_PRESENT(status) \
++ ((status & SSB_CHIPCO_CHST_4325_SPROM_OTP_SEL) != \
++ SSB_CHIPCO_CHST_4325_OTP_SEL)
++#define SSB_CHIPCO_CHST_4322_SPROM_PRESENT(status) \
++ (status & SSB_CHIPCO_CHST_4322_SPROM_EXISTS)
++#define SSB_CHIPCO_CHST_4325_SPROM_PRESENT(status) \
++ (((status & SSB_CHIPCO_CHST_4325_SPROM_OTP_SEL) != \
++ SSB_CHIPCO_CHST_4325_DEFCIS_SEL) && \
++ ((status & SSB_CHIPCO_CHST_4325_SPROM_OTP_SEL) != \
++ SSB_CHIPCO_CHST_4325_OTP_SEL))
++
+
+
+ /** Clockcontrol masks and values **/
+@@ -564,6 +578,7 @@ struct ssb_chipcommon_pmu {
+ struct ssb_chipcommon {
+ struct ssb_device *dev;
+ u32 capabilities;
++ u32 status;
+ /* Fast Powerup Delay constant */
+ u16 fast_pwrup_delay;
+ struct ssb_chipcommon_pmu pmu;
+@@ -629,5 +644,15 @@ extern int ssb_chipco_serial_init(struct
/* PMU support */
extern void ssb_pmu_init(struct ssb_chipcommon *cc);
*/
#define SSB_SPROMSIZE_WORDS 64
#define SSB_SPROMSIZE_BYTES (SSB_SPROMSIZE_WORDS * sizeof(u16))
-@@ -327,8 +327,11 @@
+@@ -170,26 +170,27 @@
+ #define SSB_SPROMSIZE_WORDS_R4 220
+ #define SSB_SPROMSIZE_BYTES_R123 (SSB_SPROMSIZE_WORDS_R123 * sizeof(u16))
+ #define SSB_SPROMSIZE_BYTES_R4 (SSB_SPROMSIZE_WORDS_R4 * sizeof(u16))
+-#define SSB_SPROM_BASE 0x1000
+-#define SSB_SPROM_REVISION 0x107E
++#define SSB_SPROM_BASE1 0x1000
++#define SSB_SPROM_BASE31 0x0800
++#define SSB_SPROM_REVISION 0x007E
+ #define SSB_SPROM_REVISION_REV 0x00FF /* SPROM Revision number */
+ #define SSB_SPROM_REVISION_CRC 0xFF00 /* SPROM CRC8 value */
+ #define SSB_SPROM_REVISION_CRC_SHIFT 8
+
+ /* SPROM Revision 1 */
+-#define SSB_SPROM1_SPID 0x1004 /* Subsystem Product ID for PCI */
+-#define SSB_SPROM1_SVID 0x1006 /* Subsystem Vendor ID for PCI */
+-#define SSB_SPROM1_PID 0x1008 /* Product ID for PCI */
+-#define SSB_SPROM1_IL0MAC 0x1048 /* 6 bytes MAC address for 802.11b/g */
+-#define SSB_SPROM1_ET0MAC 0x104E /* 6 bytes MAC address for Ethernet */
+-#define SSB_SPROM1_ET1MAC 0x1054 /* 6 bytes MAC address for 802.11a */
+-#define SSB_SPROM1_ETHPHY 0x105A /* Ethernet PHY settings */
++#define SSB_SPROM1_SPID 0x0004 /* Subsystem Product ID for PCI */
++#define SSB_SPROM1_SVID 0x0006 /* Subsystem Vendor ID for PCI */
++#define SSB_SPROM1_PID 0x0008 /* Product ID for PCI */
++#define SSB_SPROM1_IL0MAC 0x0048 /* 6 bytes MAC address for 802.11b/g */
++#define SSB_SPROM1_ET0MAC 0x004E /* 6 bytes MAC address for Ethernet */
++#define SSB_SPROM1_ET1MAC 0x0054 /* 6 bytes MAC address for 802.11a */
++#define SSB_SPROM1_ETHPHY 0x005A /* Ethernet PHY settings */
+ #define SSB_SPROM1_ETHPHY_ET0A 0x001F /* MII Address for enet0 */
+ #define SSB_SPROM1_ETHPHY_ET1A 0x03E0 /* MII Address for enet1 */
+ #define SSB_SPROM1_ETHPHY_ET1A_SHIFT 5
+ #define SSB_SPROM1_ETHPHY_ET0M (1<<14) /* MDIO for enet0 */
+ #define SSB_SPROM1_ETHPHY_ET1M (1<<15) /* MDIO for enet1 */
+-#define SSB_SPROM1_BINF 0x105C /* Board info */
++#define SSB_SPROM1_BINF 0x005C /* Board info */
+ #define SSB_SPROM1_BINF_BREV 0x00FF /* Board Revision */
+ #define SSB_SPROM1_BINF_CCODE 0x0F00 /* Country Code */
+ #define SSB_SPROM1_BINF_CCODE_SHIFT 8
+@@ -197,63 +198,63 @@
+ #define SSB_SPROM1_BINF_ANTBG_SHIFT 12
+ #define SSB_SPROM1_BINF_ANTA 0xC000 /* Available A-PHY antennas */
+ #define SSB_SPROM1_BINF_ANTA_SHIFT 14
+-#define SSB_SPROM1_PA0B0 0x105E
+-#define SSB_SPROM1_PA0B1 0x1060
+-#define SSB_SPROM1_PA0B2 0x1062
+-#define SSB_SPROM1_GPIOA 0x1064 /* General Purpose IO pins 0 and 1 */
++#define SSB_SPROM1_PA0B0 0x005E
++#define SSB_SPROM1_PA0B1 0x0060
++#define SSB_SPROM1_PA0B2 0x0062
++#define SSB_SPROM1_GPIOA 0x0064 /* General Purpose IO pins 0 and 1 */
+ #define SSB_SPROM1_GPIOA_P0 0x00FF /* Pin 0 */
+ #define SSB_SPROM1_GPIOA_P1 0xFF00 /* Pin 1 */
+ #define SSB_SPROM1_GPIOA_P1_SHIFT 8
+-#define SSB_SPROM1_GPIOB 0x1066 /* General Purpuse IO pins 2 and 3 */
++#define SSB_SPROM1_GPIOB 0x0066 /* General Purpuse IO pins 2 and 3 */
+ #define SSB_SPROM1_GPIOB_P2 0x00FF /* Pin 2 */
+ #define SSB_SPROM1_GPIOB_P3 0xFF00 /* Pin 3 */
+ #define SSB_SPROM1_GPIOB_P3_SHIFT 8
+-#define SSB_SPROM1_MAXPWR 0x1068 /* Power Amplifier Max Power */
