diff -urN linux-2.6.19/arch/mips/Kconfig linux-2.6.19.new/arch/mips/Kconfig
--- linux-2.6.19/arch/mips/Kconfig 2006-11-29 22:57:37.000000000 +0100
+++ linux-2.6.19.new/arch/mips/Kconfig 2006-12-16 18:46:31.000000000 +0100
-@@ -12,6 +12,15 @@
+@@ -4,6 +4,10 @@
+ # Horrible source of confusion. Die, die, die ...
+ select EMBEDDED
+
++config CFE
++ bool
++ # Common Firmware Environment
++
+ mainmenu "Linux/MIPS Kernel Configuration"
+
+ menu "Machine selection"
+@@ -12,6 +12,18 @@
prompt "System type"
default SGI_IP22
+config BCM963XX
-+ bool "Support for the Broadcom boards"
++ bool "Support for Broadcom BCM963xx SoC"
+ select SYS_SUPPORTS_32BIT_KERNEL
+ select SYS_SUPPORTS_BIG_ENDIAN
+ select SYS_HAS_CPU_MIPS32_R1
-+ select IRQ_CPU
-+ help
-+ This is a fmaily of boards based on the Broadcom MIPS32
-+
- config MIPS_MTX1
- bool "4G Systems MTX-1 board"
- select DMA_NONCOHERENT
-@@ -766,6 +775,7 @@
-
- endchoice
-
-+source "arch/mips/bcm963xx/Kconfig"
- source "arch/mips/ddb5xxx/Kconfig"
- source "arch/mips/gt64120/ev64120/Kconfig"
- source "arch/mips/jazz/Kconfig"
-diff -urN linux-2.6.19/arch/mips/Makefile linux-2.6.19.new/arch/mips/Makefile
---- linux-2.6.19/arch/mips/Makefile 2006-12-16 17:36:29.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/Makefile 2006-12-16 18:46:31.000000000 +0100
-@@ -158,6 +158,15 @@
- #
-
- #
-+# Broadcom board
-+#
-+core-$(CONFIG_BCM963XX) += arch/mips/bcm963xx/
-+cflags-$(CONFIG_BCM963XX) += -Iinclude/asm-mips/mach-bcm963xx
-+cflags-$(CONFIG_BCM963XX) += -Iarch/mips/bcm963xx/include
-+load-$(CONFIG_BCM963XX) += 0xffffffff80010000
-+
-+
-+#
- # Acer PICA 61, Mips Magnum 4000 and Olivetti M700.
- #
- core-$(CONFIG_MACH_JAZZ) += arch/mips/jazz/
-diff -urN linux-2.6.19/arch/mips/bcm963xx/Kconfig linux-2.6.19.new/arch/mips/bcm963xx/Kconfig
---- linux-2.6.19/arch/mips/bcm963xx/Kconfig 1970-01-01 01:00:00.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/bcm963xx/Kconfig 2006-12-16 18:46:31.000000000 +0100
-@@ -0,0 +1,138 @@
-+# Kernel and Driver configuration for Broadcom Commengine ADSL board
-+choice
-+ prompt "Broadcom Commengine ADSL board"
-+ depends on BCM963XX
-+ default BCM96348
-+ help
-+ Select different Broadcom ADSL board
-+
-+config BCM96338
-+ bool "96338 ADSL board"
-+ select DMA_NONCOHERENT
-+ select HW_HAS_PCI
-+
-+config BCM96345
-+ bool "96345 ADSL board"
-+ select DMA_NONCOHERENT
-+ select HW_HAS_PCI
-+
-+config BCM96348
-+ bool "96348 ADSL board"
-+ select DMA_NONCOHERENT
-+ select HW_HAS_PCI
-+
-+endchoice
-+
-+config BCM_BOARD
-+ bool "Support for Broadcom Board"
-+ depends on BCM96338 || BCM96345 || BCM96348
-+
-+config BCM_SERIAL
-+ bool "Support for Serial Port"
-+ depends on BCM96338 || BCM96345 || BCM96348
-+
-+config BCM_ENET
-+ tristate "Support for Ethernet"
-+ depends on BCM96338 || BCM96345 || BCM96348
-+
-+config BCM_USB
-+ tristate "Support for USB"
-+ depends on BCM96338 || BCM96345 || BCM96348
-+
-+config BCM_WLAN
-+ tristate "Support for Wireless"
-+ depends on BCM96338 || BCM96345 || BCM96348
-+
-+config BCM_PCI
-+ bool "Support for PCI"
-+ depends on BCM96338 || BCM96345 || BCM96348
-+ select PCI
-+
-+config BCM_ATMAPI
-+ tristate "Support for ATM"
-+ depends on BCM96338 || BCM96345 || BCM96348
-+
-+config BCM_ATMTEST
-+ tristate "Support for ATM Diagnostic"
-+ depends on BCM96338 || BCM96345 || BCM96348
-+
-+config BCM_ADSL
-+ tristate "Support for ADSL"
-+ depends on BCM96338 || BCM96345 || BCM96348
-+
-+config BCM_ENDPOINT
-+ tristate "Support for VOICE"
-+ depends on BCM96338 || BCM96345 || BCM96348
-+
-+config BCM_PROCFS
-+ tristate "Support for PROCFS"
-+ depends on BCM96338 || BCM96345 || BCM96348
-+
-+config BCM_VDSL
-+ tristate "Support for VDSL"
-+ depends on BCM96338 || BCM96345 || BCM96348
-+
-+config BCM_SECURITY
-+ tristate "Support for SECURITY"
-+ depends on BCM96338 || BCM96345 || BCM96348
-+
-+config BCM_HPNA
-+ tristate "Support for HPNA"
-+ depends on BCM96338 || BCM96345 || BCM96348
-+
-+config BCM_BOARD_IMPL
-+ int "Implementation index for ADSL Board"
-+ depends on BCM96338 || BCM96345 || BCM96348
-+
-+config BCM_SERIAL_IMPL
-+ int "Implementation index for Serial"
-+ depends on BCM96338 || BCM96345 || BCM96348
-+
-+config BCM_ENET_IMPL
-+ int "Implementation index for Ethernet"
-+ depends on BCM96338 || BCM96345 || BCM96348
-+
-+config BCM_USB_IMPL
-+ int "Implementation index for USB"
-+ depends on BCM96338 || BCM96345 || BCM96348
-+
-+config BCM_WLAN_IMPL
-+ int "Implementation index for WIRELESS"
-+ depends on BCM96338 || BCM96345 || BCM96348
-+
-+config BCM_ATMAPI_IMPL
-+ int "Implementation index for ATM"
-+ depends on BCM96338 || BCM96345 || BCM96348
-+
-+config BCM_ATMTEST_IMPL
-+ int "Implementation index for ATM Diagnostic"
-+ depends on BCM96338 || BCM96345 || BCM96348
-+
-+config BCM_BLAA_IMPL
-+ int "Implementation index for BLAA"
-+ depends on BCM96338 || BCM96345 || BCM96348
-+
-+config BCM_ADSL_IMPL
-+ int "Implementation index for ADSL"
-+ depends on BCM96338 || BCM96345 || BCM96348
-+
-+config BCM_ENDPOINT_IMPL
-+ int "Implementation index for VOICE"
-+ depends on BCM96338 || BCM96345 || BCM96348
-+
-+config BCM_PROCFS_IMPL
-+ int "Implementation index for PROCFS"
-+ depends on BCM96338 || BCM96345 || BCM96348
-+
-+config BCM_VDSL_IMPL
-+ int "Implementation index for VDSL"
-+ depends on BCM96338 || BCM96345 || BCM96348
-+
-+config BCM_SECURITY_IMPL
-+ int "Implementation index for SECURITY"
-+ depends on BCM96338 || BCM96345 || BCM96348
-+
-+config BCM_HPNA_IMPL
-+ int "Implementation index for HPNA"
-+ depends on BCM96338 || BCM96345 || BCM96348
-+
-diff -urN linux-2.6.19/arch/mips/bcm963xx/Makefile linux-2.6.19.new/arch/mips/bcm963xx/Makefile
---- linux-2.6.19/arch/mips/bcm963xx/Makefile 1970-01-01 01:00:00.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/bcm963xx/Makefile 2006-12-16 18:46:31.000000000 +0100
-@@ -0,0 +1,23 @@
-+#
-+# Makefile for generic Broadcom MIPS boards
-+#
-+# Copyright (C) 2004 Broadcom Corporation
-+#
-+obj-y := irq.o prom.o setup.o time.o ser_init.o bcm63xx_led.o board.o boardparms.o int-handler.o
-+
-+SRCBASE := $(TOPDIR)
-+EXTRA_CFLAGS += -I$(SRCBASE)/include
-+#EXTRA_CFLAGS += -I$(INC_ADSLDRV_PATH) -DDBG
-+EXTRA_CFLAGS += -I$(INC_ADSLDRV_PATH)
-+
-+
-+ifeq "$(ADSL)" "ANNEX_B"
-+EXTRA_CFLAGS += -DADSL_ANNEXB
-+endif
-+ifeq "$(ADSL)" "SADSL"
-+EXTRA_CFLAGS += -DADSL_SADSL
-+endif
-+ifeq "$(ADSL)" "ANNEX_C"
-+EXTRA_CFLAGS += -DADSL_ANNEXC
-+endif
-+
-diff -urN linux-2.6.19/arch/mips/bcm963xx/bcm63xx_led.c linux-2.6.19.new/arch/mips/bcm963xx/bcm63xx_led.c
---- linux-2.6.19/arch/mips/bcm963xx/bcm63xx_led.c 1970-01-01 01:00:00.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/bcm963xx/bcm63xx_led.c 2006-12-16 18:46:31.000000000 +0100
-@@ -0,0 +1,582 @@
-+/*
-+<:copyright-gpl
-+ Copyright 2002 Broadcom Corp. All Rights Reserved.
-+
-+ This program is free software; you can distribute it and/or modify it
-+ under the terms of the GNU General Public License (Version 2) as
-+ published by the Free Software Foundation.
-+
-+ This program is distributed in the hope it will be useful, but WITHOUT
-+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-+ for more details.
-+
-+ You should have received a copy of the GNU General Public License along
-+ with this program; if not, write to the Free Software Foundation, Inc.,
-+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-+:>
-+*/
-+/***************************************************************************
-+ * File Name : bcm63xx_led.c
-+ *
-+ * Description:
-+ *
-+ * This file contains bcm963xx board led control API functions.
-+ *
-+ * To use it, do the following
-+ *
-+ * 1). define in the board.c the following led mappping (this is for 6345GW board):
-+ * const LED_MAP_PAIR cLedMapping45GW[] =
-+ * { // led name Initial state physical pin (ledMask)
-+ * {kLedUsb, kLedStateOff, GPIO_LED_PIN_7},
-+ * {kLedAdsl, kLedStateOff, GPIO_LED_PIN_8},
-+ * {kLedPPP, kLedStateOff, GPIO_LED_PIN_9}, // PPP and WanData share PIN_9
-+ * {kLedWanData, kLedStateOff, GPIO_LED_PIN_9},
-+ * {kLedWireless, kLedStateOff, GPIO_LED_PIN_10},
-+ * {kLedEnd, kLedStateOff, 0 } // NOTE: kLedEnd has to be at the end.
-+ *
-+ * 2). };To initialize led API and initial state of the leds, call the following function with the mapping
-+ * pointer from the above struct
-+ *
-+ * boardLedInit((PLED_MAP_PAIR) &cLedMapping45R);
-+ *
-+ * 3). Sample call for kernel mode:
-+ *
-+ * kerSysLedCtrl(kLedAdsl, kLedStateBlinkOnce); // kLedxxx defines in board.h
-+ *
-+ * 4). Sample call for user mode
-+ *
-+ * sysLedCtrl(kLedAdsl, kLedStateBlinkOnce); // kLedxxx defines in board_api.h
-+ *
-+ *
-+ * Created on : 10/28/2002 seanl
-+ *
-+ ***************************************************************************/
-+
-+/* Includes. */
-+#include <linux/init.h>
-+#include <linux/fs.h>
-+#include <linux/capability.h>
-+#include <linux/slab.h>
-+#include <linux/errno.h>
-+#include <linux/module.h>
-+#include <linux/netdevice.h>
-+#include <asm/uaccess.h>
-+
-+#include <bcm_map_part.h>
-+#include <board.h>
-+
-+#define k100ms (HZ / 10) // ~100 ms
-+#define kFastBlinkCount 0 // ~100ms
-+#define kSlowBlinkCount 5 // ~600ms
-+
-+#define MAX_VIRT_LEDS 12
-+
-+// uncomment // for debug led
-+//#define DEBUG_LED
-+
-+// global variables:
-+struct timer_list gLedTimer;
-+int gTimerOn = FALSE;
-+int gLedCount = 0;
-+
-+typedef struct ledinfo
-+{
-+ unsigned short ledMask; // mask for led: ie. giop 10 = 0x0400
-+ unsigned short ledActiveLow; // GPIO bit reset to turn on LED
-+ unsigned short ledMaskFail; // mask for led: ie. giop 10 = 0x0400
-+ unsigned short ledActiveLowFail;// GPIO bit reset to turn on LED
-+ BOARD_LED_STATE ledState; // current led state
-+ BOARD_LED_STATE savedLedState; // used in blink once for restore to the orignal ledState
-+ int blinkCountDown; // if == 0, do blink (toggle). Is assgined value and dec by 1 at each timer.
-+} LED_INFO, *PLED_INFO;
-+
-+static PLED_INFO gLed = NULL;
-+static PLED_INFO gpVirtLeds[MAX_VIRT_LEDS];
-+static HANDLE_LED_FUNC gLedHwFunc[MAX_VIRT_LEDS];
-+static HANDLE_LED_FUNC gLedHwFailFunc[MAX_VIRT_LEDS];
-+
-+#if 0 /* BROKEN */
-+#if defined(CONFIG_BCM96348) || defined(CONFIG_BCM96338)
-+static int gLedOffInBridgeMode = 1;
-+#elif defined(CONFIG_BCM96345)
-+static int gLedOffInBridgeMode = 0;
-+#endif
-+#endif
-+
-+void ledTimerExpire(void);
-+int initLedInfo( PLED_MAP_PAIR pCurMap, PLED_INFO pCurLed );
-+
-+//**************************************************************************************
-+// LED operations
-+//**************************************************************************************
-+
-+// turn led on and set the ledState
-+void ledOn(PLED_INFO pLed)
-+{
-+ if( pLed->ledMask )
-+ {
-+ GPIO->GPIODir |= pLed->ledMask; // turn on the direction bit in case was turned off by some one
-+ if( pLed->ledActiveLow )
-+ GPIO->GPIOio &= ~pLed->ledMask; // turn on the led
-+ else
-+ GPIO->GPIOio |= pLed->ledMask; // turn on the led
-+ pLed->ledState = pLed->savedLedState = kLedStateOn;
-+ }
-+}
-+
-+
-+// turn led off and set the ledState
-+void ledOff(PLED_INFO pLed)
-+{
-+ if( pLed->ledMask )
-+ {
-+ GPIO->GPIODir |= pLed->ledMask; // turn on the direction bit in case was turned off by some one
-+ if( pLed->ledActiveLow )
-+ GPIO->GPIOio |= pLed->ledMask; // turn off the led
-+ else
-+ GPIO->GPIOio &= ~pLed->ledMask; // turn off the led
-+ pLed->ledState = pLed->savedLedState = kLedStateOff;
-+ }
-+}
-+
-+// turn led on and set the ledState
-+void ledOnFail(PLED_INFO pLed)
-+{
-+ if( pLed->ledMaskFail )
-+ {
-+ GPIO->GPIODir |= pLed->ledMaskFail; // turn on the direction bit in case was turned off by some one
-+ if( pLed->ledActiveLowFail )
-+ GPIO->GPIOio &= ~pLed->ledMaskFail;// turn on the led
-+ else
-+ GPIO->GPIOio |= pLed->ledMaskFail; // turn on the led
-+ pLed->ledState = pLed->savedLedState = kLedStateFail;
-+ }
-+}
-+
-+
-+// turn led off and set the ledState
-+void ledOffFail(PLED_INFO pLed)
-+{
-+ if( pLed->ledMaskFail )
-+ {
-+ GPIO->GPIODir |= pLed->ledMaskFail; // turn on the direction bit in case was turned off by some one
-+ if( pLed->ledActiveLowFail )
-+ GPIO->GPIOio |= pLed->ledMaskFail; // turn off the led
-+ else
-+ GPIO->GPIOio &= ~pLed->ledMaskFail;// turn off the led
-+ pLed->ledState = pLed->savedLedState = kLedStateOff;
-+ }
-+}
-+
-+
-+// toggle the led and return the current ledState
-+BOARD_LED_STATE ledToggle(PLED_INFO pLed)
-+{
-+ GPIO->GPIODir |= pLed->ledMask; // turn on the direction bit in case was turned off by some one
-+ if (GPIO->GPIOio & pLed->ledMask)
-+ {
-+ GPIO->GPIOio &= ~(pLed->ledMask);
-+ return( (pLed->ledActiveLow) ? kLedStateOn : kLedStateOff );
-+ }
-+ else
-+ {
-+ GPIO->GPIOio |= pLed->ledMask;
-+ return( (pLed->ledActiveLow) ? kLedStateOff : kLedStateOn );
-+ }
-+}
-+
-+
-+// led timer. Will return if timer is already on
-+void ledTimerStart(void)
-+{
-+ if (gTimerOn)
-+ return;
-+
-+#if defined(DEBUG_LED)
-+ printk("led: add_timer\n");
-+#endif
-+
-+ init_timer(&gLedTimer);
-+ gLedTimer.function = (void*)ledTimerExpire;
-+ gLedTimer.expires = jiffies + k100ms; // timer expires in ~100ms
-+ add_timer (&gLedTimer);
-+ gTimerOn = TRUE;
-+}
-+
-+
-+// led timer expire kicks in about ~100ms and perform the led operation according to the ledState and
-+// restart the timer according to ledState
-+void ledTimerExpire(void)
-+{
-+ int i;
-+ PLED_INFO pCurLed;
-+
-+ gTimerOn = FALSE;
-+
-+ for (i = 0, pCurLed = gLed; i < gLedCount; i++, pCurLed++)
-+ {
-+#if defined(DEBUG_LED)
-+ printk("led[%d]: Mask=0x%04x, State = %d, blcd=%d\n", i, pCurLed->ledMask, pCurLed->ledState, pCurLed->blinkCountDown);
-+#endif
-+ switch (pCurLed->ledState)
-+ {
-+ case kLedStateOn:
-+ case kLedStateOff:
-+ case kLedStateFail:
-+ pCurLed->blinkCountDown = 0; // reset the blink count down
-+ break;
-+
-+ case kLedStateBlinkOnce:
-+ ledToggle(pCurLed);
-+ pCurLed->blinkCountDown = 0; // reset to 0
-+ pCurLed->ledState = pCurLed->savedLedState;
-+ if (pCurLed->ledState == kLedStateSlowBlinkContinues ||
-+ pCurLed->ledState == kLedStateFastBlinkContinues)
-+ ledTimerStart(); // start timer if in blinkContinues stats
-+ break;
-+
-+ case kLedStateSlowBlinkContinues:
-+ if (pCurLed->blinkCountDown-- == 0)
-+ {
-+ pCurLed->blinkCountDown = kSlowBlinkCount;
-+ ledToggle(pCurLed);
-+ }
-+ ledTimerStart();
-+ break;
-+
-+ case kLedStateFastBlinkContinues:
-+ if (pCurLed->blinkCountDown-- == 0)
-+ {
-+ pCurLed->blinkCountDown = kFastBlinkCount;
-+ ledToggle(pCurLed);
-+ }
-+ ledTimerStart();
-+ break;
-+
-+ default:
-+ printk("Invalid state = %d\n", pCurLed->ledState);
-+ }
-+ }
-+}
-+
-+// initialize the gLedCount and allocate and fill gLed struct
-+void __init boardLedInit(PLED_MAP_PAIR cLedMapping)
-+{
-+ PLED_MAP_PAIR p1, p2;
-+ PLED_INFO pCurLed;
-+ int needTimer = FALSE;
-+ int alreadyUsed = 0;
-+
-+#if defined(CONFIG_BCM96348) || defined(CONFIG_BCM96338)
-+ /* Set blink rate for BCM6348/BCM6338 hardware LEDs. */
-+ GPIO->LEDCtrl &= ~LED_INTERVAL_SET_MASK;
-+ GPIO->LEDCtrl |= LED_INTERVAL_SET_80MS;
-+#endif
-+
-+ memset( gpVirtLeds, 0x00, sizeof(gpVirtLeds) );
-+ memset( gLedHwFunc, 0x00, sizeof(gLedHwFunc) );
-+ memset( gLedHwFailFunc, 0x00, sizeof(gLedHwFailFunc) );
-+
-+ gLedCount = 0;
-+
-+ // Check for multiple LED names and multiple LED GPIO pins that share the
-+ // same physical board LED.
-+ for( p1 = cLedMapping; p1->ledName != kLedEnd; p1++ )
-+ {
-+ alreadyUsed = 0;
-+ for( p2 = cLedMapping; p2 != p1; p2++ )
-+ {
-+ if( (p1->ledMask && p1->ledMask == p2->ledMask) ||
-+ (p1->ledMaskFail && p1->ledMaskFail == p2->ledMaskFail) )
-+ {
-+ alreadyUsed = 1;
-+ break;
-+ }
-+ }
-+
-+ if( alreadyUsed == 0 )
-+ gLedCount++;
-+ }
-+
-+ gLed = (PLED_INFO) kmalloc((gLedCount * sizeof(LED_INFO)), GFP_KERNEL);
-+ if( gLed == NULL )
-+ {
-+ printk( "LED memory allocation error.\n" );
-+ return;
-+ }
-+
-+ memset( gLed, 0x00, gLedCount * sizeof(LED_INFO) );
-+
-+ // initial the gLed with unique ledMask and initial state. If more than 1 ledNames share the physical led
-+ // (ledMask) the first defined led's ledInitState will be used.
-+ pCurLed = gLed;
-+ for( p1 = cLedMapping; p1->ledName != kLedEnd; p1++ )
-+ {
-+ if( (int) p1->ledName > MAX_VIRT_LEDS )
-+ continue;
-+
-+ alreadyUsed = 0;
-+ for( p2 = cLedMapping; p2 != p1; p2++ )
-+ {
-+ if( (p1->ledMask && p1->ledMask == p2->ledMask) ||
-+ (p1->ledMaskFail && p1->ledMaskFail == p2->ledMaskFail) )
-+ {
-+ alreadyUsed = 1;
-+ break;
-+ }
-+ }
-+
-+ if( alreadyUsed == 0 )
-+ {
-+ // Initialize the board LED for the first time.
-+ needTimer = initLedInfo( p1, pCurLed );
-+ gpVirtLeds[(int) p1->ledName] = pCurLed;
-+ pCurLed++;
-+ }
-+ else
-+ {
-+ PLED_INFO pLed;
-+ for( pLed = gLed; pLed != pCurLed; pLed++ )
-+ {
-+ // Find the LED_INFO structure that has already been initialized.
-+ if((pLed->ledMask && pLed->ledMask == p1->ledMask) ||
-+ (pLed->ledMaskFail && pLed->ledMaskFail==p1->ledMaskFail))
-+ {
-+ // The board LED has already been initialized but possibly
-+ // not completely initialized.
-+ if( p1->ledMask )
-+ {
-+ pLed->ledMask = p1->ledMask;
-+ pLed->ledActiveLow = p1->ledActiveLow;
-+ }
-+ if( p1->ledMaskFail )
-+ {
-+ pLed->ledMaskFail = p1->ledMaskFail;
-+ pLed->ledActiveLowFail = p1->ledActiveLowFail;
-+ }
-+ gpVirtLeds[(int) p1->ledName] = pLed;
-+ break;
-+ }
-+ }
-+ }
-+ }
-+
-+ if (needTimer)
-+ ledTimerStart();
-+
-+#if defined(DEBUG_LED)
-+ int i;
-+ for (i=0; i < gLedCount; i++)
-+ printk("initLed: led[%d]: mask=0x%04x, state=%d\n", i,(gLed+i)->ledMask, (gLed+i)->ledState);
-+#endif
-+
-+}
-+
-+// Initialize a structure that contains information about a physical board LED
-+// control. The board LED may contain more than one GPIO pin to control a
-+// normal condition (green) or a failure condition (red).
-+int initLedInfo( PLED_MAP_PAIR pCurMap, PLED_INFO pCurLed )
-+{
-+ int needTimer = FALSE;
-+ pCurLed->ledState = pCurLed->savedLedState = pCurMap->ledInitState;
-+ pCurLed->ledMask = pCurMap->ledMask;
-+ pCurLed->ledActiveLow = pCurMap->ledActiveLow;
-+ pCurLed->ledMaskFail = pCurMap->ledMaskFail;
-+ pCurLed->ledActiveLowFail = pCurMap->ledActiveLowFail;
-+
-+ switch (pCurLed->ledState)
-+ {
-+ case kLedStateOn:
-+ pCurLed->blinkCountDown = 0; // reset the blink count down
-+ ledOn(pCurLed);
-+ break;
-+ case kLedStateOff:
-+ pCurLed->blinkCountDown = 0; // reset the blink count down
-+ ledOff(pCurLed);
-+ break;
-+ case kLedStateFail:
-+ pCurLed->blinkCountDown = 0; // reset the blink count down
-+ ledOnFail(pCurLed);
-+ break;
-+ case kLedStateBlinkOnce:
-+ pCurLed->blinkCountDown = 1;
-+ needTimer = TRUE;
-+ break;
-+ case kLedStateSlowBlinkContinues:
-+ pCurLed->blinkCountDown = kSlowBlinkCount;
-+ needTimer = TRUE;
-+ break;
-+ case kLedStateFastBlinkContinues:
-+ pCurLed->blinkCountDown = kFastBlinkCount;
-+ needTimer = TRUE;
-+ break;
-+ default:
-+ printk("Invalid state = %d\n", pCurLed->ledState);
-+ }
-+
-+ return( needTimer );
-+}
-+
-+#if 0 /* BROKEN */
-+// Determines if there is at least one interface in bridge mode. Bridge mode
-+// is determined by the cfm convention of naming bridge interfaces nas17
-+// through nas24.
-+static int isBridgedProtocol(void)
-+{
-+ extern int dev_get(const char *name);
-+ const int firstBridgeId = 17;
-+ const int lastBridgeId = 24;
-+ int i;
-+ int ret = FALSE;
-+ char name[16];
-+
-+ for( i = firstBridgeId; i <= lastBridgeId; i++ )
-+ {
-+ sprintf( name, "nas%d", i );
-+
-+ if( dev_get(name) )
-+ {
-+ ret = TRUE;
-+ break;
-+ }
-+ }
-+
-+ return(ret);
-+}
-+#endif
-+
-+// led ctrl. Maps the ledName to the corresponding ledInfoPtr and perform the led operation
-+void boardLedCtrl(BOARD_LED_NAME ledName, BOARD_LED_STATE ledState)
-+{
-+ PLED_INFO ledInfoPtr;
-+
-+ // do the mapping from virtual to physical led
-+ if( (int) ledName < MAX_VIRT_LEDS )
-+ ledInfoPtr = gpVirtLeds[(int) ledName];
-+ else
-+ ledInfoPtr = NULL;
-+
-+ if (ledInfoPtr == NULL)
-+ return;
-+
-+ if( ledState != kLedStateFail && gLedHwFunc[(int) ledName] )
-+ {
-+ (*gLedHwFunc[(int) ledName]) (ledName, ledState);
-+ ledOffFail(ledInfoPtr);
-+ return;
-+ }
-+ else
-+ if( ledState == kLedStateFail && gLedHwFailFunc[(int) ledName] )
-+ {
-+ (*gLedHwFailFunc[(int) ledName]) (ledName, ledState);
-+ ledOff(ledInfoPtr);
-+ return;
-+ }
-+
-+#if 0 /* BROKEN */
-+ // Do not blink the WAN Data LED if at least one interface is in bridge mode.
-+ if(gLedOffInBridgeMode == 1 && (ledName == kLedWanData || ledName == kLedPPP))
-+ {
-+ static int BridgedProtocol = -1;
-+
-+ if( BridgedProtocol == -1 )
-+ BridgedProtocol = isBridgedProtocol();
-+
-+ if( BridgedProtocol == TRUE )
-+ return;
-+ }
-+#endif
-+
-+ // If the state is kLedStateFail and there is not a failure LED defined
-+ // in the board parameters, change the state to kLedStateFastBlinkContinues.
-+ if( ledState == kLedStateFail && ledInfoPtr->ledMaskFail == 0 )
-+ ledState = kLedStateFastBlinkContinues;
-+
-+ switch (ledState)
-+ {
-+ case kLedStateOn:
-+ // First, turn off the complimentary (failure) LED GPIO.
-+ if( ledInfoPtr->ledMaskFail )
-+ ledOffFail(ledInfoPtr);
-+ else
-+ if( gLedHwFailFunc[(int) ledName] )
-+ (*gLedHwFailFunc[(int) ledName]) (ledName, kLedStateOff);
-+
-+ // Next, turn on the specified LED GPIO.
-+ ledOn(ledInfoPtr);
-+ break;
-+
-+ case kLedStateOff:
-+ // First, turn off the complimentary (failure) LED GPIO.
-+ if( ledInfoPtr->ledMaskFail )
-+ ledOffFail(ledInfoPtr);
-+ else
-+ if( gLedHwFailFunc[(int) ledName] )
-+ (*gLedHwFailFunc[(int) ledName]) (ledName, kLedStateOff);
-+
-+ // Next, turn off the specified LED GPIO.
-+ ledOff(ledInfoPtr);
-+ break;
-+
-+ case kLedStateFail:
-+ // First, turn off the complimentary (normal) LED GPIO.
-+ if( ledInfoPtr->ledMask )
-+ ledOff(ledInfoPtr);
-+ else
-+ if( gLedHwFunc[(int) ledName] )
-+ (*gLedHwFunc[(int) ledName]) (ledName, kLedStateOff);
-+
-+ // Next, turn on (red) the specified LED GPIO.
-+ ledOnFail(ledInfoPtr);
-+ break;
-+
-+ case kLedStateBlinkOnce:
-+ // skip blinkOnce if it is already in Slow/Fast blink continues state
-+ if (ledInfoPtr->savedLedState == kLedStateSlowBlinkContinues ||
-+ ledInfoPtr->savedLedState == kLedStateFastBlinkContinues)
-+ ;
-+ else
-+ {
-+ if (ledInfoPtr->blinkCountDown == 0) // skip the call if it is 1
-+ {
-+ ledToggle(ledInfoPtr);
-+ ledInfoPtr->blinkCountDown = 1; // it will be reset to 0 when timer expires
-+ ledInfoPtr->ledState = kLedStateBlinkOnce;
-+ ledTimerStart();
-+ }
-+ }
-+ break;
-+
-+ case kLedStateSlowBlinkContinues:
-+ ledInfoPtr->blinkCountDown = kSlowBlinkCount;
-+ ledInfoPtr->ledState = kLedStateSlowBlinkContinues;
-+ ledInfoPtr->savedLedState = kLedStateSlowBlinkContinues;
-+ ledTimerStart();
-+ break;
-+
-+ case kLedStateFastBlinkContinues:
-+ ledInfoPtr->blinkCountDown = kFastBlinkCount;
-+ ledInfoPtr->ledState = kLedStateFastBlinkContinues;
-+ ledInfoPtr->savedLedState = kLedStateFastBlinkContinues;
-+ ledTimerStart();
-+ break;
-+
-+ default:
-+ printk("Invalid led state\n");
-+ }
-+}
-+
-+// This function is called for an LED that is controlled by hardware.
-+void kerSysLedRegisterHwHandler( BOARD_LED_NAME ledName,
-+ HANDLE_LED_FUNC ledHwFunc, int ledFailType )
-+{
-+ if( (int) ledName < MAX_VIRT_LEDS )
-+ {
-+ if( ledFailType == 1 )
-+ gLedHwFailFunc[(int) ledName] = ledHwFunc;
-+ else
-+ gLedHwFunc[(int) ledName] = ledHwFunc;
-+ }
-+}
-+
-diff -urN linux-2.6.19/arch/mips/bcm963xx/board.c linux-2.6.19.new/arch/mips/bcm963xx/board.c
---- linux-2.6.19/arch/mips/bcm963xx/board.c 1970-01-01 01:00:00.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/bcm963xx/board.c 2006-12-16 18:46:31.000000000 +0100
-@@ -0,0 +1,559 @@
-+/*
-+<:copyright-gpl
-+ Copyright 2002 Broadcom Corp. All Rights Reserved.
-+
-+ This program is free software; you can distribute it and/or modify it
-+ under the terms of the GNU General Public License (Version 2) as
-+ published by the Free Software Foundation.
-+
-+ This program is distributed in the hope it will be useful, but WITHOUT
-+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-+ for more details.
-+
-+ You should have received a copy of the GNU General Public License along
-+ with this program; if not, write to the Free Software Foundation, Inc.,
-+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-+:>
-+*/
-+
-+/* Includes. */
-+#include <linux/version.h>
-+#include <linux/init.h>
-+#include <linux/fs.h>
-+#include <linux/interrupt.h>
-+#include <linux/capability.h>
-+#include <linux/slab.h>
-+#include <linux/errno.h>
-+#include <linux/module.h>
-+#include <linux/pagemap.h>
-+#include <asm/uaccess.h>
-+#include <linux/wait.h>
-+#include <linux/poll.h>
-+#include <linux/sched.h>
-+#include <linux/list.h>
-+#include <linux/if.h>
-+#include <linux/spinlock.h>
-+
-+#include <bcm_map_part.h>
-+#include <board.h>
-+#include <bcmTag.h>
-+#include "boardparms.h"
-+#include "bcm_intr.h"
-+#include "board.h"
-+#include "bcm_map_part.h"
-+
-+static DEFINE_SPINLOCK(board_lock);
-+
-+/* Typedefs. */
-+#if defined (NON_CONSECUTIVE_MAC)
-+// used to be the last octet. Now changed to the first 5 bits of the the forth octet
-+// to reduced the duplicated MAC addresses.
-+#define CHANGED_OCTET 3
-+#define SHIFT_BITS 3
-+#else
-+#define CHANGED_OCTET 1
-+#define SHIFT_BITS 0
-+#endif
-+
-+typedef struct
-+{
-+ unsigned long ulId;
-+ char chInUse;
-+ char chReserved[3];
-+} MAC_ADDR_INFO, *PMAC_ADDR_INFO;
-+
-+typedef struct
-+{
-+ unsigned long ulSdramSize;
-+ unsigned long ulPsiSize;
-+ unsigned long ulNumMacAddrs;
-+ unsigned long ucaBaseMacAddr[NVRAM_MAC_ADDRESS_LEN];
-+ MAC_ADDR_INFO MacAddrs[1];
-+} NVRAM_INFO, *PNVRAM_INFO;
-+
-+typedef struct
-+{
-+ unsigned long eventmask;
-+} BOARD_IOC, *PBOARD_IOC;
-+
-+
-+/*Dyinggasp callback*/
-+typedef void (*cb_dgasp_t)(void *arg);
-+typedef struct _CB_DGASP__LIST
-+{
-+ struct list_head list;
-+ char name[IFNAMSIZ];
-+ cb_dgasp_t cb_dgasp_fn;
-+ void *context;
-+}CB_DGASP_LIST , *PCB_DGASP_LIST;
-+
-+
-+static LED_MAP_PAIR LedMapping[] =
-+{ // led name Initial state physical pin (ledMask)
-+ {kLedEnd, kLedStateOff, 0, 0, 0, 0},
-+ {kLedEnd, kLedStateOff, 0, 0, 0, 0},
-+ {kLedEnd, kLedStateOff, 0, 0, 0, 0},
-+ {kLedEnd, kLedStateOff, 0, 0, 0, 0},
-+ {kLedEnd, kLedStateOff, 0, 0, 0, 0},
-+ {kLedEnd, kLedStateOff, 0, 0, 0, 0},
-+ {kLedEnd, kLedStateOff, 0, 0, 0, 0},
-+ {kLedEnd, kLedStateOff, 0, 0, 0, 0},
-+ {kLedEnd, kLedStateOff, 0, 0, 0, 0} // NOTE: kLedEnd has to be at the end.
-+};
-+
-+/* Externs. */
-+extern struct file fastcall *fget_light(unsigned int fd, int *fput_needed);
-+extern unsigned int nr_free_pages (void);
-+extern const char *get_system_type(void);
-+extern void kerSysFlashInit(void);
-+extern unsigned long get_nvram_start_addr(void);
-+extern unsigned long get_scratch_pad_start_addr(void);
-+extern unsigned long getMemorySize(void);
-+extern void __init boardLedInit(PLED_MAP_PAIR);
-+extern void boardLedCtrl(BOARD_LED_NAME, BOARD_LED_STATE);
-+extern void kerSysLedRegisterHandler( BOARD_LED_NAME ledName,
-+ HANDLE_LED_FUNC ledHwFunc, int ledFailType );
-+
-+/* Prototypes. */
-+void __init InitNvramInfo( void );
-+
-+/* DyingGasp function prototype */
-+static void __init kerSysDyingGaspMapIntr(void);
-+static irqreturn_t kerSysDyingGaspIsr(int irq, void * dev_id);
-+static void __init kerSysInitDyingGaspHandler( void );
-+static void __exit kerSysDeinitDyingGaspHandler( void );
-+/* -DyingGasp function prototype - */
-+
-+static PNVRAM_INFO g_pNvramInfo = NULL;
-+static int g_ledInitialized = 0;
-+static CB_DGASP_LIST *g_cb_dgasp_list_head = NULL;
-+
-+static int g_wakeup_monitor = 0;
-+static struct file *g_monitor_file = NULL;
-+static struct task_struct *g_monitor_task = NULL;
-+static unsigned int (*g_orig_fop_poll)
-+ (struct file *, struct poll_table_struct *) = NULL;
-+
-+void kerSysMipsSoftReset(void)
-+{
-+ if (PERF->RevID == 0x634800A1) {
-+ typedef void (*FNPTR) (void);
-+ FNPTR bootaddr = (FNPTR) FLASH_BASE;
-+ int i;
-+
-+ /* Disable interrupts. */
-+ //cli();
-+ spin_lock_irq(&board_lock);
-+
-+ /* Reset all blocks. */
-+ PERF->BlockSoftReset &= ~BSR_ALL_BLOCKS;
-+ for( i = 0; i < 1000000; i++ )
-+ ;
-+ PERF->BlockSoftReset |= BSR_ALL_BLOCKS;
-+ /* Jump to the power on address. */
-+ (*bootaddr) ();
-+ }
-+ else
-+ PERF->pll_control |= SOFT_RESET; // soft reset mips
-+}
-+
-+
-+int kerSysGetMacAddress( unsigned char *pucaMacAddr, unsigned long ulId )
-+{
-+ int nRet = 0;
-+ PMAC_ADDR_INFO pMai = NULL;
-+ PMAC_ADDR_INFO pMaiFreeNoId = NULL;
-+ PMAC_ADDR_INFO pMaiFreeId = NULL;
-+ unsigned long i = 0, ulIdxNoId = 0, ulIdxId = 0, shiftedIdx = 0;
-+
-+ /* CMO -- Fix le problème avec les adresses mac que l'on n'arrive pas
-+ * * à relire plusieurs fois */
-+ /* inv_xde */
-+#if 0
-+ if (boot_loader_type == BOOT_CFE)
-+ memcpy( pucaMacAddr, g_pNvramInfo->ucaBaseMacAddr,
-+ NVRAM_MAC_ADDRESS_LEN );
-+ else {
-+#endif
-+ pucaMacAddr[0] = 0x00;
-+ pucaMacAddr[1] = 0x07;
-+ pucaMacAddr[2] = 0x3A;
-+ pucaMacAddr[3] = 0xFF;
-+ pucaMacAddr[4] = 0xFF;
-+ pucaMacAddr[5] = 0xFF;
-+#if 0
-+ }
-+#endif
-+
-+ return nRet;
-+} /* kerSysGetMacAddr */
-+
-+int kerSysReleaseMacAddress( unsigned char *pucaMacAddr )
-+{
-+ int nRet = -EINVAL;
-+ unsigned long ulIdx = 0;
-+ int idx = (pucaMacAddr[NVRAM_MAC_ADDRESS_LEN - CHANGED_OCTET] -
-+ g_pNvramInfo->ucaBaseMacAddr[NVRAM_MAC_ADDRESS_LEN - CHANGED_OCTET]);
-+
-+ // if overflow 255 (negitive), add 256 to have the correct index
-+ if (idx < 0)
-+ idx += 256;
-+ ulIdx = (unsigned long) (idx >> SHIFT_BITS);
-+
-+ if( ulIdx < g_pNvramInfo->ulNumMacAddrs )
-+ {
-+ PMAC_ADDR_INFO pMai = &g_pNvramInfo->MacAddrs[ulIdx];
-+ if( pMai->chInUse == 1 )
-+ {
-+ pMai->chInUse = 0;
-+ nRet = 0;
-+ }
-+ }
-+
-+ return( nRet );
-+} /* kerSysReleaseMacAddr */
-+
-+int kerSysGetSdramSize( void )
-+{
-+ if (boot_loader_type == BOOT_CFE) {
-+ return( (int) g_pNvramInfo->ulSdramSize );
-+ }
-+ else {
-+ printk("kerSysGetSdramSize : 0x%08X\n", (int)getMemorySize() + 0x00040000);
-+ return((int)getMemorySize() + 0x00040000);
-+ }
-+} /* kerSysGetSdramSize */
-+
-+
-+void kerSysLedCtrl(BOARD_LED_NAME ledName, BOARD_LED_STATE ledState)
-+{
-+ if (g_ledInitialized)
-+ boardLedCtrl(ledName, ledState);
-+}
-+
-+unsigned int kerSysMonitorPollHook( struct file *f, struct poll_table_struct *t)
-+{
-+ int mask = (*g_orig_fop_poll) (f, t);
-+
-+ if( g_wakeup_monitor == 1 && g_monitor_file == f )
-+ {
-+ /* If g_wakeup_monitor is non-0, the user mode application needs to
-+ * return from a blocking select function. Return POLLPRI which will
-+ * cause the select to return with the exception descriptor set.
-+ */
-+ mask |= POLLPRI;
-+ g_wakeup_monitor = 0;
-+ }
-+
-+ return( mask );
-+}
-+
-+/* Put the user mode application that monitors link state on a run queue. */
-+void kerSysWakeupMonitorTask( void )
-+{
-+ g_wakeup_monitor = 1;
-+ if( g_monitor_task )
-+ wake_up_process( g_monitor_task );
-+}
-+
-+//<<JUNHON, 2004/09/15, get reset button status , tim hou , 05/04/12
-+int kerSysGetResetHold(void)
-+{
-+ unsigned short gpio;
-+
-+ if( BpGetPressAndHoldResetGpio( &gpio ) == BP_SUCCESS )
-+ {
-+ unsigned long gpio_mask = GPIO_NUM_TO_MASK(gpio);
-+ volatile unsigned long *gpio_reg = &GPIO->GPIOio;
-+
-+ if( (gpio & ~BP_ACTIVE_MASK) >= 32 )
-+ {
-+ gpio_mask = GPIO_NUM_TO_MASK_HIGH(gpio);
-+ gpio_reg = &GPIO->GPIOio_high;
-+ }
-+ //printk("gpio=%04x,gpio_mask=%04x,gpio_reg=%04x\n",gpio,gpio_mask,*gpio_reg);
-+ if(*gpio_reg & gpio_mask) //press down
-+ return RESET_BUTTON_UP;
-+ }
-+ return RESET_BUTTON_PRESSDOWN;
-+}
-+//<<JUNHON, 2004/09/15
-+
-+/***************************************************************************
-+ * Dying gasp ISR and functions.
-+ ***************************************************************************/
-+#define KERSYS_DBG printk
-+
-+#if defined(CONFIG_BCM96345)
-+#define CYCLE_PER_US 70
-+#elif defined(CONFIG_BCM96348) || defined(CONFIG_BCM96338)
-+/* The BCM6348 cycles per microsecond is really variable since the BCM6348
-+ * MIPS speed can vary depending on the PLL settings. However, an appoximate
-+ * value of 120 will still work OK for the test being done.