++#define SSB_SPROM1_MAXPWR 0x0068 /* Power Amplifier Max Power */
+ #define SSB_SPROM1_MAXPWR_BG 0x00FF /* B-PHY and G-PHY (in dBm Q5.2) */
+ #define SSB_SPROM1_MAXPWR_A 0xFF00 /* A-PHY (in dBm Q5.2) */
+ #define SSB_SPROM1_MAXPWR_A_SHIFT 8
+-#define SSB_SPROM1_PA1B0 0x106A
+-#define SSB_SPROM1_PA1B1 0x106C
+-#define SSB_SPROM1_PA1B2 0x106E
+-#define SSB_SPROM1_ITSSI 0x1070 /* Idle TSSI Target */
++#define SSB_SPROM1_PA1B0 0x006A
++#define SSB_SPROM1_PA1B1 0x006C
++#define SSB_SPROM1_PA1B2 0x006E
++#define SSB_SPROM1_ITSSI 0x0070 /* Idle TSSI Target */
+ #define SSB_SPROM1_ITSSI_BG 0x00FF /* B-PHY and G-PHY*/
+ #define SSB_SPROM1_ITSSI_A 0xFF00 /* A-PHY */
+ #define SSB_SPROM1_ITSSI_A_SHIFT 8
+-#define SSB_SPROM1_BFLLO 0x1072 /* Boardflags (low 16 bits) */
+-#define SSB_SPROM1_AGAIN 0x1074 /* Antenna Gain (in dBm Q5.2) */
++#define SSB_SPROM1_BFLLO 0x0072 /* Boardflags (low 16 bits) */
++#define SSB_SPROM1_AGAIN 0x0074 /* Antenna Gain (in dBm Q5.2) */
+ #define SSB_SPROM1_AGAIN_BG 0x00FF /* B-PHY and G-PHY */
+ #define SSB_SPROM1_AGAIN_BG_SHIFT 0
+ #define SSB_SPROM1_AGAIN_A 0xFF00 /* A-PHY */
+ #define SSB_SPROM1_AGAIN_A_SHIFT 8
+
+ /* SPROM Revision 2 (inherits from rev 1) */
+-#define SSB_SPROM2_BFLHI 0x1038 /* Boardflags (high 16 bits) */
+-#define SSB_SPROM2_MAXP_A 0x103A /* A-PHY Max Power */
++#define SSB_SPROM2_BFLHI 0x0038 /* Boardflags (high 16 bits) */
++#define SSB_SPROM2_MAXP_A 0x003A /* A-PHY Max Power */
+ #define SSB_SPROM2_MAXP_A_HI 0x00FF /* Max Power High */
+ #define SSB_SPROM2_MAXP_A_LO 0xFF00 /* Max Power Low */
+ #define SSB_SPROM2_MAXP_A_LO_SHIFT 8
+-#define SSB_SPROM2_PA1LOB0 0x103C /* A-PHY PowerAmplifier Low Settings */
+-#define SSB_SPROM2_PA1LOB1 0x103E /* A-PHY PowerAmplifier Low Settings */
+-#define SSB_SPROM2_PA1LOB2 0x1040 /* A-PHY PowerAmplifier Low Settings */
+-#define SSB_SPROM2_PA1HIB0 0x1042 /* A-PHY PowerAmplifier High Settings */
+-#define SSB_SPROM2_PA1HIB1 0x1044 /* A-PHY PowerAmplifier High Settings */
+-#define SSB_SPROM2_PA1HIB2 0x1046 /* A-PHY PowerAmplifier High Settings */
+-#define SSB_SPROM2_OPO 0x1078 /* OFDM Power Offset from CCK Level */
++#define SSB_SPROM2_PA1LOB0 0x003C /* A-PHY PowerAmplifier Low Settings */
++#define SSB_SPROM2_PA1LOB1 0x003E /* A-PHY PowerAmplifier Low Settings */
++#define SSB_SPROM2_PA1LOB2 0x0040 /* A-PHY PowerAmplifier Low Settings */
++#define SSB_SPROM2_PA1HIB0 0x0042 /* A-PHY PowerAmplifier High Settings */
++#define SSB_SPROM2_PA1HIB1 0x0044 /* A-PHY PowerAmplifier High Settings */
++#define SSB_SPROM2_PA1HIB2 0x0046 /* A-PHY PowerAmplifier High Settings */
++#define SSB_SPROM2_OPO 0x0078 /* OFDM Power Offset from CCK Level */
+ #define SSB_SPROM2_OPO_VALUE 0x00FF
+ #define SSB_SPROM2_OPO_UNUSED 0xFF00
+-#define SSB_SPROM2_CCODE 0x107C /* Two char Country Code */
++#define SSB_SPROM2_CCODE 0x007C /* Two char Country Code */
+
+ /* SPROM Revision 3 (inherits most data from rev 2) */
+-#define SSB_SPROM3_IL0MAC 0x104A /* 6 bytes MAC address for 802.11b/g */
+-#define SSB_SPROM3_OFDMAPO 0x102C /* A-PHY OFDM Mid Power Offset (4 bytes, BigEndian) */
+-#define SSB_SPROM3_OFDMALPO 0x1030 /* A-PHY OFDM Low Power Offset (4 bytes, BigEndian) */
+-#define SSB_SPROM3_OFDMAHPO 0x1034 /* A-PHY OFDM High Power Offset (4 bytes, BigEndian) */
+-#define SSB_SPROM3_GPIOLDC 0x1042 /* GPIO LED Powersave Duty Cycle (4 bytes, BigEndian) */
++#define SSB_SPROM3_OFDMAPO 0x002C /* A-PHY OFDM Mid Power Offset (4 bytes, BigEndian) */
++#define SSB_SPROM3_OFDMALPO 0x0030 /* A-PHY OFDM Low Power Offset (4 bytes, BigEndian) */
++#define SSB_SPROM3_OFDMAHPO 0x0034 /* A-PHY OFDM High Power Offset (4 bytes, BigEndian) */
++#define SSB_SPROM3_GPIOLDC 0x0042 /* GPIO LED Powersave Duty Cycle (4 bytes, BigEndian) */
+ #define SSB_SPROM3_GPIOLDC_OFF 0x0000FF00 /* Off Count */
+ #define SSB_SPROM3_GPIOLDC_OFF_SHIFT 8
+ #define SSB_SPROM3_GPIOLDC_ON 0x00FF0000 /* On Count */
+ #define SSB_SPROM3_GPIOLDC_ON_SHIFT 16
+-#define SSB_SPROM3_CCKPO 0x1078 /* CCK Power Offset */
++#define SSB_SPROM3_IL0MAC 0x004A /* 6 bytes MAC address for 802.11b/g */
++#define SSB_SPROM3_CCKPO 0x0078 /* CCK Power Offset */
+ #define SSB_SPROM3_CCKPO_1M 0x000F /* 1M Rate PO */
+ #define SSB_SPROM3_CCKPO_2M 0x00F0 /* 2M Rate PO */
+ #define SSB_SPROM3_CCKPO_2M_SHIFT 4
+@@ -264,104 +265,156 @@
+ #define SSB_SPROM3_OFDMGPO 0x107A /* G-PHY OFDM Power Offset (4 bytes, BigEndian) */
+
+ /* SPROM Revision 4 */
+-#define SSB_SPROM4_IL0MAC 0x104C /* 6 byte MAC address for a/b/g/n */
+-#define SSB_SPROM4_ETHPHY 0x105A /* Ethernet PHY settings ?? */
++#define SSB_SPROM4_BFLLO 0x0044 /* Boardflags (low 16 bits) */
++#define SSB_SPROM4_BFLHI 0x0046 /* Board Flags Hi */
++#define SSB_SPROM4_IL0MAC 0x004C /* 6 byte MAC address for a/b/g/n */
++#define SSB_SPROM4_CCODE 0x0052 /* Country Code (2 bytes) */
++#define SSB_SPROM4_GPIOA 0x0056 /* Gen. Purpose IO # 0 and 1 */
++#define SSB_SPROM4_GPIOA_P0 0x00FF /* Pin 0 */
++#define SSB_SPROM4_GPIOA_P1 0xFF00 /* Pin 1 */
++#define SSB_SPROM4_GPIOA_P1_SHIFT 8
++#define SSB_SPROM4_GPIOB 0x0058 /* Gen. Purpose IO # 2 and 3 */
++#define SSB_SPROM4_GPIOB_P2 0x00FF /* Pin 2 */
++#define SSB_SPROM4_GPIOB_P3 0xFF00 /* Pin 3 */
++#define SSB_SPROM4_GPIOB_P3_SHIFT 8
++#define SSB_SPROM4_ETHPHY 0x005A /* Ethernet PHY settings ?? */
+ #define SSB_SPROM4_ETHPHY_ET0A 0x001F /* MII Address for enet0 */
+ #define SSB_SPROM4_ETHPHY_ET1A 0x03E0 /* MII Address for enet1 */
+ #define SSB_SPROM4_ETHPHY_ET1A_SHIFT 5
+ #define SSB_SPROM4_ETHPHY_ET0M (1<<14) /* MDIO for enet0 */
+ #define SSB_SPROM4_ETHPHY_ET1M (1<<15) /* MDIO for enet1 */
+-#define SSB_SPROM4_CCODE 0x1052 /* Country Code (2 bytes) */
+-#define SSB_SPROM4_ANTAVAIL 0x105D /* Antenna available bitfields */
+-#define SSB_SPROM4_ANTAVAIL_A 0x00FF /* A-PHY bitfield */
+-#define SSB_SPROM4_ANTAVAIL_A_SHIFT 0
+-#define SSB_SPROM4_ANTAVAIL_BG 0xFF00 /* B-PHY and G-PHY bitfield */
+-#define SSB_SPROM4_ANTAVAIL_BG_SHIFT 8
+-#define SSB_SPROM4_BFLLO 0x1044 /* Boardflags (low 16 bits) */
+-#define SSB_SPROM4_AGAIN01 0x105E /* Antenna Gain (in dBm Q5.2) */
++#define SSB_SPROM4_ANTAVAIL 0x005D /* Antenna available bitfields */
++#define SSB_SPROM4_ANTAVAIL_A 0x00FF /* A-PHY bitfield */
++#define SSB_SPROM4_ANTAVAIL_A_SHIFT 0
++#define SSB_SPROM4_ANTAVAIL_BG 0xFF00 /* B-PHY and G-PHY bitfield */
++#define SSB_SPROM4_ANTAVAIL_BG_SHIFT 8
++#define SSB_SPROM4_AGAIN01 0x005E /* Antenna Gain (in dBm Q5.2) */
+ #define SSB_SPROM4_AGAIN0 0x00FF /* Antenna 0 */
+ #define SSB_SPROM4_AGAIN0_SHIFT 0
+ #define SSB_SPROM4_AGAIN1 0xFF00 /* Antenna 1 */
+ #define SSB_SPROM4_AGAIN1_SHIFT 8
+-#define SSB_SPROM4_AGAIN23 0x1060
++#define SSB_SPROM4_AGAIN23 0x0060
+ #define SSB_SPROM4_AGAIN2 0x00FF /* Antenna 2 */
+ #define SSB_SPROM4_AGAIN2_SHIFT 0
+ #define SSB_SPROM4_AGAIN3 0xFF00 /* Antenna 3 */
+ #define SSB_SPROM4_AGAIN3_SHIFT 8
+-#define SSB_SPROM4_BFLHI 0x1046 /* Board Flags Hi */
+-#define SSB_SPROM4_MAXP_BG 0x1080 /* Max Power BG in path 1 */
++#define SSB_SPROM4_MAXP_BG 0x0080 /* Max Power BG in path 1 */
+ #define SSB_SPROM4_MAXP_BG_MASK 0x00FF /* Mask for Max Power BG */
+ #define SSB_SPROM4_ITSSI_BG 0xFF00 /* Mask for path 1 itssi_bg */
+ #define SSB_SPROM4_ITSSI_BG_SHIFT 8
+-#define SSB_SPROM4_MAXP_A 0x108A /* Max Power A in path 1 */
++#define SSB_SPROM4_MAXP_A 0x008A /* Max Power A in path 1 */
+ #define SSB_SPROM4_MAXP_A_MASK 0x00FF /* Mask for Max Power A */
+ #define SSB_SPROM4_ITSSI_A 0xFF00 /* Mask for path 1 itssi_a */
+ #define SSB_SPROM4_ITSSI_A_SHIFT 8
+-#define SSB_SPROM4_GPIOA 0x1056 /* Gen. Purpose IO # 0 and 1 */
+-#define SSB_SPROM4_GPIOA_P0 0x00FF /* Pin 0 */
+-#define SSB_SPROM4_GPIOA_P1 0xFF00 /* Pin 1 */
+-#define SSB_SPROM4_GPIOA_P1_SHIFT 8
+-#define SSB_SPROM4_GPIOB 0x1058 /* Gen. Purpose IO # 2 and 3 */
+-#define SSB_SPROM4_GPIOB_P2 0x00FF /* Pin 2 */
+-#define SSB_SPROM4_GPIOB_P3 0xFF00 /* Pin 3 */
+-#define SSB_SPROM4_GPIOB_P3_SHIFT 8
+-#define SSB_SPROM4_PA0B0 0x1082 /* The paXbY locations are */
+-#define SSB_SPROM4_PA0B1 0x1084 /* only guesses */
+-#define SSB_SPROM4_PA0B2 0x1086
+-#define SSB_SPROM4_PA1B0 0x108E
+-#define SSB_SPROM4_PA1B1 0x1090
+-#define SSB_SPROM4_PA1B2 0x1092