-+ */
-+#define CYCLE_PER_US 120
-+#endif
-+#define DG_GLITCH_TO (100*CYCLE_PER_US)
-+
-+static void __init kerSysDyingGaspMapIntr()
-+{
-+ unsigned long ulIntr;
-+
-+#if defined(CONFIG_BCM96348) || defined(_BCM96348_) || defined(CONFIG_BCM96338) || defined(_BCM96338_)
-+ if( BpGetAdslDyingGaspExtIntr( &ulIntr ) == BP_SUCCESS ) {
-+ BcmHalMapInterrupt((FN_HANDLER)kerSysDyingGaspIsr, 0, INTERRUPT_ID_DG);
-+ BcmHalInterruptEnable( INTERRUPT_ID_DG );
-+ }
-+#elif defined(CONFIG_BCM96345) || defined(_BCM96345_)
-+ if( BpGetAdslDyingGaspExtIntr( &ulIntr ) == BP_SUCCESS ) {
-+ ulIntr += INTERRUPT_ID_EXTERNAL_0;
-+ BcmHalMapInterrupt((FN_HANDLER)kerSysDyingGaspIsr, 0, ulIntr);
-+ BcmHalInterruptEnable( ulIntr );
-+ }
-+#endif
-+
-+}
-+
-+void kerSysSetWdTimer(ulong timeUs)
-+{
-+ TIMER->WatchDogDefCount = timeUs * (FPERIPH/1000000);
-+ TIMER->WatchDogCtl = 0xFF00;
-+ TIMER->WatchDogCtl = 0x00FF;
-+}
-+
-+ulong kerSysGetCycleCount(void)
-+{
-+ ulong cnt;
-+#ifdef _WIN32_WCE
-+ cnt = 0;
-+#else
-+ __asm volatile("mfc0 %0, $9":"=d"(cnt));
-+#endif
-+ return(cnt);
-+}
-+
-+static Bool kerSysDyingGaspCheckPowerLoss(void)
-+{
-+ ulong clk0;
-+ ulong ulIntr;
-+
-+ ulIntr = 0;
-+ clk0 = kerSysGetCycleCount();
-+
-+ UART->Data = 'D';
-+ UART->Data = '%';
-+ UART->Data = 'G';
-+
-+#if defined(CONFIG_BCM96345)
-+ BpGetAdslDyingGaspExtIntr( &ulIntr );
-+
-+ do {
-+ ulong clk1;
-+
-+ clk1 = kerSysGetCycleCount(); /* time cleared */
-+ /* wait a little to get new reading */
-+ while ((kerSysGetCycleCount()-clk1) < CYCLE_PER_US*2)
-+ ;
-+ } while ((0 == (PERF->ExtIrqCfg & (1 << (ulIntr + EI_STATUS_SHFT)))) && ((kerSysGetCycleCount() - clk0) < DG_GLITCH_TO));
-+
-+ if (PERF->ExtIrqCfg & (1 << (ulIntr + EI_STATUS_SHFT))) { /* power glitch */
-+ BcmHalInterruptEnable( ulIntr + INTERRUPT_ID_EXTERNAL_0);
-+ KERSYS_DBG(" - Power glitch detected. Duration: %ld us\n", (kerSysGetCycleCount() - clk0)/CYCLE_PER_US);
-+ return 0;
-+ }
-+#elif (defined(CONFIG_BCM96348) || defined(CONFIG_BCM96338)) && !defined(VXWORKS)
-+ do {
-+ ulong clk1;
-+
-+ clk1 = kerSysGetCycleCount(); /* time cleared */
-+ /* wait a little to get new reading */
-+ while ((kerSysGetCycleCount()-clk1) < CYCLE_PER_US*2)
-+ ;
-+ } while ((PERF->IrqStatus & (1 << (INTERRUPT_ID_DG - INTERNAL_ISR_TABLE_OFFSET))) && ((kerSysGetCycleCount() - clk0) < DG_GLITCH_TO));
-+
-+ if (!(PERF->IrqStatus & (1 << (INTERRUPT_ID_DG - INTERNAL_ISR_TABLE_OFFSET)))) {
-+ BcmHalInterruptEnable( INTERRUPT_ID_DG );
-+ KERSYS_DBG(" - Power glitch detected. Duration: %ld us\n", (kerSysGetCycleCount() - clk0)/CYCLE_PER_US);
-+ return 0;
-+ }
-+#endif
-+ return 1;
-+}
-+
-+static void kerSysDyingGaspShutdown( void )
-+{
-+ kerSysSetWdTimer(1000000);
-+#if defined(CONFIG_BCM96345)
-+ PERF->blkEnables &= ~(EMAC_CLK_EN | USB_CLK_EN | CPU_CLK_EN);
-+#elif defined(CONFIG_BCM96348)
-+ PERF->blkEnables &= ~(EMAC_CLK_EN | USBS_CLK_EN | USBH_CLK_EN | SAR_CLK_EN);
-+#endif
-+}
-+
-+#if (LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,0))
-+static irqreturn_t kerSysDyingGaspIsr(int irq, void * dev_id)
-+#else
-+static unsigned int kerSysDyingGaspIsr(void)
-+#endif
-+{
-+ struct list_head *pos;
-+ CB_DGASP_LIST *tmp, *dsl = NULL;
-+
-+ if (kerSysDyingGaspCheckPowerLoss()) {
-+
-+ /* first to turn off everything other than dsl */
-+ list_for_each(pos, &g_cb_dgasp_list_head->list) {
-+ tmp = list_entry(pos, CB_DGASP_LIST, list);
-+ if(strncmp(tmp->name, "dsl", 3)) {
-+ (tmp->cb_dgasp_fn)(tmp->context);
-+ }else {
-+ dsl = tmp;
-+ }
-+ }
-+
-+ /* now send dgasp */
-+ if(dsl)
-+ (dsl->cb_dgasp_fn)(dsl->context);
-+
-+ /* reset and shutdown system */
-+ kerSysDyingGaspShutdown();
-+ }
-+#if (LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,0))
-+return( IRQ_HANDLED );
-+#else
-+ return( 1 );
-+#endif
-+}
-+
-+static void __init kerSysInitDyingGaspHandler( void )
-+{
-+ CB_DGASP_LIST *new_node;
-+
-+ if( g_cb_dgasp_list_head != NULL) {
-+ printk("Error: kerSysInitDyingGaspHandler: list head is not null\n");
-+ return;
-+ }
-+ new_node= (CB_DGASP_LIST *)kmalloc(sizeof(CB_DGASP_LIST), GFP_KERNEL);
-+ memset(new_node, 0x00, sizeof(CB_DGASP_LIST));
-+ INIT_LIST_HEAD(&new_node->list);
-+ g_cb_dgasp_list_head = new_node;
-+
-+} /* kerSysInitDyingGaspHandler */
-+
-+static void __exit kerSysDeinitDyingGaspHandler( void )
-+{
-+ struct list_head *pos;
-+ CB_DGASP_LIST *tmp;
-+
-+ if(g_cb_dgasp_list_head == NULL)
-+ return;
-+
-+ list_for_each(pos, &g_cb_dgasp_list_head->list) {
-+ tmp = list_entry(pos, CB_DGASP_LIST, list);
-+ list_del(pos);
-+ kfree(tmp);
-+ }
-+
-+ kfree(g_cb_dgasp_list_head);
-+ g_cb_dgasp_list_head = NULL;
-+
-+} /* kerSysDeinitDyingGaspHandler */
-+
-+void kerSysRegisterDyingGaspHandler(char *devname, void *cbfn, void *context)
-+{
-+ CB_DGASP_LIST *new_node;
-+
-+ if( g_cb_dgasp_list_head == NULL) {
-+ printk("Error: kerSysRegisterDyingGaspHandler: list head is null\n");
-+ return;
-+ }
-+
-+ if( devname == NULL || cbfn == NULL ) {
-+ printk("Error: kerSysRegisterDyingGaspHandler: register info not enough (%s,%x,%x)\n", devname, (unsigned int)cbfn, (unsigned int)context);
-+ return;
-+ }
-+
-+ new_node= (CB_DGASP_LIST *)kmalloc(sizeof(CB_DGASP_LIST), GFP_KERNEL);
-+ memset(new_node, 0x00, sizeof(CB_DGASP_LIST));
-+ INIT_LIST_HEAD(&new_node->list);
-+ strncpy(new_node->name, devname, IFNAMSIZ);
-+ new_node->cb_dgasp_fn = (cb_dgasp_t)cbfn;
-+ new_node->context = context;
-+ list_add(&new_node->list, &g_cb_dgasp_list_head->list);
-+
-+ printk("dgasp: kerSysRegisterDyingGaspHandler: %s registered \n", devname);
-+
-+} /* kerSysRegisterDyingGaspHandler */
-+
-+void kerSysDeregisterDyingGaspHandler(char *devname)
-+{
-+ struct list_head *pos;
-+ CB_DGASP_LIST *tmp;
-+
-+ if(g_cb_dgasp_list_head == NULL) {
-+ printk("Error: kerSysDeregisterDyingGaspHandler: list head is null\n");
-+ return;
-+ }
-+
-+ if(devname == NULL) {
-+ printk("Error: kerSysDeregisterDyingGaspHandler: devname is null\n");
-+ return;
-+ }
-+
-+ printk("kerSysDeregisterDyingGaspHandler: %s is deregistering\n", devname);
-+
-+ list_for_each(pos, &g_cb_dgasp_list_head->list) {
-+ tmp = list_entry(pos, CB_DGASP_LIST, list);
-+ if(!strcmp(tmp->name, devname)) {
-+ list_del(pos);
-+ kfree(tmp);
-+ printk("kerSysDeregisterDyingGaspHandler: %s is deregistered\n", devname);
-+ return;
-+ }
-+ }
-+ printk("kerSysDeregisterDyingGaspHandler: %s not (de)registered\n", devname);
-+
-+} /* kerSysDeregisterDyingGaspHandler */
-+
-+//EXPORT_SYMBOL(kerSysNvRamGet);
-+EXPORT_SYMBOL(kerSysGetMacAddress);
-+EXPORT_SYMBOL(kerSysReleaseMacAddress);
-+EXPORT_SYMBOL(kerSysGetSdramSize);
-+EXPORT_SYMBOL(kerSysLedCtrl);
-+EXPORT_SYMBOL(kerSysGetResetHold);
-+EXPORT_SYMBOL(kerSysLedRegisterHwHandler);
-+EXPORT_SYMBOL(BpGetBoardIds);
-+EXPORT_SYMBOL(BpGetSdramSize);
-+EXPORT_SYMBOL(BpGetPsiSize);
-+EXPORT_SYMBOL(BpGetEthernetMacInfo);
-+EXPORT_SYMBOL(BpGetRj11InnerOuterPairGpios);
-+EXPORT_SYMBOL(BpGetPressAndHoldResetGpio);
-+EXPORT_SYMBOL(BpGetVoipResetGpio);
-+EXPORT_SYMBOL(BpGetVoipIntrGpio);
-+EXPORT_SYMBOL(BpGetPcmciaResetGpio);
-+EXPORT_SYMBOL(BpGetRtsCtsUartGpios);
-+EXPORT_SYMBOL(BpGetAdslLedGpio);
-+EXPORT_SYMBOL(BpGetAdslFailLedGpio);
-+EXPORT_SYMBOL(BpGetWirelessLedGpio);
-+EXPORT_SYMBOL(BpGetUsbLedGpio);
-+EXPORT_SYMBOL(BpGetHpnaLedGpio);
-+EXPORT_SYMBOL(BpGetWanDataLedGpio);
-+EXPORT_SYMBOL(BpGetPppLedGpio);
-+EXPORT_SYMBOL(BpGetPppFailLedGpio);
-+EXPORT_SYMBOL(BpGetVoipLedGpio);
-+EXPORT_SYMBOL(BpGetWirelessExtIntr);
-+EXPORT_SYMBOL(BpGetAdslDyingGaspExtIntr);
-+EXPORT_SYMBOL(BpGetVoipExtIntr);
-+EXPORT_SYMBOL(BpGetHpnaExtIntr);
-+EXPORT_SYMBOL(BpGetHpnaChipSelect);
-+EXPORT_SYMBOL(BpGetVoipChipSelect);
-+EXPORT_SYMBOL(BpGetWirelessSesBtnGpio);
-+EXPORT_SYMBOL(BpGetWirelessSesExtIntr);
-+EXPORT_SYMBOL(BpGetWirelessSesLedGpio);
-+EXPORT_SYMBOL(kerSysRegisterDyingGaspHandler);
-+EXPORT_SYMBOL(kerSysDeregisterDyingGaspHandler);
-+EXPORT_SYMBOL(kerSysGetCycleCount);
-+EXPORT_SYMBOL(kerSysSetWdTimer);
-+EXPORT_SYMBOL(kerSysWakeupMonitorTask);
-+
-diff -urN linux-2.6.19/arch/mips/bcm963xx/boardparms.c linux-2.6.19.new/arch/mips/bcm963xx/boardparms.c
---- linux-2.6.19/arch/mips/bcm963xx/boardparms.c 1970-01-01 01:00:00.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/bcm963xx/boardparms.c 2006-12-16 18:46:31.000000000 +0100
-@@ -0,0 +1,2391 @@
-+/*
-+<:copyright-gpl
-+
-+ Copyright 2003 Broadcom Corp. All Rights Reserved.
-+
-+ This program is free software; you can distribute it and/or modify it
-+ under the terms of the GNU General Public License (Version 2) as
-+ published by the Free Software Foundation.
-+
-+ This program is distributed in the hope it will be useful, but WITHOUT
-+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-+ for more details.
-+
-+ You should have received a copy of the GNU General Public License along
-+ with this program; if not, write to the Free Software Foundation, Inc.,
-+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-+
-+:>
-+*/
-+/**************************************************************************
-+ * File Name : boardparms.c
-+ *
-+ * Description: This file contains the implementation for the BCM63xx board
-+ * parameter access functions.
-+ *
-+ * Updates : 07/14/2003 Created.
-+ ***************************************************************************/
-+
-+/* Includes. */
-+#include "boardparms.h"
-+
-+/* Defines. */
-+
-+/* Default psi size in K bytes */
-+#define BP_PSI_DEFAULT_SIZE 24
-+
-+/* Typedefs */
-+typedef struct boardparameters
-+{
-+ char szBoardId[BP_BOARD_ID_LEN]; /* board id string */
-+ ETHERNET_MAC_INFO EnetMacInfos[BP_MAX_ENET_MACS];
-+ VOIP_DSP_INFO VoIPDspInfo[BP_MAX_VOIP_DSP];
-+ unsigned short usSdramSize; /* SDRAM size and type */
-+ unsigned short usPsiSize; /* persistent storage in K bytes */
-+ unsigned short usGpioRj11InnerPair; /* GPIO pin or not defined */
-+ unsigned short usGpioRj11OuterPair; /* GPIO pin or not defined */
-+ unsigned short usGpioPressAndHoldReset; /* GPIO pin or not defined */
-+ unsigned short usGpioPcmciaReset; /* GPIO pin or not defined */
-+ unsigned short usGpioUartRts; /* GPIO pin or not defined */
-+ unsigned short usGpioUartCts; /* GPIO pin or not defined */
-+ unsigned short usGpioLedAdsl; /* GPIO pin or not defined */
-+ unsigned short usGpioLedAdslFail; /* GPIO pin or not defined */
-+ unsigned short usGpioLedWireless; /* GPIO pin or not defined */
-+ unsigned short usGpioLedUsb; /* GPIO pin or not defined */
-+ unsigned short usGpioLedHpna; /* GPIO pin or not defined */
-+ unsigned short usGpioLedWanData; /* GPIO pin or not defined */
-+ unsigned short usGpioLedPpp; /* GPIO pin or not defined */
-+ unsigned short usGpioLedPppFail; /* GPIO pin or not defined */
-+ unsigned short usGpioLedBlPowerOn; /* GPIO pin or not defined */
-+ unsigned short usGpioLedBlAlarm; /* GPIO pin or not defined */
-+ unsigned short usGpioLedBlResetCfg; /* GPIO pin or not defined */
-+ unsigned short usGpioLedBlStop; /* GPIO pin or not defined */
-+ unsigned short usExtIntrWireless; /* ext intr or not defined */
-+ unsigned short usExtIntrAdslDyingGasp; /* ext intr or not defined */
-+ unsigned short usExtIntrHpna; /* ext intr or not defined */
-+ unsigned short usCsHpna; /* chip select not defined */
-+ unsigned short usAntInUseWireless; /* antenna in use or not defined */
-+ unsigned short usGpioSesBtnWireless; /* GPIO pin or not defined */
-+ unsigned short usExtIntrSesBtnWireless; /* ext intr or not defined */
-+ unsigned short usGpioLedSesWireless; /* GPIO pin or not defined */
-+} BOARD_PARAMETERS, *PBOARD_PARAMETERS;
-+
-+/* Variables */
-+#if defined(_BCM96338_) || defined(CONFIG_BCM96338)
-+static BOARD_PARAMETERS g_bcm96338sv =
-+{
-+ "96338SV", /* szBoardId */
-+ {{BP_ENET_INTERNAL_PHY, /* ucPhyType */
-+ 0x01, /* ucPhyAddress */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSck */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSs */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMosi */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMiso */
-+ BP_NOT_DEFINED, /* usGpioPhyReset */
-+ 0x01, /* numSwitchPorts */
-+ BP_ENET_CONFIG_MDIO, /* usConfigType */
-+ BP_NOT_DEFINED}, /* usReverseMii */
-+ {BP_ENET_NO_PHY}}, /* ucPhyType */
-+ {{BP_VOIP_NO_DSP}, /* ucDspType */
-+ {BP_VOIP_NO_DSP}}, /* ucDspType */
-+ BP_MEMORY_16MB_1_CHIP, /* usSdramSize */
-+ BP_PSI_DEFAULT_SIZE, /* usPsiSize */
-+ BP_NOT_DEFINED, /* usGpioRj11InnerPair */
-+ BP_NOT_DEFINED, /* usGpioRj11OuterPair */
-+ BP_NOT_DEFINED, /* usGpioPressAndHoldReset */
-+ BP_NOT_DEFINED, /* usGpioPcmciaReset */
-+ BP_NOT_DEFINED, /* usGpioUartRts */
-+ BP_NOT_DEFINED, /* usGpioUartCts */
-+ BP_NOT_DEFINED, /* usGpioLedAdsl */
-+ BP_NOT_DEFINED, /* usGpioLedAdslFail */
-+ BP_NOT_DEFINED, /* usGpioLedWireless */
-+ BP_NOT_DEFINED, /* usGpioLedUsb */
-+ BP_NOT_DEFINED, /* usGpioLedHpna */
-+ BP_NOT_DEFINED, /* usGpioLedWanData */
-+ BP_NOT_DEFINED, /* usGpioLedPpp */
-+ BP_NOT_DEFINED, /* usGpioLedPppFail */
-+ BP_NOT_DEFINED, /* usGpioLedBlPowerOn */
-+ BP_NOT_DEFINED, /* usGpioLedBlAlarm */
-+ BP_NOT_DEFINED, /* usGpioLedBlResetCfg */
-+ BP_NOT_DEFINED, /* usGpioLedBlStop */
-+ BP_NOT_DEFINED, /* usExtIntrWireless */
-+ BP_HW_DEFINED, /* usExtIntrAdslDyingGasp */
-+ BP_NOT_DEFINED, /* usExtIntrHpna */
-+ BP_NOT_DEFINED, /* usCsHpna */
-+ BP_NOT_DEFINED, /* usAntInUseWireless */
-+ BP_NOT_DEFINED, /* usGpioSesBtnWireless */
-+ BP_NOT_DEFINED, /* usExtIntrSesBtnWireless */
-+ BP_NOT_DEFINED /* usGpioLedSesWireless */
-+};
-+static BOARD_PARAMETERS g_bcm96338l2m8m =
-+{
-+ "96338L-2M-8M", /* szBoardId */
-+ {{BP_ENET_INTERNAL_PHY, /* ucPhyType */
-+ 0x01, /* ucPhyAddress */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSck */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSs */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMosi */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMiso */
-+ BP_NOT_DEFINED, /* usGpioPhyReset */
-+ 0x01, /* numSwitchPorts */
-+ BP_ENET_CONFIG_MDIO, /* usConfigType */
-+ BP_NOT_DEFINED}, /* usReverseMii */
-+ {BP_ENET_NO_PHY}}, /* ucPhyType */
-+ {{BP_VOIP_NO_DSP}, /* ucDspType */
-+ {BP_VOIP_NO_DSP}}, /* ucDspType */
-+ BP_MEMORY_8MB_1_CHIP, /* usSdramSize */
-+ BP_PSI_DEFAULT_SIZE, /* usPsiSize */
-+ BP_NOT_DEFINED, /* usGpioRj11InnerPair */
-+ BP_NOT_DEFINED, /* usGpioRj11OuterPair */
-+ BP_NOT_DEFINED, /* usGpioPressAndHoldReset */
-+ BP_NOT_DEFINED, /* usGpioPcmciaReset */
-+ BP_NOT_DEFINED, /* usGpioUartRts */
-+ BP_NOT_DEFINED, /* usGpioUartCts */
-+ BP_NOT_DEFINED, /* usGpioLedAdsl */
-+ BP_GPIO_2_AL, /* usGpioLedAdslFail */
-+ BP_NOT_DEFINED, /* usGpioLedWireless */
-+ BP_NOT_DEFINED, /* usGpioLedUsb */
-+ BP_NOT_DEFINED, /* usGpioLedHpna */
-+ BP_GPIO_3_AL, /* usGpioLedWanData */
-+ BP_GPIO_3_AL, /* usGpioLedPpp */
-+ BP_GPIO_4_AL, /* usGpioLedPppFail */
-+ BP_GPIO_0_AL, /* usGpioLedBlPowerOn */
-+ BP_NOT_DEFINED, /* usGpioLedBlAlarm */
-+ BP_GPIO_3_AL, /* usGpioLedBlResetCfg */
-+ BP_GPIO_1_AL, /* usGpioLedBlStop */
-+ BP_NOT_DEFINED, /* usExtIntrWireless */
-+ BP_HW_DEFINED, /* usExtIntrAdslDyingGasp */
-+ BP_NOT_DEFINED, /* usExtIntrHpna */
-+ BP_NOT_DEFINED, /* usCsHpna */
-+ BP_NOT_DEFINED, /* usAntInUseWireless */
-+ BP_NOT_DEFINED, /* usGpioSesBtnWireless */
-+ BP_NOT_DEFINED, /* usExtIntrSesBtnWireless */
-+ BP_NOT_DEFINED /* usGpioLedSesWireless */
-+};
-+static PBOARD_PARAMETERS g_BoardParms[] =
-+ {&g_bcm96338sv, &g_bcm96338l2m8m, 0};
-+#endif
-+
-+#if defined(_BCM96345_) || defined(CONFIG_BCM96345)
-+static BOARD_PARAMETERS g_bcm96345r =
-+{
-+ "96345R", /* szBoardId */
-+ {{BP_ENET_INTERNAL_PHY, /* ucPhyType */
-+ 0x01, /* ucPhyAddress */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSck */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSs */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMosi */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMiso */
-+ BP_NOT_DEFINED, /* usGpioPhyReset */
-+ 0x01, /* numSwitchPorts */
-+ BP_ENET_CONFIG_MDIO, /* usConfigType */
-+ BP_NOT_DEFINED}, /* usReverseMii */
-+ {BP_ENET_NO_PHY}}, /* ucPhyType */
-+ {{BP_VOIP_NO_DSP}, /* ucDspType */
-+ {BP_VOIP_NO_DSP}}, /* ucDspType */
-+ BP_MEMORY_8MB_1_CHIP, /* usSdramSize */
-+ BP_PSI_DEFAULT_SIZE, /* usPsiSize */
-+ BP_GPIO_11_AH, /* usGpioRj11InnerPair */
-+ BP_GPIO_12_AH, /* usGpioRj11OuterPair */
-+ BP_GPIO_13_AH, /* usGpioPressAndHoldReset */
-+ BP_NOT_DEFINED, /* usGpioPcmciaReset */
-+ BP_NOT_DEFINED, /* usGpioUartRts */
-+ BP_NOT_DEFINED, /* usGpioUartCts */
-+ BP_GPIO_8_AH, /* usGpioLedAdsl */
-+ BP_NOT_DEFINED, /* usGpioLedAdslFail */
-+ BP_NOT_DEFINED, /* usGpioLedWireless */
-+ BP_NOT_DEFINED, /* usGpioLedUsb */
-+ BP_NOT_DEFINED, /* usGpioLedHpna */
-+ BP_GPIO_8_AH, /* usGpioLedWanData */
-+ BP_GPIO_9_AH, /* usGpioLedPpp */
-+ BP_NOT_DEFINED, /* usGpioLedPppFail */
-+ BP_NOT_DEFINED, /* usGpioLedBlPowerOn */
-+ BP_GPIO_10_AH, /* usGpioLedBlAlarm */
-+ BP_GPIO_9_AH, /* usGpioLedBlResetCfg */
-+ BP_GPIO_8_AH, /* usGpioLedBlStop */
-+ BP_NOT_DEFINED, /* usExtIntrWireless */
-+ BP_EXT_INTR_0, /* usExtIntrAdslDyingGasp */
-+ BP_NOT_DEFINED, /* usExtIntrHpna */
-+ BP_NOT_DEFINED, /* usCsHpna */
-+ BP_NOT_DEFINED, /* usAntInUseWireless */
-+ BP_NOT_DEFINED, /* usGpioSesBtnWireless */
-+ BP_NOT_DEFINED, /* usExtIntrSesBtnWireless */
-+ BP_NOT_DEFINED /* usGpioLedSesWireless */
-+};
-+
-+static BOARD_PARAMETERS g_bcm96345gw2 =
-+{
-+ /* A hardware jumper determines whether GPIO 13 is used for Press and Hold
-+ * Reset or RTS.
-+ */
-+ "96345GW2", /* szBoardId */
-+ {{BP_ENET_EXTERNAL_SWITCH, /* ucPhyType */
-+ 0x00, /* ucPhyAddress */
-+ BP_GPIO_0_AH, /* usGpioPhySpiSck */
-+ BP_GPIO_4_AH, /* usGpioPhySpiSs */
-+ BP_GPIO_12_AH, /* usGpioPhySpiMosi */
-+ BP_GPIO_11_AH, /* usGpioPhySpiMiso */
-+ BP_NOT_DEFINED, /* usGpioPhyReset */
-+ 0x04, /* numSwitchPorts */
-+ BP_ENET_CONFIG_GPIO, /* usConfigType */
-+ BP_ENET_REVERSE_MII}, /* usReverseMii */
-+ {BP_ENET_NO_PHY}}, /* ucPhyType */
-+ {{BP_VOIP_DSP, /* ucDspType */
-+ 0x00, /* ucDspAddress */
-+ BP_EXT_INTR_1, /* usExtIntrVoip */
-+ BP_GPIO_6_AH, /* usGpioVoipReset */
-+ BP_GPIO_15_AH, /* usGpioVoipIntr */
-+ BP_NOT_DEFINED, /* usGpioLedVoip */
-+ BP_CS_2}, /* usCsVoip */
-+ {BP_VOIP_NO_DSP}}, /* ucDspType */
-+ BP_MEMORY_16MB_1_CHIP, /* usSdramSize */
-+ BP_PSI_DEFAULT_SIZE, /* usPsiSize */
-+ BP_NOT_DEFINED, /* usGpioRj11InnerPair */
-+ BP_NOT_DEFINED, /* usGpioRj11OuterPair */
-+ BP_GPIO_13_AH, /* usGpioPressAndHoldReset */
-+ BP_GPIO_2_AH, /* usGpioPcmciaReset */
-+ BP_GPIO_13_AH, /* usGpioUartRts */
-+ BP_GPIO_9_AH, /* usGpioUartCts */
-+ BP_GPIO_8_AH, /* usGpioLedAdsl */
-+ BP_NOT_DEFINED, /* usGpioLedAdslFail */
-+ BP_NOT_DEFINED, /* usGpioLedWireless */
-+ BP_GPIO_7_AH, /* usGpioLedUsb */
-+ BP_NOT_DEFINED, /* usGpioLedHpna */
-+ BP_GPIO_8_AH, /* usGpioLedWanData */
-+ BP_NOT_DEFINED, /* usGpioLedPpp */
-+ BP_NOT_DEFINED, /* usGpioLedPppFail */
-+ BP_NOT_DEFINED, /* usGpioLedBlPowerOn */
-+ BP_GPIO_10_AH, /* usGpioLedBlAlarm */
-+ BP_GPIO_7_AH, /* usGpioLedBlResetCfg */
-+ BP_GPIO_8_AH, /* usGpioLedBlStop */
-+ BP_EXT_INTR_2, /* usExtIntrWireless */
-+ BP_EXT_INTR_0, /* usExtIntrAdslDyingGasp */
-+ BP_NOT_DEFINED, /* usExtIntrHpna */
-+ BP_NOT_DEFINED, /* usCsHpna */
-+ BP_WLAN_ANT_MAIN, /* usAntInUseWireless */
-+ BP_NOT_DEFINED, /* usGpioSesBtnWireless */
-+ BP_NOT_DEFINED, /* usExtIntrSesBtnWireless */
-+ BP_NOT_DEFINED /* usGpioLedSesWireless */
-+};
-+
-+static BOARD_PARAMETERS g_bcm96345gw =
-+{
-+ "96345GW", /* szBoardId */
-+ {{BP_ENET_EXTERNAL_SWITCH, /* ucPhyType */
-+ 0x00, /* ucPhyAddress */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSck */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSs */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMosi */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMiso */
-+ BP_NOT_DEFINED, /* usGpioPhyReset */
-+ 0x04, /* numSwitchPorts */
-+ BP_ENET_CONFIG_MDIO, /* usConfigType */
-+ BP_ENET_NO_REVERSE_MII}, /* usReverseMii */
-+ {BP_ENET_NO_PHY}}, /* ucPhyType */
-+ {{BP_VOIP_DSP, /* ucDspType */
-+ 0x00, /* ucDspAddress */
-+ BP_EXT_INTR_1, /* usExtIntrVoip */
-+ BP_GPIO_6_AH, /* usGpioVoipReset */
-+ BP_GPIO_15_AH, /* usGpioVoipIntr */
-+ BP_NOT_DEFINED, /* usGpioLedVoip */
-+ BP_CS_2}, /* usCsVoip */
-+ {BP_VOIP_NO_DSP}}, /* ucDspType */
-+ BP_MEMORY_16MB_1_CHIP, /* usSdramSize */
-+ BP_PSI_DEFAULT_SIZE, /* usPsiSize */
-+ BP_GPIO_11_AH, /* usGpioRj11InnerPair */
-+ BP_GPIO_1_AH, /* usGpioRj11OuterPair */
-+ BP_GPIO_13_AH, /* usGpioPressAndHoldReset */
-+ BP_GPIO_2_AH, /* usGpioPcmciaReset */
-+ BP_NOT_DEFINED, /* usGpioUartRts */
-+ BP_NOT_DEFINED, /* usGpioUartCts */
-+ BP_GPIO_8_AH, /* usGpioLedAdsl */
-+ BP_NOT_DEFINED, /* usGpioLedAdslFail */
-+ BP_GPIO_10_AH, /* usGpioLedWireless */
-+ BP_GPIO_7_AH, /* usGpioLedUsb */
-+ BP_NOT_DEFINED, /* usGpioLedHpna */
-+ BP_GPIO_8_AH, /* usGpioLedWanData */
-+ BP_NOT_DEFINED, /* usGpioLedPpp */
-+ BP_NOT_DEFINED, /* usGpioLedPppFail */
-+ BP_NOT_DEFINED, /* usGpioLedBlPowerOn */
-+ BP_GPIO_9_AH, /* usGpioLedBlAlarm */
-+ BP_GPIO_10_AH, /* usGpioLedBlResetCfg */
-+ BP_GPIO_8_AH, /* usGpioLedBlStop */
-+ BP_EXT_INTR_2, /* usExtIntrWireless */
-+ BP_EXT_INTR_0, /* usExtIntrAdslDyingGasp */
-+ BP_EXT_INTR_3, /* usExtIntrHpna */
-+ BP_CS_1, /* usCsHpna */
-+ BP_WLAN_ANT_MAIN, /* usAntInUseWireless */
-+ BP_NOT_DEFINED, /* usGpioSesBtnWireless */
-+ BP_NOT_DEFINED, /* usExtIntrSesBtnWireless */
-+ BP_NOT_DEFINED /* usGpioLedSesWireless */
-+};
-+
-+static BOARD_PARAMETERS g_bcm96335r =
-+{
-+ "96335R", /* szBoardId */
-+ {{BP_ENET_INTERNAL_PHY, /* ucPhyType */
-+ 0x01, /* ucPhyAddress */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSck */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSs */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMosi */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMiso */
-+ BP_NOT_DEFINED, /* usGpioPhyReset */
-+ 0x01, /* numSwitchPorts */
-+ BP_ENET_CONFIG_MDIO, /* usConfigType */
-+ BP_NOT_DEFINED}, /* usReverseMii */
-+ {BP_ENET_NO_PHY}}, /* ucPhyType */
-+ {{BP_VOIP_NO_DSP}, /* ucDspType */
-+ {BP_VOIP_NO_DSP}}, /* ucDspType */
-+ BP_MEMORY_8MB_1_CHIP, /* usSdramSize */
-+ BP_PSI_DEFAULT_SIZE, /* usPsiSize */
-+ BP_NOT_DEFINED, /* usGpioRj11InnerPair */
-+ BP_NOT_DEFINED, /* usGpioRj11OuterPair */
-+ BP_GPIO_14_AH, /* usGpioPressAndHoldReset */
-+ BP_NOT_DEFINED, /* usGpioPcmciaReset */
-+ BP_NOT_DEFINED, /* usGpioUartRts */
-+ BP_NOT_DEFINED, /* usGpioUartCts */
-+ BP_GPIO_9_AH, /* usGpioLedAdsl */
-+ BP_NOT_DEFINED, /* usGpioLedAdslFail */
-+ BP_NOT_DEFINED, /* usGpioLedWireless */
-+ BP_NOT_DEFINED, /* usGpioLedUsb */
-+ BP_NOT_DEFINED, /* usGpioLedHpna */
-+ BP_GPIO_9_AH, /* usGpioLedWanData */
-+ BP_GPIO_8_AH, /* usGpioLedPpp */
-+ BP_NOT_DEFINED, /* usGpioLedPppFail */
-+ BP_NOT_DEFINED, /* usGpioLedBlPowerOn */
-+ BP_GPIO_10_AH, /* usGpioLedBlAlarm */
-+ BP_GPIO_8_AH, /* usGpioLedBlResetCfg */
-+ BP_GPIO_9_AH, /* usGpioLedBlStop */
-+ BP_NOT_DEFINED, /* usExtIntrWireless */
-+ BP_NOT_DEFINED, /* usExtIntrAdslDyingGasp */
-+ BP_NOT_DEFINED, /* usExtIntrHpna */
-+ BP_NOT_DEFINED, /* usCsHpna */
-+ BP_NOT_DEFINED, /* usAntInUseWireless */
-+ BP_NOT_DEFINED, /* usGpioSesBtnWireless */
-+ BP_NOT_DEFINED, /* usExtIntrSesBtnWireless */
-+ BP_NOT_DEFINED /* usGpioLedSesWireless */
-+};
-+
-+static BOARD_PARAMETERS g_bcm96345r0 =
-+{
-+ "96345R0", /* szBoardId */
-+ {{BP_ENET_INTERNAL_PHY, /* ucPhyType */
-+ 0x01, /* ucPhyAddress */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSck */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSs */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMosi */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMiso */
-+ BP_NOT_DEFINED, /* usGpioPhyReset */
-+ 0x01, /* numSwitchPorts */
-+ BP_ENET_CONFIG_MDIO, /* usConfigType */
-+ BP_NOT_DEFINED}, /* usReverseMii */
-+ {BP_ENET_NO_PHY}}, /* ucPhyType */
-+ {{BP_VOIP_NO_DSP}, /* ucDspType */
-+ {BP_VOIP_NO_DSP}}, /* ucDspType */
-+ BP_MEMORY_8MB_1_CHIP, /* usSdramSize */
-+ BP_PSI_DEFAULT_SIZE, /* usPsiSize */
-+ BP_NOT_DEFINED, /* usGpioRj11InnerPair */
-+ BP_NOT_DEFINED, /* usGpioRj11OuterPair */
-+ BP_NOT_DEFINED, /* usGpioPressAndHoldReset */
-+ BP_NOT_DEFINED, /* usGpioPcmciaReset */
-+ BP_NOT_DEFINED, /* usGpioUartRts */
-+ BP_NOT_DEFINED, /* usGpioUartCts */
-+ BP_GPIO_8_AH, /* usGpioLedAdsl */
-+ BP_NOT_DEFINED, /* usGpioLedAdslFail */
-+ BP_NOT_DEFINED, /* usGpioLedWireless */
-+ BP_NOT_DEFINED, /* usGpioLedUsb */
-+ BP_NOT_DEFINED, /* usGpioLedHpna */
-+ BP_GPIO_9_AH, /* usGpioLedWanData */
-+ BP_GPIO_9_AH, /* usGpioLedPpp */
-+ BP_NOT_DEFINED, /* usGpioLedPppFail */
-+ BP_NOT_DEFINED, /* usGpioLedBlPowerOn */
-+ BP_GPIO_9_AH, /* usGpioLedBlAlarm */
-+ BP_GPIO_8_AH, /* usGpioLedBlResetCfg */
-+ BP_GPIO_8_AH, /* usGpioLedBlStop */
-+ BP_NOT_DEFINED, /* usExtIntrWireless */
-+ BP_NOT_DEFINED, /* usExtIntrAdslDyingGasp */
-+ BP_NOT_DEFINED, /* usExtIntrHpna */
-+ BP_NOT_DEFINED, /* usCsHpna */
-+ BP_NOT_DEFINED, /* usAntInUseWireless */
-+ BP_NOT_DEFINED, /* usGpioSesBtnWireless */
-+ BP_NOT_DEFINED, /* usExtIntrSesBtnWireless */
-+ BP_NOT_DEFINED /* usGpioLedSesWireless */
-+};
-+
-+static BOARD_PARAMETERS g_bcm96345rs =
-+{
-+ "96345RS", /* szBoardId */
-+ {{BP_ENET_EXTERNAL_SWITCH, /* ucPhyType */
-+ 0x00, /* ucPhyAddress */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSck */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSs */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMosi */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMiso */
-+ BP_NOT_DEFINED, /* usGpioPhyReset */
-+ 0x01, /* numSwitchPorts */
-+ BP_ENET_CONFIG_MDIO, /* usConfigType */
-+ BP_ENET_NO_REVERSE_MII}, /* usReverseMii */
-+ {BP_ENET_NO_PHY}}, /* ucPhyType */
-+ {{BP_VOIP_NO_DSP}, /* ucDspType */
-+ {BP_VOIP_NO_DSP}}, /* ucDspType */
-+ BP_MEMORY_8MB_1_CHIP, /* usSdramSize */
-+ BP_PSI_DEFAULT_SIZE, /* usPsiSize */
-+ BP_GPIO_11_AH, /* usGpioRj11InnerPair */
-+ BP_GPIO_12_AH, /* usGpioRj11OuterPair */
-+ BP_GPIO_13_AH, /* usGpioPressAndHoldReset */
-+ BP_NOT_DEFINED, /* usGpioPcmciaReset */
-+ BP_NOT_DEFINED, /* usGpioUartRts */
-+ BP_NOT_DEFINED, /* usGpioUartCts */
-+ BP_GPIO_8_AH, /* usGpioLedAdsl */
-+ BP_NOT_DEFINED, /* usGpioLedAdslFail */
-+ BP_NOT_DEFINED, /* usGpioLedWireless */
-+ BP_NOT_DEFINED, /* usGpioLedUsb */
-+ BP_NOT_DEFINED, /* usGpioLedHpna */
-+ BP_GPIO_8_AH, /* usGpioLedWanData */
-+ BP_GPIO_9_AH, /* usGpioLedPpp */
-+ BP_NOT_DEFINED, /* usGpioLedPppFail */
-+ BP_NOT_DEFINED, /* usGpioLedBlPowerOn */
-+ BP_GPIO_10_AH, /* usGpioLedBlAlarm */
-+ BP_GPIO_9_AH, /* usGpioLedBlResetCfg */
-+ BP_GPIO_8_AH, /* usGpioLedBlStop */
-+ BP_NOT_DEFINED, /* usExtIntrWireless */
-+ BP_EXT_INTR_0, /* usExtIntrAdslDyingGasp */
-+ BP_NOT_DEFINED, /* usExtIntrHpna */
-+ BP_NOT_DEFINED, /* usCsHpna */
-+ BP_NOT_DEFINED, /* usAntInUseWireless */
-+ BP_NOT_DEFINED, /* usGpioSesBtnWireless */
-+ BP_NOT_DEFINED, /* usExtIntrSesBtnWireless */
-+ BP_NOT_DEFINED /* usGpioLedSesWireless */
-+};
-+
-+static PBOARD_PARAMETERS g_BoardParms[] =
-+ {&g_bcm96345r, &g_bcm96345gw2, &g_bcm96345gw, &g_bcm96335r, &g_bcm96345r0,
-+ &g_bcm96345rs, 0};
-+#endif
-+
-+#if defined(_BCM96348_) || defined(CONFIG_BCM96348)
-+
-+static BOARD_PARAMETERS g_bcm96348r =
-+{
-+ "96348R", /* szBoardId */
-+ {{BP_ENET_INTERNAL_PHY, /* ucPhyType */
-+ 0x01, /* ucPhyAddress */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSck */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSs */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMosi */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMiso */
-+ BP_NOT_DEFINED, /* usGpioPhyReset */
-+ 0x01, /* numSwitchPorts */
-+ BP_ENET_CONFIG_MDIO, /* usConfigType */
-+ BP_NOT_DEFINED}, /* usReverseMii */
-+ {BP_ENET_NO_PHY}}, /* ucPhyType */
-+ {{BP_VOIP_NO_DSP}, /* ucDspType */
-+ {BP_VOIP_NO_DSP}}, /* ucDspType */
-+ BP_MEMORY_8MB_1_CHIP, /* usSdramSize */
-+ BP_PSI_DEFAULT_SIZE, /* usPsiSize */
-+ BP_NOT_DEFINED, /* usGpioRj11InnerPair */
-+ BP_NOT_DEFINED, /* usGpioRj11OuterPair */
-+ BP_GPIO_7_AH, /* usGpioPressAndHoldReset */
-+ BP_NOT_DEFINED, /* usGpioPcmciaReset */
-+ BP_NOT_DEFINED, /* usGpioUartRts */
-+ BP_NOT_DEFINED, /* usGpioUartCts */
-+ BP_NOT_DEFINED, /* usGpioLedAdsl */
-+ BP_GPIO_2_AL, /* usGpioLedAdslFail */
-+ BP_NOT_DEFINED, /* usGpioLedWireless */
-+ BP_NOT_DEFINED, /* usGpioLedUsb */
-+ BP_NOT_DEFINED, /* usGpioLedHpna */
-+ BP_GPIO_3_AL, /* usGpioLedWanData */
-+ BP_GPIO_3_AL, /* usGpioLedPpp */
-+ BP_GPIO_4_AL, /* usGpioLedPppFail */
-+ BP_GPIO_0_AL, /* usGpioLedBlPowerOn */
-+ BP_NOT_DEFINED, /* usGpioLedBlAlarm */
-+ BP_GPIO_3_AL, /* usGpioLedBlResetCfg */
-+ BP_GPIO_1_AL, /* usGpioLedBlStop */
-+ BP_NOT_DEFINED, /* usExtIntrWireless */
-+ BP_HW_DEFINED, /* usExtIntrAdslDyingGasp */
-+ BP_NOT_DEFINED, /* usExtIntrHpna */
-+ BP_NOT_DEFINED, /* usCsHpna */
-+ BP_NOT_DEFINED, /* usAntInUseWireless */
-+ BP_NOT_DEFINED, /* usGpioSesBtnWireless */
-+ BP_NOT_DEFINED, /* usExtIntrSesBtnWireless */
-+ BP_NOT_DEFINED /* usGpioLedSesWireless */
-+};
-+
-+static BOARD_PARAMETERS g_bcm96348lv =
-+{
-+ "96348LV", /* szBoardId */
-+ {{BP_ENET_INTERNAL_PHY, /* ucPhyType */
-+ 0x01, /* ucPhyAddress */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSck */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSs */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMosi */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMiso */
-+ BP_NOT_DEFINED, /* usGpioPhyReset */
-+ 0x01, /* numSwitchPorts */
-+ BP_ENET_CONFIG_MDIO, /* usConfigType */
-+ BP_NOT_DEFINED}, /* usReverseMii */
-+ {BP_ENET_EXTERNAL_PHY, /* ucPhyType */
-+ 0x02, /* ucPhyAddress */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSck */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSs */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMosi */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMiso */
-+ BP_GPIO_5_AL, /* usGpioPhyReset */
-+ 0x01, /* numSwitchPorts */
-+ BP_ENET_CONFIG_MDIO, /* usConfigType */
-+ BP_NOT_DEFINED}}, /* usReverseMii */
-+ {{BP_VOIP_NO_DSP}, /* ucDspType */
-+ {BP_VOIP_NO_DSP}}, /* ucDspType */
-+ BP_MEMORY_16MB_2_CHIP, /* usSdramSize */
-+ BP_PSI_DEFAULT_SIZE, /* usPsiSize */
-+ BP_NOT_DEFINED, /* usGpioRj11InnerPair */
-+ BP_NOT_DEFINED, /* usGpioRj11OuterPair */
-+ BP_GPIO_7_AH, /* usGpioPressAndHoldReset */
-+ BP_NOT_DEFINED, /* usGpioPcmciaReset */
-+ BP_NOT_DEFINED, /* usGpioUartRts */
-+ BP_NOT_DEFINED, /* usGpioUartCts */
-+ BP_NOT_DEFINED, /* usGpioLedAdsl */
-+ BP_GPIO_2_AL, /* usGpioLedAdslFail */
-+ BP_NOT_DEFINED, /* usGpioLedWireless */
-+ BP_NOT_DEFINED, /* usGpioLedUsb */
-+ BP_NOT_DEFINED, /* usGpioLedHpna */
-+ BP_GPIO_3_AL, /* usGpioLedWanData */
-+ BP_GPIO_3_AL, /* usGpioLedPpp */
-+ BP_GPIO_4_AL, /* usGpioLedPppFail */
-+ BP_GPIO_0_AL, /* usGpioLedBlPowerOn */
-+ BP_NOT_DEFINED, /* usGpioLedBlAlarm */
-+ BP_GPIO_3_AL, /* usGpioLedBlResetCfg */
-+ BP_GPIO_1_AL, /* usGpioLedBlStop */
-+ BP_NOT_DEFINED, /* usExtIntrWireless */
-+ BP_NOT_DEFINED, /* usExtIntrAdslDyingGasp */
-+ BP_NOT_DEFINED, /* usExtIntrHpna */
-+ BP_NOT_DEFINED, /* usCsHpna */
-+ BP_NOT_DEFINED, /* usAntInUseWireless */
-+ BP_NOT_DEFINED, /* usGpioSesBtnWireless */
-+ BP_NOT_DEFINED, /* usExtIntrSesBtnWireless */
-+ BP_NOT_DEFINED /* usGpioLedSesWireless */
-+};
-+
-+static BOARD_PARAMETERS g_bcm96348gw =
-+{
-+ "96348GW", /* szBoardId */
-+ {{BP_ENET_INTERNAL_PHY, /* ucPhyType */
-+ 0x01, /* ucPhyAddress */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSck */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSs */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMosi */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMiso */
-+ BP_NOT_DEFINED, /* usGpioPhyReset */
-+ 0x01, /* numSwitchPorts */
-+ BP_ENET_CONFIG_MDIO, /* usConfigType */
-+ BP_NOT_DEFINED}, /* usReverseMii */
-+ {BP_ENET_EXTERNAL_SWITCH, /* ucPhyType */
-+ 0x00, /* ucPhyAddress */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSck */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSs */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMosi */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMiso */
-+ BP_NOT_DEFINED, /* usGpioPhyReset */
-+ 0x03, /* numSwitchPorts */
-+ BP_ENET_CONFIG_SPI_SSB_0, /* usConfigType */
-+ BP_ENET_REVERSE_MII}}, /* usReverseMii */
-+ {{BP_VOIP_DSP, /* ucDspType */
-+ 0x00, /* ucDspAddress */
-+ BP_EXT_INTR_2, /* usExtIntrVoip */
-+ BP_GPIO_6_AH, /* usGpioVoipReset */
-+ BP_GPIO_34_AH, /* usGpioVoipIntr */
-+ BP_NOT_DEFINED, /* usGpioLedVoip */
-+ BP_CS_2}, /* usCsVoip */
-+ {BP_VOIP_NO_DSP}}, /* ucDspType */
-+ BP_MEMORY_16MB_2_CHIP, /* usSdramSize */
-+ BP_PSI_DEFAULT_SIZE, /* usPsiSize */
-+ BP_NOT_DEFINED, /* usGpioRj11InnerPair */
-+ BP_NOT_DEFINED, /* usGpioRj11OuterPair */
-+ BP_GPIO_33_AL, /* usGpioPressAndHoldReset */
-+ BP_NOT_DEFINED, /* usGpioPcmciaReset */
-+ BP_NOT_DEFINED, /* usGpioUartRts */
-+ BP_NOT_DEFINED, /* usGpioUartCts */
-+ BP_NOT_DEFINED, /* usGpioLedAdsl */
-+ BP_GPIO_2_AL, /* usGpioLedAdslFail */
-+ BP_NOT_DEFINED, /* usGpioLedWireless */
-+ BP_NOT_DEFINED, /* usGpioLedUsb */
-+ BP_NOT_DEFINED, /* usGpioLedHpna */
-+ BP_GPIO_3_AL, /* usGpioLedWanData */
-+ BP_GPIO_3_AL, /* usGpioLedPpp */
-+ BP_GPIO_4_AL, /* usGpioLedPppFail */
-+ BP_GPIO_0_AL, /* usGpioLedBlPowerOn */
-+ BP_NOT_DEFINED, /* usGpioLedBlAlarm */
-+ BP_GPIO_3_AL, /* usGpioLedBlResetCfg */
-+ BP_GPIO_1_AL, /* usGpioLedBlStop */
-+ BP_NOT_DEFINED, /* usExtIntrWireless */
-+ BP_HW_DEFINED, /* usExtIntrAdslDyingGasp */
-+ BP_NOT_DEFINED, /* usExtIntrHpna */
-+ BP_NOT_DEFINED, /* usCsHpna */
-+ BP_WLAN_ANT_MAIN, /* usAntInUseWireless */
-+ BP_NOT_DEFINED, /* BP_GPIO_35_AH, */ /* usGpioSesBtnWireless */
-+ BP_NOT_DEFINED, /* BP_EXT_INTR_3, */ /* usExtIntrSesBtnWireless */
-+ BP_NOT_DEFINED /* BP_GPIO_0_AL */ /* usGpioLedSesWireless */
-+};
-+
-+
-+static BOARD_PARAMETERS g_bcm96348gw_10 =
-+{
-+ "96348GW-10", /* szBoardId */
-+ {{BP_ENET_INTERNAL_PHY, /* ucPhyType */
-+ 0x01, /* ucPhyAddress */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSck */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSs */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMosi */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMiso */
-+ BP_NOT_DEFINED, /* usGpioPhyReset */
-+ 0x01, /* numSwitchPorts */
-+ BP_ENET_CONFIG_MDIO, /* usConfigType */
-+ BP_NOT_DEFINED}, /* usReverseMii */
-+ {BP_ENET_EXTERNAL_SWITCH, /* ucPhyType */
-+ 0x00, /* ucPhyAddress */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSck */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSs */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMosi */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMiso */
-+ BP_NOT_DEFINED, /* usGpioPhyReset */
-+ 0x03, /* numSwitchPorts */
-+ BP_ENET_CONFIG_SPI_SSB_1, /* usConfigType */
-+ BP_ENET_REVERSE_MII}}, /* usReverseMii */
-+ {{BP_VOIP_DSP, /* ucDspType */
-+ 0x00, /* ucDspAddress */
-+ BP_EXT_INTR_2, /* usExtIntrVoip */
-+ BP_GPIO_6_AH, /* usGpioVoipReset */
-+ BP_GPIO_34_AH, /* usGpioVoipIntr */
-+ BP_NOT_DEFINED, /* usGpioLedVoip */
-+ BP_CS_2}, /* usCsVoip */
-+ {BP_VOIP_NO_DSP}}, /* ucDspType */
-+ BP_MEMORY_16MB_2_CHIP, /* usSdramSize */
-+ BP_PSI_DEFAULT_SIZE, /* usPsiSize */
-+ BP_NOT_DEFINED, /* usGpioRj11InnerPair */
-+ BP_NOT_DEFINED, /* usGpioRj11OuterPair */
-+ BP_GPIO_33_AL, /* usGpioPressAndHoldReset */
-+ BP_NOT_DEFINED, /* usGpioPcmciaReset */
-+ BP_NOT_DEFINED, /* usGpioUartRts */
-+ BP_NOT_DEFINED, /* usGpioUartCts */
-+ BP_NOT_DEFINED, /* usGpioLedAdsl */
-+ BP_GPIO_2_AL, /* usGpioLedAdslFail */
-+ BP_NOT_DEFINED, /* usGpioLedWireless */
-+ BP_NOT_DEFINED, /* usGpioLedUsb */
-+ BP_NOT_DEFINED, /* usGpioLedHpna */
-+ BP_GPIO_3_AL, /* usGpioLedWanData */
-+ BP_GPIO_3_AL, /* usGpioLedPpp */
-+ BP_GPIO_4_AL, /* usGpioLedPppFail */
-+ BP_GPIO_0_AL, /* usGpioLedBlPowerOn */
-+ BP_NOT_DEFINED, /* usGpioLedBlAlarm */
-+ BP_GPIO_3_AL, /* usGpioLedBlResetCfg */
-+ BP_GPIO_1_AL, /* usGpioLedBlStop */
-+ BP_NOT_DEFINED, /* usExtIntrWireless */
-+ BP_HW_DEFINED, /* usExtIntrAdslDyingGasp */
-+ BP_NOT_DEFINED, /* usExtIntrHpna */
-+ BP_NOT_DEFINED, /* usCsHpna */
-+ BP_WLAN_ANT_MAIN, /* usAntInUseWireless */
-+ BP_NOT_DEFINED, /* usGpioSesBtnWireless */
-+ BP_NOT_DEFINED, /* usExtIntrSesBtnWireless */
-+ BP_NOT_DEFINED /* usGpioLedSesWireless */
-+};
-+
-+static BOARD_PARAMETERS g_bcm96348gw_11 =
-+{
-+ "96348GW-11", /* szBoardId */
-+ {{BP_ENET_NO_PHY}, /* ucPhyType */
-+ {BP_ENET_EXTERNAL_SWITCH, /* ucPhyType */