++#define SSB_SPROM4_PA0B0 0x0082 /* The paXbY locations are */
++#define SSB_SPROM4_PA0B1 0x0084 /* only guesses */
++#define SSB_SPROM4_PA0B2 0x0086
++#define SSB_SPROM4_PA1B0 0x008E
++#define SSB_SPROM4_PA1B1 0x0090
++#define SSB_SPROM4_PA1B2 0x0092
+
+ /* SPROM Revision 5 (inherits most data from rev 4) */
+-#define SSB_SPROM5_BFLLO 0x104A /* Boardflags (low 16 bits) */
+-#define SSB_SPROM5_BFLHI 0x104C /* Board Flags Hi */
+-#define SSB_SPROM5_IL0MAC 0x1052 /* 6 byte MAC address for a/b/g/n */
+-#define SSB_SPROM5_CCODE 0x1044 /* Country Code (2 bytes) */
+-#define SSB_SPROM5_GPIOA 0x1076 /* Gen. Purpose IO # 0 and 1 */
++#define SSB_SPROM5_CCODE 0x0044 /* Country Code (2 bytes) */
++#define SSB_SPROM5_BFLLO 0x004A /* Boardflags (low 16 bits) */
++#define SSB_SPROM5_BFLHI 0x004C /* Board Flags Hi */
++#define SSB_SPROM5_IL0MAC 0x0052 /* 6 byte MAC address for a/b/g/n */
++#define SSB_SPROM5_GPIOA 0x0076 /* Gen. Purpose IO # 0 and 1 */
+ #define SSB_SPROM5_GPIOA_P0 0x00FF /* Pin 0 */
+ #define SSB_SPROM5_GPIOA_P1 0xFF00 /* Pin 1 */
+ #define SSB_SPROM5_GPIOA_P1_SHIFT 8
+-#define SSB_SPROM5_GPIOB 0x1078 /* Gen. Purpose IO # 2 and 3 */
++#define SSB_SPROM5_GPIOB 0x0078 /* Gen. Purpose IO # 2 and 3 */
+ #define SSB_SPROM5_GPIOB_P2 0x00FF /* Pin 2 */
+ #define SSB_SPROM5_GPIOB_P3 0xFF00 /* Pin 3 */
#define SSB_SPROM5_GPIOB_P3_SHIFT 8
/* SPROM Revision 8 */
-#define SSB_SPROM8_BFLLO 0x1084 /* Boardflags (low 16 bits) */
-#define SSB_SPROM8_BFLHI 0x1086 /* Boardflags Hi */
-+#define SSB_SPROM8_BOARDREV 0x1082 /* Board revision */
-+#define SSB_SPROM8_BFLLO 0x1084 /* Board flags (bits 0-15) */
-+#define SSB_SPROM8_BFLHI 0x1086 /* Board flags (bits 16-31) */
-+#define SSB_SPROM8_BFL2LO 0x1088 /* Board flags (bits 32-47) */
-+#define SSB_SPROM8_BFL2HI 0x108A /* Board flags (bits 48-63) */
- #define SSB_SPROM8_IL0MAC 0x108C /* 6 byte MAC address */
- #define SSB_SPROM8_CCODE 0x1092 /* 2 byte country code */
- #define SSB_SPROM8_ANTAVAIL 0x109C /* Antenna available bitfields*/
-@@ -354,14 +357,63 @@
- #define SSB_SPROM8_GPIOB_P2 0x00FF /* Pin 2 */
- #define SSB_SPROM8_GPIOB_P3 0xFF00 /* Pin 3 */
- #define SSB_SPROM8_GPIOB_P3_SHIFT 8
+-#define SSB_SPROM8_IL0MAC 0x108C /* 6 byte MAC address */
+-#define SSB_SPROM8_CCODE 0x1092 /* 2 byte country code */
+-#define SSB_SPROM8_ANTAVAIL 0x109C /* Antenna available bitfields*/
+-#define SSB_SPROM8_ANTAVAIL_A 0xFF00 /* A-PHY bitfield */
+-#define SSB_SPROM8_ANTAVAIL_A_SHIFT 8
+-#define SSB_SPROM8_ANTAVAIL_BG 0x00FF /* B-PHY and G-PHY bitfield */
+-#define SSB_SPROM8_ANTAVAIL_BG_SHIFT 0
+-#define SSB_SPROM8_AGAIN01 0x109E /* Antenna Gain (in dBm Q5.2) */
++#define SSB_SPROM8_BOARDREV 0x0082 /* Board revision */
++#define SSB_SPROM8_BFLLO 0x0084 /* Board flags (bits 0-15) */
++#define SSB_SPROM8_BFLHI 0x0086 /* Board flags (bits 16-31) */
++#define SSB_SPROM8_BFL2LO 0x0088 /* Board flags (bits 32-47) */
++#define SSB_SPROM8_BFL2HI 0x008A /* Board flags (bits 48-63) */
++#define SSB_SPROM8_IL0MAC 0x008C /* 6 byte MAC address */
++#define SSB_SPROM8_CCODE 0x0092 /* 2 byte country code */
++#define SSB_SPROM8_GPIOA 0x0096 /*Gen. Purpose IO # 0 and 1 */
++#define SSB_SPROM8_GPIOA_P0 0x00FF /* Pin 0 */
++#define SSB_SPROM8_GPIOA_P1 0xFF00 /* Pin 1 */
++#define SSB_SPROM8_GPIOA_P1_SHIFT 8
++#define SSB_SPROM8_GPIOB 0x0098 /* Gen. Purpose IO # 2 and 3 */
++#define SSB_SPROM8_GPIOB_P2 0x00FF /* Pin 2 */
++#define SSB_SPROM8_GPIOB_P3 0xFF00 /* Pin 3 */
++#define SSB_SPROM8_GPIOB_P3_SHIFT 8
++#define SSB_SPROM8_ANTAVAIL 0x009C /* Antenna available bitfields*/
++#define SSB_SPROM8_ANTAVAIL_A 0xFF00 /* A-PHY bitfield */
++#define SSB_SPROM8_ANTAVAIL_A_SHIFT 8
++#define SSB_SPROM8_ANTAVAIL_BG 0x00FF /* B-PHY and G-PHY bitfield */
++#define SSB_SPROM8_ANTAVAIL_BG_SHIFT 0
++#define SSB_SPROM8_AGAIN01 0x009E /* Antenna Gain (in dBm Q5.2) */
+ #define SSB_SPROM8_AGAIN0 0x00FF /* Antenna 0 */
+ #define SSB_SPROM8_AGAIN0_SHIFT 0
+ #define SSB_SPROM8_AGAIN1 0xFF00 /* Antenna 1 */
+ #define SSB_SPROM8_AGAIN1_SHIFT 8
+-#define SSB_SPROM8_AGAIN23 0x10A0
++#define SSB_SPROM8_AGAIN23 0x00A0