-+ 0x00, /* ucPhyAddress */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSck */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSs */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMosi */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMiso */
-+ BP_NOT_DEFINED, /* usGpioPhyReset */
-+ 0x04, /* numSwitchPorts */
-+ BP_ENET_CONFIG_SPI_SSB_1, /* usConfigType */
-+ BP_ENET_REVERSE_MII}}, /* usReverseMii */
-+ {{BP_VOIP_NO_DSP}, /* ucDspType */
-+ {BP_VOIP_NO_DSP}}, /* ucDspType */
-+ BP_MEMORY_16MB_2_CHIP, /* usSdramSize */
-+ BP_PSI_DEFAULT_SIZE, /* usPsiSize */
-+ BP_NOT_DEFINED, /* usGpioRj11InnerPair */
-+ BP_NOT_DEFINED, /* usGpioRj11OuterPair */
-+ BP_GPIO_33_AL, /* usGpioPressAndHoldReset */
-+ BP_NOT_DEFINED, /* usGpioPcmciaReset */
-+ BP_NOT_DEFINED, /* usGpioUartRts */
-+ BP_NOT_DEFINED, /* usGpioUartCts */
-+ BP_NOT_DEFINED, /* usGpioLedAdsl */
-+ BP_GPIO_2_AL, /* usGpioLedAdslFail */
-+ BP_NOT_DEFINED, /* usGpioLedWireless */
-+ BP_NOT_DEFINED, /* usGpioLedUsb */
-+ BP_NOT_DEFINED, /* usGpioLedHpna */
-+ BP_GPIO_3_AL, /* usGpioLedWanData */
-+ BP_GPIO_3_AL, /* usGpioLedPpp */
-+ BP_GPIO_4_AL, /* usGpioLedPppFail */
-+ BP_GPIO_0_AL, /* usGpioLedBlPowerOn */
-+ BP_NOT_DEFINED, /* usGpioLedBlAlarm */
-+ BP_GPIO_3_AL, /* usGpioLedBlResetCfg */
-+ BP_GPIO_1_AL, /* usGpioLedBlStop */
-+ BP_NOT_DEFINED, /* usExtIntrWireless */
-+ BP_HW_DEFINED, /* usExtIntrAdslDyingGasp */
-+ BP_NOT_DEFINED, /* usExtIntrHpna */
-+ BP_NOT_DEFINED, /* usCsHpna */
-+ BP_NOT_DEFINED, /* usAntInUseWireless */
-+ BP_NOT_DEFINED, /* usGpioSesBtnWireless */
-+ BP_NOT_DEFINED, /* usExtIntrSesBtnWireless */
-+ BP_NOT_DEFINED /* usGpioLedSesWireless */
-+};
-+
-+static BOARD_PARAMETERS g_bcm96348sv =
-+{
-+ "96348SV", /* szBoardId */
-+ {{BP_ENET_INTERNAL_PHY, /* ucPhyType */
-+ 0x01, /* ucPhyAddress */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSck */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSs */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMosi */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMiso */
-+ BP_NOT_DEFINED, /* usGpioPhyReset */
-+ 0x01, /* numSwitchPorts */
-+ BP_ENET_CONFIG_MDIO, /* usConfigType */
-+ BP_NOT_DEFINED}, /* usReverseMii */
-+ {BP_ENET_EXTERNAL_PHY, /* ucPhyType */
-+ 0x1f, /* ucPhyAddress */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSck */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSs */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMosi */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMiso */
-+ BP_NOT_DEFINED, /* usGpioPhyReset */
-+ 0x01, /* numSwitchPorts */
-+ BP_ENET_CONFIG_MDIO, /* usConfigType */
-+ BP_NOT_DEFINED}}, /* usReverseMii */
-+ {{BP_VOIP_NO_DSP}, /* ucDspType */
-+ {BP_VOIP_NO_DSP}}, /* ucDspType */
-+ BP_MEMORY_32MB_2_CHIP, /* usSdramSize */
-+ BP_PSI_DEFAULT_SIZE, /* usPsiSize */
-+ BP_NOT_DEFINED, /* usGpioRj11InnerPair */
-+ BP_NOT_DEFINED, /* usGpioRj11OuterPair */
-+ BP_NOT_DEFINED, /* usGpioPressAndHoldReset */
-+ BP_NOT_DEFINED, /* usGpioPcmciaReset */
-+ BP_NOT_DEFINED, /* usGpioUartRts */
-+ BP_NOT_DEFINED, /* usGpioUartCts */
-+ BP_NOT_DEFINED, /* usGpioLedAdsl */
-+ BP_NOT_DEFINED, /* usGpioLedAdslFail */
-+ BP_NOT_DEFINED, /* usGpioLedWireless */
-+ BP_NOT_DEFINED, /* usGpioLedUsb */
-+ BP_NOT_DEFINED, /* usGpioLedHpna */
-+ BP_NOT_DEFINED, /* usGpioLedWanData */
-+ BP_NOT_DEFINED, /* usGpioLedPpp */
-+ BP_NOT_DEFINED, /* usGpioLedPppFail */
-+ BP_NOT_DEFINED, /* usGpioLedBlPowerOn */
-+ BP_NOT_DEFINED, /* usGpioLedBlAlarm */
-+ BP_NOT_DEFINED, /* usGpioLedBlResetCfg */
-+ BP_NOT_DEFINED, /* usGpioLedBlStop */
-+ BP_NOT_DEFINED, /* usExtIntrWireless */
-+ BP_HW_DEFINED, /* usExtIntrAdslDyingGasp */
-+ BP_NOT_DEFINED, /* usExtIntrHpna */
-+ BP_NOT_DEFINED, /* usCsHpna */
-+ BP_NOT_DEFINED, /* usAntInUseWireless */
-+ BP_NOT_DEFINED, /* usGpioSesBtnWireless */
-+ BP_NOT_DEFINED, /* usExtIntrSesBtnWireless */
-+ BP_NOT_DEFINED /* usGpioLedSesWireless */
-+};
-+
-+
-+static BOARD_PARAMETERS g_bcm96348gw_dualDsp =
-+{
-+ "96348GW-DualDSP", /* szBoardId */
-+ {{BP_ENET_INTERNAL_PHY, /* ucPhyType */
-+ 0x01, /* ucPhyAddress */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSck */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSs */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMosi */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMiso */
-+ BP_NOT_DEFINED, /* usGpioPhyReset */
-+ 0x01, /* numSwitchPorts */
-+ BP_ENET_CONFIG_MDIO, /* usConfigType */
-+ BP_NOT_DEFINED}, /* usReverseMii */
-+ {BP_ENET_EXTERNAL_SWITCH, /* ucPhyType */
-+ 0x00, /* ucPhyAddress */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSck */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSs */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMosi */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMiso */
-+ BP_NOT_DEFINED, /* usGpioPhyReset */
-+ 0x03, /* numSwitchPorts */
-+ BP_ENET_CONFIG_SPI_SSB_1, /* usConfigType */
-+ BP_ENET_REVERSE_MII}}, /* usReverseMii */
-+ {{BP_VOIP_DSP, /* ucDspType */
-+ 0x00, /* ucDspAddress */
-+ BP_EXT_INTR_2, /* usExtIntrVoip */
-+ BP_UNEQUIPPED, /* usGpioVoipReset */
-+ BP_GPIO_34_AH, /* usGpioVoipIntr */
-+ BP_NOT_DEFINED, /* usGpioLedVoip */
-+ BP_CS_2}, /* usCsVoip */
-+ {BP_VOIP_DSP, /* ucDspType */
-+ 0x01, /* ucDspAddress */
-+ BP_EXT_INTR_3, /* usExtIntrVoip */
-+ BP_UNEQUIPPED , /* usGpioVoipReset */
-+ BP_GPIO_35_AH, /* usGpioVoipIntr */
-+ BP_NOT_DEFINED, /* usGpioLedVoip */
-+ BP_CS_3}}, /* usCsVoip */
-+ BP_MEMORY_16MB_2_CHIP, /* usSdramSize */
-+ BP_PSI_DEFAULT_SIZE, /* usPsiSize */
-+ BP_NOT_DEFINED, /* usGpioRj11InnerPair */
-+ BP_NOT_DEFINED, /* usGpioRj11OuterPair */
-+ BP_GPIO_33_AL, /* usGpioPressAndHoldReset */
-+ BP_NOT_DEFINED, /* usGpioPcmciaReset */
-+ BP_NOT_DEFINED, /* usGpioUartRts */
-+ BP_NOT_DEFINED, /* usGpioUartCts */
-+ BP_NOT_DEFINED, /* usGpioLedAdsl */
-+ BP_GPIO_2_AL, /* usGpioLedAdslFail */
-+ BP_NOT_DEFINED, /* usGpioLedWireless */
-+ BP_NOT_DEFINED, /* usGpioLedUsb */
-+ BP_NOT_DEFINED, /* usGpioLedHpna */
-+ BP_GPIO_3_AL, /* usGpioLedWanData */
-+ BP_GPIO_3_AL, /* usGpioLedPpp */
-+ BP_GPIO_4_AL, /* usGpioLedPppFail */
-+ BP_GPIO_0_AL, /* usGpioLedBlPowerOn */
-+ BP_NOT_DEFINED, /* usGpioLedBlAlarm */
-+ BP_GPIO_3_AL, /* usGpioLedBlResetCfg */
-+ BP_GPIO_1_AL, /* usGpioLedBlStop */
-+ BP_NOT_DEFINED, /* usExtIntrWireless */
-+ BP_HW_DEFINED, /* usExtIntrAdslDyingGasp */
-+ BP_NOT_DEFINED, /* usExtIntrHpna */
-+ BP_NOT_DEFINED, /* usCsHpna */
-+ BP_WLAN_ANT_MAIN, /* usAntInUseWireless */
-+ BP_NOT_DEFINED, /* usGpioSesBtnWireless */
-+ BP_NOT_DEFINED, /* usExtIntrSesBtnWireless */
-+ BP_NOT_DEFINED /* usGpioLedSesWireless */
-+};
-+
-+
-+static BOARD_PARAMETERS g_bcmCustom_01 =
-+{
-+ "BCMCUST_01", /* szBoardId */
-+ {{BP_ENET_INTERNAL_PHY, /* ucPhyType */
-+ 0x01, /* ucPhyAddress */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSck */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSs */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMosi */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMiso */
-+ BP_NOT_DEFINED, /* usGpioPhyReset */
-+ 0x01, /* numSwitchPorts */
-+ BP_ENET_CONFIG_MDIO, /* usConfigType */
-+ BP_NOT_DEFINED}, /* usReverseMii */
-+ {BP_ENET_NO_PHY, /* ucPhyType */
-+ 0x00, /* ucPhyAddress */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSck */
-+ BP_NOT_DEFINED, /* usGpioPhySpiSs */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMosi */
-+ BP_NOT_DEFINED, /* usGpioPhySpiMiso */
-+ BP_NOT_DEFINED, /* usGpioPhyReset */
-+ 0x01, /* numSwitchPorts */
-+ BP_ENET_CONFIG_SPI_SSB_1, /* usConfigType */
-+ BP_ENET_REVERSE_MII}}, /* usReverseMii */
-+ {{BP_VOIP_DSP, /* ucDspType */
-+ 0x00, /* ucDspAddress */
-+ BP_EXT_INTR_2, /* usExtIntrVoip */
-+ BP_GPIO_36_AH, /* usGpioVoipReset */
-+ BP_GPIO_34_AL, /* usGpioVoipIntr */
-+ BP_NOT_DEFINED, /* usGpioLedVoip */
-+ BP_CS_2}, /* usCsVoip */
-+ {BP_VOIP_NO_DSP}}, /* ucDspType */
-+ BP_MEMORY_16MB_2_CHIP, /* usSdramSize */
-+ BP_PSI_DEFAULT_SIZE, /* usPsiSize */
-+ BP_NOT_DEFINED, /* usGpioRj11InnerPair */
-+ BP_NOT_DEFINED, /* usGpioRj11OuterPair */
-+ BP_GPIO_33_AL, /* usGpioPressAndHoldReset */
-+ BP_NOT_DEFINED, /* usGpioPcmciaReset */
-+ BP_NOT_DEFINED, /* usGpioUartRts */
-+ BP_NOT_DEFINED, /* usGpioUartCts */
-+ BP_NOT_DEFINED, /* usGpioLedAdsl */
-+ BP_GPIO_2_AL, /* usGpioLedAdslFail */
-+ BP_NOT_DEFINED, /* usGpioLedWireless */
-+ BP_NOT_DEFINED, /* usGpioLedUsb */
-+ BP_NOT_DEFINED, /* usGpioLedHpna */
-+ BP_GPIO_3_AL, /* usGpioLedWanData */
-+ BP_GPIO_3_AL, /* usGpioLedPpp */
-+ BP_GPIO_4_AL, /* usGpioLedPppFail */
-+ BP_GPIO_0_AL, /* usGpioLedBlPowerOn */
-+ BP_NOT_DEFINED, /* usGpioLedBlAlarm */
-+ BP_GPIO_3_AL, /* usGpioLedBlResetCfg */
-+ BP_GPIO_1_AL, /* usGpioLedBlStop */
-+ BP_NOT_DEFINED, /* usExtIntrWireless */
-+ BP_NOT_DEFINED, /* usExtIntrAdslDyingGasp */
-+ BP_NOT_DEFINED, /* usExtIntrHpna */
-+ BP_NOT_DEFINED, /* usCsHpna */
-+ BP_NOT_DEFINED, /* usAntInUseWireless */
-+ BP_NOT_DEFINED, /* usGpioSesBtnWireless */
-+ BP_NOT_DEFINED, /* usExtIntrSesBtnWireless */
-+ BP_NOT_DEFINED /* usGpioLedSesWireless */
-+};
-+
-+static PBOARD_PARAMETERS g_BoardParms[] =
-+ {&g_bcm96348r, &g_bcm96348lv, &g_bcm96348gw, &g_bcm96348gw_10,
-+ &g_bcm96348gw_11, &g_bcm96348sv, &g_bcm96348gw_dualDsp,
-+ &g_bcmCustom_01, 0};
-+#endif
-+
-+static PBOARD_PARAMETERS g_pCurrentBp = 0;
-+
-+/**************************************************************************
-+ * Name : bpstrcmp
-+ *
-+ * Description: String compare for this file so it does not depend on an OS.
-+ * (Linux kernel and CFE share this source file.)
-+ *
-+ * Parameters : [IN] dest - destination string
-+ * [IN] src - source string
-+ *
-+ * Returns : -1 - dest < src, 1 - dest > src, 0 dest == src
-+ ***************************************************************************/
-+static int bpstrcmp(const char *dest,const char *src);
-+static int bpstrcmp(const char *dest,const char *src)
-+{
-+ while (*src && *dest)
-+ {
-+ if (*dest < *src) return -1;
-+ if (*dest > *src) return 1;
-+ dest++;
-+ src++;
-+ }
-+
-+ if (*dest && !*src) return 1;
-+ if (!*dest && *src) return -1;
-+ return 0;
-+} /* bpstrcmp */
-+
-+/**************************************************************************
-+ * Name : BpGetVoipDspConfig
-+ *
-+ * Description: Gets the DSP configuration from the board parameter
-+ * structure for a given DSP index.
-+ *
-+ * Parameters : [IN] dspNum - DSP index (number)
-+ *
-+ * Returns : Pointer to DSP configuration block if found/valid, NULL
-+ * otherwise.
-+ ***************************************************************************/
-+VOIP_DSP_INFO *BpGetVoipDspConfig( unsigned char dspNum );
-+VOIP_DSP_INFO *BpGetVoipDspConfig( unsigned char dspNum )
-+{
-+ VOIP_DSP_INFO *pDspConfig = 0;
-+ int i;
-+
-+ if( g_pCurrentBp )
-+ {
-+ for( i = 0 ; i < BP_MAX_VOIP_DSP ; i++ )
-+ {
-+ if( g_pCurrentBp->VoIPDspInfo[i].ucDspType != BP_VOIP_NO_DSP &&
-+ g_pCurrentBp->VoIPDspInfo[i].ucDspAddress == dspNum )
-+ {
-+ pDspConfig = &g_pCurrentBp->VoIPDspInfo[i];
-+ break;
-+ }
-+ }
-+ }
-+
-+ return pDspConfig;
-+}
-+
-+
-+/**************************************************************************
-+ * Name : BpSetBoardId
-+ *
-+ * Description: This function find the BOARD_PARAMETERS structure for the
-+ * specified board id string and assigns it to a global, static
-+ * variable.
-+ *
-+ * Parameters : [IN] pszBoardId - Board id string that is saved into NVRAM.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_FOUND - Error, board id input string does not
-+ * have a board parameters configuration record.
-+ ***************************************************************************/
-+int BpSetBoardId( char *pszBoardId )
-+{
-+ int nRet = BP_BOARD_ID_NOT_FOUND;
-+ PBOARD_PARAMETERS *ppBp;
-+
-+ for( ppBp = g_BoardParms; *ppBp; ppBp++ )
-+ {
-+ if( !bpstrcmp((*ppBp)->szBoardId, pszBoardId) )
-+ {
-+ g_pCurrentBp = *ppBp;
-+ nRet = BP_SUCCESS;
-+ break;
-+ }
-+ }
-+
-+ return( nRet );
-+} /* BpSetBoardId */
-+
-+/**************************************************************************
-+ * Name : BpGetBoardIds
-+ *
-+ * Description: This function returns all of the supported board id strings.
-+ *
-+ * Parameters : [OUT] pszBoardIds - Address of a buffer that the board id
-+ * strings are returned in. Each id starts at BP_BOARD_ID_LEN
-+ * boundary.
-+ * [IN] nBoardIdsSize - Number of BP_BOARD_ID_LEN elements that
-+ * were allocated in pszBoardIds.
-+ *
-+ * Returns : Number of board id strings returned.
-+ ***************************************************************************/
-+int BpGetBoardIds( char *pszBoardIds, int nBoardIdsSize )
-+{
-+ PBOARD_PARAMETERS *ppBp;
-+ int i;
-+ char *src;
-+ char *dest;
-+
-+ for( i = 0, ppBp = g_BoardParms; *ppBp && nBoardIdsSize;
-+ i++, ppBp++, nBoardIdsSize--, pszBoardIds += BP_BOARD_ID_LEN )
-+ {
-+ dest = pszBoardIds;
-+ src = (*ppBp)->szBoardId;
-+ while( *src )
-+ *dest++ = *src++;
-+ *dest = '\0';
-+ }
-+
-+ return( i );
-+} /* BpGetBoardIds */
-+
-+/**************************************************************************
-+ * Name : BpGetEthernetMacInfo
-+ *
-+ * Description: This function returns all of the supported board id strings.
-+ *
-+ * Parameters : [OUT] pEnetInfos - Address of an array of ETHERNET_MAC_INFO
-+ * buffers.
-+ * [IN] nNumEnetInfos - Number of ETHERNET_MAC_INFO elements that
-+ * are pointed to by pEnetInfos.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ ***************************************************************************/
-+int BpGetEthernetMacInfo( PETHERNET_MAC_INFO pEnetInfos, int nNumEnetInfos )
-+{
-+ int i, nRet;
-+
-+ if( g_pCurrentBp )
-+ {
-+ for( i = 0; i < nNumEnetInfos; i++, pEnetInfos++ )
-+ {
-+ if( i < BP_MAX_ENET_MACS )
-+ {
-+ unsigned char *src = (unsigned char *)
-+ &g_pCurrentBp->EnetMacInfos[i];
-+ unsigned char *dest = (unsigned char *) pEnetInfos;
-+ int len = sizeof(ETHERNET_MAC_INFO);
-+ while( len-- )
-+ *dest++ = *src++;
-+ }
-+ else
-+ pEnetInfos->ucPhyType = BP_ENET_NO_PHY;
-+ }
-+
-+ nRet = BP_SUCCESS;
-+ }
-+ else
-+ {
-+ for( i = 0; i < nNumEnetInfos; i++, pEnetInfos++ )
-+ pEnetInfos->ucPhyType = BP_ENET_NO_PHY;
-+
-+ nRet = BP_BOARD_ID_NOT_SET;
-+ }
-+
-+ return( nRet );
-+} /* BpGetEthernetMacInfo */
-+
-+/**************************************************************************
-+ * Name : BpGetSdramSize
-+ *
-+ * Description: This function returns a constant that describees the board's
-+ * SDRAM type and size.
-+ *
-+ * Parameters : [OUT] pulSdramSize - Address of short word that the SDRAM size
-+ * is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ ***************************************************************************/
-+int BpGetSdramSize( unsigned long *pulSdramSize )
-+{
-+ int nRet;
-+
-+ if( g_pCurrentBp )
-+ {
-+ *pulSdramSize = g_pCurrentBp->usSdramSize;
-+ nRet = BP_SUCCESS;
-+ }
-+ else
-+ {
-+ *pulSdramSize = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_SET;
-+ }
-+
-+ return( nRet );
-+} /* BpGetSdramSize */
-+
-+/**************************************************************************
-+ * Name : BpGetPsiSize
-+ *
-+ * Description: This function returns the persistent storage size in K bytes.
-+ *
-+ * Parameters : [OUT] pulPsiSize - Address of short word that the persistent
-+ * storage size is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ ***************************************************************************/
-+int BpGetPsiSize( unsigned long *pulPsiSize )
-+{
-+ int nRet;
-+
-+ if( g_pCurrentBp )
-+ {
-+ *pulPsiSize = g_pCurrentBp->usPsiSize;
-+ nRet = BP_SUCCESS;
-+ }
-+ else
-+ {
-+ *pulPsiSize = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_SET;
-+ }
-+
-+ return( nRet );
-+} /* BpGetPsiSize */
-+
-+/**************************************************************************
-+ * Name : BpGetRj11InnerOuterPairGpios
-+ *
-+ * Description: This function returns the GPIO pin assignments for changing
-+ * between the RJ11 inner pair and RJ11 outer pair.
-+ *
-+ * Parameters : [OUT] pusInner - Address of short word that the RJ11 inner pair
-+ * GPIO pin is returned in.
-+ * [OUT] pusOuter - Address of short word that the RJ11 outer pair
-+ * GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, values are returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetRj11InnerOuterPairGpios( unsigned short *pusInner,
-+ unsigned short *pusOuter )
-+{
-+ int nRet;
-+
-+ if( g_pCurrentBp )
-+ {
-+ *pusInner = g_pCurrentBp->usGpioRj11InnerPair;
-+ *pusOuter = g_pCurrentBp->usGpioRj11OuterPair;
-+
-+ if( g_pCurrentBp->usGpioRj11InnerPair != BP_NOT_DEFINED &&
-+ g_pCurrentBp->usGpioRj11OuterPair != BP_NOT_DEFINED )
-+ {
-+ nRet = BP_SUCCESS;
-+ }
-+ else
-+ {
-+ nRet = BP_VALUE_NOT_DEFINED;
-+ }
-+ }
-+ else
-+ {
-+ *pusInner = *pusOuter = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_SET;
-+ }
-+
-+ return( nRet );
-+} /* BpGetRj11InnerOuterPairGpios */
-+
-+/**************************************************************************
-+ * Name : BpGetPressAndHoldResetGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the press
-+ * and hold reset button.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the press and hold
-+ * reset button GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetPressAndHoldResetGpio( unsigned short *pusValue )
-+{
-+ int nRet;
-+
-+ if( g_pCurrentBp )
-+ {
-+ *pusValue = g_pCurrentBp->usGpioPressAndHoldReset;
-+
-+ if( g_pCurrentBp->usGpioPressAndHoldReset != BP_NOT_DEFINED )
-+ {
-+ nRet = BP_SUCCESS;
-+ }
-+ else
-+ {
-+ nRet = BP_VALUE_NOT_DEFINED;
-+ }
-+ }
-+ else
-+ {
-+ *pusValue = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_SET;
-+ }
-+
-+ return( nRet );
-+} /* BpGetPressAndHoldResetGpio */
-+
-+/**************************************************************************
-+ * Name : BpGetVoipResetGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the VOIP
-+ * Reset operation.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the VOIP reset
-+ * GPIO pin is returned in.
-+ * [IN] dspNum - Address of the DSP to query.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetVoipResetGpio( unsigned char dspNum, unsigned short *pusValue )
-+{
-+ int nRet;
-+
-+ if( g_pCurrentBp )
-+ {
-+ VOIP_DSP_INFO *pDspInfo = BpGetVoipDspConfig( dspNum );
-+
-+ if( pDspInfo )
-+ {
-+ *pusValue = pDspInfo->usGpioVoipReset;
-+
-+ if( *pusValue != BP_NOT_DEFINED ||
-+ *pusValue == BP_UNEQUIPPED )
-+ {
-+ nRet = BP_SUCCESS;
-+ }
-+ else
-+ {
-+ nRet = BP_VALUE_NOT_DEFINED;
-+ }
-+ }
-+ else
-+ {
-+ *pusValue = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_FOUND;
-+ }
-+ }
-+ else
-+ {
-+ *pusValue = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_SET;
-+ }
-+
-+ return( nRet );
-+} /* BpGetVoipResetGpio */
-+
-+/**************************************************************************
-+ * Name : BpGetVoipIntrGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for VoIP interrupt.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the VOIP interrupt
-+ * GPIO pin is returned in.
-+ * [IN] dspNum - Address of the DSP to query.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetVoipIntrGpio( unsigned char dspNum, unsigned short *pusValue )
-+{
-+ int nRet;
-+
-+ if( g_pCurrentBp )
-+ {
-+ VOIP_DSP_INFO *pDspInfo = BpGetVoipDspConfig( dspNum );
-+
-+ if( pDspInfo )
-+ {
-+ *pusValue = pDspInfo->usGpioVoipIntr;
-+
-+ if( *pusValue != BP_NOT_DEFINED )
-+ {
-+ nRet = BP_SUCCESS;
-+ }
-+ else
-+ {
-+ nRet = BP_VALUE_NOT_DEFINED;
-+ }
-+ }
-+ else
-+ {
-+ *pusValue = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_FOUND;
-+ }
-+ }
-+ else
-+ {
-+ *pusValue = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_SET;
-+ }
-+
-+ return( nRet );
-+} /* BpGetVoipIntrGpio */
-+
-+/**************************************************************************
-+ * Name : BpGetPcmciaResetGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the PCMCIA
-+ * Reset operation.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the PCMCIA reset
-+ * GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetPcmciaResetGpio( unsigned short *pusValue )
-+{
-+ int nRet;
-+
-+ if( g_pCurrentBp )
-+ {
-+ *pusValue = g_pCurrentBp->usGpioPcmciaReset;
-+
-+ if( g_pCurrentBp->usGpioPcmciaReset != BP_NOT_DEFINED )
-+ {
-+ nRet = BP_SUCCESS;
-+ }
-+ else
-+ {
-+ nRet = BP_VALUE_NOT_DEFINED;
-+ }
-+ }
-+ else
-+ {
-+ *pusValue = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_SET;
-+ }
-+
-+ return( nRet );
-+} /* BpGetPcmciaResetGpio */
-+
-+/**************************************************************************
-+ * Name : BpGetUartRtsCtsGpios
-+ *
-+ * Description: This function returns the GPIO pin assignments for RTS and CTS
-+ * UART signals.
-+ *
-+ * Parameters : [OUT] pusRts - Address of short word that the UART RTS GPIO
-+ * pin is returned in.
-+ * [OUT] pusCts - Address of short word that the UART CTS GPIO
-+ * pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, values are returned.
-+ * BP_BOARD_ID_NOT_SET - Error, board id input string does not
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetRtsCtsUartGpios( unsigned short *pusRts, unsigned short *pusCts )
-+{
-+ int nRet;
-+
-+ if( g_pCurrentBp )
-+ {
-+ *pusRts = g_pCurrentBp->usGpioUartRts;
-+ *pusCts = g_pCurrentBp->usGpioUartCts;
-+
-+ if( g_pCurrentBp->usGpioUartRts != BP_NOT_DEFINED &&
-+ g_pCurrentBp->usGpioUartCts != BP_NOT_DEFINED )
-+ {
-+ nRet = BP_SUCCESS;
-+ }
-+ else
-+ {
-+ nRet = BP_VALUE_NOT_DEFINED;
-+ }
-+ }
-+ else
-+ {
-+ *pusRts = *pusCts = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_SET;
-+ }
-+
-+ return( nRet );
-+} /* BpGetUartRtsCtsGpios */
-+
-+/**************************************************************************
-+ * Name : BpGetAdslLedGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the ADSL
-+ * LED.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the ADSL LED
-+ * GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetAdslLedGpio( unsigned short *pusValue )
-+{
-+ int nRet;
-+
-+ if( g_pCurrentBp )
-+ {
-+ *pusValue = g_pCurrentBp->usGpioLedAdsl;
-+
-+ if( g_pCurrentBp->usGpioLedAdsl != BP_NOT_DEFINED )
-+ {
-+ nRet = BP_SUCCESS;
-+ }
-+ else
-+ {
-+ nRet = BP_VALUE_NOT_DEFINED;
-+ }
-+ }
-+ else
-+ {
-+ *pusValue = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_SET;
-+ }
-+
-+ return( nRet );
-+} /* BpGetAdslLedGpio */
-+
-+/**************************************************************************
-+ * Name : BpGetAdslFailLedGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the ADSL
-+ * LED that is used when there is a DSL connection failure.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the ADSL LED
-+ * GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetAdslFailLedGpio( unsigned short *pusValue )
-+{
-+ int nRet;
-+
-+ if( g_pCurrentBp )
-+ {
-+ *pusValue = g_pCurrentBp->usGpioLedAdslFail;
-+
-+ if( g_pCurrentBp->usGpioLedAdslFail != BP_NOT_DEFINED )
-+ {
-+ nRet = BP_SUCCESS;
-+ }
-+ else
-+ {
-+ nRet = BP_VALUE_NOT_DEFINED;
-+ }
-+ }
-+ else
-+ {
-+ *pusValue = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_SET;
-+ }
-+
-+ return( nRet );
-+} /* BpGetAdslFailLedGpio */
-+
-+/**************************************************************************
-+ * Name : BpGetWirelessLedGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the Wireless
-+ * LED.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the Wireless LED
-+ * GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetWirelessLedGpio( unsigned short *pusValue )
-+{
-+ int nRet;
-+
-+ if( g_pCurrentBp )
-+ {
-+ *pusValue = g_pCurrentBp->usGpioLedWireless;
-+
-+ if( g_pCurrentBp->usGpioLedWireless != BP_NOT_DEFINED )
-+ {
-+ nRet = BP_SUCCESS;
-+ }
-+ else
-+ {
-+ nRet = BP_VALUE_NOT_DEFINED;
-+ }
-+ }
-+ else
-+ {
-+ *pusValue = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_SET;
-+ }
-+
-+ return( nRet );
-+} /* BpGetWirelessLedGpio */
-+
-+/**************************************************************************
-+ * Name : BpGetWirelessAntInUse
-+ *
-+ * Description: This function returns the antennas in use for wireless
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the Wireless Antenna
-+ * is in use.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetWirelessAntInUse( unsigned short *pusValue )
-+{
-+ int nRet;
-+
-+ if( g_pCurrentBp )
-+ {
-+ *pusValue = g_pCurrentBp->usAntInUseWireless;
-+
-+ if( g_pCurrentBp->usAntInUseWireless != BP_NOT_DEFINED )
-+ {
-+ nRet = BP_SUCCESS;
-+ }
-+ else
-+ {
-+ nRet = BP_VALUE_NOT_DEFINED;
-+ }
-+ }
-+ else
-+ {
-+ *pusValue = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_SET;
-+ }
-+
-+ return( nRet );
-+} /* BpGetWirelessAntInUse */
-+
-+/**************************************************************************
-+ * Name : BpGetWirelessSesBtnGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the Wireless
-+ * Ses Button.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the Wireless LED
-+ * GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetWirelessSesBtnGpio( unsigned short *pusValue )
-+{
-+ int nRet;
-+
-+ if( g_pCurrentBp )
-+ {
-+ *pusValue = g_pCurrentBp->usGpioSesBtnWireless;
-+
-+ if( g_pCurrentBp->usGpioSesBtnWireless != BP_NOT_DEFINED )
-+ {
-+ nRet = BP_SUCCESS;
-+ }
-+ else
-+ {
-+ nRet = BP_VALUE_NOT_DEFINED;
-+ }
-+ }
-+ else
-+ {
-+ *pusValue = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_SET;
-+ }
-+
-+ return( nRet );
-+} /* BpGetWirelessSesBtnGpio */
-+
-+/**************************************************************************
-+ * Name : BpGetWirelessSesExtIntr
-+ *
-+ * Description: This function returns the external interrupt number for the
-+ * Wireless Ses Button.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the Wireless Ses
-+ * external interrup is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetWirelessSesExtIntr( unsigned short *pusValue )
-+{
-+ int nRet;
-+
-+ if( g_pCurrentBp )
-+ {
-+ *pusValue = g_pCurrentBp->usExtIntrSesBtnWireless;
-+
-+ if( g_pCurrentBp->usExtIntrSesBtnWireless != BP_NOT_DEFINED )
-+ {
-+ nRet = BP_SUCCESS;
-+ }
-+ else
-+ {
-+ nRet = BP_VALUE_NOT_DEFINED;
-+ }
-+ }
-+ else
-+ {
-+ *pusValue = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_SET;
-+ }
-+
-+ return( nRet );
-+
-+} /* BpGetWirelessSesExtIntr */
-+
-+/**************************************************************************
-+ * Name : BpGetWirelessSesLedGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the Wireless
-+ * Ses Led.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the Wireless Ses
-+ * Led GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetWirelessSesLedGpio( unsigned short *pusValue )
-+{
-+ int nRet;
-+
-+ if( g_pCurrentBp )
-+ {
-+ *pusValue = g_pCurrentBp->usGpioLedSesWireless;
-+
-+ if( g_pCurrentBp->usGpioLedSesWireless != BP_NOT_DEFINED )
-+ {
-+ nRet = BP_SUCCESS;
-+ }
-+ else
-+ {
-+ nRet = BP_VALUE_NOT_DEFINED;
-+ }
-+ }
-+ else
-+ {
-+ *pusValue = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_SET;
-+ }
-+
-+ return( nRet );
-+
-+} /* BpGetWirelessSesLedGpio */
-+
-+/**************************************************************************
-+ * Name : BpGetUsbLedGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the USB
-+ * LED.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the USB LED
-+ * GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetUsbLedGpio( unsigned short *pusValue )
-+{
-+ int nRet;
-+
-+ if( g_pCurrentBp )
-+ {
-+ *pusValue = g_pCurrentBp->usGpioLedUsb;
-+
-+ if( g_pCurrentBp->usGpioLedUsb != BP_NOT_DEFINED )
-+ {
-+ nRet = BP_SUCCESS;
-+ }
-+ else
-+ {
-+ nRet = BP_VALUE_NOT_DEFINED;
-+ }
-+ }
-+ else
-+ {
-+ *pusValue = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_SET;
-+ }
-+
-+ return( nRet );
-+} /* BpGetUsbLedGpio */
-+
-+/**************************************************************************
-+ * Name : BpGetHpnaLedGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the HPNA
-+ * LED.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the HPNA LED
-+ * GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetHpnaLedGpio( unsigned short *pusValue )
-+{
-+ int nRet;
-+
-+ if( g_pCurrentBp )
-+ {
-+ *pusValue = g_pCurrentBp->usGpioLedHpna;
-+
-+ if( g_pCurrentBp->usGpioLedHpna != BP_NOT_DEFINED )
-+ {
-+ nRet = BP_SUCCESS;
-+ }
-+ else
-+ {
-+ nRet = BP_VALUE_NOT_DEFINED;
-+ }
-+ }
-+ else
-+ {
-+ *pusValue = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_SET;
-+ }
-+
-+ return( nRet );
-+} /* BpGetHpnaLedGpio */
-+
-+/**************************************************************************
-+ * Name : BpGetWanDataLedGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the WAN Data
-+ * LED.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the WAN Data LED
-+ * GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetWanDataLedGpio( unsigned short *pusValue )
-+{
-+ int nRet;
-+
-+ if( g_pCurrentBp )
-+ {
-+ *pusValue = g_pCurrentBp->usGpioLedWanData;
-+
-+ if( g_pCurrentBp->usGpioLedWanData != BP_NOT_DEFINED )
-+ {
-+ nRet = BP_SUCCESS;
-+ }
-+ else
-+ {
-+ nRet = BP_VALUE_NOT_DEFINED;
-+ }
-+ }
-+ else
-+ {
-+ *pusValue = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_SET;
-+ }
-+
-+ return( nRet );
-+} /* BpGetWanDataLedGpio */
-+
-+/**************************************************************************
-+ * Name : BpGetPppLedGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the PPP
-+ * LED.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the PPP LED
-+ * GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetPppLedGpio( unsigned short *pusValue )
-+{
-+ int nRet;
-+
-+ if( g_pCurrentBp )
-+ {
-+ *pusValue = g_pCurrentBp->usGpioLedPpp;
-+
-+ if( g_pCurrentBp->usGpioLedPpp != BP_NOT_DEFINED )
-+ {
-+ nRet = BP_SUCCESS;
-+ }
-+ else
-+ {
-+ nRet = BP_VALUE_NOT_DEFINED;
-+ }
-+ }
-+ else
-+ {
-+ *pusValue = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_SET;
-+ }
-+
-+ return( nRet );
-+} /* BpGetPppLedGpio */
-+
-+/**************************************************************************
-+ * Name : BpGetPppFailLedGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the PPP
-+ * LED that is used when there is a PPP connection failure.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the PPP LED
-+ * GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetPppFailLedGpio( unsigned short *pusValue )
-+{
-+ int nRet;
-+
-+ if( g_pCurrentBp )
-+ {
-+ *pusValue = g_pCurrentBp->usGpioLedPppFail;
-+
-+ if( g_pCurrentBp->usGpioLedPppFail != BP_NOT_DEFINED )
-+ {
-+ nRet = BP_SUCCESS;
-+ }
-+ else
-+ {
-+ nRet = BP_VALUE_NOT_DEFINED;
-+ }
-+ }
-+ else
-+ {
-+ *pusValue = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_SET;
-+ }
-+
-+ return( nRet );
-+} /* BpGetPppFailLedGpio */
-+
-+/**************************************************************************
-+ * Name : BpGetBootloaderPowerOnLedGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the power
-+ * on LED that is set by the bootloader.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the alarm LED
-+ * GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetBootloaderPowerOnLedGpio( unsigned short *pusValue )
-+{
-+ int nRet;
-+
-+ if( g_pCurrentBp )
-+ {
-+ *pusValue = g_pCurrentBp->usGpioLedBlPowerOn;
-+
-+ if( g_pCurrentBp->usGpioLedBlPowerOn != BP_NOT_DEFINED )
-+ {
-+ nRet = BP_SUCCESS;
-+ }
-+ else
-+ {
-+ nRet = BP_VALUE_NOT_DEFINED;
-+ }
-+ }
-+ else
-+ {
-+ *pusValue = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_SET;
-+ }
-+
-+ return( nRet );
-+} /* BpGetBootloaderPowerOn */
-+
-+/**************************************************************************
-+ * Name : BpGetBootloaderAlarmLedGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the alarm
-+ * LED that is set by the bootloader.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the alarm LED
-+ * GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetBootloaderAlarmLedGpio( unsigned short *pusValue )
-+{
-+ int nRet;
-+
-+ if( g_pCurrentBp )
-+ {
-+ *pusValue = g_pCurrentBp->usGpioLedBlAlarm;
-+
-+ if( g_pCurrentBp->usGpioLedBlAlarm != BP_NOT_DEFINED )
-+ {
-+ nRet = BP_SUCCESS;
-+ }
-+ else
-+ {
-+ nRet = BP_VALUE_NOT_DEFINED;
-+ }
-+ }
-+ else
-+ {
-+ *pusValue = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_SET;
-+ }
-+
-+ return( nRet );
-+} /* BpGetBootloaderAlarmLedGpio */
-+
-+/**************************************************************************
-+ * Name : BpGetBootloaderResetCfgLedGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the reset
-+ * configuration LED that is set by the bootloader.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the reset
-+ * configuration LED GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetBootloaderResetCfgLedGpio( unsigned short *pusValue )
-+{
-+ int nRet;
-+
-+ if( g_pCurrentBp )
-+ {
-+ *pusValue = g_pCurrentBp->usGpioLedBlResetCfg;
-+
-+ if( g_pCurrentBp->usGpioLedBlResetCfg != BP_NOT_DEFINED )
-+ {
-+ nRet = BP_SUCCESS;
-+ }
-+ else
-+ {
-+ nRet = BP_VALUE_NOT_DEFINED;
-+ }
-+ }
-+ else
-+ {
-+ *pusValue = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_SET;
-+ }
-+
-+ return( nRet );
-+} /* BpGetBootloaderResetCfgLedGpio */
-+
-+/**************************************************************************
-+ * Name : BpGetBootloaderStopLedGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the break
-+ * into bootloader LED that is set by the bootloader.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the break into
-+ * bootloader LED GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetBootloaderStopLedGpio( unsigned short *pusValue )
-+{
-+ int nRet;
-+
-+ if( g_pCurrentBp )
-+ {
-+ *pusValue = g_pCurrentBp->usGpioLedBlStop;
-+
-+ if( g_pCurrentBp->usGpioLedBlStop != BP_NOT_DEFINED )
-+ {
-+ nRet = BP_SUCCESS;
-+ }
-+ else
-+ {
-+ nRet = BP_VALUE_NOT_DEFINED;
-+ }
-+ }
-+ else
-+ {
-+ *pusValue = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_SET;
-+ }
-+
-+ return( nRet );
-+} /* BpGetBootloaderStopLedGpio */
-+
-+/**************************************************************************
-+ * Name : BpGetVoipLedGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the VOIP
-+ * LED.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the VOIP LED
-+ * GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ *
-+ * Note : The VoIP structure would allow for having one LED per DSP
-+ * however, the board initialization function assumes only one
-+ * LED per functionality (ie one LED for VoIP). Therefore in
-+ * order to keep this tidy and simple we do not make usage of the
-+ * one-LED-per-DSP function. Instead, we assume that the LED for
-+ * VoIP is unique and associated with DSP 0 (always present on
-+ * any VoIP platform). If changing this to a LED-per-DSP function
-+ * then one need to update the board initialization driver in
-+ * bcmdrivers\opensource\char\board\bcm963xx\impl1
-+ ***************************************************************************/
-+int BpGetVoipLedGpio( unsigned short *pusValue )
-+{
-+ int nRet;
-+
-+ if( g_pCurrentBp )
-+ {
-+ VOIP_DSP_INFO *pDspInfo = BpGetVoipDspConfig( 0 );
-+
-+ if( pDspInfo )
-+ {
-+ *pusValue = pDspInfo->usGpioLedVoip;
-+
-+ if( *pusValue != BP_NOT_DEFINED )
-+ {
-+ nRet = BP_SUCCESS;
-+ }
-+ else
-+ {
-+ nRet = BP_VALUE_NOT_DEFINED;
-+ }
-+ }
-+ else
-+ {
-+ *pusValue = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_FOUND;
-+ }
-+ }
-+ else
-+ {
-+ *pusValue = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_SET;
-+ }
-+
-+ return( nRet );
-+} /* BpGetVoipLedGpio */
-+
-+/**************************************************************************
-+ * Name : BpGetWirelessExtIntr
-+ *
-+ * Description: This function returns the Wireless external interrupt number.
-+ *
-+ * Parameters : [OUT] pulValue - Address of short word that the wireless
-+ * external interrupt number is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetWirelessExtIntr( unsigned long *pulValue )
-+{
-+ int nRet;
-+
-+ if( g_pCurrentBp )
-+ {
-+ *pulValue = g_pCurrentBp->usExtIntrWireless;
-+
-+ if( g_pCurrentBp->usExtIntrWireless != BP_NOT_DEFINED )
-+ {
-+ nRet = BP_SUCCESS;
-+ }
-+ else
-+ {
-+ nRet = BP_VALUE_NOT_DEFINED;
-+ }
-+ }
-+ else
-+ {
-+ *pulValue = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_SET;
-+ }
-+
-+ return( nRet );
-+} /* BpGetWirelessExtIntr */
-+
-+/**************************************************************************
-+ * Name : BpGetAdslDyingGaspExtIntr
-+ *
-+ * Description: This function returns the ADSL Dying Gasp external interrupt
-+ * number.