+ #define SSB_SPROM8_AGAIN2 0x00FF /* Antenna 2 */
+ #define SSB_SPROM8_AGAIN2_SHIFT 0
+ #define SSB_SPROM8_AGAIN3 0xFF00 /* Antenna 3 */
+ #define SSB_SPROM8_AGAIN3_SHIFT 8
+-#define SSB_SPROM8_GPIOA 0x1096 /*Gen. Purpose IO # 0 and 1 */
+-#define SSB_SPROM8_GPIOA_P0 0x00FF /* Pin 0 */
+-#define SSB_SPROM8_GPIOA_P1 0xFF00 /* Pin 1 */
+-#define SSB_SPROM8_GPIOA_P1_SHIFT 8
+-#define SSB_SPROM8_GPIOB 0x1098 /* Gen. Purpose IO # 2 and 3 */
+-#define SSB_SPROM8_GPIOB_P2 0x00FF /* Pin 2 */
+-#define SSB_SPROM8_GPIOB_P3 0xFF00 /* Pin 3 */
+-#define SSB_SPROM8_GPIOB_P3_SHIFT 8
-#define SSB_SPROM8_MAXP_BG 0x10C0 /* Max Power BG in path 1 */
-#define SSB_SPROM8_MAXP_BG_MASK 0x00FF /* Mask for Max Power BG */
-+#define SSB_SPROM8_RSSIPARM2G 0x10A4 /* RSSI params for 2GHz */
++#define SSB_SPROM8_RSSIPARM2G 0x00A4 /* RSSI params for 2GHz */
+#define SSB_SPROM8_RSSISMF2G 0x000F
+#define SSB_SPROM8_RSSISMC2G 0x00F0
+#define SSB_SPROM8_RSSISMC2G_SHIFT 4
+#define SSB_SPROM8_RSSISAV2G_SHIFT 8
+#define SSB_SPROM8_BXA2G 0x1800
+#define SSB_SPROM8_BXA2G_SHIFT 11
-+#define SSB_SPROM8_RSSIPARM5G 0x10A6 /* RSSI params for 5GHz */
++#define SSB_SPROM8_RSSIPARM5G 0x00A6 /* RSSI params for 5GHz */
+#define SSB_SPROM8_RSSISMF5G 0x000F
+#define SSB_SPROM8_RSSISMC5G 0x00F0
+#define SSB_SPROM8_RSSISMC5G_SHIFT 4
+#define SSB_SPROM8_RSSISAV5G_SHIFT 8
+#define SSB_SPROM8_BXA5G 0x1800
+#define SSB_SPROM8_BXA5G_SHIFT 11
-+#define SSB_SPROM8_TRI25G 0x10A8 /* TX isolation 2.4&5.3GHz */
++#define SSB_SPROM8_TRI25G 0x00A8 /* TX isolation 2.4&5.3GHz */
+#define SSB_SPROM8_TRI2G 0x00FF /* TX isolation 2.4GHz */
+#define SSB_SPROM8_TRI5G 0xFF00 /* TX isolation 5.3GHz */
+#define SSB_SPROM8_TRI5G_SHIFT 8
-+#define SSB_SPROM8_TRI5GHL 0x10AA /* TX isolation 5.2/5.8GHz */
++#define SSB_SPROM8_TRI5GHL 0x00AA /* TX isolation 5.2/5.8GHz */
+#define SSB_SPROM8_TRI5GL 0x00FF /* TX isolation 5.2GHz */
+#define SSB_SPROM8_TRI5GH 0xFF00 /* TX isolation 5.8GHz */
+#define SSB_SPROM8_TRI5GH_SHIFT 8
-+#define SSB_SPROM8_RXPO 0x10AC /* RX power offsets */
++#define SSB_SPROM8_RXPO 0x00AC /* RX power offsets */
+#define SSB_SPROM8_RXPO2G 0x00FF /* 2GHz RX power offset */
+#define SSB_SPROM8_RXPO5G 0xFF00 /* 5GHz RX power offset */
+#define SSB_SPROM8_RXPO5G_SHIFT 8
-+#define SSB_SPROM8_MAXP_BG 0x10C0 /* Max Power 2GHz in path 1 */
++#define SSB_SPROM8_MAXP_BG 0x00C0 /* Max Power 2GHz in path 1 */
+#define SSB_SPROM8_MAXP_BG_MASK 0x00FF /* Mask for Max Power 2GHz */
#define SSB_SPROM8_ITSSI_BG 0xFF00 /* Mask for path 1 itssi_bg */
#define SSB_SPROM8_ITSSI_BG_SHIFT 8
-#define SSB_SPROM8_MAXP_A 0x10C8 /* Max Power A in path 1 */
-#define SSB_SPROM8_MAXP_A_MASK 0x00FF /* Mask for Max Power A */
-+#define SSB_SPROM8_PA0B0 0x10C2 /* 2GHz power amp settings */
-+#define SSB_SPROM8_PA0B1 0x10C4
-+#define SSB_SPROM8_PA0B2 0x10C6
-+#define SSB_SPROM8_MAXP_A 0x10C8 /* Max Power 5.3GHz */
++#define SSB_SPROM8_PA0B0 0x00C2 /* 2GHz power amp settings */
++#define SSB_SPROM8_PA0B1 0x00C4
++#define SSB_SPROM8_PA0B2 0x00C6
++#define SSB_SPROM8_MAXP_A 0x00C8 /* Max Power 5.3GHz */
+#define SSB_SPROM8_MAXP_A_MASK 0x00FF /* Mask for Max Power 5.3GHz */
#define SSB_SPROM8_ITSSI_A 0xFF00 /* Mask for path 1 itssi_a */
#define SSB_SPROM8_ITSSI_A_SHIFT 8
-+#define SSB_SPROM8_MAXP_AHL 0x10CA /* Max Power 5.2/5.8GHz */
++#define SSB_SPROM8_MAXP_AHL 0x00CA /* Max Power 5.2/5.8GHz */
+#define SSB_SPROM8_MAXP_AH_MASK 0x00FF /* Mask for Max Power 5.8GHz */
+#define SSB_SPROM8_MAXP_AL_MASK 0xFF00 /* Mask for Max Power 5.2GHz */
+#define SSB_SPROM8_MAXP_AL_SHIFT 8
-+#define SSB_SPROM8_PA1B0 0x10CC /* 5.3GHz power amp settings */
-+#define SSB_SPROM8_PA1B1 0x10CE
-+#define SSB_SPROM8_PA1B2 0x10D0
-+#define SSB_SPROM8_PA1LOB0 0x10D2 /* 5.2GHz power amp settings */
-+#define SSB_SPROM8_PA1LOB1 0x10D4
-+#define SSB_SPROM8_PA1LOB2 0x10D6
-+#define SSB_SPROM8_PA1HIB0 0x10D8 /* 5.8GHz power amp settings */
-+#define SSB_SPROM8_PA1HIB1 0x10DA
-+#define SSB_SPROM8_PA1HIB2 0x10DC
-+#define SSB_SPROM8_CCK2GPO 0x1140 /* CCK power offset */
-+#define SSB_SPROM8_OFDM2GPO 0x1142 /* 2.4GHz OFDM power offset */