-+ *
-+ * Parameters : [OUT] pulValue - Address of short word that the ADSL Dying Gasp
-+ * external interrupt number is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetAdslDyingGaspExtIntr( unsigned long *pulValue )
-+{
-+ int nRet;
-+
-+ if( g_pCurrentBp )
-+ {
-+ *pulValue = g_pCurrentBp->usExtIntrAdslDyingGasp;
-+
-+ if( g_pCurrentBp->usExtIntrAdslDyingGasp != BP_NOT_DEFINED )
-+ {
-+ nRet = BP_SUCCESS;
-+ }
-+ else
-+ {
-+ nRet = BP_VALUE_NOT_DEFINED;
-+ }
-+ }
-+ else
-+ {
-+ *pulValue = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_SET;
-+ }
-+
-+ return( nRet );
-+} /* BpGetAdslDyingGaspExtIntr */
-+
-+/**************************************************************************
-+ * Name : BpGetVoipExtIntr
-+ *
-+ * Description: This function returns the VOIP external interrupt number.
-+ *
-+ * Parameters : [OUT] pulValue - Address of short word that the VOIP
-+ * external interrupt number is returned in.
-+ * [IN] dspNum - Address of the DSP to query.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetVoipExtIntr( unsigned char dspNum, unsigned long *pulValue )
-+{
-+ int nRet;
-+
-+ if( g_pCurrentBp )
-+ {
-+ VOIP_DSP_INFO *pDspInfo = BpGetVoipDspConfig( dspNum );
-+
-+ if( pDspInfo )
-+ {
-+ *pulValue = pDspInfo->usExtIntrVoip;
-+
-+ if( *pulValue != BP_NOT_DEFINED )
-+ {
-+ nRet = BP_SUCCESS;
-+ }
-+ else
-+ {
-+ nRet = BP_VALUE_NOT_DEFINED;
-+ }
-+ }
-+ else
-+ {
-+ *pulValue = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_FOUND;
-+ }
-+ }
-+ else
-+ {
-+ *pulValue = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_SET;
-+ }
-+
-+ return( nRet );
-+} /* BpGetVoipExtIntr */
-+
-+/**************************************************************************
-+ * Name : BpGetHpnaExtIntr
-+ *
-+ * Description: This function returns the HPNA external interrupt number.
-+ *
-+ * Parameters : [OUT] pulValue - Address of short word that the HPNA
-+ * external interrupt number is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetHpnaExtIntr( unsigned long *pulValue )
-+{
-+ int nRet;
-+
-+ if( g_pCurrentBp )
-+ {
-+ *pulValue = g_pCurrentBp->usExtIntrHpna;
-+
-+ if( g_pCurrentBp->usExtIntrHpna != BP_NOT_DEFINED )
-+ {
-+ nRet = BP_SUCCESS;
-+ }
-+ else
-+ {
-+ nRet = BP_VALUE_NOT_DEFINED;
-+ }
-+ }
-+ else
-+ {
-+ *pulValue = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_SET;
-+ }
-+
-+ return( nRet );
-+} /* BpGetHpnaExtIntr */
-+
-+/**************************************************************************
-+ * Name : BpGetHpnaChipSelect
-+ *
-+ * Description: This function returns the HPNA chip select number.
-+ *
-+ * Parameters : [OUT] pulValue - Address of short word that the HPNA
-+ * chip select number is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetHpnaChipSelect( unsigned long *pulValue )
-+{
-+ int nRet;
-+
-+ if( g_pCurrentBp )
-+ {
-+ *pulValue = g_pCurrentBp->usCsHpna;
-+
-+ if( g_pCurrentBp->usCsHpna != BP_NOT_DEFINED )
-+ {
-+ nRet = BP_SUCCESS;
-+ }
-+ else
-+ {
-+ nRet = BP_VALUE_NOT_DEFINED;
-+ }
-+ }
-+ else
-+ {
-+ *pulValue = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_SET;
-+ }
-+
-+ return( nRet );
-+} /* BpGetHpnaChipSelect */
-+
-+/**************************************************************************
-+ * Name : BpGetVoipChipSelect
-+ *
-+ * Description: This function returns the VOIP chip select number.
-+ *
-+ * Parameters : [OUT] pulValue - Address of short word that the VOIP
-+ * chip select number is returned in.
-+ * [IN] dspNum - Address of the DSP to query.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetVoipChipSelect( unsigned char dspNum, unsigned long *pulValue )
-+{
-+ int nRet;
-+
-+ if( g_pCurrentBp )
-+ {
-+ VOIP_DSP_INFO *pDspInfo = BpGetVoipDspConfig( dspNum );
-+
-+ if( pDspInfo )
-+ {
-+ *pulValue = pDspInfo->usCsVoip;
-+
-+ if( *pulValue != BP_NOT_DEFINED )
-+ {
-+ nRet = BP_SUCCESS;
-+ }
-+ else
-+ {
-+ nRet = BP_VALUE_NOT_DEFINED;
-+ }
-+ }
-+ else
-+ {
-+ *pulValue = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_FOUND;
-+ }
-+ }
-+ else
-+ {
-+ *pulValue = BP_NOT_DEFINED;
-+ nRet = BP_BOARD_ID_NOT_SET;
-+ }
-+
-+ return( nRet );
-+} /* BpGetVoipChipSelect */
-+
-diff -urN linux-2.6.19/arch/mips/bcm963xx/boardparms.h linux-2.6.19.new/arch/mips/bcm963xx/boardparms.h
---- linux-2.6.19/arch/mips/bcm963xx/boardparms.h 1970-01-01 01:00:00.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/bcm963xx/boardparms.h 2006-12-16 18:46:31.000000000 +0100
-@@ -0,0 +1,758 @@
-+/*
-+<:copyright-gpl
-+
-+ Copyright 2003 Broadcom Corp. All Rights Reserved.
-+
-+ This program is free software; you can distribute it and/or modify it
-+ under the terms of the GNU General Public License (Version 2) as
-+ published by the Free Software Foundation.
-+
-+ This program is distributed in the hope it will be useful, but WITHOUT
-+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-+ for more details.
-+
-+ You should have received a copy of the GNU General Public License along
-+ with this program; if not, write to the Free Software Foundation, Inc.,
-+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-+
-+:>
-+*/
-+/**************************************************************************
-+ * File Name : boardparms.h
-+ *
-+ * Description: This file contains definitions and function prototypes for
-+ * the BCM63xx board parameter access functions.
-+ *
-+ * Updates : 07/14/2003 Created.
-+ ***************************************************************************/
-+
-+#if !defined(_BOARDPARMS_H)
-+#define _BOARDPARMS_H
-+
-+/* Return codes. */
-+#define BP_SUCCESS 0
-+#define BP_BOARD_ID_NOT_FOUND 1
-+#define BP_VALUE_NOT_DEFINED 2
-+#define BP_BOARD_ID_NOT_SET 3
-+
-+/* Values for BpGetSdramSize. */
-+#define BP_MEMORY_8MB_1_CHIP 0
-+#define BP_MEMORY_16MB_1_CHIP 1
-+#define BP_MEMORY_32MB_1_CHIP 2
-+#define BP_MEMORY_64MB_2_CHIP 3
-+#define BP_MEMORY_32MB_2_CHIP 4
-+#define BP_MEMORY_16MB_2_CHIP 5
-+
-+/* Values for EthernetMacInfo PhyType. */
-+#define BP_ENET_NO_PHY 0
-+#define BP_ENET_INTERNAL_PHY 1
-+#define BP_ENET_EXTERNAL_PHY 2
-+#define BP_ENET_EXTERNAL_SWITCH 3
-+
-+/* Values for EthernetMacInfo Configuration type. */
-+#define BP_ENET_CONFIG_MDIO 0 /* Internal PHY, External PHY, Switch+(no GPIO, no SPI, no MDIO Pseudo phy */
-+#define BP_ENET_CONFIG_GPIO 1 /* Bcm96345GW board + Bcm5325M/E */
-+#define BP_ENET_CONFIG_MDIO_PSEUDO_PHY 2 /* Bcm96348GW board + Bcm5325E */
-+#define BP_ENET_CONFIG_SPI_SSB_0 3 /* Bcm96348GW board + Bcm5325M/E */
-+#define BP_ENET_CONFIG_SPI_SSB_1 4 /* Bcm96348GW board + Bcm5325M/E */
-+#define BP_ENET_CONFIG_SPI_SSB_2 5 /* Bcm96348GW board + Bcm5325M/E */
-+#define BP_ENET_CONFIG_SPI_SSB_3 6 /* Bcm96348GW board + Bcm5325M/E */
-+
-+/* Values for EthernetMacInfo Reverse MII. */
-+#define BP_ENET_NO_REVERSE_MII 0
-+#define BP_ENET_REVERSE_MII 1
-+
-+/* Values for VoIPDSPInfo DSPType. */
-+#define BP_VOIP_NO_DSP 0
-+#define BP_VOIP_DSP 1
-+
-+
-+/* Values for GPIO pin assignments (AH = Active High, AL = Active Low). */
-+#define BP_ACTIVE_MASK 0x8000
-+#define BP_ACTIVE_HIGH 0x0000
-+#define BP_ACTIVE_LOW 0x8000
-+#define BP_GPIO_0_AH (0 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_0_AL (0 | BP_ACTIVE_LOW)
-+#define BP_GPIO_1_AH (1 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_1_AL (1 | BP_ACTIVE_LOW)
-+#define BP_GPIO_2_AH (2 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_2_AL (2 | BP_ACTIVE_LOW)
-+#define BP_GPIO_3_AH (3 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_3_AL (3 | BP_ACTIVE_LOW)
-+#define BP_GPIO_4_AH (4 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_4_AL (4 | BP_ACTIVE_LOW)
-+#define BP_GPIO_5_AH (5 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_5_AL (5 | BP_ACTIVE_LOW)
-+#define BP_GPIO_6_AH (6 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_6_AL (6 | BP_ACTIVE_LOW)
-+#define BP_GPIO_7_AH (7 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_7_AL (7 | BP_ACTIVE_LOW)
-+#define BP_GPIO_8_AH (8 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_8_AL (8 | BP_ACTIVE_LOW)
-+#define BP_GPIO_9_AH (9 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_9_AL (9 | BP_ACTIVE_LOW)
-+#define BP_GPIO_10_AH (10 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_10_AL (10 | BP_ACTIVE_LOW)
-+#define BP_GPIO_11_AH (11 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_11_AL (11 | BP_ACTIVE_LOW)
-+#define BP_GPIO_12_AH (12 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_12_AL (12 | BP_ACTIVE_LOW)
-+#define BP_GPIO_13_AH (13 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_13_AL (13 | BP_ACTIVE_LOW)
-+#define BP_GPIO_14_AH (14 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_14_AL (14 | BP_ACTIVE_LOW)
-+#define BP_GPIO_15_AH (15 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_15_AL (15 | BP_ACTIVE_LOW)
-+#define BP_GPIO_16_AH (16 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_16_AL (16 | BP_ACTIVE_LOW)
-+#define BP_GPIO_17_AH (17 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_17_AL (17 | BP_ACTIVE_LOW)
-+#define BP_GPIO_18_AH (18 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_18_AL (18 | BP_ACTIVE_LOW)
-+#define BP_GPIO_19_AH (19 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_19_AL (19 | BP_ACTIVE_LOW)
-+#define BP_GPIO_20_AH (20 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_20_AL (20 | BP_ACTIVE_LOW)
-+#define BP_GPIO_21_AH (21 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_21_AL (21 | BP_ACTIVE_LOW)
-+#define BP_GPIO_22_AH (22 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_22_AL (22 | BP_ACTIVE_LOW)
-+#define BP_GPIO_23_AH (23 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_23_AL (23 | BP_ACTIVE_LOW)
-+#define BP_GPIO_24_AH (24 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_24_AL (24 | BP_ACTIVE_LOW)
-+#define BP_GPIO_25_AH (25 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_25_AL (25 | BP_ACTIVE_LOW)
-+#define BP_GPIO_26_AH (26 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_26_AL (26 | BP_ACTIVE_LOW)
-+#define BP_GPIO_27_AH (27 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_27_AL (27 | BP_ACTIVE_LOW)
-+#define BP_GPIO_28_AH (28 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_28_AL (28 | BP_ACTIVE_LOW)
-+#define BP_GPIO_29_AH (29 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_29_AL (29 | BP_ACTIVE_LOW)
-+#define BP_GPIO_30_AH (30 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_30_AL (30 | BP_ACTIVE_LOW)
-+#define BP_GPIO_31_AH (31 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_31_AL (31 | BP_ACTIVE_LOW)
-+#define BP_GPIO_32_AH (32 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_32_AL (32 | BP_ACTIVE_LOW)
-+#define BP_GPIO_33_AH (33 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_33_AL (33 | BP_ACTIVE_LOW)
-+#define BP_GPIO_34_AH (34 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_34_AL (34 | BP_ACTIVE_LOW)
-+#define BP_GPIO_35_AH (35 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_35_AL (35 | BP_ACTIVE_LOW)
-+#define BP_GPIO_36_AH (36 | BP_ACTIVE_HIGH)
-+#define BP_GPIO_36_AL (36 | BP_ACTIVE_LOW)
-+
-+/* Values for external interrupt assignments. */
-+#define BP_EXT_INTR_0 0
-+#define BP_EXT_INTR_1 1
-+#define BP_EXT_INTR_2 2
-+#define BP_EXT_INTR_3 3
-+
-+/* Values for chip select assignments. */
-+#define BP_CS_0 0
-+#define BP_CS_1 1
-+#define BP_CS_2 2
-+#define BP_CS_3 3
-+
-+/* Value for GPIO and external interrupt fields that are not used. */
-+#define BP_NOT_DEFINED 0xffff
-+#define BP_HW_DEFINED 0xfff0
-+#define BP_UNEQUIPPED 0xfff1
-+
-+/* Maximum size of the board id string. */
-+#define BP_BOARD_ID_LEN 16
-+
-+/* Maximum number of Ethernet MACs. */
-+#define BP_MAX_ENET_MACS 2
-+
-+/* Maximum number of VoIP DSPs. */
-+#define BP_MAX_VOIP_DSP 2
-+
-+/* Wireless Antenna Settings. */
-+#define BP_WLAN_ANT_MAIN 0
-+#define BP_WLAN_ANT_AUX 1
-+#define BP_WLAN_ANT_BOTH 3
-+
-+#if !defined(__ASSEMBLER__)
-+
-+/* Information about an Ethernet MAC. If ucPhyType is BP_ENET_NO_PHY,
-+ * then the other fields are not valid.
-+ */
-+typedef struct EthernetMacInfo
-+{
-+ unsigned char ucPhyType; /* BP_ENET_xxx */
-+ unsigned char ucPhyAddress; /* 0 to 31 */
-+ unsigned short usGpioPhySpiSck; /* GPIO pin or not defined */
-+ unsigned short usGpioPhySpiSs; /* GPIO pin or not defined */
-+ unsigned short usGpioPhySpiMosi; /* GPIO pin or not defined */
-+ unsigned short usGpioPhySpiMiso; /* GPIO pin or not defined */
-+ unsigned short usGpioPhyReset; /* GPIO pin or not defined (96348LV) */
-+ unsigned short numSwitchPorts; /* Number of PHY ports */
-+ unsigned short usConfigType; /* Configuration type */
-+ unsigned short usReverseMii; /* Reverse MII */
-+} ETHERNET_MAC_INFO, *PETHERNET_MAC_INFO;
-+
-+
-+/* Information about VoIP DSPs. If ucDspType is BP_VOIP_NO_DSP,
-+ * then the other fields are not valid.
-+ */
-+typedef struct VoIPDspInfo
-+{
-+ unsigned char ucDspType;
-+ unsigned char ucDspAddress;
-+ unsigned short usExtIntrVoip;
-+ unsigned short usGpioVoipReset;
-+ unsigned short usGpioVoipIntr;
-+ unsigned short usGpioLedVoip;
-+ unsigned short usCsVoip;
-+
-+} VOIP_DSP_INFO;
-+
-+
-+/**************************************************************************
-+ * Name : BpSetBoardId
-+ *
-+ * Description: This function find the BOARD_PARAMETERS structure for the
-+ * specified board id string and assigns it to a global, static
-+ * variable.
-+ *
-+ * Parameters : [IN] pszBoardId - Board id string that is saved into NVRAM.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_FOUND - Error, board id input string does not
-+ * have a board parameters configuration record.
-+ ***************************************************************************/
-+int BpSetBoardId( char *pszBoardId );
-+
-+/**************************************************************************
-+ * Name : BpGetBoardIds
-+ *
-+ * Description: This function returns all of the supported board id strings.
-+ *
-+ * Parameters : [OUT] pszBoardIds - Address of a buffer that the board id
-+ * strings are returned in. Each id starts at BP_BOARD_ID_LEN
-+ * boundary.
-+ * [IN] nBoardIdsSize - Number of BP_BOARD_ID_LEN elements that
-+ * were allocated in pszBoardIds.
-+ *
-+ * Returns : Number of board id strings returned.
-+ ***************************************************************************/
-+int BpGetBoardIds( char *pszBoardIds, int nBoardIdsSize );
-+
-+/**************************************************************************
-+ * Name : BpGetEthernetMacInfo
-+ *
-+ * Description: This function returns all of the supported board id strings.
-+ *
-+ * Parameters : [OUT] pEnetInfos - Address of an array of ETHERNET_MAC_INFO
-+ * buffers.
-+ * [IN] nNumEnetInfos - Number of ETHERNET_MAC_INFO elements that
-+ * are pointed to by pEnetInfos.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ ***************************************************************************/
-+int BpGetEthernetMacInfo( PETHERNET_MAC_INFO pEnetInfos, int nNumEnetInfos );
-+
-+/**************************************************************************
-+ * Name : BpGetSdramSize
-+ *
-+ * Description: This function returns a constant that describees the board's
-+ * SDRAM type and size.
-+ *
-+ * Parameters : [OUT] pulSdramSize - Address of short word that the SDRAM size
-+ * is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ ***************************************************************************/
-+int BpGetSdramSize( unsigned long *pulSdramSize );
-+
-+/**************************************************************************
-+ * Name : BpGetPsiSize
-+ *
-+ * Description: This function returns the persistent storage size in K bytes.
-+ *
-+ * Parameters : [OUT] pulPsiSize - Address of short word that the persistent
-+ * storage size is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ ***************************************************************************/
-+int BpGetPsiSize( unsigned long *pulPsiSize );
-+
-+/**************************************************************************
-+ * Name : BpGetRj11InnerOuterPairGpios
-+ *
-+ * Description: This function returns the GPIO pin assignments for changing
-+ * between the RJ11 inner pair and RJ11 outer pair.
-+ *
-+ * Parameters : [OUT] pusInner - Address of short word that the RJ11 inner pair
-+ * GPIO pin is returned in.
-+ * [OUT] pusOuter - Address of short word that the RJ11 outer pair
-+ * GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, values are returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetRj11InnerOuterPairGpios( unsigned short *pusInner,
-+ unsigned short *pusOuter );
-+
-+/**************************************************************************
-+ * Name : BpGetPressAndHoldResetGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the press
-+ * and hold reset button.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the press and hold
-+ * reset button GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetPressAndHoldResetGpio( unsigned short *pusValue );
-+
-+/**************************************************************************
-+ * Name : BpGetVoipResetGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the VOIP
-+ * Reset operation.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the VOIP reset
-+ * GPIO pin is returned in.
-+ * [IN] dspNum - Address of the DSP to query.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetVoipResetGpio( unsigned char dspNum, unsigned short *pusValue );
-+
-+/**************************************************************************
-+ * Name : BpGetVoipIntrGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for VoIP interrupt.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the VOIP interrupt
-+ * GPIO pin is returned in.
-+ * [IN] dspNum - Address of the DSP to query.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetVoipIntrGpio( unsigned char dspNum, unsigned short *pusValue );
-+
-+/**************************************************************************
-+ * Name : BpGetPcmciaResetGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the PCMCIA
-+ * Reset operation.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the PCMCIA reset
-+ * GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetPcmciaResetGpio( unsigned short *pusValue );
-+
-+/**************************************************************************
-+ * Name : BpGetUartRtsCtsGpios
-+ *
-+ * Description: This function returns the GPIO pin assignments for RTS and CTS
-+ * UART signals.
-+ *
-+ * Parameters : [OUT] pusRts - Address of short word that the UART RTS GPIO
-+ * pin is returned in.
-+ * [OUT] pusCts - Address of short word that the UART CTS GPIO
-+ * pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, values are returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetRtsCtsUartGpios( unsigned short *pusRts, unsigned short *pusCts );
-+
-+/**************************************************************************
-+ * Name : BpGetAdslLedGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the ADSL
-+ * LED.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the ADSL LED
-+ * GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetAdslLedGpio( unsigned short *pusValue );
-+
-+/**************************************************************************
-+ * Name : BpGetAdslFailLedGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the ADSL
-+ * LED that is used when there is a DSL connection failure.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the ADSL LED
-+ * GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetAdslFailLedGpio( unsigned short *pusValue );
-+
-+/**************************************************************************
-+ * Name : BpGetWirelessLedGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the Wireless
-+ * LED.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the Wireless LED
-+ * GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetWirelessLedGpio( unsigned short *pusValue );
-+
-+/**************************************************************************
-+ * Name : BpGetWirelessAntInUse
-+ *
-+ * Description: This function returns the antennas in use for wireless
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the Wireless Antenna
-+ * is in use.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetWirelessAntInUse( unsigned short *pusValue );
-+
-+/**************************************************************************
-+ * Name : BpGetWirelessSesBtnGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the Wireless
-+ * Ses Button.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the Wireless Ses
-+ * Button GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetWirelessSesBtnGpio( unsigned short *pusValue );
-+
-+/**************************************************************************
-+ * Name : BpGetWirelessSesExtIntr
-+ *
-+ * Description: This function returns the external interrupt number for the
-+ * Wireless Ses Button.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the Wireless Ses
-+ * external interrup is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetWirelessSesExtIntr( unsigned short *pusValue );
-+
-+/**************************************************************************
-+ * Name : BpGetWirelessSesLedGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the Wireless
-+ * Ses Led.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the Wireless Ses
-+ * Led GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetWirelessSesLedGpio( unsigned short *pusValue );
-+
-+/**************************************************************************
-+ * Name : BpGetUsbLedGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the USB
-+ * LED.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the USB LED
-+ * GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetUsbLedGpio( unsigned short *pusValue );
-+
-+/**************************************************************************
-+ * Name : BpGetHpnaLedGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the HPNA
-+ * LED.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the HPNA LED
-+ * GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetHpnaLedGpio( unsigned short *pusValue );
-+
-+/**************************************************************************
-+ * Name : BpGetWanDataLedGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the WAN Data
-+ * LED.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the WAN Data LED
-+ * GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetWanDataLedGpio( unsigned short *pusValue );
-+
-+/**************************************************************************
-+ * Name : BpGetPppLedGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the PPP
-+ * LED.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the PPP LED
-+ * GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetPppLedGpio( unsigned short *pusValue );
-+
-+/**************************************************************************
-+ * Name : BpGetPppFailLedGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the PPP
-+ * LED that is used when there is a PPP connection failure.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the PPP LED
-+ * GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetPppFailLedGpio( unsigned short *pusValue );
-+
-+/**************************************************************************
-+ * Name : BpGetVoipLedGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the VOIP
-+ * LED.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the VOIP LED
-+ * GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetVoipLedGpio( unsigned short *pusValue );
-+
-+/**************************************************************************
-+ * Name : BpGetBootloaderPowerOnLedGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the power
-+ * on LED that is set by the bootloader.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the alarm LED
-+ * GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetBootloaderPowerOnLedGpio( unsigned short *pusValue );
-+
-+/**************************************************************************
-+ * Name : BpGetBootloaderAlarmLedGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the alarm
-+ * LED that is set by the bootloader.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the alarm LED
-+ * GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetBootloaderAlarmLedGpio( unsigned short *pusValue );
-+
-+/**************************************************************************
-+ * Name : BpGetBootloaderResetCfgLedGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the reset
-+ * configuration LED that is set by the bootloader.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the reset
-+ * configuration LED GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetBootloaderResetCfgLedGpio( unsigned short *pusValue );
-+
-+/**************************************************************************
-+ * Name : BpGetBootloaderStopLedGpio
-+ *
-+ * Description: This function returns the GPIO pin assignment for the break
-+ * into bootloader LED that is set by the bootloader.
-+ *
-+ * Parameters : [OUT] pusValue - Address of short word that the break into
-+ * bootloader LED GPIO pin is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetBootloaderStopLedGpio( unsigned short *pusValue );
-+
-+/**************************************************************************
-+ * Name : BpGetWirelessExtIntr
-+ *
-+ * Description: This function returns the Wireless external interrupt number.
-+ *
-+ * Parameters : [OUT] pulValue - Address of short word that the wireless
-+ * external interrupt number is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetWirelessExtIntr( unsigned long *pulValue );
-+
-+/**************************************************************************
-+ * Name : BpGetAdslDyingGaspExtIntr
-+ *
-+ * Description: This function returns the ADSL Dying Gasp external interrupt
-+ * number.
-+ *
-+ * Parameters : [OUT] pulValue - Address of short word that the ADSL Dying Gasp
-+ * external interrupt number is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetAdslDyingGaspExtIntr( unsigned long *pulValue );
-+
-+/**************************************************************************
-+ * Name : BpGetVoipExtIntr
-+ *
-+ * Description: This function returns the VOIP external interrupt number.
-+ *
-+ * Parameters : [OUT] pulValue - Address of short word that the VOIP
-+ * external interrupt number is returned in.
-+ * [IN] dspNum - Address of the DSP to query.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetVoipExtIntr( unsigned char dspNum, unsigned long *pulValue );
-+
-+/**************************************************************************
-+ * Name : BpGetHpnaExtIntr
-+ *
-+ * Description: This function returns the HPNA external interrupt number.
-+ *
-+ * Parameters : [OUT] pulValue - Address of short word that the HPNA
-+ * external interrupt number is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetHpnaExtIntr( unsigned long *pulValue );
-+
-+/**************************************************************************
-+ * Name : BpGetHpnaChipSelect
-+ *
-+ * Description: This function returns the HPNA chip select number.
-+ *
-+ * Parameters : [OUT] pulValue - Address of short word that the HPNA
-+ * chip select number is returned in.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetHpnaChipSelect( unsigned long *pulValue );
-+
-+/**************************************************************************
-+ * Name : BpGetVoipChipSelect
-+ *
-+ * Description: This function returns the VOIP chip select number.
-+ *
-+ * Parameters : [OUT] pulValue - Address of short word that the VOIP
-+ * chip select number is returned in.
-+ * [IN] dspNum - Address of the DSP to query.
-+ *
-+ * Returns : BP_SUCCESS - Success, value is returned.
-+ * BP_BOARD_ID_NOT_SET - Error, BpSetBoardId has not been called.
-+ * BP_VALUE_NOT_DEFINED - At least one return value is not defined
-+ * for the board.
-+ ***************************************************************************/
-+int BpGetVoipChipSelect( unsigned char dspNum, unsigned long *pulValue );
-+
-+#endif /* __ASSEMBLER__ */
-+
-+#endif /* _BOARDPARMS_H */
-+
-diff -urN linux-2.6.19/arch/mips/bcm963xx/include/6338_intr.h linux-2.6.19.new/arch/mips/bcm963xx/include/6338_intr.h
---- linux-2.6.19/arch/mips/bcm963xx/include/6338_intr.h 1970-01-01 01:00:00.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/bcm963xx/include/6338_intr.h 2006-12-16 18:46:31.000000000 +0100
-@@ -0,0 +1,64 @@
-+/*
-+<:copyright-gpl
-+ Copyright 2003 Broadcom Corp. All Rights Reserved.
-+
-+ This program is free software; you can distribute it and/or modify it
-+ under the terms of the GNU General Public License (Version 2) as
-+ published by the Free Software Foundation.
-+
-+ This program is distributed in the hope it will be useful, but WITHOUT
-+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-+ for more details.
-+
-+ You should have received a copy of the GNU General Public License along
-+ with this program; if not, write to the Free Software Foundation, Inc.,
-+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-+:>
-+*/
-+
-+#ifndef __6338_INTR_H
-+#define __6338_INTR_H
-+
-+/*=====================================================================*/
-+/* BCM6338 External Interrupt Level Assignments */
-+/*=====================================================================*/
-+#define INTERRUPT_ID_EXTERNAL_0 3
-+#define INTERRUPT_ID_EXTERNAL_1 4
-+#define INTERRUPT_ID_EXTERNAL_2 5
-+#define INTERRUPT_ID_EXTERNAL_3 6
-+
-+/*=====================================================================*/
-+/* BCM6338 Timer Interrupt Level Assignments */
-+/*=====================================================================*/
-+#define MIPS_TIMER_INT 7
-+
-+/*=====================================================================*/
-+/* Peripheral ISR Table Offset */
-+/*=====================================================================*/
-+#define INTERNAL_ISR_TABLE_OFFSET 8
-+
-+/*=====================================================================*/
-+/* Logical Peripheral Interrupt IDs */
-+/*=====================================================================*/
-+
-+#define INTERRUPT_ID_TIMER (INTERNAL_ISR_TABLE_OFFSET + 0)
-+#define INTERRUPT_ID_SPI (INTERNAL_ISR_TABLE_OFFSET + 1)
-+#define INTERRUPT_ID_UART (INTERNAL_ISR_TABLE_OFFSET + 2)
-+#define INTERRUPT_ID_DG (INTERNAL_ISR_TABLE_OFFSET + 4)
-+#define INTERRUPT_ID_ADSL (INTERNAL_ISR_TABLE_OFFSET + 5)
-+#define INTERRUPT_ID_ATM (INTERNAL_ISR_TABLE_OFFSET + 6)
-+#define INTERRUPT_ID_USBS (INTERNAL_ISR_TABLE_OFFSET + 7)
-+#define INTERRUPT_ID_EMAC1 (INTERNAL_ISR_TABLE_OFFSET + 8)
-+#define INTERRUPT_ID_EPHY (INTERNAL_ISR_TABLE_OFFSET + 9)
-+#define INTERRUPT_ID_SDRAM (INTERNAL_ISR_TABLE_OFFSET + 10)
-+#define INTERRUPT_ID_USB_CNTL_RX_DMA (INTERNAL_ISR_TABLE_OFFSET + 11)
-+#define INTERRUPT_ID_USB_CNTL_TX_DMA (INTERNAL_ISR_TABLE_OFFSET + 12)
-+#define INTERRUPT_ID_USB_BULK_RX_DMA (INTERNAL_ISR_TABLE_OFFSET + 13)
-+#define INTERRUPT_ID_USB_BULK_TX_DMA (INTERNAL_ISR_TABLE_OFFSET + 14)
-+#define INTERRUPT_ID_EMAC1_RX_DMA (INTERNAL_ISR_TABLE_OFFSET + 15)
-+#define INTERRUPT_ID_EMAC1_TX_DMA (INTERNAL_ISR_TABLE_OFFSET + 16)
-+#define INTERRUPT_ID_SDIO (INTERNAL_ISR_TABLE_OFFSET + 17)
-+
-+#endif /* __BCM6338_H */
-+
-diff -urN linux-2.6.19/arch/mips/bcm963xx/include/6338_map_part.h linux-2.6.19.new/arch/mips/bcm963xx/include/6338_map_part.h
---- linux-2.6.19/arch/mips/bcm963xx/include/6338_map_part.h 1970-01-01 01:00:00.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/bcm963xx/include/6338_map_part.h 2006-12-16 18:46:31.000000000 +0100
-@@ -0,0 +1,334 @@
-+/*
-+<:copyright-gpl
-+ Copyright 2004 Broadcom Corp. All Rights Reserved.
-+
-+ This program is free software; you can distribute it and/or modify it
-+ under the terms of the GNU General Public License (Version 2) as
-+ published by the Free Software Foundation.
-+
-+ This program is distributed in the hope it will be useful, but WITHOUT
-+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-+ for more details.
-+
-+ You should have received a copy of the GNU General Public License along
-+ with this program; if not, write to the Free Software Foundation, Inc.,
-+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-+:>
-+*/
-+
-+#ifndef __BCM6338_MAP_H
-+#define __BCM6338_MAP_H
-+
-+#include "bcmtypes.h"
-+
-+#define PERF_BASE 0xfffe0000
-+#define TIMR_BASE 0xfffe0200
-+#define UART_BASE 0xfffe0300
-+#define GPIO_BASE 0xfffe0400
-+#define SPI_BASE 0xfffe0c00
-+
-+typedef struct PerfControl {
-+ uint32 RevID;
-+ uint16 testControl;
-+ uint16 blkEnables;
-+#define EMAC_CLK_EN 0x0010
-+#define USBS_CLK_EN 0x0010
-+#define SAR_CLK_EN 0x0020
-+
-+#define SPI_CLK_EN 0x0200
-+
-+ uint32 pll_control;
-+#define SOFT_RESET 0x00000001
-+
-+ uint32 IrqMask;
-+ uint32 IrqStatus;
-+
-+ uint32 ExtIrqCfg;
-+#define EI_SENSE_SHFT 0
-+#define EI_STATUS_SHFT 5
-+#define EI_CLEAR_SHFT 10
-+#define EI_MASK_SHFT 15
-+#define EI_INSENS_SHFT 20
-+#define EI_LEVEL_SHFT 25
-+
-+ uint32 unused[4]; /* (18) */
-+ uint32 BlockSoftReset; /* (28) */
-+#define BSR_SPI 0x00000001
-+#define BSR_EMAC 0x00000004
-+#define BSR_USBH 0x00000008
-+#define BSR_USBS 0x00000010
-+#define BSR_ADSL 0x00000020
-+#define BSR_DMAMEM 0x00000040
-+#define BSR_SAR 0x00000080
-+#define BSR_ACLC 0x00000100
-+#define BSR_ADSL_MIPS_PLL 0x00000400
-+#define BSR_ALL_BLOCKS \
-+ (BSR_SPI | BSR_EMAC | BSR_USBH | BSR_USBS | BSR_ADSL | BSR_DMAMEM | \
-+ BSR_SAR | BSR_ACLC | BSR_ADSL_MIPS_PLL)
-+} PerfControl;
-+
-+#define PERF ((volatile PerfControl * const) PERF_BASE)
-+
-+
-+typedef struct Timer {
-+ uint16 unused0;
-+ byte TimerMask;
-+#define TIMER0EN 0x01
-+#define TIMER1EN 0x02
-+#define TIMER2EN 0x04
-+ byte TimerInts;
-+#define TIMER0 0x01
-+#define TIMER1 0x02
-+#define TIMER2 0x04
-+#define WATCHDOG 0x08
-+ uint32 TimerCtl0;
-+ uint32 TimerCtl1;
-+ uint32 TimerCtl2;
-+#define TIMERENABLE 0x80000000
-+#define RSTCNTCLR 0x40000000
-+ uint32 TimerCnt0;
-+ uint32 TimerCnt1;
-+ uint32 TimerCnt2;
-+ uint32 WatchDogDefCount;
-+
-+ /* Write 0xff00 0x00ff to Start timer
-+ * Write 0xee00 0x00ee to Stop and re-load default count
-+ * Read from this register returns current watch dog count
-+ */
-+ uint32 WatchDogCtl;
-+
-+ /* Number of 40-MHz ticks for WD Reset pulse to last */
-+ uint32 WDResetCount;
-+} Timer;
-+
-+#define TIMER ((volatile Timer * const) TIMR_BASE)
-+typedef struct UartChannel {
-+ byte unused0;
-+ byte control;
-+#define BRGEN 0x80 /* Control register bit defs */
-+#define TXEN 0x40
-+#define RXEN 0x20
-+#define LOOPBK 0x10
-+#define TXPARITYEN 0x08
-+#define TXPARITYEVEN 0x04
-+#define RXPARITYEN 0x02
-+#define RXPARITYEVEN 0x01
-+
-+ byte config;
-+#define XMITBREAK 0x40
-+#define BITS5SYM 0x00
-+#define BITS6SYM 0x10
-+#define BITS7SYM 0x20
-+#define BITS8SYM 0x30
-+#define ONESTOP 0x07
-+#define TWOSTOP 0x0f
-+ /* 4-LSBS represent STOP bits/char
-+ * in 1/8 bit-time intervals. Zero
-+ * represents 1/8 stop bit interval.
-+ * Fifteen represents 2 stop bits.
-+ */
-+ byte fifoctl;
-+#define RSTTXFIFOS 0x80
-+#define RSTRXFIFOS 0x40
-+ /* 5-bit TimeoutCnt is in low bits of this register.
-+ * This count represents the number of characters
-+ * idle times before setting receive Irq when below threshold
-+ */
-+ uint32 baudword;
-+ /* When divide SysClk/2/(1+baudword) we should get 32*bit-rate
-+ */
-+
-+ byte txf_levl; /* Read-only fifo depth */
-+ byte rxf_levl; /* Read-only fifo depth */
-+ byte fifocfg; /* Upper 4-bits are TxThresh, Lower are
-+ * RxThreshold. Irq can be asserted
-+ * when rx fifo> thresh, txfifo<thresh
-+ */
-+ byte prog_out; /* Set value of DTR (Bit0), RTS (Bit1)
-+ * if these bits are also enabled to GPIO_o
-+ */
-+#define DTREN 0x01
-+#define RTSEN 0x02
-+
-+ byte unused1;
-+ byte DeltaIPEdgeNoSense; /* Low 4-bits, set corr bit to 1 to
-+ * detect irq on rising AND falling
-+ * edges for corresponding GPIO_i
-+ * if enabled (edge insensitive)
-+ */
-+ byte DeltaIPConfig_Mask; /* Upper 4 bits: 1 for posedge sense
-+ * 0 for negedge sense if
-+ * not configured for edge
-+ * insensitive (see above)
-+ * Lower 4 bits: Mask to enable change
-+ * detection IRQ for corresponding
-+ * GPIO_i
-+ */
-+ byte DeltaIP_SyncIP; /* Upper 4 bits show which bits
-+ * have changed (may set IRQ).
-+ * read automatically clears bit
-+ * Lower 4 bits are actual status
-+ */
-+
-+ uint16 intMask; /* Same Bit defs for Mask and status */
-+ uint16 intStatus;
-+#define DELTAIP 0x0001
-+#define TXUNDERR 0x0002
-+#define TXOVFERR 0x0004
-+#define TXFIFOTHOLD 0x0008
-+#define TXREADLATCH 0x0010
-+#define TXFIFOEMT 0x0020
-+#define RXUNDERR 0x0040
-+#define RXOVFERR 0x0080
-+#define RXTIMEOUT 0x0100
-+#define RXFIFOFULL 0x0200
-+#define RXFIFOTHOLD 0x0400
-+#define RXFIFONE 0x0800
-+#define RXFRAMERR 0x1000
-+#define RXPARERR 0x2000
-+#define RXBRK 0x4000
-+
-+ uint16 unused2;
-+ uint16 Data; /* Write to TX, Read from RX */
-+ /* bits 11:8 are BRK,PAR,FRM errors */
-+
-+ uint32 unused3;
-+ uint32 unused4;
-+} Uart;
-+
-+#define UART ((volatile Uart * const) UART_BASE)
-+
-+typedef struct GpioControl {
-+ uint32 unused0;
-+ uint32 GPIODir; /* bits 7:0 */
-+ uint32 unused1;
-+ uint32 GPIOio; /* bits 7:0 */
-+ uint32 LEDCtrl;
-+#define LED3_STROBE 0x08000000
-+#define LED2_STROBE 0x04000000
-+#define LED1_STROBE 0x02000000
-+#define LED0_STROBE 0x01000000
-+#define LED_TEST 0x00010000
-+#define LED3_DISABLE_LINK_ACT 0x00008000
-+#define LED2_DISABLE_LINK_ACT 0x00004000
-+#define LED1_DISABLE_LINK_ACT 0x00002000
-+#define LED0_DISABLE_LINK_ACT 0x00001000
-+#define LED_INTERVAL_SET_MASK 0x00000f00
-+#define LED_INTERVAL_SET_320MS 0x00000500
-+#define LED_INTERVAL_SET_160MS 0x00000400
-+#define LED_INTERVAL_SET_80MS 0x00000300
-+#define LED_INTERVAL_SET_40MS 0x00000200
-+#define LED_INTERVAL_SET_20MS 0x00000100
-+#define LED3_ON 0x00000080
-+#define LED2_ON 0x00000040
-+#define LED1_ON 0x00000020
-+#define LED0_ON 0x00000010
-+#define LED3_ENABLE 0x00000008
-+#define LED2_ENABLE 0x00000004
-+#define LED1_ENABLE 0x00000002
-+#define LED0_ENABLE 0x00000001
-+ uint32 SpiSlaveCfg;
-+#define SPI_SLAVE_RESET 0x00010000
-+#define SPI_RESTRICT 0x00000400
-+#define SPI_DELAY_DISABLE 0x00000200
-+#define SPI_PROBE_MUX_SEL_MASK 0x000001e0
-+#define SPI_SER_ADDR_CFG_MASK 0x0000000c
-+#define SPI_MODE 0x00000001
-+ uint32 vRegConfig;
-+} GpioControl;
-+
-+#define GPIO ((volatile GpioControl * const) GPIO_BASE)
-+
-+/* Number to mask conversion macro used for GPIODir and GPIOio */
-+#define GPIO_NUM_MAX_BITS_MASK 0x0f
-+#define GPIO_NUM_TO_MASK(X) (1 << ((X) & GPIO_NUM_MAX_BITS_MASK))
-+
-+/*
-+** Spi Controller
-+*/
-+
-+typedef struct SpiControl {
-+ uint16 spiCmd; /* (0x0): SPI command */
-+#define SPI_CMD_START_IMMEDIATE 3
-+
-+#define SPI_CMD_COMMAND_SHIFT 0
-+#define SPI_CMD_DEVICE_ID_SHIFT 4
-+#define SPI_CMD_PREPEND_BYTE_CNT_SHIFT 8
-+
-+ byte spiIntStatus; /* (0x2): SPI interrupt status */
-+ byte spiMaskIntStatus; /* (0x3): SPI masked interrupt status */
-+
-+ byte spiIntMask; /* (0x4): SPI interrupt mask */
-+#define SPI_INTR_CMD_DONE 0x01
-+#define SPI_INTR_CLEAR_ALL 0x1f
-+
-+ byte spiStatus; /* (0x5): SPI status */
-+
-+ byte spiClkCfg; /* (0x6): SPI clock configuration */
-+
-+ byte spiFillByte; /* (0x7): SPI fill byte */
-+
-+ byte unused0;
-+ byte spiMsgTail; /* (0x9): msgtail */
-+ byte unused1;
-+ byte spiRxTail; /* (0xB): rxtail */
-+
-+ uint32 unused2[13]; /* (0x0c - 0x3c) reserved */
-+
-+ byte spiMsgCtl; /* (0x40) control byte */
-+#define HALF_DUPLEX_W 1
-+#define HALF_DUPLEX_R 2
-+#define SPI_MSG_TYPE_SHIFT 6
-+#define SPI_BYTE_CNT_SHIFT 0
-+ byte spiMsgData[63]; /* (0x41 - 0x7f) msg data */
-+ byte spiRxDataFifo[64]; /* (0x80 - 0xbf) rx data */
-+ byte unused3[64]; /* (0xc0 - 0xff) reserved */
-+} SpiControl;
-+
-+#define SPI ((volatile SpiControl * const) SPI_BASE)
-+
-+/*
-+** External Bus Interface
-+*/
-+typedef struct EbiChipSelect {
-+ uint32 base; /* base address in upper 24 bits */
-+#define EBI_SIZE_8K 0
-+#define EBI_SIZE_16K 1
-+#define EBI_SIZE_32K 2
-+#define EBI_SIZE_64K 3
-+#define EBI_SIZE_128K 4
-+#define EBI_SIZE_256K 5
-+#define EBI_SIZE_512K 6
-+#define EBI_SIZE_1M 7
-+#define EBI_SIZE_2M 8
-+#define EBI_SIZE_4M 9
-+#define EBI_SIZE_8M 10
-+#define EBI_SIZE_16M 11
-+#define EBI_SIZE_32M 12
-+#define EBI_SIZE_64M 13
-+#define EBI_SIZE_128M 14
-+#define EBI_SIZE_256M 15
-+ uint32 config;
-+#define EBI_ENABLE 0x00000001 /* .. enable this range */
-+#define EBI_WAIT_STATES 0x0000000e /* .. mask for wait states */
-+#define EBI_WTST_SHIFT 1 /* .. for shifting wait states */
-+#define EBI_WORD_WIDE 0x00000010 /* .. 16-bit peripheral, else 8 */
-+#define EBI_WREN 0x00000020 /* enable posted writes */
-+#define EBI_POLARITY 0x00000040 /* .. set to invert something,
-+ ** don't know what yet */
-+#define EBI_TS_TA_MODE 0x00000080 /* .. use TS/TA mode */
-+#define EBI_TS_SEL 0x00000100 /* .. drive tsize, not bs_b */
-+#define EBI_FIFO 0x00000200 /* .. use fifo */
-+#define EBI_RE 0x00000400 /* .. Reverse Endian */
-+} EbiChipSelect;
-+
-+typedef struct MpiRegisters {
-+ EbiChipSelect cs[1]; /* size chip select configuration */
-+} MpiRegisters;
-+
-+#define MPI ((volatile MpiRegisters * const) MPI_BASE)
-+
-+
-+#endif
-+
-diff -urN linux-2.6.19/arch/mips/bcm963xx/include/6345_intr.h linux-2.6.19.new/arch/mips/bcm963xx/include/6345_intr.h
---- linux-2.6.19/arch/mips/bcm963xx/include/6345_intr.h 1970-01-01 01:00:00.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/bcm963xx/include/6345_intr.h 2006-12-16 18:46:31.000000000 +0100
-@@ -0,0 +1,72 @@
-+/*
-+<:copyright-gpl
-+ Copyright 2002 Broadcom Corp. All Rights Reserved.
-+
-+ This program is free software; you can distribute it and/or modify it
-+ under the terms of the GNU General Public License (Version 2) as
-+ published by the Free Software Foundation.
-+
-+ This program is distributed in the hope it will be useful, but WITHOUT
-+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-+ for more details.
-+
-+ You should have received a copy of the GNU General Public License along
-+ with this program; if not, write to the Free Software Foundation, Inc.,
-+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-+:>
-+*/
-+
-+#ifndef __6345_INTR_H
-+#define __6345_INTR_H
-+
-+
-+/*=====================================================================*/
-+/* BCM6345 External Interrupt Level Assignments */
-+/*=====================================================================*/
-+#define INTERRUPT_ID_EXTERNAL_0 3
-+#define INTERRUPT_ID_EXTERNAL_1 4
-+#define INTERRUPT_ID_EXTERNAL_2 5
-+#define INTERRUPT_ID_EXTERNAL_3 6
-+
-+/*=====================================================================*/
-+/* BCM6345 Timer Interrupt Level Assignments */
-+/*=====================================================================*/
-+#define MIPS_TIMER_INT 7
-+
-+/*=====================================================================*/
-+/* Peripheral ISR Table Offset */
-+/*=====================================================================*/
-+#define INTERNAL_ISR_TABLE_OFFSET 8
-+#define DMA_ISR_TABLE_OFFSET (INTERNAL_ISR_TABLE_OFFSET + 13)
-+
-+/*=====================================================================*/
-+/* Logical Peripheral Interrupt IDs */
-+/*=====================================================================*/
-+
-+/* Internal peripheral interrupt IDs */
-+#define INTERRUPT_ID_TIMER (INTERNAL_ISR_TABLE_OFFSET + 0)
-+#define INTERRUPT_ID_UART (INTERNAL_ISR_TABLE_OFFSET + 2)
-+#define INTERRUPT_ID_ADSL (INTERNAL_ISR_TABLE_OFFSET + 3)
-+#define INTERRUPT_ID_ATM (INTERNAL_ISR_TABLE_OFFSET + 4)
-+#define INTERRUPT_ID_USB (INTERNAL_ISR_TABLE_OFFSET + 5)
-+#define INTERRUPT_ID_EMAC (INTERNAL_ISR_TABLE_OFFSET + 8)
-+#define INTERRUPT_ID_EPHY (INTERNAL_ISR_TABLE_OFFSET + 12)
-+
-+/* DMA channel interrupt IDs */
-+#define INTERRUPT_ID_EMAC_RX_CHAN (DMA_ISR_TABLE_OFFSET + EMAC_RX_CHAN)
-+#define INTERRUPT_ID_EMAC_TX_CHAN (DMA_ISR_TABLE_OFFSET + EMAC_TX_CHAN)
-+#define INTERRUPT_ID_EBI_RX_CHAN (DMA_ISR_TABLE_OFFSET + EBI_RX_CHAN)
-+#define INTERRUPT_ID_EBI_TX_CHAN (DMA_ISR_TABLE_OFFSET + EBI_TX_CHAN)
-+#define INTERRUPT_ID_RESERVED_RX_CHAN (DMA_ISR_TABLE_OFFSET + RESERVED_RX_CHAN)
-+#define INTERRUPT_ID_RESERVED_TX_CHAN (DMA_ISR_TABLE_OFFSET + RESERVED_TX_CHAN)
-+#define INTERRUPT_ID_USB_BULK_RX_CHAN (DMA_ISR_TABLE_OFFSET + USB_BULK_RX_CHAN)
-+#define INTERRUPT_ID_USB_BULK_TX_CHAN (DMA_ISR_TABLE_OFFSET + USB_BULK_TX_CHAN)
-+#define INTERRUPT_ID_USB_CNTL_RX_CHAN (DMA_ISR_TABLE_OFFSET + USB_CNTL_RX_CHAN)
-+#define INTERRUPT_ID_USB_CNTL_TX_CHAN (DMA_ISR_TABLE_OFFSET + USB_CNTL_TX_CHAN)
-+#define INTERRUPT_ID_USB_ISO_RX_CHAN (DMA_ISR_TABLE_OFFSET + USB_ISO_RX_CHAN)
-+#define INTERRUPT_ID_USB_ISO_TX_CHAN (DMA_ISR_TABLE_OFFSET + USB_ISO_TX_CHAN)
-+
-+
-+#endif /* __BCM6345_H */
-+
-diff -urN linux-2.6.19/arch/mips/bcm963xx/include/6345_map_part.h linux-2.6.19.new/arch/mips/bcm963xx/include/6345_map_part.h
---- linux-2.6.19/arch/mips/bcm963xx/include/6345_map_part.h 1970-01-01 01:00:00.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/bcm963xx/include/6345_map_part.h 2006-12-16 18:46:31.000000000 +0100
-@@ -0,0 +1,163 @@
-+/*
-+<:copyright-gpl
-+ Copyright 2002 Broadcom Corp. All Rights Reserved.
-+
-+ This program is free software; you can distribute it and/or modify it
-+ under the terms of the GNU General Public License (Version 2) as
-+ published by the Free Software Foundation.
-+
-+ This program is distributed in the hope it will be useful, but WITHOUT
-+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-+ for more details.
-+
-+ You should have received a copy of the GNU General Public License along
-+ with this program; if not, write to the Free Software Foundation, Inc.,
-+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-+:>
-+*/
-+
-+#ifndef __BCM6345_MAP_H
-+#define __BCM6345_MAP_H
-+
-+
-+#include "bcmtypes.h"
-+#include "6345_intr.h"
-+
-+typedef struct IntControl {
-+ uint32 RevID;
-+ uint16 testControl;
-+ uint16 blkEnables;
-+#define USB_CLK_EN 0x0100
-+#define EMAC_CLK_EN 0x0080
-+#define UART_CLK_EN 0x0008
-+#define CPU_CLK_EN 0x0001
-+
-+ uint32 pll_control;
-+#define SOFT_RESET 0x00000001
-+
-+ uint32 IrqMask;
-+ uint32 IrqStatus;
-+
-+ uint32 ExtIrqCfg;
-+#define EI_SENSE_SHFT 0
-+#define EI_STATUS_SHFT 4
-+#define EI_CLEAR_SHFT 8
-+#define EI_MASK_SHFT 12
-+#define EI_INSENS_SHFT 16
-+#define EI_LEVEL_SHFT 20
-+} IntControl;
-+
-+#define INTC_BASE 0xfffe0000
-+#define PERF ((volatile IntControl * const) INTC_BASE)
-+
-+#define TIMR_BASE 0xfffe0200
-+typedef struct Timer {
-+ uint16 unused0;
-+ byte TimerMask;
-+#define TIMER0EN 0x01
-+#define TIMER1EN 0x02
-+#define TIMER2EN 0x04
-+ byte TimerInts;
-+#define TIMER0 0x01
-+#define TIMER1 0x02
-+#define TIMER2 0x04
-+#define WATCHDOG 0x08
-+ uint32 TimerCtl0;
-+ uint32 TimerCtl1;
-+ uint32 TimerCtl2;
-+#define TIMERENABLE 0x80000000
-+#define RSTCNTCLR 0x40000000
-+ uint32 TimerCnt0;
-+ uint32 TimerCnt1;
-+ uint32 TimerCnt2;
-+ uint32 WatchDogDefCount;
-+
-+ /* Write 0xff00 0x00ff to Start timer
-+ * Write 0xee00 0x00ee to Stop and re-load default count
-+ * Read from this register returns current watch dog count
-+ */
-+ uint32 WatchDogCtl;
-+
-+ /* Number of 40-MHz ticks for WD Reset pulse to last */
-+ uint32 WDResetCount;
-+} Timer;
-+
-+#define TIMER ((volatile Timer * const) TIMR_BASE)
-+
-+typedef struct UartChannel {
-+ byte unused0;
-+ byte control;
-+#define BRGEN 0x80 /* Control register bit defs */
-+#define TXEN 0x40
-+#define RXEN 0x20
-+#define TXPARITYEN 0x08
-+#define TXPARITYEVEN 0x04
-+#define RXPARITYEN 0x02
-+#define RXPARITYEVEN 0x01
-+ byte config;
-+#define BITS5SYM 0x00
-+#define BITS6SYM 0x10
-+#define BITS7SYM 0x20
-+#define BITS8SYM 0x30
-+#define XMITBREAK 0x40
-+#define ONESTOP 0x07
-+#define TWOSTOP 0x0f
-+
-+ byte fifoctl;
-+#define RSTTXFIFOS 0x80
-+#define RSTRXFIFOS 0x40
-+ uint32 baudword;
-+
-+ byte txf_levl;
-+ byte rxf_levl;
-+ byte fifocfg;
-+ byte prog_out;
-+
-+ byte unused1;
-+ byte DeltaIPEdgeNoSense;
-+ byte DeltaIPConfig_Mask;
-+ byte DeltaIP_SyncIP;
-+ uint16 intMask;
-+ uint16 intStatus;
-+#define TXUNDERR 0x0002
-+#define TXOVFERR 0x0004
-+#define TXFIFOEMT 0x0020
-+#define RXOVFERR 0x0080
-+#define RXFIFONE 0x0800
-+#define RXFRAMERR 0x1000
-+#define RXPARERR 0x2000
-+#define RXBRK 0x4000
-+
-+ uint16 unused2;
-+ uint16 Data;
-+ uint32 unused3;
-+ uint32 unused4;
-+} Uart;
-+
-+#define UART_BASE 0xfffe0300
-+#define UART ((volatile Uart * const) UART_BASE)
-+
-+typedef struct GpioControl {
-+ uint16 unused0;
-+ byte unused1;
-+ byte TBusSel;
-+
-+ uint16 unused2;
-+ uint16 GPIODir;
-+ byte unused3;
-+ byte Leds;
-+ uint16 GPIOio;
-+
-+ uint32 UartCtl;
-+} GpioControl;
-+
-+#define GPIO_BASE 0xfffe0400
-+#define GPIO ((volatile GpioControl * const) GPIO_BASE)
-+
-+#define GPIO_NUM_MAX_BITS_MASK 0x0f
-+#define GPIO_NUM_TO_MASK(X) (1 << ((X) & GPIO_NUM_MAX_BITS_MASK))
-+
-+
-+#endif
-+
-diff -urN linux-2.6.19/arch/mips/bcm963xx/include/6348_intr.h linux-2.6.19.new/arch/mips/bcm963xx/include/6348_intr.h
---- linux-2.6.19/arch/mips/bcm963xx/include/6348_intr.h 1970-01-01 01:00:00.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/bcm963xx/include/6348_intr.h 2006-12-16 18:46:31.000000000 +0100
-@@ -0,0 +1,74 @@
-+/*
-+<:copyright-gpl
-+ Copyright 2003 Broadcom Corp. All Rights Reserved.
-+
-+ This program is free software; you can distribute it and/or modify it
-+ under the terms of the GNU General Public License (Version 2) as
-+ published by the Free Software Foundation.
-+
-+ This program is distributed in the hope it will be useful, but WITHOUT
-+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-+ for more details.
-+
-+ You should have received a copy of the GNU General Public License along
-+ with this program; if not, write to the Free Software Foundation, Inc.,
-+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-+:>
-+*/
-+
-+#ifndef __6348_INTR_H
-+#define __6348_INTR_H
-+
-+
-+/*=====================================================================*/
-+/* BCM6348 External Interrupt Level Assignments */
-+/*=====================================================================*/
-+#define INTERRUPT_ID_EXTERNAL_0 3
-+#define INTERRUPT_ID_EXTERNAL_1 4
-+#define INTERRUPT_ID_EXTERNAL_2 5
-+#define INTERRUPT_ID_EXTERNAL_3 6
-+
-+/*=====================================================================*/
-+/* BCM6348 Timer Interrupt Level Assignments */
-+/*=====================================================================*/
-+#define MIPS_TIMER_INT 7
-+
-+/*=====================================================================*/
-+/* Peripheral ISR Table Offset */
-+/*=====================================================================*/
-+#define INTERNAL_ISR_TABLE_OFFSET 8
-+
-+/*=====================================================================*/
-+/* Logical Peripheral Interrupt IDs */
-+/*=====================================================================*/
-+
-+#define INTERRUPT_ID_TIMER (INTERNAL_ISR_TABLE_OFFSET + 0)
-+#define INTERRUPT_ID_SPI (INTERNAL_ISR_TABLE_OFFSET + 1)
-+#define INTERRUPT_ID_UART (INTERNAL_ISR_TABLE_OFFSET + 2)
-+#define INTERRUPT_ID_ADSL (INTERNAL_ISR_TABLE_OFFSET + 4)
-+#define INTERRUPT_ID_ATM (INTERNAL_ISR_TABLE_OFFSET + 5)
-+#define INTERRUPT_ID_USBS (INTERNAL_ISR_TABLE_OFFSET + 6)
-+#define INTERRUPT_ID_EMAC2 (INTERNAL_ISR_TABLE_OFFSET + 7)
-+#define INTERRUPT_ID_EMAC1 (INTERNAL_ISR_TABLE_OFFSET + 8)
-+#define INTERRUPT_ID_EPHY (INTERNAL_ISR_TABLE_OFFSET + 9)
-+#define INTERRUPT_ID_M2M (INTERNAL_ISR_TABLE_OFFSET + 10)
-+#define INTERRUPT_ID_ACLC (INTERNAL_ISR_TABLE_OFFSET + 11)
-+#define INTERRUPT_ID_USBH (INTERNAL_ISR_TABLE_OFFSET + 12)
-+#define INTERRUPT_ID_SDRAM (INTERNAL_ISR_TABLE_OFFSET + 13)
-+#define INTERRUPT_ID_USB_CNTL_RX_DMA (INTERNAL_ISR_TABLE_OFFSET + 14)
-+#define INTERRUPT_ID_USB_CNTL_TX_DMA (INTERNAL_ISR_TABLE_OFFSET + 15)
-+#define INTERRUPT_ID_USB_BULK_RX_DMA (INTERNAL_ISR_TABLE_OFFSET + 16)
-+#define INTERRUPT_ID_USB_BULK_TX_DMA (INTERNAL_ISR_TABLE_OFFSET + 17)
-+#define INTERRUPT_ID_USB_ISO_RX_DMA (INTERNAL_ISR_TABLE_OFFSET + 18)
-+#define INTERRUPT_ID_USB_ISO_TX_DMA (INTERNAL_ISR_TABLE_OFFSET + 19)
-+#define INTERRUPT_ID_EMAC1_RX_DMA (INTERNAL_ISR_TABLE_OFFSET + 20)
-+#define INTERRUPT_ID_EMAC1_TX_DMA (INTERNAL_ISR_TABLE_OFFSET + 21)
-+#define INTERRUPT_ID_EMAC2_RX_DMA (INTERNAL_ISR_TABLE_OFFSET + 22)
-+#define INTERRUPT_ID_EMAC2_TX_DMA (INTERNAL_ISR_TABLE_OFFSET + 23)
-+#define INTERRUPT_ID_MPI (INTERNAL_ISR_TABLE_OFFSET + 24)
-+#define INTERRUPT_ID_DG (INTERNAL_ISR_TABLE_OFFSET + 25)
-+
-+
-+#endif /* __BCM6348_H */
-+
-diff -urN linux-2.6.19/arch/mips/bcm963xx/include/6348_map_part.h linux-2.6.19.new/arch/mips/bcm963xx/include/6348_map_part.h
---- linux-2.6.19/arch/mips/bcm963xx/include/6348_map_part.h 1970-01-01 01:00:00.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/bcm963xx/include/6348_map_part.h 2006-12-16 18:46:31.000000000 +0100
-@@ -0,0 +1,500 @@
-+/*
-+<:copyright-gpl
-+ Copyright 2002 Broadcom Corp. All Rights Reserved.
-+
-+ This program is free software; you can distribute it and/or modify it
-+ under the terms of the GNU General Public License (Version 2) as
-+ published by the Free Software Foundation.
-+
-+ This program is distributed in the hope it will be useful, but WITHOUT
-+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-+ for more details.
-+
-+ You should have received a copy of the GNU General Public License along
-+ with this program; if not, write to the Free Software Foundation, Inc.,
-+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-+:>
-+*/
-+
-+#ifndef __BCM6348_MAP_H
-+#define __BCM6348_MAP_H
-+
-+#include "bcmtypes.h"
-+
-+#define PERF_BASE 0xfffe0000
-+#define TIMR_BASE 0xfffe0200
-+#define UART_BASE 0xfffe0300
-+#define GPIO_BASE 0xfffe0400
-+#define MPI_BASE 0xfffe2000 /* MPI control registers */
-+#define USB_HOST_BASE 0xfffe1b00 /* USB host registers */
-+#define USB_HOST_NON_OHCI 0xfffe1c00 /* USB host non-OHCI registers */
-+
-+typedef struct PerfControl {
-+ uint32 RevID;
-+ uint16 testControl;
-+ uint16 blkEnables;
-+#define EMAC_CLK_EN 0x0010
-+#define SAR_CLK_EN 0x0020
-+#define USBS_CLK_EN 0x0040
-+#define USBH_CLK_EN 0x0100
-+
-+ uint32 pll_control;
-+#define SOFT_RESET 0x00000001
-+
-+ uint32 IrqMask;
-+ uint32 IrqStatus;
-+
-+ uint32 ExtIrqCfg;
-+#define EI_SENSE_SHFT 0
-+#define EI_STATUS_SHFT 5
-+#define EI_CLEAR_SHFT 10
-+#define EI_MASK_SHFT 15
-+#define EI_INSENS_SHFT 20
-+#define EI_LEVEL_SHFT 25
-+
-+ uint32 unused[4]; /* (18) */
-+ uint32 BlockSoftReset; /* (28) */
-+#define BSR_SPI 0x00000001
-+#define BSR_EMAC 0x00000004
-+#define BSR_USBH 0x00000008
-+#define BSR_USBS 0x00000010
-+#define BSR_ADSL 0x00000020
-+#define BSR_DMAMEM 0x00000040
-+#define BSR_SAR 0x00000080
-+#define BSR_ACLC 0x00000100
-+#define BSR_ADSL_MIPS_PLL 0x00000400
-+#define BSR_ALL_BLOCKS \
-+ (BSR_SPI | BSR_EMAC | BSR_USBH | BSR_USBS | BSR_ADSL | BSR_DMAMEM | \
-+ BSR_SAR | BSR_ACLC | BSR_ADSL_MIPS_PLL)
-+ uint32 unused2[2]; /* (2c) */
-+ uint32 PllStrap; /* (34) */
-+#define PLL_N1_SHFT 20
-+#define PLL_N1_MASK (7<<PLL_N1_SHFT)
-+#define PLL_N2_SHFT 15
-+#define PLL_N2_MASK (0x1f<<PLL_N2_SHFT)
-+#define PLL_M1_REF_SHFT 12
-+#define PLL_M1_REF_MASK (7<<PLL_M1_REF_SHFT)
-+#define PLL_M2_REF_SHFT 9
-+#define PLL_M2_REF_MASK (7<<PLL_M2_REF_SHFT)
-+#define PLL_M1_CPU_SHFT 6
-+#define PLL_M1_CPU_MASK (7<<PLL_M1_CPU_SHFT)
-+#define PLL_M1_BUS_SHFT 3
-+#define PLL_M1_BUS_MASK (7<<PLL_M1_BUS_SHFT)
-+#define PLL_M2_BUS_SHFT 0
-+#define PLL_M2_BUS_MASK (7<<PLL_M2_BUS_SHFT)
-+} PerfControl;
-+
-+#define PERF ((volatile PerfControl * const) PERF_BASE)
-+
-+typedef struct Timer {
-+ uint16 unused0;
-+ byte TimerMask;
-+#define TIMER0EN 0x01
-+#define TIMER1EN 0x02
-+#define TIMER2EN 0x04
-+ byte TimerInts;
-+#define TIMER0 0x01
-+#define TIMER1 0x02
-+#define TIMER2 0x04
-+#define WATCHDOG 0x08
-+ uint32 TimerCtl0;
-+ uint32 TimerCtl1;
-+ uint32 TimerCtl2;
-+#define TIMERENABLE 0x80000000
-+#define RSTCNTCLR 0x40000000
-+ uint32 TimerCnt0;
-+ uint32 TimerCnt1;
-+ uint32 TimerCnt2;
-+ uint32 WatchDogDefCount;
-+
-+ /* Write 0xff00 0x00ff to Start timer
-+ * Write 0xee00 0x00ee to Stop and re-load default count
-+ * Read from this register returns current watch dog count
-+ */
-+ uint32 WatchDogCtl;
-+
-+ /* Number of 40-MHz ticks for WD Reset pulse to last */
-+ uint32 WDResetCount;
-+} Timer;
-+
-+#define TIMER ((volatile Timer * const) TIMR_BASE)
-+
-+typedef struct UartChannel {
-+ byte unused0;
-+ byte control;
-+#define BRGEN 0x80 /* Control register bit defs */
-+#define TXEN 0x40
-+#define RXEN 0x20
-+#define LOOPBK 0x10
-+#define TXPARITYEN 0x08
-+#define TXPARITYEVEN 0x04
-+#define RXPARITYEN 0x02
-+#define RXPARITYEVEN 0x01
-+
-+ byte config;
-+#define XMITBREAK 0x40
-+#define BITS5SYM 0x00
-+#define BITS6SYM 0x10
-+#define BITS7SYM 0x20
-+#define BITS8SYM 0x30
-+#define ONESTOP 0x07
-+#define TWOSTOP 0x0f
-+ /* 4-LSBS represent STOP bits/char
-+ * in 1/8 bit-time intervals. Zero
-+ * represents 1/8 stop bit interval.
-+ * Fifteen represents 2 stop bits.
-+ */
-+ byte fifoctl;
-+#define RSTTXFIFOS 0x80
-+#define RSTRXFIFOS 0x40
-+ /* 5-bit TimeoutCnt is in low bits of this register.
-+ * This count represents the number of characters
-+ * idle times before setting receive Irq when below threshold
-+ */
-+ uint32 baudword;
-+ /* When divide SysClk/2/(1+baudword) we should get 32*bit-rate
-+ */
-+
-+ byte txf_levl; /* Read-only fifo depth */
-+ byte rxf_levl; /* Read-only fifo depth */
-+ byte fifocfg; /* Upper 4-bits are TxThresh, Lower are
-+ * RxThreshold. Irq can be asserted
-+ * when rx fifo> thresh, txfifo<thresh
-+ */
-+ byte prog_out; /* Set value of DTR (Bit0), RTS (Bit1)
-+ * if these bits are also enabled to GPIO_o
-+ */
-+#define DTREN 0x01
-+#define RTSEN 0x02
-+
-+ byte unused1;
-+ byte DeltaIPEdgeNoSense; /* Low 4-bits, set corr bit to 1 to
-+ * detect irq on rising AND falling
-+ * edges for corresponding GPIO_i
-+ * if enabled (edge insensitive)
-+ */
-+ byte DeltaIPConfig_Mask; /* Upper 4 bits: 1 for posedge sense
-+ * 0 for negedge sense if
-+ * not configured for edge
-+ * insensitive (see above)
-+ * Lower 4 bits: Mask to enable change
-+ * detection IRQ for corresponding
-+ * GPIO_i
-+ */
-+ byte DeltaIP_SyncIP; /* Upper 4 bits show which bits
-+ * have changed (may set IRQ).
-+ * read automatically clears bit
-+ * Lower 4 bits are actual status
-+ */
-+
-+ uint16 intMask; /* Same Bit defs for Mask and status */
-+ uint16 intStatus;
-+#define DELTAIP 0x0001
-+#define TXUNDERR 0x0002
-+#define TXOVFERR 0x0004
-+#define TXFIFOTHOLD 0x0008
-+#define TXREADLATCH 0x0010
-+#define TXFIFOEMT 0x0020
-+#define RXUNDERR 0x0040
-+#define RXOVFERR 0x0080
-+#define RXTIMEOUT 0x0100
-+#define RXFIFOFULL 0x0200
-+#define RXFIFOTHOLD 0x0400
-+#define RXFIFONE 0x0800
-+#define RXFRAMERR 0x1000
-+#define RXPARERR 0x2000
-+#define RXBRK 0x4000
-+
-+ uint16 unused2;
-+ uint16 Data; /* Write to TX, Read from RX */
-+ /* bits 11:8 are BRK,PAR,FRM errors */
-+
-+ uint32 unused3;
-+ uint32 unused4;
-+} Uart;
-+
-+#define UART ((volatile Uart * const) UART_BASE)
-+
-+typedef struct GpioControl {
-+ uint32 GPIODir_high; /* bits 36:32 */
-+ uint32 GPIODir; /* bits 31:00 */
-+ uint32 GPIOio_high; /* bits 36:32 */
-+ uint32 GPIOio; /* bits 31:00 */
-+ uint32 LEDCtrl;
-+#define LED3_STROBE 0x08000000
-+#define LED2_STROBE 0x04000000
-+#define LED1_STROBE 0x02000000
-+#define LED0_STROBE 0x01000000
-+#define LED_TEST 0x00010000
-+#define LED3_DISABLE_LINK_ACT 0x00008000
-+#define LED2_DISABLE_LINK_ACT 0x00004000
-+#define LED1_DISABLE_LINK_ACT 0x00002000
-+#define LED0_DISABLE_LINK_ACT 0x00001000
-+#define LED_INTERVAL_SET_MASK 0x00000f00
-+#define LED_INTERVAL_SET_320MS 0x00000500
-+#define LED_INTERVAL_SET_160MS 0x00000400
-+#define LED_INTERVAL_SET_80MS 0x00000300
-+#define LED_INTERVAL_SET_40MS 0x00000200
-+#define LED_INTERVAL_SET_20MS 0x00000100
-+#define LED3_ON 0x00000080
-+#define LED2_ON 0x00000040
-+#define LED1_ON 0x00000020
-+#define LED0_ON 0x00000010
-+#define LED3_ENABLE 0x00000008
-+#define LED2_ENABLE 0x00000004
-+#define LED1_ENABLE 0x00000002
-+#define LED0_ENABLE 0x00000001
-+ uint32 SpiSlaveCfg;
-+#define SPI_SLAVE_RESET 0x00010000
-+#define SPI_RESTRICT 0x00000400
-+#define SPI_DELAY_DISABLE 0x00000200
-+#define SPI_PROBE_MUX_SEL_MASK 0x000001e0
-+#define SPI_SER_ADDR_CFG_MASK 0x0000000c
-+#define SPI_MODE 0x00000001
-+ uint32 GPIOMode;
-+#define GROUP4_DIAG 0x00090000
-+#define GROUP4_UTOPIA 0x00080000
-+#define GROUP4_LEGACY_LED 0x00030000
-+#define GROUP4_MII_SNOOP 0x00020000
-+#define GROUP4_EXT_EPHY 0x00010000
-+#define GROUP3_DIAG 0x00009000
-+#define GROUP3_UTOPIA 0x00008000
-+#define GROUP3_EXT_MII 0x00007000
-+#define GROUP2_DIAG 0x00000900
-+#define GROUP2_PCI 0x00000500
-+#define GROUP1_DIAG 0x00000090
-+#define GROUP1_UTOPIA 0x00000080
-+#define GROUP1_SPI_UART 0x00000060
-+#define GROUP1_SPI_MASTER 0x00000060
-+#define GROUP1_MII_PCCARD 0x00000040
-+#define GROUP1_MII_SNOOP 0x00000020
-+#define GROUP1_EXT_EPHY 0x00000010
-+#define GROUP0_DIAG 0x00000009
-+#define GROUP0_EXT_MII 0x00000007
-+
-+} GpioControl;
-+
-+#define GPIO ((volatile GpioControl * const) GPIO_BASE)
-+
-+/* Number to mask conversion macro used for GPIODir and GPIOio */
-+#define GPIO_NUM_TOTAL_BITS_MASK 0x3f
-+#define GPIO_NUM_MAX_BITS_MASK 0x1f
-+#define GPIO_NUM_TO_MASK(X) ( (((X) & GPIO_NUM_TOTAL_BITS_MASK) < 32) ? (1 << ((X) & GPIO_NUM_MAX_BITS_MASK)) : (0) )
-+
-+/* Number to mask conversion macro used for GPIODir_high and GPIOio_high */
-+#define GPIO_NUM_MAX_BITS_MASK_HIGH 0x07
-+#define GPIO_NUM_TO_MASK_HIGH(X) ( (((X) & GPIO_NUM_TOTAL_BITS_MASK) >= 32) ? (1 << ((X-32) & GPIO_NUM_MAX_BITS_MASK_HIGH)) : (0) )
-+
-+
-+/*
-+** External Bus Interface
-+*/
-+typedef struct EbiChipSelect {
-+ uint32 base; /* base address in upper 24 bits */
-+#define EBI_SIZE_8K 0
-+#define EBI_SIZE_16K 1
-+#define EBI_SIZE_32K 2
-+#define EBI_SIZE_64K 3
-+#define EBI_SIZE_128K 4
-+#define EBI_SIZE_256K 5
-+#define EBI_SIZE_512K 6
-+#define EBI_SIZE_1M 7
-+#define EBI_SIZE_2M 8
-+#define EBI_SIZE_4M 9
-+#define EBI_SIZE_8M 10
-+#define EBI_SIZE_16M 11
-+#define EBI_SIZE_32M 12
-+#define EBI_SIZE_64M 13
-+#define EBI_SIZE_128M 14
-+#define EBI_SIZE_256M 15
-+ uint32 config;
-+#define EBI_ENABLE 0x00000001 /* .. enable this range */
-+#define EBI_WAIT_STATES 0x0000000e /* .. mask for wait states */
-+#define EBI_WTST_SHIFT 1 /* .. for shifting wait states */
-+#define EBI_WORD_WIDE 0x00000010 /* .. 16-bit peripheral, else 8 */
-+#define EBI_WREN 0x00000020 /* enable posted writes */
-+#define EBI_POLARITY 0x00000040 /* .. set to invert something,
-+ ** don't know what yet */
-+#define EBI_TS_TA_MODE 0x00000080 /* .. use TS/TA mode */
-+#define EBI_TS_SEL 0x00000100 /* .. drive tsize, not bs_b */
-+#define EBI_FIFO 0x00000200 /* .. use fifo */
-+#define EBI_RE 0x00000400 /* .. Reverse Endian */
-+} EbiChipSelect;
-+
-+typedef struct MpiRegisters {
-+ EbiChipSelect cs[7]; /* size chip select configuration */
-+#define EBI_CS0_BASE 0
-+#define EBI_CS1_BASE 1
-+#define EBI_CS2_BASE 2
-+#define EBI_CS3_BASE 3
-+#define PCMCIA_COMMON_BASE 4
-+#define PCMCIA_ATTRIBUTE_BASE 5
-+#define PCMCIA_IO_BASE 6
-+ uint32 unused0[2]; /* reserved */
-+ uint32 ebi_control; /* ebi control */
-+ uint32 unused1[4]; /* reserved */
-+#define EBI_ACCESS_TIMEOUT 0x000007FF
-+ uint32 pcmcia_cntl1; /* pcmcia control 1 */
-+#define PCCARD_CARD_RESET 0x00040000
-+#define CARDBUS_ENABLE 0x00008000
-+#define PCMCIA_ENABLE 0x00004000
-+#define PCMCIA_GPIO_ENABLE 0x00002000
-+#define CARDBUS_IDSEL 0x00001F00
-+#define VS2_OEN 0x00000080
-+#define VS1_OEN 0x00000040
-+#define VS2_OUT 0x00000020
-+#define VS1_OUT 0x00000010
-+#define VS2_IN 0x00000008
-+#define VS1_IN 0x00000004
-+#define CD2_IN 0x00000002
-+#define CD1_IN 0x00000001
-+#define VS_MASK 0x0000000C
-+#define CD_MASK 0x00000003
-+ uint32 unused2; /* reserved */
-+ uint32 pcmcia_cntl2; /* pcmcia control 2 */
-+#define PCMCIA_BYTESWAP_DIS 0x00000002
-+#define PCMCIA_HALFWORD_EN 0x00000001
-+#define RW_ACTIVE_CNT_BIT 2
-+#define INACTIVE_CNT_BIT 8
-+#define CE_SETUP_CNT_BIT 16
-+#define CE_HOLD_CNT_BIT 24
-+ uint32 unused3[40]; /* reserved */
-+
-+ uint32 sp0range; /* PCI to internal system bus address space */
-+ uint32 sp0remap;
-+ uint32 sp0cfg;
-+ uint32 sp1range;
-+ uint32 sp1remap;
-+ uint32 sp1cfg;
-+
-+ uint32 EndianCfg;
-+
-+ uint32 l2pcfgctl; /* internal system bus to PCI IO/Cfg control */
-+#define DIR_CFG_SEL 0x80000000 /* change from PCI I/O access to PCI config access */
-+#define DIR_CFG_USEREG 0x40000000 /* use this register info for PCI configuration access */
-+#define DEVICE_NUMBER 0x00007C00 /* device number for the PCI configuration access */
-+#define FUNC_NUMBER 0x00000300 /* function number for the PCI configuration access */
-+#define REG_NUMBER 0x000000FC /* register number for the PCI configuration access */
-+#define CONFIG_TYPE 0x00000003 /* configuration type for the PCI configuration access */
-+
-+ uint32 l2pmrange1; /* internal system bus to PCI memory space */
-+#define PCI_SIZE_64K 0xFFFF0000
-+#define PCI_SIZE_128K 0xFFFE0000
-+#define PCI_SIZE_256K 0xFFFC0000
-+#define PCI_SIZE_512K 0xFFF80000
-+#define PCI_SIZE_1M 0xFFF00000
-+#define PCI_SIZE_2M 0xFFE00000
-+#define PCI_SIZE_4M 0xFFC00000
-+#define PCI_SIZE_8M 0xFF800000
-+#define PCI_SIZE_16M 0xFF000000
-+#define PCI_SIZE_32M 0xFE000000
-+ uint32 l2pmbase1; /* kseg0 or kseg1 address & 0x1FFFFFFF */
-+ uint32 l2pmremap1;
-+#define CARDBUS_MEM 0x00000004
-+#define MEM_WINDOW_EN 0x00000001
-+ uint32 l2pmrange2;
-+ uint32 l2pmbase2;
-+ uint32 l2pmremap2;
-+ uint32 l2piorange; /* internal system bus to PCI I/O space */
-+ uint32 l2piobase;
-+ uint32 l2pioremap;
-+
-+ uint32 pcimodesel;
-+#define PCI2_INT_BUS_RD_PREFECH 0x000000F0
-+#define PCI_BAR2_NOSWAP 0x00000002 /* BAR at offset 0x20 */
-+#define PCI_BAR1_NOSWAP 0x00000001 /* BAR at affset 0x1c */
-+
-+ uint32 pciintstat; /* PCI interrupt mask/status */
-+#define MAILBOX1_SENT 0x08
-+#define MAILBOX0_SENT 0x04
-+#define MAILBOX1_MSG_RCV 0x02
-+#define MAILBOX0_MSG_RCV 0x01
-+ uint32 locbuscntrl; /* internal system bus control */
-+#define DIR_U2P_NOSWAP 0x00000002
-+#define EN_PCI_GPIO 0x00000001
-+ uint32 locintstat; /* internal system bus interrupt mask/status */
-+#define CSERR 0x0200
-+#define SERR 0x0100
-+#define EXT_PCI_INT 0x0080
-+#define DIR_FAILED 0x0040
-+#define DIR_COMPLETE 0x0020
-+#define PCI_CFG 0x0010
-+ uint32 unused5[7];
-+
-+ uint32 mailbox0;
-+ uint32 mailbox1;
-+
-+ uint32 pcicfgcntrl; /* internal system bus PCI configuration control */
-+#define PCI_CFG_REG_WRITE_EN 0x00000080
-+#define PCI_CFG_ADDR 0x0000003C
-+ uint32 pcicfgdata; /* internal system bus PCI configuration data */
-+
-+ uint32 locch2ctl; /* PCI to interrnal system bus DMA (downstream) local control */
-+#define MPI_DMA_HALT 0x00000008 /* idle after finish current memory burst */
-+#define MPI_DMA_PKT_HALT 0x00000004 /* idle after an EOP flag is detected */
-+#define MPI_DMA_STALL 0x00000002 /* idle after an EOP flag is detected */
-+#define MPI_DMA_ENABLE 0x00000001 /* set to enable channel */
-+ uint32 locch2intStat;
-+#define MPI_DMA_NO_DESC 0x00000004 /* no valid descriptors */
-+#define MPI_DMA_DONE 0x00000002 /* packet xfer complete */
-+#define MPI_DMA_BUFF_DONE 0x00000001 /* buffer done */
-+ uint32 locch2intMask;
-+ uint32 unused6;
-+ uint32 locch2descaddr;
-+ uint32 locch2status1;
-+#define LOCAL_DESC_STATE 0xE0000000
-+#define PCI_DESC_STATE 0x1C000000
-+#define BYTE_DONE 0x03FFC000
-+#define RING_ADDR 0x00003FFF
-+ uint32 locch2status2;
-+#define BUFPTR_OFFSET 0x1FFF0000
-+#define PCI_MASTER_STATE 0x000000C0
-+#define LOC_MASTER_STATE 0x00000038
-+#define CONTROL_STATE 0x00000007
-+ uint32 unused7;
-+
-+ uint32 locch1Ctl; /*internal system bus to PCI DMA (upstream) local control */
-+#define DMA_U2P_LE 0x00000200 /* local bus is little endian */
-+#define DMA_U2P_NOSWAP 0x00000100 /* lccal bus is little endian but no data swapped */
-+ uint32 locch1intstat;
-+ uint32 locch1intmask;
-+ uint32 unused8;
-+ uint32 locch1descaddr;
-+ uint32 locch1status1;
-+ uint32 locch1status2;
-+ uint32 unused9;
-+
-+ uint32 pcich1ctl; /* internal system bus to PCI DMA PCI control */
-+ uint32 pcich1intstat;
-+ uint32 pcich1intmask;
-+ uint32 pcich1descaddr;
-+ uint32 pcich1status1;
-+ uint32 pcich1status2;
-+
-+ uint32 pcich2Ctl; /* PCI to internal system bus DMA PCI control */
-+ uint32 pcich2intstat;
-+ uint32 pcich2intmask;
-+ uint32 pcich2descaddr;
-+ uint32 pcich2status1;
-+ uint32 pcich2status2;
-+
-+ uint32 perm_id; /* permanent device and vendor id */
-+ uint32 perm_rev; /* permanent revision id */
-+} MpiRegisters;
-+
-+#define MPI ((volatile MpiRegisters * const) MPI_BASE)
-+
-+/* PCI configuration address space start offset 0x40 */
-+#define BRCM_PCI_CONFIG_TIMER 0x40
-+#define BRCM_PCI_CONFIG_TIMER_RETRY_MASK 0x0000FF00
-+#define BRCM_PCI_CONFIG_TIMER_TRDY_MASK 0x000000FF
-+
-+/* USB host non-Open HCI register, USB_HOST_NON_OHCI, bit definitions. */
-+#define NON_OHCI_ENABLE_PORT1 0x00000001 /* Use USB port 1 for host, not dev */
-+#define NON_OHCI_BYTE_SWAP 0x00000008 /* Swap USB host registers */
-+
-+#define USBH_NON_OHCI ((volatile unsigned long * const) USB_HOST_NON_OHCI)
-+
-+#endif
-+
-diff -urN linux-2.6.19/arch/mips/bcm963xx/include/bcmTag.h linux-2.6.19.new/arch/mips/bcm963xx/include/bcmTag.h
---- linux-2.6.19/arch/mips/bcm963xx/include/bcmTag.h 1970-01-01 01:00:00.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/bcm963xx/include/bcmTag.h 2006-12-16 18:46:31.000000000 +0100
-@@ -0,0 +1,153 @@
-+/*
-+<:copyright-gpl
-+ Copyright 2002 Broadcom Corp. All Rights Reserved.
-+
-+ This program is free software; you can distribute it and/or modify it
-+ under the terms of the GNU General Public License (Version 2) as
-+ published by the Free Software Foundation.
-+
-+ This program is distributed in the hope it will be useful, but WITHOUT
-+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-+ for more details.
-+
-+ You should have received a copy of the GNU General Public License along
-+ with this program; if not, write to the Free Software Foundation, Inc.,
-+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-+:>
-+*/
-+//**************************************************************************************
-+// File Name : bcmTag.h
-+//
-+// Description: add tag with validation system to the firmware image file to be uploaded
-+// via http
-+//
-+// Created : 02/28/2002 seanl
-+//**************************************************************************************
-+
-+#ifndef _BCMTAG_H_
-+#define _BCMTAG_H_
-+
-+
-+#define BCM_SIG_1 "Broadcom Corporation"
-+#define BCM_SIG_2 "ver. 2.0" // was "firmware version 2.0" now it is split 6 char out for chip id.
-+
-+#define BCM_TAG_VER "6"
-+#define BCM_TAG_VER_LAST "26"
-+
-+// file tag (head) structure all is in clear text except validationTokens (crc, md5, sha1, etc). Total: 128 unsigned chars
-+#define TAG_LEN 256
-+#define TAG_VER_LEN 4
-+#define SIG_LEN 20
-+#define SIG_LEN_2 14 // Original second SIG = 20 is now devided into 14 for SIG_LEN_2 and 6 for CHIP_ID
-+#define CHIP_ID_LEN 6
-+#define IMAGE_LEN 10
-+#define ADDRESS_LEN 12
-+#define FLAG_LEN 2
-+#define TOKEN_LEN 20
-+#define BOARD_ID_LEN 16
-+#define RESERVED_LEN (TAG_LEN - TAG_VER_LEN - SIG_LEN - SIG_LEN_2 - CHIP_ID_LEN - BOARD_ID_LEN - \
-+ (4*IMAGE_LEN) - (3*ADDRESS_LEN) - (3*FLAG_LEN) - (2*TOKEN_LEN))
-+
-+
-+// TAG for downloadable image (kernel plus file system)
-+typedef struct _FILE_TAG
-+{
-+ unsigned char tagVersion[TAG_VER_LEN]; // tag version. Will be 2 here.
-+ unsigned char signiture_1[SIG_LEN]; // text line for company info
-+ unsigned char signiture_2[SIG_LEN_2]; // additional info (can be version number)
-+ unsigned char chipId[CHIP_ID_LEN]; // chip id
-+ unsigned char boardId[BOARD_ID_LEN]; // board id
-+ unsigned char bigEndian[FLAG_LEN]; // if = 1 - big, = 0 - little endia of the host
-+ unsigned char totalImageLen[IMAGE_LEN]; // the sum of all the following length
-+ unsigned char cfeAddress[ADDRESS_LEN]; // if non zero, cfe starting address
-+ unsigned char cfeLen[IMAGE_LEN]; // if non zero, cfe size in clear ASCII text.
-+ unsigned char rootfsAddress[ADDRESS_LEN]; // if non zero, filesystem starting address
-+ unsigned char rootfsLen[IMAGE_LEN]; // if non zero, filesystem size in clear ASCII text.
-+ unsigned char kernelAddress[ADDRESS_LEN]; // if non zero, kernel starting address
-+ unsigned char kernelLen[IMAGE_LEN]; // if non zero, kernel size in clear ASCII text.
-+ unsigned char dualImage[FLAG_LEN]; // if 1, dual image
-+ unsigned char inactiveLen[FLAG_LEN]; // if 1, the image is INACTIVE; if 0, active
-+ unsigned char reserved[RESERVED_LEN]; // reserved for later use
-+ unsigned char imageValidationToken[TOKEN_LEN];// image validation token - can be crc, md5, sha; for
-+ // now will be 4 unsigned char crc
-+ unsigned char tagValidationToken[TOKEN_LEN]; // validation token for tag(from signiture_1 to end of // mageValidationToken)
-+} FILE_TAG, *PFILE_TAG;
-+
-+#define CRC32_INIT_VALUE 0xffffffff /* Initial CRC32 checksum value */
-+#define CRC_LEN 4
-+
-+// only included if for bcmTag.exe program
-+#ifdef BCMTAG_EXE_USE
-+
-+static unsigned long Crc32_table[256] = {
-+ 0x00000000, 0x77073096, 0xEE0E612C, 0x990951BA,
-+ 0x076DC419, 0x706AF48F, 0xE963A535, 0x9E6495A3,
-+ 0x0EDB8832, 0x79DCB8A4, 0xE0D5E91E, 0x97D2D988,
-+ 0x09B64C2B, 0x7EB17CBD, 0xE7B82D07, 0x90BF1D91,
-+ 0x1DB71064, 0x6AB020F2, 0xF3B97148, 0x84BE41DE,
-+ 0x1ADAD47D, 0x6DDDE4EB, 0xF4D4B551, 0x83D385C7,
-+ 0x136C9856, 0x646BA8C0, 0xFD62F97A, 0x8A65C9EC,
-+ 0x14015C4F, 0x63066CD9, 0xFA0F3D63, 0x8D080DF5,
-+ 0x3B6E20C8, 0x4C69105E, 0xD56041E4, 0xA2677172,
-+ 0x3C03E4D1, 0x4B04D447, 0xD20D85FD, 0xA50AB56B,
-+ 0x35B5A8FA, 0x42B2986C, 0xDBBBC9D6, 0xACBCF940,
-+ 0x32D86CE3, 0x45DF5C75, 0xDCD60DCF, 0xABD13D59,
-+ 0x26D930AC, 0x51DE003A, 0xC8D75180, 0xBFD06116,
-+ 0x21B4F4B5, 0x56B3C423, 0xCFBA9599, 0xB8BDA50F,
-+ 0x2802B89E, 0x5F058808, 0xC60CD9B2, 0xB10BE924,
-+ 0x2F6F7C87, 0x58684C11, 0xC1611DAB, 0xB6662D3D,
-+ 0x76DC4190, 0x01DB7106, 0x98D220BC, 0xEFD5102A,
-+ 0x71B18589, 0x06B6B51F, 0x9FBFE4A5, 0xE8B8D433,
-+ 0x7807C9A2, 0x0F00F934, 0x9609A88E, 0xE10E9818,
-+ 0x7F6A0DBB, 0x086D3D2D, 0x91646C97, 0xE6635C01,
-+ 0x6B6B51F4, 0x1C6C6162, 0x856530D8, 0xF262004E,
-+ 0x6C0695ED, 0x1B01A57B, 0x8208F4C1, 0xF50FC457,
-+ 0x65B0D9C6, 0x12B7E950, 0x8BBEB8EA, 0xFCB9887C,
-+ 0x62DD1DDF, 0x15DA2D49, 0x8CD37CF3, 0xFBD44C65,
-+ 0x4DB26158, 0x3AB551CE, 0xA3BC0074, 0xD4BB30E2,
-+ 0x4ADFA541, 0x3DD895D7, 0xA4D1C46D, 0xD3D6F4FB,
-+ 0x4369E96A, 0x346ED9FC, 0xAD678846, 0xDA60B8D0,
-+ 0x44042D73, 0x33031DE5, 0xAA0A4C5F, 0xDD0D7CC9,
-+ 0x5005713C, 0x270241AA, 0xBE0B1010, 0xC90C2086,
-+ 0x5768B525, 0x206F85B3, 0xB966D409, 0xCE61E49F,
-+ 0x5EDEF90E, 0x29D9C998, 0xB0D09822, 0xC7D7A8B4,
-+ 0x59B33D17, 0x2EB40D81, 0xB7BD5C3B, 0xC0BA6CAD,
-+ 0xEDB88320, 0x9ABFB3B6, 0x03B6E20C, 0x74B1D29A,
-+ 0xEAD54739, 0x9DD277AF, 0x04DB2615, 0x73DC1683,
-+ 0xE3630B12, 0x94643B84, 0x0D6D6A3E, 0x7A6A5AA8,
-+ 0xE40ECF0B, 0x9309FF9D, 0x0A00AE27, 0x7D079EB1,
-+ 0xF00F9344, 0x8708A3D2, 0x1E01F268, 0x6906C2FE,
-+ 0xF762575D, 0x806567CB, 0x196C3671, 0x6E6B06E7,
-+ 0xFED41B76, 0x89D32BE0, 0x10DA7A5A, 0x67DD4ACC,
-+ 0xF9B9DF6F, 0x8EBEEFF9, 0x17B7BE43, 0x60B08ED5,
-+ 0xD6D6A3E8, 0xA1D1937E, 0x38D8C2C4, 0x4FDFF252,
-+ 0xD1BB67F1, 0xA6BC5767, 0x3FB506DD, 0x48B2364B,
-+ 0xD80D2BDA, 0xAF0A1B4C, 0x36034AF6, 0x41047A60,
-+ 0xDF60EFC3, 0xA867DF55, 0x316E8EEF, 0x4669BE79,
-+ 0xCB61B38C, 0xBC66831A, 0x256FD2A0, 0x5268E236,
-+ 0xCC0C7795, 0xBB0B4703, 0x220216B9, 0x5505262F,
-+ 0xC5BA3BBE, 0xB2BD0B28, 0x2BB45A92, 0x5CB36A04,
-+ 0xC2D7FFA7, 0xB5D0CF31, 0x2CD99E8B, 0x5BDEAE1D,
-+ 0x9B64C2B0, 0xEC63F226, 0x756AA39C, 0x026D930A,
-+ 0x9C0906A9, 0xEB0E363F, 0x72076785, 0x05005713,
-+ 0x95BF4A82, 0xE2B87A14, 0x7BB12BAE, 0x0CB61B38,
-+ 0x92D28E9B, 0xE5D5BE0D, 0x7CDCEFB7, 0x0BDBDF21,
-+ 0x86D3D2D4, 0xF1D4E242, 0x68DDB3F8, 0x1FDA836E,
-+ 0x81BE16CD, 0xF6B9265B, 0x6FB077E1, 0x18B74777,
-+ 0x88085AE6, 0xFF0F6A70, 0x66063BCA, 0x11010B5C,
-+ 0x8F659EFF, 0xF862AE69, 0x616BFFD3, 0x166CCF45,
-+ 0xA00AE278, 0xD70DD2EE, 0x4E048354, 0x3903B3C2,
-+ 0xA7672661, 0xD06016F7, 0x4969474D, 0x3E6E77DB,
-+ 0xAED16A4A, 0xD9D65ADC, 0x40DF0B66, 0x37D83BF0,
-+ 0xA9BCAE53, 0xDEBB9EC5, 0x47B2CF7F, 0x30B5FFE9,
-+ 0xBDBDF21C, 0xCABAC28A, 0x53B39330, 0x24B4A3A6,
-+ 0xBAD03605, 0xCDD70693, 0x54DE5729, 0x23D967BF,
-+ 0xB3667A2E, 0xC4614AB8, 0x5D681B02, 0x2A6F2B94,
-+ 0xB40BBE37, 0xC30C8EA1, 0x5A05DF1B, 0x2D02EF8D
-+};
-+#endif // BCMTAG_USE
-+
-+
-+#endif // _BCMTAG_H_
-+
-diff -urN linux-2.6.19/arch/mips/bcm963xx/include/bcm_intr.h linux-2.6.19.new/arch/mips/bcm963xx/include/bcm_intr.h
---- linux-2.6.19/arch/mips/bcm963xx/include/bcm_intr.h 1970-01-01 01:00:00.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/bcm963xx/include/bcm_intr.h 2006-12-16 18:46:31.000000000 +0100
-@@ -0,0 +1,59 @@
-+/*
-+<:copyright-gpl
-+ Copyright 2003 Broadcom Corp. All Rights Reserved.