-+#define SSB_SPROM8_OFDM5GPO 0x1146 /* 5.3GHz OFDM power offset */
-+#define SSB_SPROM8_OFDM5GLPO 0x114A /* 5.2GHz OFDM power offset */
-+#define SSB_SPROM8_OFDM5GHPO 0x114E /* 5.8GHz OFDM power offset */
++#define SSB_SPROM8_PA1B0 0x00CC /* 5.3GHz power amp settings */
++#define SSB_SPROM8_PA1B1 0x00CE
++#define SSB_SPROM8_PA1B2 0x00D0
++#define SSB_SPROM8_PA1LOB0 0x00D2 /* 5.2GHz power amp settings */
++#define SSB_SPROM8_PA1LOB1 0x00D4
++#define SSB_SPROM8_PA1LOB2 0x00D6
++#define SSB_SPROM8_PA1HIB0 0x00D8 /* 5.8GHz power amp settings */
++#define SSB_SPROM8_PA1HIB1 0x00DA
++#define SSB_SPROM8_PA1HIB2 0x00DC
++#define SSB_SPROM8_CCK2GPO 0x0140 /* CCK power offset */
++#define SSB_SPROM8_OFDM2GPO 0x0142 /* 2.4GHz OFDM power offset */
++#define SSB_SPROM8_OFDM5GPO 0x0146 /* 5.3GHz OFDM power offset */
++#define SSB_SPROM8_OFDM5GLPO 0x014A /* 5.2GHz OFDM power offset */
++#define SSB_SPROM8_OFDM5GHPO 0x014E /* 5.8GHz OFDM power offset */
/* Values for SSB_SPROM1_BINF_CCODE */
enum {
--- a/drivers/ssb/scan.c
+++ b/drivers/ssb/scan.c
-@@ -175,6 +175,8 @@ static u32 scan_read32(struct ssb_bus *b
+@@ -162,6 +162,8 @@ static u8 chipid_to_nrcores(u16 chipid)
+ static u32 scan_read32(struct ssb_bus *bus, u8 current_coreidx,
+ u16 offset)
+ {
++ u32 lo, hi;
++
+ switch (bus->bustype) {
+ case SSB_BUSTYPE_SSB:
+ offset += current_coreidx * SSB_CORE_SIZE;
+@@ -174,6 +176,10 @@ static u32 scan_read32(struct ssb_bus *b
+ offset -= 0x800;
} else
ssb_pcmcia_switch_segment(bus, 0);
- break;
++ lo = readw(bus->mmio + offset);
++ hi = readw(bus->mmio + offset + 2);
++ return lo | (hi << 16);
+ default:
-+ break;
+ break;
}
return readl(bus->mmio + offset);
- }
-@@ -188,6 +190,8 @@ static int scan_switchcore(struct ssb_bu
+@@ -188,6 +194,8 @@ static int scan_switchcore(struct ssb_bu
return ssb_pci_switch_coreidx(bus, coreidx);
case SSB_BUSTYPE_PCMCIA:
return ssb_pcmcia_switch_coreidx(bus, coreidx);
}
return 0;
}
-@@ -206,6 +210,8 @@ void ssb_iounmap(struct ssb_bus *bus)
+@@ -206,6 +214,8 @@ void ssb_iounmap(struct ssb_bus *bus)
SSB_BUG_ON(1); /* Can't reach this code. */
#endif
break;
}
bus->mmio = NULL;
bus->mapped_device = NULL;
-@@ -230,6 +236,8 @@ static void __iomem *ssb_ioremap(struct
+@@ -230,6 +240,8 @@ static void __iomem *ssb_ioremap(struct
SSB_BUG_ON(1); /* Can't reach this code. */
#endif
break;
}
return mmio;
+@@ -339,7 +351,7 @@ int ssb_bus_scan(struct ssb_bus *bus,
+ dev->bus = bus;
+ dev->ops = bus->ops;
+
+- ssb_dprintk(KERN_INFO PFX
++ printk(KERN_DEBUG PFX
+ "Core %d found: %s "
+ "(cc 0x%03X, rev 0x%02X, vendor 0x%04X)\n",
+ i, ssb_core_name(dev->id.coreid),
+--- a/drivers/ssb/driver_chipcommon.c
++++ b/drivers/ssb/driver_chipcommon.c
+@@ -233,6 +233,8 @@ void ssb_chipcommon_init(struct ssb_chip
+ {
+ if (!cc->dev)
+ return; /* We don't have a ChipCommon */
++ if (cc->dev->id.revision >= 11)
++ cc->status = chipco_read32(cc, SSB_CHIPCO_CHIPSTAT);
+ ssb_pmu_init(cc);
+ chipco_powercontrol_init(cc);
+ ssb_chipco_set_clockmode(cc, SSB_CLKMODE_FAST);
+@@ -370,6 +372,7 @@ u32 ssb_chipco_gpio_control(struct ssb_c
+ {
+ return chipco_write32_masked(cc, SSB_CHIPCO_GPIOCTL, mask, value);
+ }
++EXPORT_SYMBOL(ssb_chipco_gpio_control);
+
+ u32 ssb_chipco_gpio_intmask(struct ssb_chipcommon *cc, u32 mask, u32 value)
+ {
+--- a/drivers/ssb/driver_mipscore.c
++++ b/drivers/ssb/driver_mipscore.c
+@@ -49,29 +49,54 @@ static const u32 ipsflag_irq_shift[] = {
+
+ static inline u32 ssb_irqflag(struct ssb_device *dev)
+ {
+- return ssb_read32(dev, SSB_TPSFLAG) & SSB_TPSFLAG_BPFLAG;
++ u32 tpsflag = ssb_read32(dev, SSB_TPSFLAG);
++ if (tpsflag)
++ return ssb_read32(dev, SSB_TPSFLAG) & SSB_TPSFLAG_BPFLAG;
++ else
++ /* not irq supported */
++ return 0x3f;
++}
++
++static struct ssb_device *find_device(struct ssb_device *rdev, int irqflag)
++{
++ struct ssb_bus *bus = rdev->bus;
++ int i;
++ for (i = 0; i < bus->nr_devices; i++) {
++ struct ssb_device *dev;
++ dev = &(bus->devices[i]);
++ if (ssb_irqflag(dev) == irqflag)
++ return dev;
++ }
++ return NULL;
+ }
+
+ /* Get the MIPS IRQ assignment for a specified device.