-+
-+ This program is free software; you can distribute it and/or modify it
-+ under the terms of the GNU General Public License (Version 2) as
-+ published by the Free Software Foundation.
-+
-+ This program is distributed in the hope it will be useful, but WITHOUT
-+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-+ for more details.
-+
-+ You should have received a copy of the GNU General Public License along
-+ with this program; if not, write to the Free Software Foundation, Inc.,
-+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-+:>
-+*/
-+
-+#ifndef __BCM_INTR_H
-+#define __BCM_INTR_H
-+
-+#ifdef __cplusplus
-+ extern "C" {
-+#endif
-+
-+#if defined(CONFIG_BCM96338)
-+#include <6338_intr.h>
-+#endif
-+#if defined(CONFIG_BCM96345)
-+#include <6345_intr.h>
-+#endif
-+#if defined(CONFIG_BCM96348)
-+#include <6348_intr.h>
-+#endif
-+
-+/* defines */
-+struct pt_regs;
-+typedef int (*FN_HANDLER) (int, void *);
-+
-+/* prototypes */
-+extern void enable_brcm_irq(unsigned int irq);
-+extern void disable_brcm_irq(unsigned int irq);
-+extern int request_external_irq(unsigned int irq,
-+ FN_HANDLER handler, unsigned long irqflags,
-+ const char * devname, void *dev_id);
-+extern unsigned int BcmHalMapInterrupt(FN_HANDLER isr, unsigned int param,
-+ unsigned int interruptId);
-+extern void dump_intr_regs(void);
-+
-+/* compatibility definitions */
-+#define BcmHalInterruptEnable(irq) enable_brcm_irq( irq )
-+#define BcmHalInterruptDisable(irq) disable_brcm_irq( irq )
-+
-+#ifdef __cplusplus
-+ }
-+#endif
-+
-+#endif
-diff -urN linux-2.6.19/arch/mips/bcm963xx/include/bcm_map_part.h linux-2.6.19.new/arch/mips/bcm963xx/include/bcm_map_part.h
---- linux-2.6.19/arch/mips/bcm963xx/include/bcm_map_part.h 1970-01-01 01:00:00.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/bcm963xx/include/bcm_map_part.h 2006-12-16 18:46:31.000000000 +0100
-@@ -0,0 +1,34 @@
-+/*
-+<:copyright-gpl
-+ Copyright 2004 Broadcom Corp. All Rights Reserved.
-+
-+ This program is free software; you can distribute it and/or modify it
-+ under the terms of the GNU General Public License (Version 2) as
-+ published by the Free Software Foundation.
-+
-+ This program is distributed in the hope it will be useful, but WITHOUT
-+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-+ for more details.
-+
-+ You should have received a copy of the GNU General Public License along
-+ with this program; if not, write to the Free Software Foundation, Inc.,
-+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-+:>
-+*/
-+
-+#ifndef __BCM_MAP_PART_H
-+#define __BCM_MAP_PART_H
-+
-+#if defined(CONFIG_BCM96338)
-+#include <6338_map_part.h>
-+#endif
-+#if defined(CONFIG_BCM96345)
-+#include <6345_map_part.h>
-+#endif
-+#if defined(CONFIG_BCM96348)
-+#include <6348_map_part.h>
-+#endif
-+
-+#endif
-+
-diff -urN linux-2.6.19/arch/mips/bcm963xx/include/bcmpci.h linux-2.6.19.new/arch/mips/bcm963xx/include/bcmpci.h
---- linux-2.6.19/arch/mips/bcm963xx/include/bcmpci.h 1970-01-01 01:00:00.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/bcm963xx/include/bcmpci.h 2006-12-16 18:46:31.000000000 +0100
-@@ -0,0 +1,87 @@
-+/*
-+<:copyright-gpl
-+ Copyright 2004 Broadcom Corp. All Rights Reserved.
-+
-+ This program is free software; you can distribute it and/or modify it
-+ under the terms of the GNU General Public License (Version 2) as
-+ published by the Free Software Foundation.
-+
-+ This program is distributed in the hope it will be useful, but WITHOUT
-+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-+ for more details.
-+
-+ You should have received a copy of the GNU General Public License along
-+ with this program; if not, write to the Free Software Foundation, Inc.,
-+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-+:>
-+*/
-+
-+//
-+// bcmpci.h - bcm96348 PCI, Cardbus, and PCMCIA definition
-+//
-+#ifndef BCMPCI_H
-+#define BCMPCI_H
-+
-+/* Memory window in internal system bus address space */
-+#define BCM_PCI_MEM_BASE 0x08000000
-+/* IO window in internal system bus address space */
-+#define BCM_PCI_IO_BASE 0x0C000000
-+
-+#define BCM_PCI_ADDR_MASK 0x1fffffff
-+
-+/* Memory window size (range) */
-+#define BCM_PCI_MEM_SIZE_16MB 0x01000000
-+/* IO window size (range) */
-+#define BCM_PCI_IO_SIZE_64KB 0x00010000
-+
-+/* PCI Configuration and I/O space acesss */
-+#define BCM_PCI_CFG(d, f, o) ( (d << 11) | (f << 8) | (o/4 << 2) )
-+
-+/* fake USB PCI slot */
-+#define USB_HOST_SLOT 9
-+#define USB_BAR0_MEM_SIZE 0x0800
-+
-+#define BCM_HOST_MEM_SPACE1 0x10000000
-+#define BCM_HOST_MEM_SPACE2 0x00000000
-+
-+/*
-+ * EBI bus clock is 33MHz and share with PCI bus
-+ * each clock cycle is 30ns.
-+ */
-+/* attribute memory access wait cnt for 4306 */
-+#define PCMCIA_ATTR_CE_HOLD 3 // data hold time 70ns
-+#define PCMCIA_ATTR_CE_SETUP 3 // data setup time 50ns
-+#define PCMCIA_ATTR_INACTIVE 6 // time between read/write cycles 180ns. For the total cycle time 600ns (cnt1+cnt2+cnt3+cnt4)
-+#define PCMCIA_ATTR_ACTIVE 10 // OE/WE pulse width 300ns
-+
-+/* common memory access wait cnt for 4306 */
-+#define PCMCIA_MEM_CE_HOLD 1 // data hold time 30ns
-+#define PCMCIA_MEM_CE_SETUP 1 // data setup time 30ns
-+#define PCMCIA_MEM_INACTIVE 2 // time between read/write cycles 40ns. For the total cycle time 250ns (cnt1+cnt2+cnt3+cnt4)
-+#define PCMCIA_MEM_ACTIVE 5 // OE/WE pulse width 150ns
-+
-+#define PCCARD_VCC_MASK 0x00070000 // Mask Reset also
-+#define PCCARD_VCC_33V 0x00010000
-+#define PCCARD_VCC_50V 0x00020000
-+
-+typedef enum {
-+ MPI_CARDTYPE_NONE, // No Card in slot
-+ MPI_CARDTYPE_PCMCIA, // 16-bit PCMCIA card in slot
-+ MPI_CARDTYPE_CARDBUS, // 32-bit CardBus card in slot
-+} CardType;
-+
-+#define CARDBUS_SLOT 0 // Slot 0 is default for CardBus
-+
-+#define pcmciaAttrOffset 0x00200000
-+#define pcmciaMemOffset 0x00000000
-+// Needs to be right above PCI I/O space. Give 0x8000 (32K) to PCMCIA.
-+#define pcmciaIoOffset (BCM_PCI_IO_BASE + 0x80000)
-+// Base Address is that mapped into the MPI ChipSelect registers.
-+// UBUS bridge MemoryWindow 0 outputs a 0x00 for the base.
-+#define pcmciaBase 0xbf000000
-+#define pcmciaAttr (pcmciaAttrOffset | pcmciaBase)
-+#define pcmciaMem (pcmciaMemOffset | pcmciaBase)
-+#define pcmciaIo (pcmciaIoOffset | pcmciaBase)
-+
-+#endif
-diff -urN linux-2.6.19/arch/mips/bcm963xx/include/bcmtypes.h linux-2.6.19.new/arch/mips/bcm963xx/include/bcmtypes.h
---- linux-2.6.19/arch/mips/bcm963xx/include/bcmtypes.h 1970-01-01 01:00:00.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/bcm963xx/include/bcmtypes.h 2006-12-16 18:46:31.000000000 +0100
-@@ -0,0 +1,160 @@
-+/*
-+<:copyright-gpl
-+ Copyright 2002 Broadcom Corp. All Rights Reserved.
-+
-+ This program is free software; you can distribute it and/or modify it
-+ under the terms of the GNU General Public License (Version 2) as
-+ published by the Free Software Foundation.
-+
-+ This program is distributed in the hope it will be useful, but WITHOUT
-+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-+ for more details.
-+
-+ You should have received a copy of the GNU General Public License along
-+ with this program; if not, write to the Free Software Foundation, Inc.,
-+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-+:>
-+*/
-+
-+//
-+// bcmtypes.h - misc useful typedefs
-+//
-+#ifndef BCMTYPES_H
-+#define BCMTYPES_H
-+
-+// These are also defined in typedefs.h in the application area, so I need to
-+// protect against re-definition.
-+
-+#ifndef _TYPEDEFS_H_
-+typedef unsigned char uint8;
-+typedef unsigned short uint16;
-+typedef unsigned long uint32;
-+typedef signed char int8;
-+typedef signed short int16;
-+typedef signed long int32;
-+#endif
-+
-+typedef unsigned char byte;
-+// typedef unsigned long sem_t;
-+
-+typedef unsigned long HANDLE,*PULONG,DWORD,*PDWORD;
-+typedef signed long LONG,*PLONG;
-+
-+typedef unsigned int *PUINT;
-+typedef signed int INT;
-+
-+typedef unsigned short *PUSHORT;
-+typedef signed short SHORT,*PSHORT;
-+typedef unsigned short WORD,*PWORD;
-+
-+typedef unsigned char *PUCHAR;
-+typedef signed char *PCHAR;
-+
-+typedef void *PVOID;
-+
-+typedef unsigned char BOOLEAN, *PBOOL, *PBOOLEAN;
-+
-+typedef unsigned char BYTE,*PBYTE;
-+
-+//#ifndef __GNUC__
-+//The following has been defined in Vxworks internally: vxTypesOld.h
-+//redefine under vxworks will cause error
-+typedef signed int *PINT;
-+
-+typedef signed char INT8;
-+typedef signed short INT16;
-+typedef signed long INT32;
-+
-+typedef unsigned char UINT8;
-+typedef unsigned short UINT16;
-+typedef unsigned long UINT32;
-+
-+typedef unsigned char UCHAR;
-+typedef unsigned short USHORT;
-+typedef unsigned int UINT;
-+typedef unsigned long ULONG;
-+
-+typedef void VOID;
-+typedef unsigned char BOOL;
-+
-+//#endif /* __GNUC__ */
-+
-+
-+// These are also defined in typedefs.h in the application area, so I need to
-+// protect against re-definition.
-+#ifndef TYPEDEFS_H
-+
-+// Maximum and minimum values for a signed 16 bit integer.
-+#define MAX_INT16 32767
-+#define MIN_INT16 -32768
-+
-+// Useful for true/false return values. This uses the
-+// Taligent notation (k for constant).
-+typedef enum
-+{
-+ kFalse = 0,
-+ kTrue = 1
-+} Bool;
-+
-+#endif
-+
-+/* macros to protect against unaligned accesses */
-+
-+#if 0
-+/* first arg is an address, second is a value */
-+#define PUT16( a, d ) { \
-+ *((byte *)a) = (byte)((d)>>8); \
-+ *(((byte *)a)+1) = (byte)(d); \
-+}
-+
-+#define PUT32( a, d ) { \
-+ *((byte *)a) = (byte)((d)>>24); \
-+ *(((byte *)a)+1) = (byte)((d)>>16); \
-+ *(((byte *)a)+2) = (byte)((d)>>8); \
-+ *(((byte *)a)+3) = (byte)(d); \
-+}
-+
-+/* first arg is an address, returns a value */
-+#define GET16( a ) ( \
-+ (*((byte *)a) << 8) | \
-+ (*(((byte *)a)+1)) \
-+)
-+
-+#define GET32( a ) ( \
-+ (*((byte *)a) << 24) | \
-+ (*(((byte *)a)+1) << 16) | \
-+ (*(((byte *)a)+2) << 8) | \
-+ (*(((byte *)a)+3)) \
-+)
-+#endif
-+
-+#ifndef YES
-+#define YES 1
-+#endif
-+
-+#ifndef NO
-+#define NO 0
-+#endif
-+
-+#ifndef IN
-+#define IN
-+#endif
-+
-+#ifndef OUT
-+#define OUT
-+#endif
-+
-+#ifndef TRUE
-+#define TRUE 1
-+#endif
-+
-+#ifndef FALSE
-+#define FALSE 0
-+#endif
-+
-+#define READ32(addr) (*(volatile UINT32 *)((ULONG)&addr))
-+#define READ16(addr) (*(volatile UINT16 *)((ULONG)&addr))
-+#define READ8(addr) (*(volatile UINT8 *)((ULONG)&addr))
-+
-+#endif
-diff -urN linux-2.6.19/arch/mips/bcm963xx/include/board.h linux-2.6.19.new/arch/mips/bcm963xx/include/board.h
---- linux-2.6.19/arch/mips/bcm963xx/include/board.h 1970-01-01 01:00:00.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/bcm963xx/include/board.h 2006-12-16 18:46:31.000000000 +0100
-@@ -0,0 +1,373 @@
-+/*
-+<:copyright-gpl
-+ Copyright 2002 Broadcom Corp. All Rights Reserved.
-+
-+ This program is free software; you can distribute it and/or modify it
-+ under the terms of the GNU General Public License (Version 2) as
-+ published by the Free Software Foundation.
-+
-+ This program is distributed in the hope it will be useful, but WITHOUT
-+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-+ for more details.
-+
-+ You should have received a copy of the GNU General Public License along
-+ with this program; if not, write to the Free Software Foundation, Inc.,
-+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-+:>
-+*/
-+/***********************************************************************/
-+/* */
-+/* MODULE: board.h */
-+/* DATE: 97/02/18 */
-+/* PURPOSE: Board specific information. This module should include */
-+/* all base device addresses and board specific macros. */
-+/* */
-+/***********************************************************************/
-+#ifndef _BOARD_H
-+#define _BOARD_H
-+
-+/*****************************************************************************/
-+/* Misc board definitions */
-+/*****************************************************************************/
-+
-+#define DYING_GASP_API
-+
-+/*****************************************************************************/
-+/* Physical Memory Map */
-+/*****************************************************************************/
-+
-+#define PHYS_DRAM_BASE 0x00000000 /* Dynamic RAM Base */
-+#define PHYS_FLASH_BASE 0x1FC00000 /* Flash Memory */
-+
-+/*****************************************************************************/
-+/* Note that the addresses above are physical addresses and that programs */
-+/* have to use converted addresses defined below: */
-+/*****************************************************************************/
-+#define DRAM_BASE (0x80000000 | PHYS_DRAM_BASE) /* cached DRAM */
-+#define DRAM_BASE_NOCACHE (0xA0000000 | PHYS_DRAM_BASE) /* uncached DRAM */
-+#define FLASH_BASE (0xA0000000 | PHYS_FLASH_BASE) /* uncached Flash */
-+
-+/*****************************************************************************/
-+/* Select the PLL value to get the desired CPU clock frequency. */
-+/* */
-+/* */
-+/*****************************************************************************/
-+#define FPERIPH 50000000
-+
-+#define ONEK 1024
-+#define BLK64K (64*ONEK)
-+#define FLASH45_BLKS_BOOT_ROM 1
-+#define FLASH45_LENGTH_BOOT_ROM (FLASH45_BLKS_BOOT_ROM * BLK64K)
-+#define FLASH_RESERVED_AT_END (64*ONEK) /*reserved for PSI, scratch pad*/
-+
-+/*****************************************************************************/
-+/* Note that the addresses above are physical addresses and that programs */
-+/* have to use converted addresses defined below: */
-+/*****************************************************************************/
-+#define DRAM_BASE (0x80000000 | PHYS_DRAM_BASE) /* cached DRAM */
-+#define DRAM_BASE_NOCACHE (0xA0000000 | PHYS_DRAM_BASE) /* uncached DRAM */
-+#define FLASH_BASE (0xA0000000 | PHYS_FLASH_BASE) /* uncached Flash */
-+
-+/*****************************************************************************/
-+/* Select the PLL value to get the desired CPU clock frequency. */
-+/* */
-+/* */
-+/*****************************************************************************/
-+#define FPERIPH 50000000
-+
-+#define SDRAM_TYPE_ADDRESS_OFFSET 16
-+#define NVRAM_DATA_OFFSET 0x0580
-+#define NVRAM_DATA_ID 0x0f1e2d3c
-+#define BOARD_SDRAM_TYPE *(unsigned long *) \
-+ (FLASH_BASE + SDRAM_TYPE_ADDRESS_OFFSET)
-+
-+#define ONEK 1024
-+#define BLK64K (64*ONEK)
-+
-+// nvram and psi flash definitions for 45
-+#define FLASH45_LENGTH_NVRAM ONEK // 1k nvram
-+#define NVRAM_PSI_DEFAULT 24 // default psi in K byes
-+
-+/*****************************************************************************/
-+/* NVRAM Offset and definition */
-+/*****************************************************************************/
-+
-+#define NVRAM_VERSION_NUMBER 2
-+#define NVRAM_VERSION_NUMBER_ADDRESS 0
-+
-+#define NVRAM_BOOTLINE_LEN 256
-+#define NVRAM_BOARD_ID_STRING_LEN 16
-+#define NVRAM_MAC_ADDRESS_LEN 6
-+#define NVRAM_MAC_COUNT_MAX 32
-+
-+/*****************************************************************************/
-+/* Misc Offsets */
-+/*****************************************************************************/
-+
-+#define CFE_VERSION_OFFSET 0x0570
-+#define CFE_VERSION_MARK_SIZE 5
-+#define CFE_VERSION_SIZE 5
-+
-+typedef struct
-+{
-+ unsigned long ulVersion;
-+ char szBootline[NVRAM_BOOTLINE_LEN];
-+ char szBoardId[NVRAM_BOARD_ID_STRING_LEN];
-+ unsigned long ulReserved1[2];
-+ unsigned long ulNumMacAddrs;
-+ unsigned char ucaBaseMacAddr[NVRAM_MAC_ADDRESS_LEN];
-+ char chReserved[2];
-+ unsigned long ulCheckSum;
-+} NVRAM_DATA, *PNVRAM_DATA;
-+
-+
-+/*****************************************************************************/
-+/* board ioctl calls for flash, led and some other utilities */
-+/*****************************************************************************/
-+
-+
-+/* Defines. for board driver */
-+#define BOARD_IOCTL_MAGIC 'B'
-+#define BOARD_DRV_MAJOR 206
-+
-+#define MAC_ADDRESS_ANY (unsigned long) -1
-+
-+#define BOARD_IOCTL_FLASH_INIT \
-+ _IOWR(BOARD_IOCTL_MAGIC, 0, BOARD_IOCTL_PARMS)
-+
-+#define BOARD_IOCTL_FLASH_WRITE \
-+ _IOWR(BOARD_IOCTL_MAGIC, 1, BOARD_IOCTL_PARMS)
-+
-+#define BOARD_IOCTL_FLASH_READ \
-+ _IOWR(BOARD_IOCTL_MAGIC, 2, BOARD_IOCTL_PARMS)
-+
-+#define BOARD_IOCTL_GET_NR_PAGES \
-+ _IOWR(BOARD_IOCTL_MAGIC, 3, BOARD_IOCTL_PARMS)
-+
-+#define BOARD_IOCTL_DUMP_ADDR \
-+ _IOWR(BOARD_IOCTL_MAGIC, 4, BOARD_IOCTL_PARMS)
-+
-+#define BOARD_IOCTL_SET_MEMORY \
-+ _IOWR(BOARD_IOCTL_MAGIC, 5, BOARD_IOCTL_PARMS)
-+
-+#define BOARD_IOCTL_MIPS_SOFT_RESET \
-+ _IOWR(BOARD_IOCTL_MAGIC, 6, BOARD_IOCTL_PARMS)
-+
-+#define BOARD_IOCTL_LED_CTRL \
-+ _IOWR(BOARD_IOCTL_MAGIC, 7, BOARD_IOCTL_PARMS)
-+
-+#define BOARD_IOCTL_GET_ID \
-+ _IOWR(BOARD_IOCTL_MAGIC, 8, BOARD_IOCTL_PARMS)
-+
-+#define BOARD_IOCTL_GET_MAC_ADDRESS \
-+ _IOWR(BOARD_IOCTL_MAGIC, 9, BOARD_IOCTL_PARMS)
-+
-+#define BOARD_IOCTL_RELEASE_MAC_ADDRESS \
-+ _IOWR(BOARD_IOCTL_MAGIC, 10, BOARD_IOCTL_PARMS)
-+
-+#define BOARD_IOCTL_GET_PSI_SIZE \
-+ _IOWR(BOARD_IOCTL_MAGIC, 11, BOARD_IOCTL_PARMS)
-+
-+#define BOARD_IOCTL_GET_SDRAM_SIZE \
-+ _IOWR(BOARD_IOCTL_MAGIC, 12, BOARD_IOCTL_PARMS)
-+
-+#define BOARD_IOCTL_SET_MONITOR_FD \
-+ _IOWR(BOARD_IOCTL_MAGIC, 13, BOARD_IOCTL_PARMS)
-+
-+#define BOARD_IOCTL_WAKEUP_MONITOR_TASK \
-+ _IOWR(BOARD_IOCTL_MAGIC, 14, BOARD_IOCTL_PARMS)
-+
-+#define BOARD_IOCTL_GET_BOOTLINE \
-+ _IOWR(BOARD_IOCTL_MAGIC, 15, BOARD_IOCTL_PARMS)
-+
-+#define BOARD_IOCTL_SET_BOOTLINE \
-+ _IOWR(BOARD_IOCTL_MAGIC, 16, BOARD_IOCTL_PARMS)
-+
-+#define BOARD_IOCTL_GET_BASE_MAC_ADDRESS \
-+ _IOWR(BOARD_IOCTL_MAGIC, 17, BOARD_IOCTL_PARMS)
-+
-+#define BOARD_IOCTL_GET_CHIP_ID \
-+ _IOWR(BOARD_IOCTL_MAGIC, 18, BOARD_IOCTL_PARMS)
-+
-+#define BOARD_IOCTL_GET_NUM_ENET \
-+ _IOWR(BOARD_IOCTL_MAGIC, 19, BOARD_IOCTL_PARMS)
-+
-+#define BOARD_IOCTL_GET_CFE_VER \
-+ _IOWR(BOARD_IOCTL_MAGIC, 20, BOARD_IOCTL_PARMS)
-+
-+#define BOARD_IOCTL_GET_ENET_CFG \
-+ _IOWR(BOARD_IOCTL_MAGIC, 21, BOARD_IOCTL_PARMS)
-+
-+#define BOARD_IOCTL_GET_WLAN_ANT_INUSE \
-+ _IOWR(BOARD_IOCTL_MAGIC, 22, BOARD_IOCTL_PARMS)
-+
-+#define BOARD_IOCTL_SET_TRIGGER_EVENT \
-+ _IOWR(BOARD_IOCTL_MAGIC, 23, BOARD_IOCTL_PARMS)
-+
-+#define BOARD_IOCTL_GET_TRIGGER_EVENT \
-+ _IOWR(BOARD_IOCTL_MAGIC, 24, BOARD_IOCTL_PARMS)
-+
-+#define BOARD_IOCTL_UNSET_TRIGGER_EVENT \
-+ _IOWR(BOARD_IOCTL_MAGIC, 25, BOARD_IOCTL_PARMS)
-+
-+#define BOARD_IOCTL_SET_SES_LED \
-+ _IOWR(BOARD_IOCTL_MAGIC, 26, BOARD_IOCTL_PARMS)
-+
-+//<<JUNHON, 2004/09/15, get reset button status , tim hou , 05/04/12
-+#define RESET_BUTTON_UP 1
-+#define RESET_BUTTON_PRESSDOWN 0
-+#define BOARD_IOCTL_GET_RESETHOLD \
-+ _IOWR(BOARD_IOCTL_MAGIC, 27, BOARD_IOCTL_PARMS)
-+//>>JUNHON, 2004/09/15
-+
-+// for the action in BOARD_IOCTL_PARMS for flash operation
-+typedef enum
-+{
-+ PERSISTENT,
-+ NVRAM,
-+ BCM_IMAGE_CFE,
-+ BCM_IMAGE_FS,
-+ BCM_IMAGE_KERNEL,
-+ BCM_IMAGE_WHOLE,
-+ SCRATCH_PAD,
-+ FLASH_SIZE,
-+} BOARD_IOCTL_ACTION;
-+
-+
-+typedef struct boardIoctParms
-+{
-+ char *string;
-+ char *buf;
-+ int strLen;
-+ int offset;
-+ BOARD_IOCTL_ACTION action; /* flash read/write: nvram, persistent, bcm image */
-+ int result;
-+} BOARD_IOCTL_PARMS;
-+
-+
-+// LED defines
-+typedef enum
-+{
-+ kLedAdsl,
-+ kLedWireless,
-+ kLedUsb,
-+ kLedHpna,
-+ kLedWanData,
-+ kLedPPP,
-+ kLedVoip,
-+ kLedSes,
-+ kLedLan,
-+ kLedSelfTest,
-+ kLedEnd, // NOTE: Insert the new led name before this one. Alway stay at the end.
-+} BOARD_LED_NAME;
-+
-+typedef enum
-+{
-+ kLedStateOff, /* turn led off */
-+ kLedStateOn, /* turn led on */
-+ kLedStateFail, /* turn led on red */
-+ kLedStateBlinkOnce, /* blink once, ~100ms and ignore the same call during the 100ms period */
-+ kLedStateSlowBlinkContinues, /* slow blink continues at ~600ms interval */
-+ kLedStateFastBlinkContinues, /* fast blink continues at ~200ms interval */
-+} BOARD_LED_STATE;
-+
-+
-+// virtual and physical map pair defined in board.c
-+typedef struct ledmappair
-+{
-+ BOARD_LED_NAME ledName; // virtual led name
-+ BOARD_LED_STATE ledInitState; // initial led state when the board boots.
-+ unsigned short ledMask; // physical GPIO pin mask
-+ unsigned short ledActiveLow; // reset bit to turn on LED
-+ unsigned short ledMaskFail; // physical GPIO pin mask for state failure
-+ unsigned short ledActiveLowFail;// reset bit to turn on LED
-+} LED_MAP_PAIR, *PLED_MAP_PAIR;
-+
-+typedef void (*HANDLE_LED_FUNC)(BOARD_LED_NAME ledName, BOARD_LED_STATE ledState);
-+
-+/* Flash storage address information that is determined by the flash driver. */
-+typedef struct flashaddrinfo
-+{
-+ int flash_persistent_start_blk;
-+ int flash_persistent_number_blk;
-+ int flash_persistent_length;
-+ unsigned long flash_persistent_blk_offset;
-+ int flash_scratch_pad_start_blk; // start before psi (SP_BUF_LEN)
-+ int flash_scratch_pad_number_blk;
-+ int flash_scratch_pad_length;
-+ unsigned long flash_scratch_pad_blk_offset;
-+ int flash_nvram_start_blk;
-+ int flash_nvram_number_blk;
-+ int flash_nvram_length;
-+ unsigned long flash_nvram_blk_offset;
-+} FLASH_ADDR_INFO, *PFLASH_ADDR_INFO;
-+
-+// scratch pad defines
-+/* SP - Persisten Scratch Pad format:
-+ sp header : 32 bytes
-+ tokenId-1 : 8 bytes
-+ tokenId-1 len : 4 bytes
-+ tokenId-1 data
-+ ....
-+ tokenId-n : 8 bytes
-+ tokenId-n len : 4 bytes
-+ tokenId-n data
-+*/
-+
-+#define MAGIC_NUM_LEN 8
-+#define MAGIC_NUMBER "gOGoBrCm"
-+#define TOKEN_NAME_LEN 16
-+#define SP_VERSION 1
-+#define SP_MAX_LEN 8 * 1024 // 8k buf before psi
-+#define SP_RESERVERD 16
-+
-+typedef struct _SP_HEADER
-+{
-+ char SPMagicNum[MAGIC_NUM_LEN]; // 8 bytes of magic number
-+ int SPVersion; // version number
-+ int SPUsedLen; // used sp len
-+ char SPReserved[SP_RESERVERD]; // reservied, total 32 bytes
-+} SP_HEADER, *PSP_HEADER;
-+
-+typedef struct _TOKEN_DEF
-+{
-+ char tokenName[TOKEN_NAME_LEN];
-+ int tokenLen;
-+} SP_TOKEN, *PSP_TOKEN;
-+
-+
-+/*****************************************************************************/
-+/* Function Prototypes */
-+/*****************************************************************************/
-+#if !defined(__ASM_ASM_H)
-+void dumpaddr( unsigned char *pAddr, int nLen );
-+
-+int kerSysNvRamGet(char *string, int strLen, int offset);
-+int kerSysNvRamSet(char *string, int strLen, int offset);
-+int kerSysPersistentGet(char *string, int strLen, int offset);
-+int kerSysPersistentSet(char *string, int strLen, int offset);
-+int kerSysScratchPadGet(char *tokName, char *tokBuf, int tokLen);
-+int kerSysScratchPadSet(char *tokName, char *tokBuf, int tokLen);
-+int kerSysBcmImageSet( int flash_start_addr, char *string, int size);
-+int kerSysGetMacAddress( unsigned char *pucaAddr, unsigned long ulId );
-+int kerSysReleaseMacAddress( unsigned char *pucaAddr );
-+int kerSysGetSdramSize( void );
-+void kerSysGetBootline(char *string, int strLen);
-+void kerSysSetBootline(char *string, int strLen);
-+void kerSysMipsSoftReset(void);
-+void kerSysLedCtrl(BOARD_LED_NAME, BOARD_LED_STATE);
-+void kerSysLedRegisterHwHandler( BOARD_LED_NAME, HANDLE_LED_FUNC, int );
-+int kerSysFlashSizeGet(void);
-+void kerSysRegisterDyingGaspHandler(char *devname, void *cbfn, void *context);
-+void kerSysDeregisterDyingGaspHandler(char *devname);
-+void kerSysWakeupMonitorTask( void );
-+#endif
-+
-+#define BOOT_CFE 0
-+#define BOOT_REDBOOT 1
-+
-+extern int boot_loader_type;
-+
-+#endif /* _BOARD_H */
-+
-diff -urN linux-2.6.19/arch/mips/bcm963xx/int-handler.S linux-2.6.19.new/arch/mips/bcm963xx/int-handler.S
---- linux-2.6.19/arch/mips/bcm963xx/int-handler.S 1970-01-01 01:00:00.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/bcm963xx/int-handler.S 2006-12-16 18:46:31.000000000 +0100
-@@ -0,0 +1,59 @@
-+/*
-+<:copyright-gpl
-+ Copyright 2002 Broadcom Corp. All Rights Reserved.
-+
-+ This program is free software; you can distribute it and/or modify it
-+ under the terms of the GNU General Public License (Version 2) as
-+ published by the Free Software Foundation.
-+
-+ This program is distributed in the hope it will be useful, but WITHOUT
-+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-+ for more details.
-+
-+ You should have received a copy of the GNU General Public License along
-+ with this program; if not, write to the Free Software Foundation, Inc.,
-+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-+:>
-+*/
-+/*
-+ * Generic interrupt handler for Broadcom MIPS boards
-+ */
-+
-+#include <linux/autoconf.h>
-+
-+#include <asm/asm.h>
-+#include <asm/mipsregs.h>
-+#include <asm/regdef.h>
-+#include <asm/stackframe.h>
-+
-+/*
-+ * MIPS IRQ Source
-+ * -------- ------
-+ * 0 Software (ignored)
-+ * 1 Software (ignored)
-+ * 2 Combined hardware interrupt (hw0)
-+ * 3 Hardware
-+ * 4 Hardware
-+ * 5 Hardware
-+ * 6 Hardware
-+ * 7 R4k timer
-+ */
-+
-+ .text
-+ .set noreorder
-+ .set noat
-+ .align 5
-+ NESTED(brcmIRQ, PT_SIZE, sp)
-+ SAVE_ALL
-+ CLI
-+ .set noreorder
-+ .set at
-+
-+ jal plat_irq_dispatch
-+ move a0, sp
-+
-+ j ret_from_irq
-+ nop
-+
-+ END(brcmIRQ)
-diff -urN linux-2.6.19/arch/mips/bcm963xx/irq.c linux-2.6.19.new/arch/mips/bcm963xx/irq.c
---- linux-2.6.19/arch/mips/bcm963xx/irq.c 1970-01-01 01:00:00.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/bcm963xx/irq.c 2006-12-16 18:46:31.000000000 +0100
-@@ -0,0 +1,256 @@
-+/*
-+<:copyright-gpl
-+ Copyright 2002 Broadcom Corp. All Rights Reserved.
-+
-+ This program is free software; you can distribute it and/or modify it
-+ under the terms of the GNU General Public License (Version 2) as
-+ published by the Free Software Foundation.
-+
-+ This program is distributed in the hope it will be useful, but WITHOUT
-+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-+ for more details.
-+
-+ You should have received a copy of the GNU General Public License along
-+ with this program; if not, write to the Free Software Foundation, Inc.,
-+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-+:>
-+*/
-+/*
-+ * Interrupt control functions for Broadcom 963xx MIPS boards
-+ */
-+
-+#include <asm/atomic.h>
-+
-+#include <linux/delay.h>
-+#include <linux/init.h>
-+#include <linux/ioport.h>
-+#include <linux/irq.h>
-+#include <linux/interrupt.h>
-+#include <linux/kernel.h>
-+#include <linux/slab.h>
-+#include <linux/module.h>
-+
-+#include <asm/irq.h>
-+#include <asm/mipsregs.h>
-+#include <asm/addrspace.h>
-+#include <asm/signal.h>
-+#include <bcm_map_part.h>
-+#include <bcm_intr.h>
-+
-+static void irq_dispatch_int(struct pt_regs *regs)
-+{
-+ unsigned int pendingIrqs;
-+ static unsigned int irqBit;
-+ static unsigned int isrNumber = 31;
-+
-+ pendingIrqs = PERF->IrqStatus & PERF->IrqMask;
-+ if (!pendingIrqs) {
-+ return;
-+ }
-+
-+ while (1) {
-+ irqBit <<= 1;
-+ isrNumber++;
-+ if (isrNumber == 32) {
-+ isrNumber = 0;
-+ irqBit = 0x1;
-+ }
-+ if (pendingIrqs & irqBit) {
-+ PERF->IrqMask &= ~irqBit; // mask
-+ do_IRQ(isrNumber + INTERNAL_ISR_TABLE_OFFSET);
-+ break;
-+ }
-+ }
-+}
-+
-+static void irq_dispatch_ext(uint32 irq)
-+{
-+ if (!(PERF->ExtIrqCfg & (1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_MASK_SHFT)))) {
-+ printk("**** Ext IRQ mask. Should not dispatch ****\n");
-+ }
-+ /* disable and clear interrupt in the controller */
-+ PERF->ExtIrqCfg |= (1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_CLEAR_SHFT));
-+ PERF->ExtIrqCfg &= ~(1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_MASK_SHFT));
-+ do_IRQ(irq);
-+}
-+
-+
-+extern void brcm_timer_interrupt(struct pt_regs *regs);
-+
-+asmlinkage void plat_irq_dispatch(struct pt_regs *regs)
-+{
-+ u32 cause;
-+ while((cause = (read_c0_cause()& CAUSEF_IP))) {
-+ if (cause & CAUSEF_IP7)
-+ brcm_timer_interrupt(regs);
-+ else if (cause & CAUSEF_IP2)
-+ irq_dispatch_int(regs);
-+ else if (cause & CAUSEF_IP3)
-+ irq_dispatch_ext(INTERRUPT_ID_EXTERNAL_0);
-+ else if (cause & CAUSEF_IP4)
-+ irq_dispatch_ext(INTERRUPT_ID_EXTERNAL_1);
-+ else if (cause & CAUSEF_IP5)
-+ irq_dispatch_ext(INTERRUPT_ID_EXTERNAL_2);
-+ else if (cause & CAUSEF_IP6)
-+ irq_dispatch_ext(INTERRUPT_ID_EXTERNAL_3);
-+ local_irq_disable();
-+ }
-+}
-+
-+
-+void enable_brcm_irq(unsigned int irq)
-+{
-+ unsigned long flags;
-+
-+ local_irq_save(flags);
-+ if( irq >= INTERNAL_ISR_TABLE_OFFSET ) {
-+ PERF->IrqMask |= (1 << (irq - INTERNAL_ISR_TABLE_OFFSET));
-+ }
-+ else if (irq >= INTERRUPT_ID_EXTERNAL_0 && irq <= INTERRUPT_ID_EXTERNAL_3) {
-+ /* enable and clear interrupt in the controller */
-+ PERF->ExtIrqCfg |= (1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_CLEAR_SHFT));
-+ PERF->ExtIrqCfg |= (1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_MASK_SHFT));
-+ }
-+ local_irq_restore(flags);
-+}
-+
-+void disable_brcm_irq(unsigned int irq)
-+{
-+ unsigned long flags;
-+
-+ local_irq_save(flags);
-+ if( irq >= INTERNAL_ISR_TABLE_OFFSET ) {
-+ PERF->IrqMask &= ~(1 << (irq - INTERNAL_ISR_TABLE_OFFSET));
-+ }
-+ else if (irq >= INTERRUPT_ID_EXTERNAL_0 && irq <= INTERRUPT_ID_EXTERNAL_3) {
-+ /* disable interrupt in the controller */
-+ PERF->ExtIrqCfg &= ~(1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_MASK_SHFT));
-+ }
-+ local_irq_restore(flags);
-+}
-+
-+void ack_brcm_irq(unsigned int irq)
-+{
-+ /* Already done in brcm_irq_dispatch */
-+}
-+
-+unsigned int startup_brcm_irq(unsigned int irq)
-+{
-+ enable_brcm_irq(irq);
-+
-+ return 0; /* never anything pending */
-+}
-+
-+unsigned int startup_brcm_none(unsigned int irq)
-+{
-+ return 0;
-+}
-+
-+void end_brcm_irq(unsigned int irq)
-+{
-+ if (!(irq_desc[irq].status & (IRQ_DISABLED|IRQ_INPROGRESS)))
-+ enable_brcm_irq(irq);
-+}
-+
-+void end_brcm_none(unsigned int irq)
-+{
-+}
-+
-+static struct hw_interrupt_type brcm_irq_type = {
-+ .typename = "MIPS",
-+ .startup = startup_brcm_irq,
-+ .shutdown = disable_brcm_irq,
-+ .enable = enable_brcm_irq,
-+ .disable = disable_brcm_irq,
-+ .ack = ack_brcm_irq,
-+ .end = end_brcm_irq,
-+ .set_affinity = NULL
-+};
-+
-+static struct hw_interrupt_type brcm_irq_no_end_type = {
-+ .typename = "MIPS",
-+ .startup = startup_brcm_none,
-+ .shutdown = disable_brcm_irq,
-+ .enable = enable_brcm_irq,
-+ .disable = disable_brcm_irq,
-+ .ack = ack_brcm_irq,
-+ .end = end_brcm_none,
-+ .set_affinity = NULL
-+};
-+
-+void __init arch_init_irq(void)
-+{
-+ int i;
-+
-+ clear_c0_status(ST0_BEV);
-+ change_c0_status(ST0_IM, (IE_IRQ0 | IE_IRQ1 | IE_IRQ2 | IE_IRQ3 | IE_IRQ4));
-+
-+ for (i = 0; i < NR_IRQS; i++) {
-+ irq_desc[i].status = IRQ_DISABLED;
-+ irq_desc[i].action = 0;
-+ irq_desc[i].depth = 1;
-+ irq_desc[i].chip = &brcm_irq_type;
-+ }
-+}
-+
-+int request_external_irq(unsigned int irq,
-+ FN_HANDLER handler,
-+ unsigned long irqflags,
-+ const char * devname,
-+ void *dev_id)
-+{
-+ unsigned long flags;
-+
-+ local_irq_save(flags);
-+
-+ PERF->ExtIrqCfg |= (1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_CLEAR_SHFT)); // Clear
-+ PERF->ExtIrqCfg &= ~(1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_MASK_SHFT)); // Mask
-+ PERF->ExtIrqCfg &= ~(1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_INSENS_SHFT)); // Edge insesnsitive
-+ PERF->ExtIrqCfg |= (1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_LEVEL_SHFT)); // Level triggered
-+ PERF->ExtIrqCfg &= ~(1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_SENSE_SHFT)); // Low level
-+
-+ local_irq_restore(flags);
-+
-+ return( request_irq(irq, handler, irqflags, devname, dev_id) );
-+}
-+
-+/* VxWorks compatibility function(s). */
-+
-+unsigned int BcmHalMapInterrupt(FN_HANDLER pfunc, unsigned int param,
-+ unsigned int interruptId)
-+{
-+ int nRet = -1;
-+ char *devname;
-+
-+ devname = kmalloc(16, GFP_KERNEL);
-+ if (devname)
-+ sprintf( devname, "brcm_%d", interruptId );
-+
-+ /* Set the IRQ description to not automatically enable the interrupt at
-+ * the end of an ISR. The driver that handles the interrupt must
-+ * explicitly call BcmHalInterruptEnable or enable_brcm_irq. This behavior
-+ * is consistent with interrupt handling on VxWorks.
-+ */
-+ irq_desc[interruptId].chip = &brcm_irq_no_end_type;
-+
-+ if( interruptId >= INTERNAL_ISR_TABLE_OFFSET )
-+ {
-+ nRet = request_irq( interruptId, pfunc, SA_SAMPLE_RANDOM | SA_INTERRUPT,
-+ devname, (void *) param );
-+ }
-+ else if (interruptId >= INTERRUPT_ID_EXTERNAL_0 && interruptId <= INTERRUPT_ID_EXTERNAL_3)
-+ {
-+ nRet = request_external_irq( interruptId, pfunc, SA_SAMPLE_RANDOM | SA_INTERRUPT,
-+ devname, (void *) param );
-+ }
-+
-+ return( nRet );
-+}
-+
-+
-+EXPORT_SYMBOL(enable_brcm_irq);
-+EXPORT_SYMBOL(disable_brcm_irq);
-+EXPORT_SYMBOL(request_external_irq);
-+EXPORT_SYMBOL(BcmHalMapInterrupt);
-+
-diff -urN linux-2.6.19/arch/mips/bcm963xx/prom.c linux-2.6.19.new/arch/mips/bcm963xx/prom.c
---- linux-2.6.19/arch/mips/bcm963xx/prom.c 1970-01-01 01:00:00.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/bcm963xx/prom.c 2006-12-16 18:46:31.000000000 +0100
-@@ -0,0 +1,143 @@
-+/*
-+<:copyright-gpl
-+ Copyright 2004 Broadcom Corp. All Rights Reserved.
-+
-+ This program is free software; you can distribute it and/or modify it
-+ under the terms of the GNU General Public License (Version 2) as
-+ published by the Free Software Foundation.
-+
-+ This program is distributed in the hope it will be useful, but WITHOUT
-+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-+ for more details.
-+
-+ You should have received a copy of the GNU General Public License along
-+ with this program; if not, write to the Free Software Foundation, Inc.,
-+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-+:>
-+*/
-+/*
-+ * prom.c: PROM library initialization code.
-+ *
-+ */
-+#include <linux/init.h>
-+#include <linux/mm.h>
-+#include <linux/sched.h>
-+#include <linux/bootmem.h>
-+#include <linux/blkdev.h>
-+#include <asm/addrspace.h>
-+#include <asm/bootinfo.h>
-+#include <asm/cpu.h>
-+#include <asm/time.h>
-+
-+#include <bcm_map_part.h>
-+#include <board.h>
-+#include "boardparms.h"
-+#include "softdsl/AdslCoreDefs.h"
-+
-+
-+//char arcs_cmdline[CL_SIZE] __initdata = {0};
-+/* inv_xde */
-+int boot_loader_type;
-+int prom_argc;
-+char **prom_argv, **prom_envp;
-+
-+extern int do_syslog(int, char *, int);
-+extern void serial_init(void);
-+extern void __init InitNvramInfo( void );
-+extern void kerSysFlashInit( void );
-+extern unsigned long get_nvram_start_addr(void);
-+void __init create_root_nfs_cmdline( char *cmdline );
-+
-+#define MACH_BCM MACH_BCM96348
-+
-+const char *get_system_type(void)
-+{
-+ /*PNVRAM_DATA pNvramData = (PNVRAM_DATA) get_nvram_start_addr();
-+
-+ return( pNvramData->szBoardId );*/
-+ return "brcm63xx";
-+}
-+
-+unsigned long getMemorySize(void)
-+{
-+ unsigned long ulSdramType = BOARD_SDRAM_TYPE;
-+
-+ unsigned long ulSdramSize;
-+
-+ switch( ulSdramType )
-+ {
-+ case BP_MEMORY_16MB_1_CHIP:
-+ case BP_MEMORY_16MB_2_CHIP:
-+ ulSdramSize = 16 * 1024 * 1024;
-+ break;
-+ case BP_MEMORY_32MB_1_CHIP:
-+ case BP_MEMORY_32MB_2_CHIP:
-+ ulSdramSize = 32 * 1024 * 1024;
-+ break;
-+ case BP_MEMORY_64MB_2_CHIP:
-+ ulSdramSize = 64 * 1024 * 1024;
-+ break;
-+ default:
-+ ulSdramSize = 8 * 1024 * 1024;
-+ break;
-+ }
-+ if (boot_loader_type == BOOT_CFE)
-+ return ulSdramSize;
-+ else
-+ // assume that there is one contiguous memory map
-+ return boot_mem_map.map[0].size;
-+}
-+
-+/* --------------------------------------------------------------------------
-+ Name: prom_init
-+ -------------------------------------------------------------------------- */
-+void __init prom_init(void)
-+{
-+ extern ulong r4k_interval;
-+
-+ serial_init();
-+
-+ prom_argc = fw_arg0;
-+ prom_argv = (char **) fw_arg1;
-+ prom_envp = (char **) fw_arg2;
-+
-+ if ((prom_argv > 0x80000000) && (prom_argv < 0x82000000)) {
-+ strncpy(arcs_cmdline, prom_argv[1], CL_SIZE);
-+ }
-+
-+ if (strncmp(arcs_cmdline, "boot_loader=RedBoot", 19) != 0) {
-+ boot_loader_type = BOOT_CFE;
-+ }
-+ else {
-+ boot_loader_type = BOOT_REDBOOT;
-+ }
-+
-+ do_syslog(8, NULL, 8);
-+
-+ printk( "%s prom init\n", get_system_type() );
-+
-+ PERF->IrqMask = 0;
-+
-+ arcs_cmdline[0] = '\0';
-+
-+ if (boot_loader_type == BOOT_CFE)
-+ add_memory_region(0, (getMemorySize() - ADSL_SDRAM_IMAGE_SIZE), BOOT_MEM_RAM);
-+ else
-+ add_memory_region(0, (0x01000000 - ADSL_SDRAM_IMAGE_SIZE), BOOT_MEM_RAM);
-+
-+ mips_machgroup = MACH_GROUP_BRCM;
-+ mips_machtype = MACH_BCM;
-+
-+ BpSetBoardId("96348GW-10");
-+}
-+
-+/* --------------------------------------------------------------------------
-+ Name: prom_free_prom_memory
-+Abstract:
-+ -------------------------------------------------------------------------- */
-+void __init prom_free_prom_memory(void)
-+{
-+
-+}
-+
-diff -urN linux-2.6.19/arch/mips/bcm963xx/ser_init.c linux-2.6.19.new/arch/mips/bcm963xx/ser_init.c
---- linux-2.6.19/arch/mips/bcm963xx/ser_init.c 1970-01-01 01:00:00.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/bcm963xx/ser_init.c 2006-12-16 18:46:31.000000000 +0100
-@@ -0,0 +1,180 @@
-+/*
-+<:copyright-gpl
-+ Copyright 2004 Broadcom Corp. All Rights Reserved.
-+
-+ This program is free software; you can distribute it and/or modify it
-+ under the terms of the GNU General Public License (Version 2) as
-+ published by the Free Software Foundation.
-+
-+ This program is distributed in the hope it will be useful, but WITHOUT
-+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-+ for more details.
-+
-+ You should have received a copy of the GNU General Public License along
-+ with this program; if not, write to the Free Software Foundation, Inc.,
-+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-+:>
-+*/
-+/*
-+ * Broadcom bcm63xx serial port initialization, also prepare for printk
-+ * by registering with console_init
-+ *
-+ */
-+
-+#include <linux/autoconf.h>
-+#include <linux/init.h>
-+#include <linux/interrupt.h>
-+#include <linux/kernel.h>
-+#include <linux/types.h>
-+#include <linux/console.h>
-+#include <linux/sched.h>
-+
-+#include <asm/addrspace.h>
-+#include <asm/irq.h>
-+#include <asm/reboot.h>
-+#include <asm/gdb-stub.h>
-+#include <asm/mc146818rtc.h>
-+
-+#include <bcm_map_part.h>
-+#include <board.h>
-+
-+#define SER63XX_DEFAULT_BAUD 115200
-+#define BD_BCM63XX_TIMER_CLOCK_INPUT (FPERIPH)
-+#define stUart ((volatile Uart * const) UART_BASE)
-+
-+// Transmit interrupts
-+#define TXINT (TXFIFOEMT | TXUNDERR | TXOVFERR)
-+// Receive interrupts
-+#define RXINT (RXFIFONE | RXOVFERR)
-+
-+/* --------------------------------------------------------------------------
-+ Name: serial_init
-+ Purpose: Initalize the UART
-+-------------------------------------------------------------------------- */
-+void __init serial_init(void)
-+{
-+ UINT32 tmpVal = SER63XX_DEFAULT_BAUD;
-+ ULONG clockFreqHz;
-+
-+#if defined(CONFIG_BCM96345)
-+ // Make sure clock is ticking
-+ PERF->blkEnables |= UART_CLK_EN;
-+#endif
-+
-+ /* Dissable channel's receiver and transmitter. */
-+ stUart->control &= ~(BRGEN|TXEN|RXEN);
-+
-+ /*--------------------------------------------------------------------*/
-+ /* Write the table value to the clock select register. */
-+ /* DPullen - this is the equation to use: */
-+ /* value = clockFreqHz / baud / 32-1; */
-+ /* (snmod) Actually you should also take into account any necessary */
-+ /* rounding. Divide by 16, look at lsb, if 0, divide by 2 */
-+ /* and subtract 1. If 1, just divide by 2 */
-+ /*--------------------------------------------------------------------*/
-+ clockFreqHz = BD_BCM63XX_TIMER_CLOCK_INPUT;
-+ tmpVal = (clockFreqHz / tmpVal) / 16;
-+ if( tmpVal & 0x01 )
-+ tmpVal /= 2; //Rounding up, so sub is already accounted for
-+ else
-+ tmpVal = (tmpVal / 2) - 1; // Rounding down so we must sub 1
-+ stUart->baudword = tmpVal;
-+
-+ /* Finally, re-enable the transmitter and receiver. */
-+ stUart->control |= (BRGEN|TXEN|RXEN);
-+
-+ stUart->config = (BITS8SYM | ONESTOP);
-+ // Set the FIFO interrupt depth ... stUart->fifocfg = 0xAA;
-+ stUart->fifoctl = RSTTXFIFOS | RSTRXFIFOS;
-+ stUart->intMask = 0;
-+ stUart->intMask = RXINT | TXINT;
-+}
-+
-+
-+/* prom_putc()
-+ * Output a character to the UART
-+ */
-+void prom_putc(char c)
-+{
-+ /* Wait for Tx uffer to empty */
-+ while (! (READ16(stUart->intStatus) & TXFIFOEMT));
-+ /* Send character */
-+ stUart->Data = c;
-+}
-+
-+/* prom_puts()
-+ * Write a string to the UART
-+ */
-+void prom_puts(const char *s)
-+{
-+ while (*s) {
-+ if (*s == '\n') {
-+ prom_putc('\r');
-+ }
-+ prom_putc(*s++);
-+ }
-+}
-+
-+
-+/* prom_getc_nowait()
-+ * Returns a character from the UART
-+ * Returns -1 if no characters available or corrupted
-+ */
-+int prom_getc_nowait(void)
-+{
-+ uint16 uStatus;
-+ int cData = -1;
-+
-+ uStatus = READ16(stUart->intStatus);
-+
-+ if (uStatus & RXFIFONE) { /* Do we have a character? */
-+ cData = READ16(stUart->Data) & 0xff; /* Read character */
-+ if (uStatus & (RXFRAMERR | RXPARERR)) { /* If we got an error, throw it away */
-+ cData = -1;
-+ }
-+ }
-+
-+ return cData;
-+}
-+
-+/* prom_getc()
-+ * Returns a charcter from the serial port
-+ * Will block until it receives a valid character
-+*/
-+char prom_getc(void)
-+{
-+ int cData = -1;
-+
-+ /* Loop until we get a valid character */
-+ while(cData == -1) {
-+ cData = prom_getc_nowait();
-+ }
-+ return (char) cData;
-+}
-+
-+/* prom_testc()
-+ * Returns 0 if no characters available
-+ */
-+int prom_testc(void)
-+{
-+ uint16 uStatus;
-+
-+ uStatus = READ16(stUart->intStatus);
-+
-+ return (uStatus & RXFIFONE);
-+}
-+
-+#if defined (CONFIG_REMOTE_DEBUG)
-+/* Prevent other code from writing to the serial port */
-+void _putc(char c) { }
-+void _puts(const char *ptr) { }
-+#else
-+/* Low level outputs call prom routines */
-+void _putc(char c) {
-+ prom_putc(c);
-+}
-+void _puts(const char *ptr) {
-+ prom_puts(ptr);
-+}
-+#endif
-diff -urN linux-2.6.19/arch/mips/bcm963xx/setup.c linux-2.6.19.new/arch/mips/bcm963xx/setup.c
---- linux-2.6.19/arch/mips/bcm963xx/setup.c 1970-01-01 01:00:00.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/bcm963xx/setup.c 2006-12-16 18:46:31.000000000 +0100
-@@ -0,0 +1,523 @@
-+/*
-+<:copyright-gpl
-+ Copyright 2002 Broadcom Corp. All Rights Reserved.
-+
-+ This program is free software; you can distribute it and/or modify it
-+ under the terms of the GNU General Public License (Version 2) as
-+ published by the Free Software Foundation.
-+
-+ This program is distributed in the hope it will be useful, but WITHOUT
-+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-+ for more details.
-+
-+ You should have received a copy of the GNU General Public License along
-+ with this program; if not, write to the Free Software Foundation, Inc.,
-+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-+:>
-+*/
-+/*
-+ * Generic setup routines for Broadcom 963xx MIPS boards
-+ */
-+
-+#include <linux/autoconf.h>
-+#include <linux/init.h>
-+#include <linux/interrupt.h>
-+#include <linux/kernel.h>
-+#include <linux/kdev_t.h>
-+#include <linux/types.h>
-+#include <linux/console.h>
-+#include <linux/sched.h>
-+#include <linux/mm.h>
-+#include <linux/slab.h>
-+#include <linux/module.h>
-+#include <linux/pm.h>
-+
-+#include <asm/addrspace.h>
-+#include <asm/bcache.h>
-+#include <asm/irq.h>
-+#include <asm/time.h>
-+#include <asm/reboot.h>
-+#include <asm/gdb-stub.h>
-+
-+extern void brcm_time_init(void);
-+extern unsigned long getMemorySize(void);
-+
-+#if defined(CONFIG_BCM96348) && defined(CONFIG_PCI)
-+#include <linux/pci.h>
-+#include <linux/delay.h>
-+#include <bcm_map_part.h>
-+#include <bcmpci.h>
-+
-+static volatile MpiRegisters * mpi = (MpiRegisters *)(MPI_BASE);
-+#endif
-+
-+/* This function should be in a board specific directory. For now,
-+ * assume that all boards that include this file use a Broadcom chip
-+ * with a soft reset bit in the PLL control register.
-+ */
-+static void brcm_machine_restart(char *command)
-+{
-+ const unsigned long ulSoftReset = 0x00000001;
-+ unsigned long *pulPllCtrl = (unsigned long *) 0xfffe0008;
-+ *pulPllCtrl |= ulSoftReset;
-+}
-+
-+static void brcm_machine_halt(void)
-+{
-+ printk("System halted\n");
-+ while (1);
-+}
-+
-+#if defined(CONFIG_BCM96348) && defined(CONFIG_PCI)
-+
-+static void mpi_SetLocalPciConfigReg(uint32 reg, uint32 value)
-+{
-+ /* write index then value */
-+ mpi->pcicfgcntrl = PCI_CFG_REG_WRITE_EN + reg;;
-+ mpi->pcicfgdata = value;
-+}
-+
-+static uint32 mpi_GetLocalPciConfigReg(uint32 reg)
-+{
-+ /* write index then get value */
-+ mpi->pcicfgcntrl = PCI_CFG_REG_WRITE_EN + reg;;
-+ return mpi->pcicfgdata;
-+}
-+
-+/*
-+ * mpi_ResetPcCard: Set/Reset the PcCard
-+ */
-+static void mpi_ResetPcCard(int cardtype, BOOL bReset)
-+{
-+ if (cardtype == MPI_CARDTYPE_NONE) {
-+ return;
-+ }
-+
-+ if (cardtype == MPI_CARDTYPE_CARDBUS) {
-+ bReset = ! bReset;
-+ }
-+
-+ if (bReset) {
-+ mpi->pcmcia_cntl1 = (mpi->pcmcia_cntl1 & ~PCCARD_CARD_RESET);
-+ } else {
-+ mpi->pcmcia_cntl1 = (mpi->pcmcia_cntl1 | PCCARD_CARD_RESET);
-+ }
-+}
-+
-+/*
-+ * mpi_ConfigCs: Configure an MPI/EBI chip select
-+ */
-+static void mpi_ConfigCs(uint32 cs, uint32 base, uint32 size, uint32 flags)
-+{
-+ mpi->cs[cs].base = ((base & 0x1FFFFFFF) | size);
-+ mpi->cs[cs].config = flags;
-+}
-+
-+/*
-+ * mpi_InitPcmciaSpace
-+ */
-+static void mpi_InitPcmciaSpace(void)
-+{
-+ // ChipSelect 4 controls PCMCIA Memory accesses
-+ mpi_ConfigCs(PCMCIA_COMMON_BASE, pcmciaMem, EBI_SIZE_1M, (EBI_WORD_WIDE|EBI_ENABLE));
-+ // ChipSelect 5 controls PCMCIA Attribute accesses
-+ mpi_ConfigCs(PCMCIA_ATTRIBUTE_BASE, pcmciaAttr, EBI_SIZE_1M, (EBI_WORD_WIDE|EBI_ENABLE));
-+ // ChipSelect 6 controls PCMCIA I/O accesses
-+ mpi_ConfigCs(PCMCIA_IO_BASE, pcmciaIo, EBI_SIZE_64K, (EBI_WORD_WIDE|EBI_ENABLE));
-+
-+ mpi->pcmcia_cntl2 = ((PCMCIA_ATTR_ACTIVE << RW_ACTIVE_CNT_BIT) |
-+ (PCMCIA_ATTR_INACTIVE << INACTIVE_CNT_BIT) |
-+ (PCMCIA_ATTR_CE_SETUP << CE_SETUP_CNT_BIT) |
-+ (PCMCIA_ATTR_CE_HOLD << CE_HOLD_CNT_BIT));
-+
-+ mpi->pcmcia_cntl2 |= (PCMCIA_HALFWORD_EN | PCMCIA_BYTESWAP_DIS);
-+}
-+
-+/*
-+ * cardtype_vcc_detect: PC Card's card detect and voltage sense connection
-+ *
-+ * CD1#/ CD2#/ VS1#/ VS2#/ Card Initial Vcc
-+ * CCD1# CCD2# CVS1 CVS2 Type
-+ *
-+ * GND GND open open 16-bit 5 vdc
-+ *
-+ * GND GND GND open 16-bit 3.3 vdc
-+ *
-+ * GND GND open GND 16-bit x.x vdc
-+ *
-+ * GND GND GND GND 16-bit 3.3 & x.x vdc
-+ *
-+ *====================================================================
-+ *
-+ * CVS1 GND CCD1# open CardBus 3.3 vdc
-+ *
-+ * GND CVS2 open CCD2# CardBus x.x vdc
-+ *
-+ * GND CVS1 CCD2# open CardBus y.y vdc
-+ *
-+ * GND CVS2 GND CCD2# CardBus 3.3 & x.x vdc
-+ *
-+ * CVS2 GND open CCD1# CardBus x.x & y.y vdc
-+ *
-+ * GND CVS1 CCD2# open CardBus 3.3, x.x & y.y vdc
-+ *
-+ */
-+static int cardtype_vcc_detect(void)
-+{
-+ uint32 data32;
-+ int cardtype;
-+
-+ cardtype = MPI_CARDTYPE_NONE;
-+ mpi->pcmcia_cntl1 = 0x0000A000; // Turn on the output enables and drive
-+ // the CVS pins to 0.
-+ data32 = mpi->pcmcia_cntl1;
-+ switch (data32 & 0x00000003) // Test CD1# and CD2#, see if card is plugged in.
-+ {
-+ case 0x00000003: // No Card is in the slot.
-+ printk("mpi: No Card is in the PCMCIA slot\n");
-+ break;
-+
-+ case 0x00000002: // Partial insertion, No CD2#.
-+ printk("mpi: Card in the PCMCIA slot partial insertion, no CD2 signal\n");
-+ break;
-+
-+ case 0x00000001: // Partial insertion, No CD1#.
-+ printk("mpi: Card in the PCMCIA slot partial insertion, no CD1 signal\n");
-+ break;
-+
-+ case 0x00000000:
-+ mpi->pcmcia_cntl1 = 0x0000A0C0; // Turn off the CVS output enables and
-+ // float the CVS pins.
-+ mdelay(1);
-+ data32 = mpi->pcmcia_cntl1;
-+ // Read the Register.
-+ switch (data32 & 0x0000000C) // See what is on the CVS pins.
-+ {
-+ case 0x00000000: // CVS1 and CVS2 are tied to ground, only 1 option.
-+ printk("mpi: Detected 3.3 & x.x 16-bit PCMCIA card\n");
-+ cardtype = MPI_CARDTYPE_PCMCIA;
-+ break;
-+
-+ case 0x00000004: // CVS1 is open or tied to CCD1/CCD2 and CVS2 is tied to ground.
-+ // 2 valid voltage options.
-+ switch (data32 & 0x00000003) // Test the values of CCD1 and CCD2.
-+ {
-+ case 0x00000003: // CCD1 and CCD2 are tied to 1 of the CVS pins.
-+ // This is not a valid combination.
-+ printk("mpi: Unknown card plugged into slot\n");
-+ break;
-+
-+ case 0x00000002: // CCD2 is tied to either CVS1 or CVS2.
-+ mpi->pcmcia_cntl1 = 0x0000A080; // Drive CVS1 to a 0.
-+ mdelay(1);
-+ data32 = mpi->pcmcia_cntl1;
-+ if (data32 & 0x00000002) { // CCD2 is tied to CVS2, not valid.
-+ printk("mpi: Unknown card plugged into slot\n");
-+ } else { // CCD2 is tied to CVS1.
-+ printk("mpi: Detected 3.3, x.x and y.y Cardbus card\n");
-+ cardtype = MPI_CARDTYPE_CARDBUS;
-+ }
-+ break;
-+
-+ case 0x00000001: // CCD1 is tied to either CVS1 or CVS2.
-+ // This is not a valid combination.
-+ printk("mpi: Unknown card plugged into slot\n");
-+ break;
-+
-+ case 0x00000000: // CCD1 and CCD2 are tied to ground.
-+ printk("mpi: Detected x.x vdc 16-bit PCMCIA card\n");
-+ cardtype = MPI_CARDTYPE_PCMCIA;
-+ break;
-+ }
-+ break;
-+
-+ case 0x00000008: // CVS2 is open or tied to CCD1/CCD2 and CVS1 is tied to ground.
-+ // 2 valid voltage options.
-+ switch (data32 & 0x00000003) // Test the values of CCD1 and CCD2.
-+ {
-+ case 0x00000003: // CCD1 and CCD2 are tied to 1 of the CVS pins.
-+ // This is not a valid combination.
-+ printk("mpi: Unknown card plugged into slot\n");
-+ break;
-+
-+ case 0x00000002: // CCD2 is tied to either CVS1 or CVS2.
-+ mpi->pcmcia_cntl1 = 0x0000A040; // Drive CVS2 to a 0.
-+ mdelay(1);
-+ data32 = mpi->pcmcia_cntl1;
-+ if (data32 & 0x00000002) { // CCD2 is tied to CVS1, not valid.
-+ printk("mpi: Unknown card plugged into slot\n");
-+ } else {// CCD2 is tied to CVS2.
-+ printk("mpi: Detected 3.3 and x.x Cardbus card\n");
-+ cardtype = MPI_CARDTYPE_CARDBUS;
-+ }
-+ break;
-+
-+ case 0x00000001: // CCD1 is tied to either CVS1 or CVS2.
-+ // This is not a valid combination.
-+ printk("mpi: Unknown card plugged into slot\n");
-+ break;
-+
-+ case 0x00000000: // CCD1 and CCD2 are tied to ground.
-+ cardtype = MPI_CARDTYPE_PCMCIA;
-+ printk("mpi: Detected 3.3 vdc 16-bit PCMCIA card\n");
-+ break;
-+ }
-+ break;
-+
-+ case 0x0000000C: // CVS1 and CVS2 are open or tied to CCD1/CCD2.
-+ // 5 valid voltage options.
-+
-+ switch (data32 & 0x00000003) // Test the values of CCD1 and CCD2.
-+ {
-+ case 0x00000003: // CCD1 and CCD2 are tied to 1 of the CVS pins.
-+ // This is not a valid combination.
-+ printk("mpi: Unknown card plugged into slot\n");
-+ break;
-+
-+ case 0x00000002: // CCD2 is tied to either CVS1 or CVS2.
-+ // CCD1 is tied to ground.
-+ mpi->pcmcia_cntl1 = 0x0000A040; // Drive CVS2 to a 0.
-+ mdelay(1);
-+ data32 = mpi->pcmcia_cntl1;
-+ if (data32 & 0x00000002) { // CCD2 is tied to CVS1.
-+ printk("mpi: Detected y.y vdc Cardbus card\n");
-+ } else { // CCD2 is tied to CVS2.
-+ printk("mpi: Detected x.x vdc Cardbus card\n");
-+ }
-+ cardtype = MPI_CARDTYPE_CARDBUS;
-+ break;
-+
-+ case 0x00000001: // CCD1 is tied to either CVS1 or CVS2.
-+ // CCD2 is tied to ground.
-+
-+ mpi->pcmcia_cntl1 = 0x0000A040; // Drive CVS2 to a 0.
-+ mdelay(1);
-+ data32 = mpi->pcmcia_cntl1;
-+ if (data32 & 0x00000001) {// CCD1 is tied to CVS1.
-+ printk("mpi: Detected 3.3 vdc Cardbus card\n");
-+ } else { // CCD1 is tied to CVS2.
-+ printk("mpi: Detected x.x and y.y Cardbus card\n");
-+ }
-+ cardtype = MPI_CARDTYPE_CARDBUS;
-+ break;
-+
-+ case 0x00000000: // CCD1 and CCD2 are tied to ground.
-+ cardtype = MPI_CARDTYPE_PCMCIA;
-+ printk("mpi: Detected 5 vdc 16-bit PCMCIA card\n");
-+ break;
-+ }
-+ break;
-+
-+ default:
-+ printk("mpi: Unknown card plugged into slot\n");
-+ break;
-+
-+ }
-+ }
-+ return cardtype;
-+}
-+
-+/*
-+ * mpi_DetectPcCard: Detect the plugged in PC-Card
-+ * Return: < 0 => Unknown card detected
-+ * 0 => No card detected
-+ * 1 => 16-bit card detected
-+ * 2 => 32-bit CardBus card detected
-+ */
-+static int mpi_DetectPcCard(void)
-+{
-+ int cardtype;
-+
-+ cardtype = cardtype_vcc_detect();
-+ switch(cardtype) {
-+ case MPI_CARDTYPE_PCMCIA:
-+ mpi->pcmcia_cntl1 &= ~0x0000e000; // disable enable bits
-+ //mpi->pcmcia_cntl1 = (mpi->pcmcia_cntl1 & ~PCCARD_CARD_RESET);
-+ mpi->pcmcia_cntl1 |= (PCMCIA_ENABLE | PCMCIA_GPIO_ENABLE);
-+ mpi_InitPcmciaSpace();
-+ mpi_ResetPcCard(cardtype, FALSE);
-+ // Hold card in reset for 10ms
-+ mdelay(10);
-+ mpi_ResetPcCard(cardtype, TRUE);
-+ // Let card come out of reset
-+ mdelay(100);
-+ break;
-+ case MPI_CARDTYPE_CARDBUS:
-+ // 8 => CardBus Enable
-+ // 1 => PCI Slot Number
-+ // C => Float VS1 & VS2
-+ mpi->pcmcia_cntl1 = (mpi->pcmcia_cntl1 & 0xFFFF0000) |
-+ CARDBUS_ENABLE |
-+ (CARDBUS_SLOT << 8)|
-+ VS2_OEN |
-+ VS1_OEN;
-+ /* access to this memory window will be to/from CardBus */
-+ mpi->l2pmremap1 |= CARDBUS_MEM;
-+
-+ // Need to reset the Cardbus Card. There's no CardManager to do this,
-+ // and we need to be ready for PCI configuration.
-+ mpi_ResetPcCard(cardtype, FALSE);
-+ // Hold card in reset for 10ms
-+ mdelay(10);
-+ mpi_ResetPcCard(cardtype, TRUE);
-+ // Let card come out of reset
-+ mdelay(100);
-+ break;
-+ default:
-+ break;
-+ }
-+ return cardtype;
-+}
-+
-+static int mpi_init(void)
-+{
-+ unsigned long data;
-+ unsigned int chipid;
-+ unsigned int chiprev;
-+ unsigned int sdramsize;
-+
-+ chipid = (PERF->RevID & 0xFFFF0000) >> 16;
-+ chiprev = (PERF->RevID & 0xFF);
-+ sdramsize = getMemorySize();
-+ /*
-+ * Init the pci interface
-+ */
-+ data = GPIO->GPIOMode; // GPIO mode register
-+ data |= GROUP2_PCI | GROUP1_MII_PCCARD; // PCI internal arbiter + Cardbus
-+ GPIO->GPIOMode = data; // PCI internal arbiter
-+
-+ /*
-+ * In the BCM6348 CardBus support is defaulted to Slot 0
-+ * because there is no external IDSEL for CardBus. To disable
-+ * the CardBus and allow a standard PCI card in Slot 0
-+ * set the cbus_idsel field to 0x1f.
-+ */
-+ /*
-+ uData = mpi->pcmcia_cntl1;
-+ uData |= CARDBUS_IDSEL;
-+ mpi->pcmcia_cntl1 = uData;
-+ */
-+ // Setup PCI I/O Window range. Give 64K to PCI I/O
-+ mpi->l2piorange = ~(BCM_PCI_IO_SIZE_64KB-1);
-+ // UBUS to PCI I/O base address
-+ mpi->l2piobase = BCM_PCI_IO_BASE & BCM_PCI_ADDR_MASK;
-+ // UBUS to PCI I/O Window remap
-+ mpi->l2pioremap = (BCM_PCI_IO_BASE | MEM_WINDOW_EN);
-+
-+ // enable PCI related GPIO pins and data swap between system and PCI bus
-+ mpi->locbuscntrl = (EN_PCI_GPIO | DIR_U2P_NOSWAP);
-+
-+ /* Enable 6348 BusMaster and Memory access mode */
-+ data = mpi_GetLocalPciConfigReg(PCI_COMMAND);
-+ data |= (PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
-+ mpi_SetLocalPciConfigReg(PCI_COMMAND, data);
-+
-+ /* Configure two 16 MByte PCI to System memory regions. */
-+ /* These memory regions are used when PCI device is a bus master */
-+ /* Accesses to the SDRAM from PCI bus will be "byte swapped" for this region */
-+ mpi_SetLocalPciConfigReg(PCI_BASE_ADDRESS_3, BCM_HOST_MEM_SPACE1);
-+ mpi->sp0remap = 0x0;
-+
-+ /* Accesses to the SDRAM from PCI bus will not be "byte swapped" for this region */
-+ mpi_SetLocalPciConfigReg(PCI_BASE_ADDRESS_4, BCM_HOST_MEM_SPACE2);
-+ mpi->sp1remap = 0x0;
-+ mpi->pcimodesel |= (PCI_BAR2_NOSWAP | 0x40);
-+
-+ if ((chipid == 0x6348) && (chiprev == 0xb0)) {
-+ mpi->sp0range = ~(sdramsize-1);
-+ mpi->sp1range = ~(sdramsize-1);
-+ }
-+ /*
-+ * Change 6348 PCI Cfg Reg. offset 0x40 to PCI memory read retry count infinity
-+ * by set 0 in bit 8~15. This resolve read Bcm4306 srom return 0xffff in
-+ * first read.
-+ */
-+ data = mpi_GetLocalPciConfigReg(BRCM_PCI_CONFIG_TIMER);
-+ data &= ~BRCM_PCI_CONFIG_TIMER_RETRY_MASK;
-+ data |= 0x00000080;
-+ mpi_SetLocalPciConfigReg(BRCM_PCI_CONFIG_TIMER, data);
-+
-+ /* enable pci interrupt */
-+ mpi->locintstat |= (EXT_PCI_INT << 16);
-+
-+ mpi_DetectPcCard();
-+
-+ ioport_resource.start = BCM_PCI_IO_BASE;
-+ ioport_resource.end = BCM_PCI_IO_BASE + BCM_PCI_IO_SIZE_64KB;
-+
-+#if defined(CONFIG_USB)
-+ PERF->blkEnables |= USBH_CLK_EN;
-+ mdelay(100);
-+ *USBH_NON_OHCI = NON_OHCI_BYTE_SWAP;
-+#endif
-+
-+ return 0;
-+}
-+#endif
-+
-+static int __init brcm63xx_setup(void)
-+{
-+ extern int panic_timeout;
-+
-+ _machine_restart = brcm_machine_restart;
-+ _machine_halt = brcm_machine_halt;
-+ pm_power_off = brcm_machine_halt;
-+
-+ board_time_init = brcm_time_init;
-+
-+ panic_timeout = 5;
-+
-+#if defined(CONFIG_BCM96348) && defined(CONFIG_PCI)
-+ /* mpi initialization */
-+ mpi_init();
-+#endif
-+ return 0;
-+}
-+
-+void __init plat_mem_setup(void)
-+{
-+ brcm63xx_setup();
-+}
-+
-+/***************************************************************************
-+ * C++ New and delete operator functions
-+ ***************************************************************************/
-+
-+/* void *operator new(unsigned int sz) */
-+void *_Znwj(unsigned int sz)
-+{
-+ return( kmalloc(sz, GFP_KERNEL) );
-+}
-+
-+/* void *operator new[](unsigned int sz)*/
-+void *_Znaj(unsigned int sz)
-+{
-+ return( kmalloc(sz, GFP_KERNEL) );
-+}
-+
-+/* placement new operator */
-+/* void *operator new (unsigned int size, void *ptr) */
-+void *ZnwjPv(unsigned int size, void *ptr)
-+{
-+ return ptr;
-+}
-+
-+/* void operator delete(void *m) */
-+void _ZdlPv(void *m)
-+{
-+ kfree(m);
-+}
-+
-+/* void operator delete[](void *m) */
-+void _ZdaPv(void *m)
-+{
-+ kfree(m);
-+}
-+
-+EXPORT_SYMBOL(_Znwj);
-+EXPORT_SYMBOL(_Znaj);
-+EXPORT_SYMBOL(ZnwjPv);
-+EXPORT_SYMBOL(_ZdlPv);
-+EXPORT_SYMBOL(_ZdaPv);
-+
-diff -urN linux-2.6.19/arch/mips/bcm963xx/softdsl/AdslCoreDefs.h linux-2.6.19.new/arch/mips/bcm963xx/softdsl/AdslCoreDefs.h
---- linux-2.6.19/arch/mips/bcm963xx/softdsl/AdslCoreDefs.h 1970-01-01 01:00:00.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/bcm963xx/softdsl/AdslCoreDefs.h 2006-12-16 18:46:31.000000000 +0100
-@@ -0,0 +1,2 @@
-+#define ADSL_SDRAM_IMAGE_SIZE (384*1024)
-+
-diff -urN linux-2.6.19/arch/mips/bcm963xx/time.c linux-2.6.19.new/arch/mips/bcm963xx/time.c
---- linux-2.6.19/arch/mips/bcm963xx/time.c 1970-01-01 01:00:00.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/bcm963xx/time.c 2006-12-16 18:46:31.000000000 +0100
-@@ -0,0 +1,114 @@
-+/*
-+<:copyright-gpl
-+ Copyright 2004 Broadcom Corp. All Rights Reserved.
-+
-+ This program is free software; you can distribute it and/or modify it
-+ under the terms of the GNU General Public License (Version 2) as
-+ published by the Free Software Foundation.
-+
-+ This program is distributed in the hope it will be useful, but WITHOUT
-+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-+ for more details.
-+
-+ You should have received a copy of the GNU General Public License along
-+ with this program; if not, write to the Free Software Foundation, Inc.,
-+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-+:>
-+*/
-+/*
-+ * Setup time for Broadcom 963xx MIPS boards
-+ */
-+
-+#include <linux/autoconf.h>
-+#include <linux/init.h>
-+#include <linux/kernel_stat.h>
-+#include <linux/sched.h>
-+#include <linux/spinlock.h>
-+#include <linux/interrupt.h>
-+#include <linux/module.h>
-+#include <linux/time.h>
-+#include <linux/timex.h>
-+
-+#include <asm/mipsregs.h>
-+#include <asm/ptrace.h>
-+#include <asm/div64.h>
-+#include <asm/time.h>
-+
-+#include <bcm_map_part.h>
-+#include <bcm_intr.h>
-+
-+static unsigned long r4k_offset; /* Amount to increment compare reg each time */
-+static unsigned long r4k_cur; /* What counter should be at next timer irq */
-+
-+/* *********************************************************************
-+ * calculateCpuSpeed()
-+ * Calculate the BCM6348 CPU speed by reading the PLL strap register
-+ * and applying the following formula:
-+ * cpu_clk = (.25 * 64MHz freq) * (N1 + 1) * (N2 + 2) / (M1_CPU + 1)
-+ * Input parameters:
-+ * none
-+ * Return value:
-+ * none
-+ ********************************************************************* */
-+
-+static inline unsigned long __init calculateCpuSpeed(void)
-+{
-+ UINT32 pllStrap = PERF->PllStrap;
-+ int n1 = (pllStrap & PLL_N1_MASK) >> PLL_N1_SHFT;
-+ int n2 = (pllStrap & PLL_N2_MASK) >> PLL_N2_SHFT;
-+ int m1cpu = (pllStrap & PLL_M1_CPU_MASK) >> PLL_M1_CPU_SHFT;
-+
-+ return (16 * (n1 + 1) * (n2 + 2) / (m1cpu + 1)) * 1000000;
-+}
-+
-+
-+static inline unsigned long __init cal_r4koff(void)
-+{
-+ mips_hpt_frequency = calculateCpuSpeed() / 2;
-+ return (mips_hpt_frequency / HZ);
-+}
-+
-+
-+/*
-+ * There are a lot of conceptually broken versions of the MIPS timer interrupt
-+ * handler floating around. This one is rather different, but the algorithm
-+ * is provably more robust.
-+ */
-+irqreturn_t brcm_timer_interrupt(struct pt_regs *regs)
-+{
-+ int irq = MIPS_TIMER_INT;
-+
-+ irq_enter();
-+ kstat_this_cpu.irqs[irq]++;
-+
-+ timer_interrupt(irq, regs);
-+ irq_exit();
-+ return IRQ_HANDLED;
-+}
-+
-+
-+void __init brcm_time_init(void)
-+{
-+ unsigned int est_freq, flags;
-+ local_irq_save(flags);
-+
-+ printk("calculating r4koff... ");
-+ r4k_offset = cal_r4koff();
-+ printk("%08lx(%d)\n", r4k_offset, (int)r4k_offset);
-+
-+ est_freq = 2 * r4k_offset * HZ;
-+ est_freq += 5000; /* round */
-+ est_freq -= est_freq % 10000;
-+ printk("CPU frequency %d.%02d MHz\n", est_freq / 1000000,
-+ (est_freq % 1000000) * 100 / 1000000);
-+ local_irq_restore(flags);
-+}
-+
-+
-+void __init plat_timer_setup(struct irqaction *irq)
-+{
-+ r4k_cur = (read_c0_count() + r4k_offset);
-+ write_c0_compare(r4k_cur);
-+ set_c0_status(IE_IRQ5);
-+}
-diff -urN linux-2.6.19/arch/mips/kernel/cpu-probe.c linux-2.6.19.new/arch/mips/kernel/cpu-probe.c
---- linux-2.6.19/arch/mips/kernel/cpu-probe.c 2006-11-29 22:57:37.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/kernel/cpu-probe.c 2006-12-16 18:46:31.000000000 +0100
-@@ -602,6 +602,25 @@
- return;
- }
-
-+static inline void cpu_probe_broadcom(struct cpuinfo_mips *c)
-+{
-+ decode_configs(c);
-+ switch (c->processor_id & 0xff00) {
-+ case PRID_IMP_BCM6338:
-+ c->cputype = CPU_BCM6338;
-+ break;
-+ case PRID_IMP_BCM6345:
-+ c->cputype = CPU_BCM6345;
-+ break;
-+ case PRID_IMP_BCM6348:
-+ c->cputype = CPU_BCM6348;
-+ break;
-+ default:
-+ c->cputype = CPU_UNKNOWN;
-+ break;
-+ }
-+}
-+
- static inline void cpu_probe_mips(struct cpuinfo_mips *c)
- {
- decode_configs(c);
-@@ -736,6 +755,9 @@
- case PRID_COMP_LEGACY:
- cpu_probe_legacy(c);
- break;
-+ case PRID_COMP_BROADCOM:
-+ cpu_probe_broadcom(c);
-+ break;
- case PRID_COMP_MIPS:
- cpu_probe_mips(c);
- break;
-diff -urN linux-2.6.19/arch/mips/kernel/proc.c linux-2.6.19.new/arch/mips/kernel/proc.c
---- linux-2.6.19/arch/mips/kernel/proc.c 2006-11-29 22:57:37.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/kernel/proc.c 2006-12-16 18:46:31.000000000 +0100
-@@ -84,6 +84,9 @@
- [CPU_VR4181A] = "NEC VR4181A",
- [CPU_SR71000] = "Sandcraft SR71000",
- [CPU_PR4450] = "Philips PR4450",
-+ [CPU_BCM6338] = "BCM6338",
-+ [CPU_BCM6345] = "BCM6345",
-+ [CPU_BCM6348] = "BCM6348",
- };
-
-
-diff -urN linux-2.6.19/arch/mips/mm/c-r4k.c linux-2.6.19.new/arch/mips/mm/c-r4k.c
---- linux-2.6.19/arch/mips/mm/c-r4k.c 2006-11-29 22:57:37.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/mm/c-r4k.c 2006-12-16 18:46:31.000000000 +0100
-@@ -852,6 +852,13 @@
- if (!(config & MIPS_CONF_M))
- panic("Don't know how to probe P-caches on this cpu.");
-
-+ if (c->cputype == CPU_BCM6338 || c->cputype == CPU_BCM6345 || c->cputype == CPU_BCM6348)
-+ {
-+ printk("brcm mips: enabling icache and dcache...\n");
-+ /* Enable caches */
-+ write_c0_diag(read_c0_diag() | 0xC0000000);
-+ }
-+
- /*
- * So we seem to be a MIPS32 or MIPS64 CPU
- * So let's probe the I-cache ...
-diff -urN linux-2.6.19/arch/mips/mm/tlbex.c linux-2.6.19.new/arch/mips/mm/tlbex.c
---- linux-2.6.19/arch/mips/mm/tlbex.c 2006-11-29 22:57:37.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/mm/tlbex.c 2006-12-16 18:46:31.000000000 +0100
-@@ -880,6 +880,9 @@
- case CPU_4KSC:
- case CPU_20KC:
- case CPU_25KF:
-+ case CPU_BCM6338:
-+ case CPU_BCM6345:
-+ case CPU_BCM6348:
- tlbw(p);
- break;
-
-diff -urN linux-2.6.19/arch/mips/pci/Makefile linux-2.6.19.new/arch/mips/pci/Makefile
---- linux-2.6.19/arch/mips/pci/Makefile 2006-11-29 22:57:37.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/pci/Makefile 2006-12-16 18:48:18.000000000 +0100
-@@ -17,6 +17,7 @@
- obj-$(CONFIG_PCI_VR41XX) += ops-vr41xx.o pci-vr41xx.o
- obj-$(CONFIG_NEC_CMBVR4133) += fixup-vr4133.o
- obj-$(CONFIG_MARKEINS) += ops-emma2rh.o pci-emma2rh.o fixup-emma2rh.o
-+obj-$(CONFIG_BCM_PCI) += fixup-bcm96348.o pci-bcm96348.o ops-bcm96348.o
-
- #
- # These are still pretty much in the old state, watch, go blind.
-diff -urN linux-2.6.19/arch/mips/pci/fixup-bcm96348.c linux-2.6.19.new/arch/mips/pci/fixup-bcm96348.c
---- linux-2.6.19/arch/mips/pci/fixup-bcm96348.c 1970-01-01 01:00:00.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/pci/fixup-bcm96348.c 2006-12-16 18:46:31.000000000 +0100
-@@ -0,0 +1,93 @@
-+/*
-+<:copyright-gpl
-+ Copyright 2002 Broadcom Corp. All Rights Reserved.
-+
-+ This program is free software; you can distribute it and/or modify it
-+ under the terms of the GNU General Public License (Version 2) as
-+ published by the Free Software Foundation.
-+
-+ This program is distributed in the hope it will be useful, but WITHOUT
-+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-+ for more details.
-+
-+ You should have received a copy of the GNU General Public License along
-+ with this program; if not, write to the Free Software Foundation, Inc.,
-+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-+:>
-+*/
-+#include <linux/init.h>
-+#include <linux/types.h>
-+#include <linux/pci.h>
-+
-+#include <bcmpci.h>
-+#include <bcm_intr.h>
-+#include <bcm_map_part.h>
-+
-+static volatile MpiRegisters * mpi = (MpiRegisters *)(MPI_BASE);
-+
-+static char irq_tab_bcm96348[] __initdata = {
-+ [0] = INTERRUPT_ID_MPI,
-+ [1] = INTERRUPT_ID_MPI,
-+#if defined(CONFIG_USB)
-+ [USB_HOST_SLOT] = INTERRUPT_ID_USBH
-+#endif
-+};
-+
-+int __init pcibios_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
-+{
-+ return irq_tab_bcm96348[slot];
-+}
-+
-+static void bcm96348_fixup(struct pci_dev *dev)
-+{
-+ uint32 memaddr;
-+ uint32 size;
-+
-+ memaddr = pci_resource_start(dev, 0);
-+ size = pci_resource_len(dev, 0);
-+
-+ switch (PCI_SLOT(dev->devfn)) {
-+ case 0:
-+ // UBUS to PCI address range
-+ // Memory Window 1. Mask determines which bits are decoded.
-+ mpi->l2pmrange1 = ~(size-1);
-+ // UBUS to PCI Memory base address. This is akin to the ChipSelect base
-+ // register.
-+ mpi->l2pmbase1 = memaddr & BCM_PCI_ADDR_MASK;
-+ // UBUS to PCI Remap Address. Replaces the masked address bits in the
-+ // range register with this setting.
-+ // Also, enable direct I/O and direct Memory accesses
-+ mpi->l2pmremap1 = (memaddr | MEM_WINDOW_EN);
-+ break;
-+
-+ case 1:
-+ // Memory Window 2
-+ mpi->l2pmrange2 = ~(size-1);
-+ // UBUS to PCI Memory base address.
-+ mpi->l2pmbase2 = memaddr & BCM_PCI_ADDR_MASK;
-+ // UBUS to PCI Remap Address
-+ mpi->l2pmremap2 = (memaddr | MEM_WINDOW_EN);
-+ break;
-+
-+#if defined(CONFIG_USB)
-+ case USB_HOST_SLOT:
-+ dev->resource[0].start = USB_HOST_BASE;
-+ dev->resource[0].end = USB_HOST_BASE+USB_BAR0_MEM_SIZE-1;
-+ break;
-+#endif
-+ }
-+}
-+
-+int pcibios_plat_dev_init(struct pci_dev *dev)
-+{
-+ return 0;
-+}
-+
-+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, PCI_ANY_ID,
-+ bcm96348_fixup);
-+
-+/*struct pci_fixup pcibios_fixups[] = {
-+ { PCI_FIXUP_FINAL, PCI_ANY_ID, PCI_ANY_ID, bcm96348_fixup },
-+ {0}
-+};*/
-diff -urN linux-2.6.19/arch/mips/pci/ops-bcm96348.c linux-2.6.19.new/arch/mips/pci/ops-bcm96348.c
---- linux-2.6.19/arch/mips/pci/ops-bcm96348.c 1970-01-01 01:00:00.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/pci/ops-bcm96348.c 2006-12-16 18:46:31.000000000 +0100
-@@ -0,0 +1,276 @@
-+/*
-+<:copyright-gpl
-+ Copyright 2002 Broadcom Corp. All Rights Reserved.
-+
-+ This program is free software; you can distribute it and/or modify it
-+ under the terms of the GNU General Public License (Version 2) as
-+ published by the Free Software Foundation.
-+
-+ This program is distributed in the hope it will be useful, but WITHOUT
-+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-+ for more details.
-+
-+ You should have received a copy of the GNU General Public License along
-+ with this program; if not, write to the Free Software Foundation, Inc.,
-+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-+:>
-+*/
-+#include <linux/types.h>
-+#include <linux/pci.h>
-+#include <linux/kernel.h>
-+#include <linux/init.h>
-+#include <asm/addrspace.h>
-+
-+#include <bcm_intr.h>
-+#include <bcm_map_part.h>
-+#include <bcmpci.h>
-+
-+#include <linux/delay.h>
-+
-+#if defined(CONFIG_USB)
-+#if 0
-+#define DPRINT(x...) printk(x)
-+#else
-+#define DPRINT(x...)
-+#endif
-+
-+static int
-+pci63xx_int_read(unsigned int devfn, int where, u32 * value, int size);
-+static int
-+pci63xx_int_write(unsigned int devfn, int where, u32 * value, int size);
-+
-+static bool usb_mem_size_rd = FALSE;
-+static uint32 usb_mem_base = 0;
-+static uint32 usb_cfg_space_cmd_reg = 0;
-+#endif
-+static bool pci_mem_size_rd = FALSE;
-+
-+static volatile MpiRegisters * mpi = (MpiRegisters *)(MPI_BASE);
-+
-+static void mpi_SetupPciConfigAccess(uint32 addr)
-+{
-+ mpi->l2pcfgctl = (DIR_CFG_SEL | DIR_CFG_USEREG | addr) & ~CONFIG_TYPE;
-+}
-+
-+static void mpi_ClearPciConfigAccess(void)
-+{
-+ mpi->l2pcfgctl = 0x00000000;
-+}
-+
-+#if defined(CONFIG_USB)
-+/* --------------------------------------------------------------------------
-+ Name: pci63xx_int_write
-+Abstract: PCI Config write on internal device(s)
-+ -------------------------------------------------------------------------- */
-+static int
-+pci63xx_int_write(unsigned int devfn, int where, u32 * value, int size)
-+{
-+ if (PCI_SLOT(devfn) != USB_HOST_SLOT) {
-+ return PCIBIOS_SUCCESSFUL;
-+ }
-+
-+ switch (size) {
-+ case 1:
-+ DPRINT("W => Slot: %d Where: %2X Len: %d Data: %02X\n",
-+ PCI_SLOT(devfn), where, size, *value);
-+ break;
-+ case 2:
-+ DPRINT("W => Slot: %d Where: %2X Len: %d Data: %04X\n",
-+ PCI_SLOT(devfn), where, size, *value);
-+ switch (where) {
-+ case PCI_COMMAND:
-+ usb_cfg_space_cmd_reg = *value;
-+ break;
-+ default:
-+ break;
-+ }
-+ break;
-+ case 4:
-+ DPRINT("W => Slot: %d Where: %2X Len: %d Data: %08lX\n",
-+ PCI_SLOT(devfn), where, size, *value);
-+ switch (where) {
-+ case PCI_BASE_ADDRESS_0:
-+ if (*value == 0xffffffff) {
-+ usb_mem_size_rd = TRUE;
-+ } else {
-+ usb_mem_base = *value;
-+ }
-+ break;
-+ default:
-+ break;
-+ }
-+ break;
-+ default:
-+ break;
-+ }
-+
-+ return PCIBIOS_SUCCESSFUL;
-+}
-+
-+/* --------------------------------------------------------------------------
-+ Name: pci63xx_int_read
-+Abstract: PCI Config read on internal device(s)
-+ -------------------------------------------------------------------------- */
-+static int
-+pci63xx_int_read(unsigned int devfn, int where, u32 * value, int size)
-+{
-+ uint32 retValue = 0xFFFFFFFF;
-+
-+ if (PCI_SLOT(devfn) != USB_HOST_SLOT) {
-+ return PCIBIOS_SUCCESSFUL;
-+ }
-+
-+ // For now, this is specific to the USB Host controller. We can
-+ // make it more general if we have to...