+ * If unassigned, 0 is returned.
++ * If disabled, 5 is returned.
++ * If not supported, 6 is returned.
+ */
+ unsigned int ssb_mips_irq(struct ssb_device *dev)
+ {
+ struct ssb_bus *bus = dev->bus;
++ struct ssb_device *mdev = bus->mipscore.dev;
+ u32 irqflag;
+ u32 ipsflag;
+ u32 tmp;
+ unsigned int irq;
+
+ irqflag = ssb_irqflag(dev);
++ if (irqflag == 0x3f)
++ return 6;
+ ipsflag = ssb_read32(bus->mipscore.dev, SSB_IPSFLAG);
+ for (irq = 1; irq <= 4; irq++) {
+ tmp = ((ipsflag & ipsflag_irq_mask[irq]) >> ipsflag_irq_shift[irq]);
+ if (tmp == irqflag)
+ break;
+ }
+- if (irq == 5)
+- irq = 0;
++ if (irq == 5) {
++ if ((1 << irqflag) & ssb_read32(mdev, SSB_INTVEC))
++ irq = 0;
++ }
+
+ return irq;
+ }
+@@ -97,25 +122,56 @@ static void set_irq(struct ssb_device *d
+ struct ssb_device *mdev = bus->mipscore.dev;
+ u32 irqflag = ssb_irqflag(dev);
+
++ BUG_ON(oldirq == 6);
++
+ dev->irq = irq + 2;
+
+- ssb_dprintk(KERN_INFO PFX
+- "set_irq: core 0x%04x, irq %d => %d\n",
+- dev->id.coreid, oldirq, irq);
+ /* clear the old irq */
+ if (oldirq == 0)
+ ssb_write32(mdev, SSB_INTVEC, (~(1 << irqflag) & ssb_read32(mdev, SSB_INTVEC)));
+- else
++ else if (oldirq != 5)
+ clear_irq(bus, oldirq);
+
+ /* assign the new one */
+ if (irq == 0) {
+ ssb_write32(mdev, SSB_INTVEC, ((1 << irqflag) | ssb_read32(mdev, SSB_INTVEC)));
+ } else {
++ u32 ipsflag = ssb_read32(mdev, SSB_IPSFLAG);
++ if ((ipsflag & ipsflag_irq_mask[irq]) != ipsflag_irq_mask[irq]) {
++ u32 oldipsflag = (ipsflag & ipsflag_irq_mask[irq]) >> ipsflag_irq_shift[irq];
++ struct ssb_device *olddev = find_device(dev, oldipsflag);
++ if (olddev)
++ set_irq(olddev, 0);
++ }
+ irqflag <<= ipsflag_irq_shift[irq];
+- irqflag |= (ssb_read32(mdev, SSB_IPSFLAG) & ~ipsflag_irq_mask[irq]);
++ irqflag |= (ipsflag & ~ipsflag_irq_mask[irq]);
+ ssb_write32(mdev, SSB_IPSFLAG, irqflag);
+ }
++ ssb_dprintk(KERN_INFO PFX
++ "set_irq: core 0x%04x, irq %d => %d\n",
++ dev->id.coreid, oldirq+2, irq+2);
++}
++
++static void print_irq(struct ssb_device *dev, unsigned int irq)
++{
++ int i;
++ static const char *irq_name[] = {"2(S)", "3", "4", "5", "6", "D", "I"};
++ ssb_dprintk(KERN_INFO PFX
++ "core 0x%04x, irq :", dev->id.coreid);
++ for (i = 0; i <= 6; i++) {
++ ssb_dprintk(" %s%s", irq_name[i], i==irq?"*":" ");
++ }
++ ssb_dprintk("\n");
++}
++
++static void dump_irq(struct ssb_bus *bus)
++{
++ int i;
++ for (i = 0; i < bus->nr_devices; i++) {
++ struct ssb_device *dev;
++ dev = &(bus->devices[i]);
++ print_irq(dev, ssb_mips_irq(dev));
++ }
+ }
+
+ static void ssb_mips_serial_init(struct ssb_mipscore *mcore)
+@@ -197,17 +253,23 @@ void ssb_mipscore_init(struct ssb_mipsco
+
+ /* Assign IRQs to all cores on the bus, start with irq line 2, because serial usually takes 1 */
+ for (irq = 2, i = 0; i < bus->nr_devices; i++) {
++ int mips_irq;
+ dev = &(bus->devices[i]);
+- dev->irq = ssb_mips_irq(dev) + 2;
++ mips_irq = ssb_mips_irq(dev);
++ if (mips_irq > 4)
++ dev->irq = 0;
++ else
++ dev->irq = mips_irq + 2;
++ if (dev->irq > 5)
++ continue;
+ switch (dev->id.coreid) {
+ case SSB_DEV_USB11_HOST:
+ /* shouldn't need a separate irq line for non-4710, most of them have a proper
+ * external usb controller on the pci */
+ if ((bus->chip_id == 0x4710) && (irq <= 4)) {
+ set_irq(dev, irq++);
+- break;
+ }
+- /* fallthrough */
++ break;
+ case SSB_DEV_PCI:
+ case SSB_DEV_ETHERNET:
+ case SSB_DEV_ETHERNET_GBIT:
+@@ -218,8 +280,14 @@ void ssb_mipscore_init(struct ssb_mipsco
+ set_irq(dev, irq++);
+ break;
+ }
++ /* fallthrough */
++ case SSB_DEV_EXTIF:
++ set_irq(dev, 0);
++ break;
+ }
+ }
++ ssb_dprintk(KERN_INFO PFX "after irq reconfiguration\n");
++ dump_irq(bus);
+
+ ssb_mips_serial_init(mcore);
+ ssb_mips_flash_detect(mcore);
+--- a/drivers/ssb/sprom.c
++++ b/drivers/ssb/sprom.c
+@@ -13,6 +13,9 @@
+
+ #include "ssb_private.h"
+
++#include <linux/ctype.h>
++#include <linux/slab.h>
++
+
+ static const struct ssb_sprom *fallback_sprom;
+
+@@ -33,17 +36,27 @@ static int sprom2hex(const u16 *sprom, c
+ static int hex2sprom(u16 *sprom, const char *dump, size_t len,
+ size_t sprom_size_words)
+ {
+- char tmp[5] = { 0 };
+- int cnt = 0;
++ char c, tmp[5] = { 0 };
++ int err, cnt = 0;
+ unsigned long parsed;
+
+- if (len < sprom_size_words * 2)
++ /* Strip whitespace at the end. */
++ while (len) {
++ c = dump[len - 1];
++ if (!isspace(c) && c != '\0')
++ break;
++ len--;
++ }
++ /* Length must match exactly. */
++ if (len != sprom_size_words * 4)
+ return -EINVAL;
+
+ while (cnt < sprom_size_words) {
+ memcpy(tmp, dump, 4);
+ dump += 4;
+- parsed = simple_strtoul(tmp, NULL, 16);
++ err = strict_strtoul(tmp, 16, &parsed);
++ if (err)
++ return err;
+ sprom[cnt++] = swab16((u16)parsed);
+ }
+
+@@ -90,6 +103,7 @@ ssize_t ssb_attr_sprom_store(struct ssb_
+ u16 *sprom;
+ int res = 0, err = -ENOMEM;
+ size_t sprom_size_words = bus->sprom_size;
++ struct ssb_freeze_context freeze;
+
+ sprom = kcalloc(bus->sprom_size, sizeof(u16), GFP_KERNEL);
+ if (!sprom)
+@@ -111,18 +125,13 @@ ssize_t ssb_attr_sprom_store(struct ssb_
+ err = -ERESTARTSYS;
+ if (mutex_lock_interruptible(&bus->sprom_mutex))
+ goto out_kfree;
+- err = ssb_devices_freeze(bus);
+- if (err == -EOPNOTSUPP) {
+- ssb_printk(KERN_ERR PFX "SPROM write: Could not freeze devices. "
+- "No suspend support. Is CONFIG_PM enabled?\n");
+- goto out_unlock;
+- }
++ err = ssb_devices_freeze(bus, &freeze);
+ if (err) {
+ ssb_printk(KERN_ERR PFX "SPROM write: Could not freeze all devices\n");
+ goto out_unlock;
+ }
+ res = sprom_write(bus, sprom);
+- err = ssb_devices_thaw(bus);
++ err = ssb_devices_thaw(&freeze);
+ if (err)
+ ssb_printk(KERN_ERR PFX "SPROM write: Could not thaw all devices\n");
+ out_unlock:
+@@ -167,3 +176,17 @@ const struct ssb_sprom *ssb_get_fallback
+ {
+ return fallback_sprom;
+ }
++
++/* http://bcm-v4.sipsolutions.net/802.11/IsSpromAvailable */
++bool ssb_is_sprom_available(struct ssb_bus *bus)
++{
++ /* status register only exists on chipcomon rev >= 11 and we need check
++ for >= 31 only */
++ /* this routine differs from specs as we do not access SPROM directly
++ on PCMCIA */
++ if (bus->bustype == SSB_BUSTYPE_PCI &&
++ bus->chipco.dev->id.revision >= 31)
++ return bus->chipco.capabilities & SSB_CHIPCO_CAP_SPROM;
++
++ return true;
++}
+--- a/drivers/ssb/ssb_private.h
++++ b/drivers/ssb/ssb_private.h
+@@ -136,19 +136,27 @@ extern const struct ssb_sprom *ssb_get_f
+
+ /* core.c */
+ extern u32 ssb_calc_clock_rate(u32 plltype, u32 n, u32 m);
+-extern int ssb_devices_freeze(struct ssb_bus *bus);
+-extern int ssb_devices_thaw(struct ssb_bus *bus);
+ extern struct ssb_bus *ssb_pci_dev_to_bus(struct pci_dev *pdev);
+ int ssb_for_each_bus_call(unsigned long data,
+ int (*func)(struct ssb_bus *bus, unsigned long data));
+ extern struct ssb_bus *ssb_pcmcia_dev_to_bus(struct pcmcia_device *pdev);
+
++struct ssb_freeze_context {
++ /* Pointer to the bus */
++ struct ssb_bus *bus;
++ /* Boolean list to indicate whether a device is frozen on this bus. */
++ bool device_frozen[SSB_MAX_NR_CORES];
++};
++extern int ssb_devices_freeze(struct ssb_bus *bus, struct ssb_freeze_context *ctx);
++extern int ssb_devices_thaw(struct ssb_freeze_context *ctx);
++
++
+
+ /* b43_pci_bridge.c */
+ #ifdef CONFIG_SSB_B43_PCI_BRIDGE
+ extern int __init b43_pci_ssb_bridge_init(void);
+ extern void __exit b43_pci_ssb_bridge_exit(void);
+-#else /* CONFIG_SSB_B43_PCI_BRIDGR */
++#else /* CONFIG_SSB_B43_PCI_BRIDGE */
+ static inline int b43_pci_ssb_bridge_init(void)
+ {
+ return 0;
+@@ -156,6 +164,6 @@ static inline int b43_pci_ssb_bridge_ini
+ static inline void b43_pci_ssb_bridge_exit(void)
+ {
+ }
+-#endif /* CONFIG_SSB_PCIHOST */
++#endif /* CONFIG_SSB_B43_PCI_BRIDGE */
+
+ #endif /* LINUX_SSB_PRIVATE_H_ */
projects / openwrt.git / blobdiff