-+ // Emulate PCI Config accesses
-+ switch (where) {
-+ case PCI_VENDOR_ID:
-+ case PCI_DEVICE_ID:
-+ retValue = PCI_VENDOR_ID_BROADCOM | 0x63000000;
-+ break;
-+ case PCI_COMMAND:
-+ case PCI_STATUS:
-+ retValue = (0x0006 << 16) | usb_cfg_space_cmd_reg;
-+ break;
-+ case PCI_CLASS_REVISION:
-+ case PCI_CLASS_DEVICE:
-+ retValue = (PCI_CLASS_SERIAL_USB << 16) | (0x10 << 8) | 0x01;
-+ break;
-+ case PCI_BASE_ADDRESS_0:
-+ if (usb_mem_size_rd) {
-+ retValue = USB_BAR0_MEM_SIZE;
-+ } else {
-+ if (usb_mem_base != 0)
-+ retValue = usb_mem_base;
-+ else
-+ retValue = USB_HOST_BASE;
-+ }
-+ usb_mem_size_rd = FALSE;
-+ break;
-+ case PCI_CACHE_LINE_SIZE:
-+ case PCI_LATENCY_TIMER:
-+ retValue = 0;
-+ break;
-+ case PCI_HEADER_TYPE:
-+ retValue = PCI_HEADER_TYPE_NORMAL;
-+ break;
-+ case PCI_SUBSYSTEM_VENDOR_ID:
-+ retValue = PCI_VENDOR_ID_BROADCOM;
-+ break;
-+ case PCI_SUBSYSTEM_ID:
-+ retValue = 0x6300;
-+ break;
-+ case PCI_INTERRUPT_LINE:
-+ retValue = INTERRUPT_ID_USBH;
-+ break;
-+ default:
-+ break;
-+ }
-+
-+ switch (size) {
-+ case 1:
-+ *value = (retValue >> ((where & 3) << 3)) & 0xff;
-+ DPRINT("R <= Slot: %d Where: %2X Len: %d Data: %02X\n",
-+ PCI_SLOT(devfn), where, size, *value);
-+ break;
-+ case 2:
-+ *value = (retValue >> ((where & 3) << 3)) & 0xffff;
-+ DPRINT("R <= Slot: %d Where: %2X Len: %d Data: %04X\n",
-+ PCI_SLOT(devfn), where, size, *value);
-+ break;
-+ case 4:
-+ *value = retValue;
-+ DPRINT("R <= Slot: %d Where: %2X Len: %d Data: %08lX\n",
-+ PCI_SLOT(devfn), where, size, *value);
-+ break;
-+ default:
-+ break;
-+ }
-+
-+ return PCIBIOS_SUCCESSFUL;
-+}
-+#endif
-+
-+static int bcm96348_pcibios_read(struct pci_bus *bus, unsigned int devfn,
-+ int where, int size, u32 * val)
-+{
-+ volatile unsigned char *ioBase = (unsigned char *)(mpi->l2piobase | KSEG1);
-+ uint32 data;
-+
-+#if defined(CONFIG_USB)
-+ if (PCI_SLOT(devfn) == USB_HOST_SLOT)
-+ return pci63xx_int_read(devfn, where, val, size);
-+#endif
-+
-+ mpi_SetupPciConfigAccess(BCM_PCI_CFG(PCI_SLOT(devfn), PCI_FUNC(devfn), where));
-+ data = *(uint32 *)ioBase;
-+ switch(size) {
-+ case 1:
-+ *val = (data >> ((where & 3) << 3)) & 0xff;
-+ break;
-+ case 2:
-+ *val = (data >> ((where & 3) << 3)) & 0xffff;
-+ break;
-+ case 4:
-+ *val = data;
-+ /* Special case for reading PCI device range */
-+ if ((where >= PCI_BASE_ADDRESS_0) && (where <= PCI_BASE_ADDRESS_5)) {
-+ if (pci_mem_size_rd) {
-+ /* bcm6348 PCI memory window minimum size is 64K */
-+ *val &= PCI_SIZE_64K;
-+ }
-+ }
-+ break;
-+ default:
-+ break;
-+ }
-+ pci_mem_size_rd = FALSE;
-+ mpi_ClearPciConfigAccess();
-+
-+ return PCIBIOS_SUCCESSFUL;
-+}
-+
-+static int bcm96348_pcibios_write(struct pci_bus *bus, unsigned int devfn,
-+ int where, int size, u32 val)
-+{
-+ volatile unsigned char *ioBase = (unsigned char *)(mpi->l2piobase | KSEG1);
-+ uint32 data;
-+
-+#if defined(CONFIG_USB)
-+ if (PCI_SLOT(devfn) == USB_HOST_SLOT)
-+ return pci63xx_int_write(devfn, where, &val, size);
-+#endif
-+ mpi_SetupPciConfigAccess(BCM_PCI_CFG(PCI_SLOT(devfn), PCI_FUNC(devfn), where));
-+ data = *(uint32 *)ioBase;
-+ switch(size) {
-+ case 1:
-+ data = (data & ~(0xff << ((where & 3) << 3))) |
-+ (val << ((where & 3) << 3));
-+ break;
-+ case 2:
-+ data = (data & ~(0xffff << ((where & 3) << 3))) |
-+ (val << ((where & 3) << 3));
-+ break;
-+ case 4:
-+ data = val;
-+ /* Special case for reading PCI device range */
-+ if ((where >= PCI_BASE_ADDRESS_0) && (where <= PCI_BASE_ADDRESS_5)) {
-+ if (val == 0xffffffff)
-+ pci_mem_size_rd = TRUE;
-+ }
-+ break;
-+ default:
-+ break;
-+ }
-+ *(uint32 *)ioBase = data;
-+ udelay(500);
-+ mpi_ClearPciConfigAccess();
-+
-+ return PCIBIOS_SUCCESSFUL;
-+}
-+
-+struct pci_ops bcm96348_pci_ops = {
-+ .read = bcm96348_pcibios_read,
-+ .write = bcm96348_pcibios_write
-+};
-diff -urN linux-2.6.19/arch/mips/pci/pci-bcm96348.c linux-2.6.19.new/arch/mips/pci/pci-bcm96348.c
---- linux-2.6.19/arch/mips/pci/pci-bcm96348.c 1970-01-01 01:00:00.000000000 +0100
-+++ linux-2.6.19.new/arch/mips/pci/pci-bcm96348.c 2006-12-16 18:46:31.000000000 +0100
-@@ -0,0 +1,54 @@
-+/*
-+<:copyright-gpl
-+ Copyright 2002 Broadcom Corp. All Rights Reserved.
-+
-+ This program is free software; you can distribute it and/or modify it
-+ under the terms of the GNU General Public License (Version 2) as
-+ published by the Free Software Foundation.
-+
-+ This program is distributed in the hope it will be useful, but WITHOUT
-+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-+ for more details.
-+
-+ You should have received a copy of the GNU General Public License along
-+ with this program; if not, write to the Free Software Foundation, Inc.,
-+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-+:>
-+*/
-+#include <linux/types.h>
-+#include <linux/pci.h>
-+#include <linux/kernel.h>
-+#include <linux/init.h>
-+
-+//#include <asm/pci_channel.h>
-+#include <bcmpci.h>
-+
-+static struct resource bcm_pci_io_resource = {
-+ .name = "bcm96348 pci IO space",
-+ .start = BCM_PCI_IO_BASE,
-+ .end = BCM_PCI_IO_BASE + BCM_PCI_IO_SIZE_64KB - 1,
-+ .flags = IORESOURCE_IO
-+};
-+
-+static struct resource bcm_pci_mem_resource = {
-+ .name = "bcm96348 pci memory space",
-+ .start = BCM_PCI_MEM_BASE,
-+ .end = BCM_PCI_MEM_BASE + BCM_PCI_MEM_SIZE_16MB - 1,
-+ .flags = IORESOURCE_MEM
-+};
-+
-+extern struct pci_ops bcm96348_pci_ops;
-+
-+struct pci_controller bcm96348_controller = {
-+ .pci_ops = &bcm96348_pci_ops,
-+ .io_resource = &bcm_pci_io_resource,
-+ .mem_resource = &bcm_pci_mem_resource,
-+};
-+
-+static void bcm96348_pci_init(void)
-+{
-+ register_pci_controller(&bcm96348_controller);
-+}
-+
-+arch_initcall(bcm96348_pci_init);
-diff -urN linux-2.6.19/drivers/serial/Makefile linux-2.6.19.new/drivers/serial/Makefile
---- linux-2.6.19/drivers/serial/Makefile 2006-11-29 22:57:37.000000000 +0100
-+++ linux-2.6.19.new/drivers/serial/Makefile 2006-12-16 18:49:17.000000000 +0100
-@@ -56,3 +56,4 @@
- obj-$(CONFIG_SERIAL_SGI_IOC3) += ioc3_serial.o
- obj-$(CONFIG_SERIAL_ATMEL) += atmel_serial.o
- obj-$(CONFIG_SERIAL_NETX) += netx-serial.o
-+obj-$(CONFIG_BCM_SERIAL) += bcm63xx_cons.o
-diff -urN linux-2.6.19/drivers/serial/bcm63xx_cons.c linux-2.6.19.new/drivers/serial/bcm63xx_cons.c
---- linux-2.6.19/drivers/serial/bcm63xx_cons.c 1970-01-01 01:00:00.000000000 +0100
-+++ linux-2.6.19.new/drivers/serial/bcm63xx_cons.c 2006-12-16 18:46:31.000000000 +0100
-@@ -0,0 +1,1049 @@
-+/*
-+<:copyright-gpl
-+ Copyright 2002 Broadcom Corp. All Rights Reserved.
-+
-+ This program is free software; you can distribute it and/or modify it
-+ under the terms of the GNU General Public License (Version 2) as
-+ published by the Free Software Foundation.
-+
-+ This program is distributed in the hope it will be useful, but WITHOUT
-+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-+ for more details.
-+
-+ You should have received a copy of the GNU General Public License along
-+ with this program; if not, write to the Free Software Foundation, Inc.,
-+ 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-+:>
-+*/
-+
-+/* Description: Serial port driver for the BCM963XX. */
-+
-+#define CARDNAME "bcm963xx_serial driver"
-+#define VERSION "2.0"
-+#define VER_STR CARDNAME " v" VERSION "\n"
-+
-+
-+#include <linux/kernel.h>
-+#include <linux/module.h>
-+#include <linux/version.h>
-+#include <linux/init.h>
-+#include <linux/slab.h>
-+#include <linux/interrupt.h>
-+#include <linux/spinlock.h>
-+
-+/* for definition of struct console */
-+#include <linux/console.h>
-+#include <linux/tty.h>
-+#include <linux/tty_flip.h>
-+#include <linux/serial.h>
-+#include <linux/serialP.h>
-+#include <asm/uaccess.h>
-+
-+#include <bcmtypes.h>
-+#include <board.h>
-+#include <bcm_map_part.h>
-+#include <bcm_intr.h>
-+
-+static DEFINE_SPINLOCK(bcm963xx_serial_lock);
-+
-+extern void _putc(char);
-+extern void _puts(const char *);
-+
-+typedef struct bcm_serial {
-+ volatile Uart * port;
-+ int type;
-+ int flags;
-+ int irq;
-+ int baud_base;
-+ int blocked_open;
-+ unsigned short close_delay;
-+ unsigned short closing_wait;
-+ unsigned short line; /* port/line number */
-+ unsigned short cflags; /* line configuration flag */
-+ unsigned short x_char; /* xon/xoff character */
-+ unsigned short read_status_mask; /* mask for read condition */
-+ unsigned short ignore_status_mask; /* mask for ignore condition */
-+ unsigned long event; /* mask used in BH */
-+ int xmit_head; /* Position of the head */
-+ int xmit_tail; /* Position of the tail */
-+ int xmit_cnt; /* Count of the chars in the buffer */
-+ int count; /* indicates how many times it has been opened */
-+ int magic;
-+
-+ struct async_icount icount; /* keep track of things ... */
-+ struct tty_struct *tty; /* tty associated */
-+ struct termios normal_termios;
-+
-+ wait_queue_head_t open_wait;
-+ wait_queue_head_t close_wait;
-+
-+ long session; /* Session of opening process */
-+ long pgrp; /* pgrp of opening process */
-+
-+ unsigned char is_initialized;
-+} Context;
-+
-+
-+/*---------------------------------------------------------------------*/
-+/* Define bits in the Interrupt Enable register */
-+/*---------------------------------------------------------------------*/
-+/* Enable receive interrupt */
-+#define RXINT (RXFIFONE|RXOVFERR)
-+
-+/* Enable transmit interrupt */
-+#define TXINT (TXFIFOEMT|TXUNDERR|TXOVFERR)
-+
-+/* Enable receiver line status interrupt */
-+#define LSINT (RXBRK|RXPARERR|RXFRAMERR)
-+
-+#define BCM_NUM_UARTS 1
-+
-+#define BD_BCM63XX_TIMER_CLOCK_INPUT (FPERIPH)
-+
-+
-+static struct bcm_serial multi[BCM_NUM_UARTS];
-+static struct bcm_serial *lines[BCM_NUM_UARTS];
-+static struct tty_driver *serial_driver;
-+static struct termios *serial_termios[BCM_NUM_UARTS];
-+static struct termios *serial_termios_locked[BCM_NUM_UARTS];
-+
-+
-+static void bcm_stop (struct tty_struct *tty);
-+static void bcm_start (struct tty_struct *tty);
-+static inline void receive_chars (struct bcm_serial * info);
-+static int startup (struct bcm_serial *info);
-+static void shutdown (struct bcm_serial * info);
-+static void change_speed( volatile Uart *pUart, tcflag_t cFlag );
-+static void bcm63xx_cons_flush_chars (struct tty_struct *tty);
-+static int bcm63xx_cons_write (struct tty_struct *tty,
-+ const unsigned char *buf, int count);
-+static int bcm63xx_cons_write_room (struct tty_struct *tty);
-+static int bcm_chars_in_buffer (struct tty_struct *tty);
-+static void bcm_flush_buffer (struct tty_struct *tty);
-+static void bcm_throttle (struct tty_struct *tty);
-+static void bcm_unthrottle (struct tty_struct *tty);
-+static void bcm_send_xchar (struct tty_struct *tty, char ch);
-+static int get_serial_info(struct bcm_serial *info, struct serial_struct *retinfo);
-+static int set_serial_info (struct bcm_serial *info, struct serial_struct *new_info);
-+static int get_lsr_info (struct bcm_serial *info, unsigned int *value);
-+static void send_break (struct bcm_serial *info, int duration);
-+static int bcm_ioctl (struct tty_struct * tty, struct file * file,
-+ unsigned int cmd, unsigned long arg);
-+static void bcm_set_termios (struct tty_struct *tty, struct termios *old_termios);
-+static void bcm63xx_cons_close (struct tty_struct *tty, struct file *filp);
-+static void bcm_hangup (struct tty_struct *tty);
-+static int block_til_ready (struct tty_struct *tty, struct file *filp, struct bcm_serial *info);
-+static int bcm63xx_cons_open (struct tty_struct * tty, struct file * filp);
-+static int __init bcm63xx_serialinit(void);
-+
-+
-+/*
-+ * ------------------------------------------------------------
-+ * rs_stop () and rs_start ()
-+ *
-+ * These routines are called before setting or resetting
-+ * tty->stopped. They enable or disable transmitter interrupts,
-+ * as necessary.
-+ * ------------------------------------------------------------
-+ */
-+static void bcm_stop (struct tty_struct *tty)
-+{
-+}
-+
-+static void bcm_start (struct tty_struct *tty)
-+{
-+ _puts(CARDNAME " Start\n");
-+}
-+
-+/*
-+ * ------------------------------------------------------------
-+ * receive_char ()
-+ *
-+ * This routine deals with inputs from any lines.
-+ * ------------------------------------------------------------
-+ */
-+static inline void receive_chars (struct bcm_serial * info)
-+{
-+ struct tty_struct *tty = 0;
-+ struct async_icount * icount;
-+ int ignore = 0;
-+ unsigned short status, tmp;
-+ UCHAR ch = 0;
-+ while ((status = info->port->intStatus) & RXINT)
-+ {
-+ char flag_char = TTY_NORMAL;
-+
-+ if (status & RXFIFONE)
-+ ch = info->port->Data; // Read the character
-+ tty = info->tty; /* now tty points to the proper dev */
-+ icount = &info->icount;
-+ if (! tty)
-+ break;
-+ if (!tty_buffer_request_room(tty, 1))
-+ break;
-+ icount->rx++;
-+ if (status & RXBRK)
-+ {
-+ flag_char = TTY_BREAK;
-+ icount->brk++;
-+ }
-+ // keep track of the statistics
-+ if (status & (RXFRAMERR | RXPARERR | RXOVFERR))
-+ {
-+ if (status & RXPARERR) /* parity error */
-+ icount->parity++;
-+ else
-+ if (status & RXFRAMERR) /* frame error */
-+ icount->frame++;
-+ if (status & RXOVFERR)
-+ {
-+ // Overflow. Reset the RX FIFO
-+ info->port->fifoctl |= RSTRXFIFOS;
-+ icount->overrun++;
-+ }
-+ // check to see if we should ignore the character
-+ // and mask off conditions that should be ignored
-+ if (status & info->ignore_status_mask)
-+ {
-+ if (++ignore > 100 )
-+ break;
-+ goto ignore_char;
-+ }
-+ // Mask off the error conditions we want to ignore
-+ tmp = status & info->read_status_mask;
-+ if (tmp & RXPARERR)
-+ {
-+ flag_char = TTY_PARITY;
-+ }
-+ else
-+ if (tmp & RXFRAMERR)
-+ {
-+ flag_char = TTY_FRAME;
-+ }
-+ if (tmp & RXOVFERR)
-+ {
-+ tty_insert_flip_char(tty, ch, flag_char);
-+ ch = 0;
-+ flag_char = TTY_OVERRUN;
-+ if (!tty_buffer_request_room(tty, 1))
-+ break;
-+ }
-+ }
-+ tty_insert_flip_char(tty, ch, flag_char);
-+ }
-+ignore_char:;
-+ tty_flip_buffer_push(tty);
-+ tty_schedule_flip(tty);
-+
-+}
-+
-+
-+/*
-+ * ------------------------------------------------------------
-+ * bcm_interrupt ()
-+ *
-+ * this is the main interrupt routine for the chip.
-+ * It deals with the multiple ports.
-+ * ------------------------------------------------------------
-+ */
-+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,0)
-+static irqreturn_t bcm_interrupt (int irq, void * dev)
-+#else
-+static void bcm_interrupt (int irq, void * dev, struct pt_regs * regs)
-+#endif
-+{
-+ struct bcm_serial * info = lines[0];
-+ UINT16 intStat;
-+
-+ /* get pending interrupt flags from UART */
-+
-+ /* Mask with only the serial interrupts that are enabled */
-+ intStat = info->port->intStatus & info->port->intMask;
-+ while (intStat)
-+ {
-+ if (intStat & RXINT)
-+ receive_chars (info);
-+ else
-+ if (intStat & TXINT)
-+ info->port->intStatus = TXINT;
-+ else /* don't know what it was, so let's mask it */
-+ info->port->intMask &= ~intStat;
-+
-+ intStat = info->port->intStatus & info->port->intMask;
-+ }
-+
-+ // Clear the interrupt
-+ BcmHalInterruptEnable (INTERRUPT_ID_UART);
-+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,0)
-+ return IRQ_HANDLED;
-+#endif
-+}
-+
-+/*
-+ * -------------------------------------------------------------------
-+ * startup ()
-+ *
-+ * various initialization tasks
-+ * -------------------------------------------------------------------
-+ */
-+static int startup (struct bcm_serial *info)
-+{
-+ // Port is already started...
-+ return 0;
-+}
-+
-+/*
-+ * -------------------------------------------------------------------
-+ * shutdown ()
-+ *
-+ * This routine will shutdown a serial port; interrupts are disabled, and
-+ * DTR is dropped if the hangup on close termio flag is on.
-+ * -------------------------------------------------------------------
-+ */
-+static void shutdown (struct bcm_serial * info)
-+{
-+ unsigned long flags;
-+ if (!info->is_initialized)
-+ return;
-+
-+ spin_lock_irqsave(&bcm963xx_serial_lock, flags);
-+
-+ info->port->control &= ~(BRGEN|TXEN|RXEN);
-+ if (info->tty)
-+ set_bit (TTY_IO_ERROR, &info->tty->flags);
-+ info->is_initialized = 0;
-+
-+ spin_unlock_irqrestore(&bcm963xx_serial_lock, flags);
-+}
-+/*
-+ * -------------------------------------------------------------------
-+ * change_speed ()
-+ *
-+ * Set the baud rate, character size, parity and stop bits.
-+ * -------------------------------------------------------------------
-+ */
-+static void change_speed( volatile Uart *pUart, tcflag_t cFlag )
-+{
-+ unsigned long ulFlags, ulBaud, ulClockFreqHz, ulTmp;
-+
-+ spin_lock_irqsave(&bcm963xx_serial_lock, ulFlags);
-+ switch( cFlag & (CBAUD | CBAUDEX) )
-+ {
-+ case B115200:
-+ ulBaud = 115200;
-+ break;
-+ case B57600:
-+ ulBaud = 57600;
-+ break;
-+ case B38400:
-+ ulBaud = 38400;
-+ break;
-+ case B19200:
-+ ulBaud = 19200;
-+ break;
-+ case B9600:
-+ ulBaud = 9600;
-+ break;
-+ case B4800:
-+ ulBaud = 4800;
-+ break;
-+ case B2400:
-+ ulBaud = 2400;
-+ break;
-+ case B1800:
-+ ulBaud = 1800;
-+ break;
-+ case B1200:
-+ ulBaud = 1200;
-+ break;
-+ case B600:
-+ ulBaud = 600;
-+ break;
-+ case B300:
-+ ulBaud = 300;
-+ break;
-+ case B200:
-+ ulBaud = 200;
-+ break;
-+ case B150:
-+ ulBaud = 150;
-+ break;
-+ case B134:
-+ ulBaud = 134;
-+ break;
-+ case B110:
-+ ulBaud = 110;
-+ break;
-+ case B75:
-+ ulBaud = 75;
-+ break;
-+ case B50:
-+ ulBaud = 50;
-+ break;
-+ default:
-+ ulBaud = 115200;
-+ break;
-+ }
-+
-+ /* Calculate buad rate. */
-+ ulClockFreqHz = BD_BCM63XX_TIMER_CLOCK_INPUT;
-+ ulTmp = (ulClockFreqHz / ulBaud) / 16;
-+ if( ulTmp & 0x01 )
-+ ulTmp /= 2; /* Rounding up, so sub is already accounted for */
-+ else
-+ ulTmp = (ulTmp / 2) - 1; /* Rounding down so we must sub 1 */
-+ pUart->baudword = ulTmp;
-+
-+ /* Set character size, stop bits and parity. */
-+ switch( cFlag & CSIZE )
-+ {
-+ case CS5:
-+ ulTmp = BITS5SYM; /* select transmit 5 bit data size */
-+ break;
-+ case CS6:
-+ ulTmp = BITS6SYM; /* select transmit 6 bit data size */
-+ break;
-+ case CS7:
-+ ulTmp = BITS7SYM; /* select transmit 7 bit data size */
-+ break;
-+ default:
-+ ulTmp = BITS8SYM; /* select transmit 8 bit data size */
-+ break;
-+ }
-+ if( cFlag & CSTOPB )
-+ ulTmp |= TWOSTOP; /* select 2 stop bits */
-+ else
-+ ulTmp |= ONESTOP; /* select one stop bit */
-+
-+ /* Write these values into the config reg. */
-+ pUart->config = ulTmp;
-+ pUart->control &= ~(RXPARITYEN | TXPARITYEN | RXPARITYEVEN | TXPARITYEVEN);
-+ switch( cFlag & (PARENB | PARODD) )
-+ {
-+ case PARENB|PARODD:
-+ pUart->control |= RXPARITYEN | TXPARITYEN;
-+ break;
-+ case PARENB:
-+ pUart->control |= RXPARITYEN | TXPARITYEN | RXPARITYEVEN | TXPARITYEVEN;
-+ break;
-+ default:
-+ pUart->control |= 0;
-+ break;
-+ }
-+
-+ /* Reset and flush uart */
-+ pUart->fifoctl = RSTTXFIFOS | RSTRXFIFOS;
-+ spin_unlock_irqrestore(&bcm963xx_serial_lock, ulFlags);
-+}
-+
-+
-+/*
-+ * -------------------------------------------------------------------
-+ * bcm_flush_char ()
-+ *
-+ * Nothing to flush. Polled I/O is used.
-+ * -------------------------------------------------------------------
-+ */
-+static void bcm63xx_cons_flush_chars (struct tty_struct *tty)
-+{
-+}
-+
-+
-+/*
-+ * -------------------------------------------------------------------
-+ * bcm63xx_cons_write ()
-+ *
-+ * Main output routine using polled I/O.
-+ * -------------------------------------------------------------------
-+ */
-+static int bcm63xx_cons_write (struct tty_struct *tty,
-+ const unsigned char *buf, int count)
-+{
-+ int c;
-+
-+ for (c = 0; c < count; c++)
-+ _putc(buf[c]);
-+ return count;
-+}
-+
-+/*
-+ * -------------------------------------------------------------------
-+ * bcm63xx_cons_write_room ()
-+ *
-+ * Compute the amount of space available for writing.
-+ * -------------------------------------------------------------------
-+ */
-+static int bcm63xx_cons_write_room (struct tty_struct *tty)
-+{
-+ /* Pick a number. Any number. Polled I/O is used. */
-+ return 1024;
-+}
-+
-+/*
-+ * -------------------------------------------------------------------
-+ * bcm_chars_in_buffer ()
-+ *
-+ * compute the amount of char left to be transmitted
-+ * -------------------------------------------------------------------
-+ */
-+static int bcm_chars_in_buffer (struct tty_struct *tty)
-+{
-+ return 0;
-+}
-+
-+/*
-+ * -------------------------------------------------------------------
-+ * bcm_flush_buffer ()
-+ *
-+ * Empty the output buffer
-+ * -------------------------------------------------------------------
-+ */
-+static void bcm_flush_buffer (struct tty_struct *tty)
-+{
-+ tty_wakeup(tty);
-+}
-+
-+/*
-+ * ------------------------------------------------------------
-+ * bcm_throttle () and bcm_unthrottle ()
-+ *
-+ * This routine is called by the upper-layer tty layer to signal that
-+ * incoming characters should be throttled (or not).
-+ * ------------------------------------------------------------
-+ */
-+static void bcm_throttle (struct tty_struct *tty)
-+{
-+ struct bcm_serial *info = (struct bcm_serial *)tty->driver_data;
-+ if (I_IXOFF(tty))
-+ info->x_char = STOP_CHAR(tty);
-+}
-+
-+static void bcm_unthrottle (struct tty_struct *tty)
-+{
-+ struct bcm_serial *info = (struct bcm_serial *)tty->driver_data;
-+ if (I_IXOFF(tty))
-+ {
-+ if (info->x_char)
-+ info->x_char = 0;
-+ else
-+ info->x_char = START_CHAR(tty);
-+ }
-+}
-+
-+static void bcm_send_xchar (struct tty_struct *tty, char ch)
-+{
-+ struct bcm_serial *info = (struct bcm_serial *)tty->driver_data;
-+ info->x_char = ch;
-+ if (ch)
-+ bcm_start (info->tty);
-+}
-+
-+/*
-+ * ------------------------------------------------------------
-+ * rs_ioctl () and friends
-+ * ------------------------------------------------------------
-+ */
-+static int get_serial_info(struct bcm_serial *info, struct serial_struct *retinfo)
-+{
-+ struct serial_struct tmp;
-+
-+ if (!retinfo)
-+ return -EFAULT;
-+
-+ memset (&tmp, 0, sizeof(tmp));
-+ tmp.type = info->type;
-+ tmp.line = info->line;
-+ tmp.port = (int) info->port;
-+ tmp.irq = info->irq;
-+ tmp.flags = 0;
-+ tmp.baud_base = info->baud_base;
-+ tmp.close_delay = info->close_delay;
-+ tmp.closing_wait = info->closing_wait;
-+
-+ return copy_to_user (retinfo, &tmp, sizeof(*retinfo));
-+}
-+
-+static int set_serial_info (struct bcm_serial *info, struct serial_struct *new_info)
-+{
-+ struct serial_struct new_serial;
-+ struct bcm_serial old_info;
-+ int retval = 0;
-+
-+ if (!new_info)
-+ return -EFAULT;
-+
-+ copy_from_user (&new_serial, new_info, sizeof(new_serial));
-+ old_info = *info;
-+
-+ if (!capable(CAP_SYS_ADMIN))
-+ return -EPERM;
-+
-+
-+ if (info->count > 1)
-+ return -EBUSY;
-+
-+ /* OK, past this point, all the error checking has been done.
-+ * At this point, we start making changes.....
-+ */
-+ info->baud_base = new_serial.baud_base;
-+ info->type = new_serial.type;
-+ info->close_delay = new_serial.close_delay;
-+ info->closing_wait = new_serial.closing_wait;
-+ retval = startup (info);
-+ return retval;
-+}
-+
-+/*
-+ * get_lsr_info - get line status register info
-+ *
-+ * Purpose: Let user call ioctl() to get info when the UART physically
-+ * is emptied. On bus types like RS485, the transmitter must
-+ * release the bus after transmitting. This must be done when
-+ * the transmit shift register is empty, not be done when the
-+ * transmit holding register is empty. This functionality
-+ * allows an RS485 driver to be written in user space.
-+ */
-+static int get_lsr_info (struct bcm_serial *info, unsigned int *value)
-+{
-+ return( 0 );
-+}
-+
-+/*
-+ * This routine sends a break character out the serial port.
-+ */
-+static void send_break (struct bcm_serial *info, int duration)
-+{
-+ unsigned long flags;
-+
-+ if (!info->port)
-+ return;
-+
-+ current->state = TASK_INTERRUPTIBLE;
-+
-+ /*save_flags (flags);
-+ cli();*/
-+ spin_lock_irqsave(&bcm963xx_serial_lock, flags);
-+
-+ info->port->control |= XMITBREAK;
-+ schedule_timeout(duration);
-+ info->port->control &= ~XMITBREAK;
-+
-+ spin_unlock_irqrestore(&bcm963xx_serial_lock, flags);
-+ //restore_flags (flags);
-+}
-+
-+static int bcm_ioctl (struct tty_struct * tty, struct file * file,
-+ unsigned int cmd, unsigned long arg)
-+{
-+ int error;
-+ struct bcm_serial * info = (struct bcm_serial *)tty->driver_data;
-+ int retval;
-+
-+ if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
-+ (cmd != TIOCSERCONFIG) && (cmd != TIOCSERGWILD) &&
-+ (cmd != TIOCSERSWILD) && (cmd != TIOCSERGSTRUCT))
-+ {
-+ if (tty->flags & (1 << TTY_IO_ERROR))
-+ return -EIO;
-+ }
-+ switch (cmd)
-+ {
-+
-+ case TCSBRK: /* SVID version: non-zero arg --> no break */
-+ retval = tty_check_change (tty);
-+ if (retval)
-+ return retval;
-+ tty_wait_until_sent (tty, 0);
-+ if (!arg)
-+ send_break (info, HZ/4); /* 1/4 second */
-+ return 0;
-+
-+ case TCSBRKP: /* support for POSIX tcsendbreak() */
-+ retval = tty_check_change (tty);
-+ if (retval)
-+ return retval;
-+ tty_wait_until_sent (tty, 0);
-+ send_break (info, arg ? arg*(HZ/10) : HZ/4);
-+ return 0;
-+
-+ case TIOCGSOFTCAR:
-+ error = access_ok (VERIFY_WRITE, (void *)arg, sizeof(long));
-+ if (!error)
-+ return -EFAULT;
-+ else
-+ {
-+ put_user (C_CLOCAL(tty) ? 1 : 0, (unsigned long *)arg);
-+ return 0;
-+ }
-+
-+ case TIOCSSOFTCAR:
-+ error = get_user (arg, (unsigned long *)arg);
-+ if (error)
-+ return error;
-+ tty->termios->c_cflag = ((tty->termios->c_cflag & ~CLOCAL) | (arg ? CLOCAL : 0));
-+ return 0;
-+
-+ case TIOCGSERIAL:
-+ error = access_ok (VERIFY_WRITE, (void *)arg, sizeof(struct serial_struct));
-+ if (!error)
-+ return -EFAULT;
-+ else
-+ return get_serial_info (info, (struct serial_struct *)arg);
-+
-+ case TIOCSSERIAL:
-+ return set_serial_info (info, (struct serial_struct *) arg);
-+
-+ case TIOCSERGETLSR: /* Get line status register */
-+ error = access_ok (VERIFY_WRITE, (void *)arg, sizeof(unsigned int));
-+ if (!error)
-+ return -EFAULT;
-+ else
-+ return get_lsr_info (info, (unsigned int *)arg);
-+
-+ case TIOCSERGSTRUCT:
-+ error = access_ok (VERIFY_WRITE, (void *)arg, sizeof(struct bcm_serial));
-+ if (!error)
-+ return -EFAULT;
-+ else
-+ {
-+ copy_to_user((struct bcm_serial *)arg, info, sizeof(struct bcm_serial));
-+ return 0;
-+ }
-+
-+ default:
-+ return -ENOIOCTLCMD;
-+ }
-+ return 0;
-+}
-+
-+static void bcm_set_termios (struct tty_struct *tty, struct termios *old_termios)
-+{
-+ struct bcm_serial *info = (struct bcm_serial *)tty->driver_data;
-+
-+ if( tty->termios->c_cflag != old_termios->c_cflag )
-+ change_speed (info->port, tty->termios->c_cflag);
-+}
-+
-+/*
-+ * ------------------------------------------------------------
-+ * bcm63xx_cons_close()
-+ *
-+ * This routine is called when the serial port gets closed. First, we
-+ * wait for the last remaining data to be sent. Then, we turn off
-+ * the transmit enable and receive enable flags.
-+ * ------------------------------------------------------------
-+ */
-+static void bcm63xx_cons_close (struct tty_struct *tty, struct file *filp)
-+{
-+ struct bcm_serial * info = (struct bcm_serial *)tty->driver_data;
-+ unsigned long flags;
-+
-+ if (!info)
-+ return;
-+
-+ /*save_flags (flags);
-+ cli();*/
-+ spin_lock_irqsave(&bcm963xx_serial_lock, flags);
-+
-+ if (tty_hung_up_p (filp))
-+ {
-+ spin_unlock_irqrestore(&bcm963xx_serial_lock, flags);
-+ //restore_flags (flags);
-+ return;
-+ }
-+
-+ if ((tty->count == 1) && (info->count != 1))
-+ {
-+
-+ /* Uh, oh. tty->count is 1, which means that the tty
-+ * structure will be freed. Info->count should always
-+ * be one in these conditions. If it's greater than
-+ * one, we've got real problems, since it means the
-+ * serial port won't be shutdown.
-+ */
-+ printk("bcm63xx_cons_close: bad serial port count; tty->count is 1, "
-+ "info->count is %d\n", info->count);
-+ info->count = 1;
-+ }
-+
-+ if (--info->count < 0)
-+ {
-+ printk("ds_close: bad serial port count for ttys%d: %d\n",
-+ info->line, info->count);
-+ info->count = 0;
-+ }
-+
-+ if (info->count)
-+ {
-+ //restore_flags (flags);
-+ spin_unlock_irqrestore(&bcm963xx_serial_lock, flags);
-+ return;
-+ }
-+
-+ /* Now we wait for the transmit buffer to clear; and we notify
-+ * the line discipline to only process XON/XOFF characters.
-+ */
-+ tty->closing = 1;
-+
-+ /* At this point we stop accepting input. To do this, we
-+ * disable the receive line status interrupts.
-+ */
-+ shutdown (info);
-+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,0)
-+ if (tty->driver->flush_buffer)
-+ tty->driver->flush_buffer (tty);
-+#else
-+ if (tty->driver.flush_buffer)
-+ tty->driver.flush_buffer (tty);
-+#endif
-+ if (tty->ldisc.flush_buffer)
-+ tty->ldisc.flush_buffer (tty);
-+
-+ tty->closing = 0;
-+ info->event = 0;
-+ info->tty = 0;
-+ if (tty->ldisc.num != tty_ldisc_get(N_TTY)->num)
-+ {
-+ if (tty->ldisc.close)
-+ (tty->ldisc.close)(tty);
-+ tty->ldisc = *tty_ldisc_get(N_TTY);
-+ tty->termios->c_line = N_TTY;
-+ if (tty->ldisc.open)
-+ (tty->ldisc.open)(tty);
-+ }
-+ if (info->blocked_open)
-+ {
-+ if (info->close_delay)
-+ {
-+ current->state = TASK_INTERRUPTIBLE;
-+ schedule_timeout(info->close_delay);
-+ }
-+ wake_up_interruptible (&info->open_wait);
-+ }
-+ wake_up_interruptible (&info->close_wait);
-+
-+ //restore_flags (flags);
-+ spin_unlock_irqrestore(&bcm963xx_serial_lock, flags);
-+}
-+
-+/*
-+ * bcm_hangup () --- called by tty_hangup() when a hangup is signaled.
-+ */
-+static void bcm_hangup (struct tty_struct *tty)
-+{
-+
-+ struct bcm_serial *info = (struct bcm_serial *)tty->driver_data;
-+
-+ shutdown (info);
-+ info->event = 0;
-+ info->count = 0;
-+ info->tty = 0;
-+ wake_up_interruptible (&info->open_wait);
-+}
-+
-+/*
-+ * ------------------------------------------------------------
-+ * rs_open() and friends
-+ * ------------------------------------------------------------
-+ */
-+static int block_til_ready (struct tty_struct *tty, struct file *filp,
-+ struct bcm_serial *info)
-+{
-+ return 0;
-+}
-+
-+/*
-+ * This routine is called whenever a serial port is opened. It
-+ * enables interrupts for a serial port. It also performs the
-+ * serial-specific initialization for the tty structure.
-+ */
-+static int bcm63xx_cons_open (struct tty_struct * tty, struct file * filp)
-+{
-+ struct bcm_serial *info;
-+ int retval, line;
-+
-+ // Make sure we're only opening on of the ports we support
-+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,0)
-+ line = MINOR(tty->driver->cdev.dev) - tty->driver->minor_start;
-+#else
-+ line = MINOR(tty->device) - tty->driver.minor_start;
-+#endif
-+
-+ if ((line < 0) || (line >= BCM_NUM_UARTS))
-+ return -ENODEV;
-+
-+ info = lines[line];
-+
-+ tty->low_latency=1;
-+ info->port->intMask = 0; /* Clear any pending interrupts */
-+ info->port->intMask = RXINT; /* Enable RX */
-+
-+ info->count++;
-+ tty->driver_data = info;
-+ info->tty = tty;
-+ BcmHalInterruptEnable (INTERRUPT_ID_UART);
-+
-+ // Start up serial port
-+ retval = startup (info);
-+ if (retval)
-+ return retval;
-+
-+ retval = block_til_ready (tty, filp, info);
-+ if (retval)
-+ return retval;
-+
-+
-+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,0)
-+ info->pgrp = process_group(current);
-+ info->session = current->signal->session;
-+#else
-+ info->session = current->session;
-+ info->pgrp = current->pgrp;
-+#endif
-+
-+ return 0;
-+}
-+
-+
-+static struct tty_operations rs_ops = {
-+ .open = bcm63xx_cons_open,
-+ .close = bcm63xx_cons_close,
-+ .write = bcm63xx_cons_write,
-+ .flush_chars = bcm63xx_cons_flush_chars,
-+ .write_room = bcm63xx_cons_write_room,
-+ .chars_in_buffer = bcm_chars_in_buffer,
-+ .flush_buffer = bcm_flush_buffer,
-+ .ioctl = bcm_ioctl,
-+ .throttle = bcm_throttle,
-+ .unthrottle = bcm_unthrottle,
-+ .send_xchar = bcm_send_xchar,
-+ .set_termios = bcm_set_termios,
-+ .stop = bcm_stop,
-+ .start = bcm_start,
-+ .hangup = bcm_hangup,
-+};
-+
-+/* --------------------------------------------------------------------------
-+ Name: bcm63xx_serialinit
-+ Purpose: Initialize our BCM63xx serial driver
-+-------------------------------------------------------------------------- */
-+static int __init bcm63xx_serialinit(void)
-+{
-+ int i, flags;
-+ struct bcm_serial * info;
-+
-+ // Print the driver version information
-+ printk(VER_STR);
-+ serial_driver = alloc_tty_driver(BCM_NUM_UARTS);
-+ if (!serial_driver)
-+ return -ENOMEM;
-+
-+ serial_driver->owner = THIS_MODULE;
-+// serial_driver->devfs_name = "tts/";
-+// serial_driver.magic = TTY_DRIVER_MAGIC;
-+ serial_driver->name = "ttyS";
-+ serial_driver->major = TTY_MAJOR;
-+ serial_driver->minor_start = 64;
-+// serial_driver.num = BCM_NUM_UARTS;
-+ serial_driver->type = TTY_DRIVER_TYPE_SERIAL;
-+ serial_driver->subtype = SERIAL_TYPE_NORMAL;
-+ serial_driver->init_termios = tty_std_termios;
-+ serial_driver->init_termios.c_cflag = B115200 | CS8 | CREAD | HUPCL | CLOCAL;
-+ serial_driver->flags = TTY_DRIVER_REAL_RAW;
-+
-+ serial_driver->termios = serial_termios;
-+ serial_driver->termios_locked = serial_termios_locked;
-+
-+ tty_set_operations(serial_driver, &rs_ops);
-+
-+ if (tty_register_driver (serial_driver))
-+ panic("Couldn't register serial driver\n");
-+
-+ //save_flags(flags); cli();
-+ spin_lock_irqsave(&bcm963xx_serial_lock, flags);
-+
-+ for (i = 0; i < BCM_NUM_UARTS; i++)
-+ {
-+ info = &multi[i];
-+ lines[i] = info;
-+ info->magic = SERIAL_MAGIC;
-+ info->port = (Uart *) ((char *)UART_BASE + (i * 0x20));
-+ info->tty = 0;
-+ info->irq = (2 - i) + 8;
-+ info->line = i;
-+ info->close_delay = 50;
-+ info->closing_wait = 3000;
-+ info->x_char = 0;
-+ info->event = 0;
-+ info->count = 0;
-+ info->blocked_open = 0;
-+ info->normal_termios = serial_driver->init_termios;
-+ init_waitqueue_head(&info->open_wait);
-+ init_waitqueue_head(&info->close_wait);
-+
-+ /* If we are pointing to address zero then punt - not correctly
-+ * set up in setup.c to handle this.
-+ */
-+ if (! info->port)
-+ return 0;
-+ BcmHalMapInterrupt(bcm_interrupt, 0, INTERRUPT_ID_UART);
-+ }
-+
-+ /* order matters here... the trick is that flags
-+ * is updated... in request_irq - to immediatedly obliterate
-+ * it is unwise.
-+ */
-+ spin_unlock_irqrestore(&bcm963xx_serial_lock, flags);
-+ return 0;
-+}
++ select HW_HAS_PCI
++ select DMA_NONCOHERENT
++ select IRQ_CPU
++ select CFE
++ help
++ This is a fmaily of boards based on the Broadcom MIPS32
+
-+module_init(bcm63xx_serialinit);
+ config MIPS_MTX1
+ bool "4G Systems MTX-1 board"
+ select DMA_NONCOHERENT
+diff -urN linux-2.6.19/arch/mips/Makefile linux-2.6.19.new/arch/mips/Makefile
+--- linux-2.6.19/arch/mips/Makefile 2006-12-16 17:36:29.000000000 +0100
++++ linux-2.6.19.new/arch/mips/Makefile 2006-12-16 18:46:31.000000000 +0100
+@@ -158,6 +158,19 @@
+ #
+
+ #
++# Broadcom BCM963xx SoC
++#
++core-$(CONFIG_BCM963XX) += arch/mips/bcm963xx/
++cflags-$(CONFIG_BCM963XX) += -Iinclude/asm-mips/mach-bcm963xx
++load-$(CONFIG_BCM963XX) += 0xffffffff80010000
+
-+/* --------------------------------------------------------------------------
-+ Name: bcm_console_print
-+ Purpose: bcm_console_print is registered for printk.
-+ The console_lock must be held when we get here.
-+-------------------------------------------------------------------------- */
-+static void bcm_console_print (struct console * cons, const char * str,
-+ unsigned int count)
-+{
-+ unsigned int i;
-+ //_puts(str);
-+ for(i=0; i<count; i++, str++)
-+ {
-+ _putc(*str);
-+ if (*str == 10)
-+ {
-+ _putc(13);
-+ }
-+ }
-+}
+
-+static struct tty_driver * bcm_console_device(struct console * c, int *index)
-+{
-+ *index = c->index;
-+ return serial_driver;
-+}
++#
++# Common Firmware Environment
++#
++core-$(CONFIG_CFE) += arch/mips/cfe/
+
-+static int __init bcm_console_setup(struct console * co, char * options)
++#
+ # Acer PICA 61, Mips Magnum 4000 and Olivetti M700.
+ #
+ core-$(CONFIG_MACH_JAZZ) += arch/mips/jazz/
+diff -urN linux-2.6.19/arch/mips/kernel/cpu-probe.c linux-2.6.19.new/arch/mips/kernel/cpu-probe.c
+--- linux-2.6.19/arch/mips/kernel/cpu-probe.c 2006-11-29 22:57:37.000000000 +0100
++++ linux-2.6.19.new/arch/mips/kernel/cpu-probe.c 2006-12-16 18:46:31.000000000 +0100
+@@ -602,6 +602,25 @@
+ return;
+ }
+
++static inline void cpu_probe_broadcom(struct cpuinfo_mips *c)
+{
-+ return 0;
++ decode_configs(c);
++ switch (c->processor_id & 0xff00) {
++ case PRID_IMP_BCM6338:
++ c->cputype = CPU_BCM6338;
++ break;
++ case PRID_IMP_BCM6345:
++ c->cputype = CPU_BCM6345;
++ break;
++ case PRID_IMP_BCM6348:
++ c->cputype = CPU_BCM6348;
++ break;
++ default:
++ c->cputype = CPU_UNKNOWN;
++ break;
++ }
+}
+
-+static struct console bcm_sercons = {
-+ .name = "ttyS",
-+ .write = bcm_console_print,
-+ .device = bcm_console_device,
-+ .setup = bcm_console_setup,
-+ .flags = CON_PRINTBUFFER,
-+ .index = -1,
-+};
-+
-+static int __init bcm63xx_console_init(void)
-+{
-+ register_console(&bcm_sercons);
-+ return 0;
-+}
+ static inline void cpu_probe_mips(struct cpuinfo_mips *c)
+ {
+ decode_configs(c);
+@@ -736,6 +755,9 @@
+ case PRID_COMP_LEGACY:
+ cpu_probe_legacy(c);
+ break;
++ case PRID_COMP_BROADCOM:
++ cpu_probe_broadcom(c);
++ break;
+ case PRID_COMP_MIPS:
+ cpu_probe_mips(c);
+ break;
+diff -urN linux-2.6.19/arch/mips/kernel/proc.c linux-2.6.19.new/arch/mips/kernel/proc.c
+--- linux-2.6.19/arch/mips/kernel/proc.c 2006-11-29 22:57:37.000000000 +0100
++++ linux-2.6.19.new/arch/mips/kernel/proc.c 2006-12-16 18:46:31.000000000 +0100
+@@ -84,6 +84,9 @@
+ [CPU_VR4181A] = "NEC VR4181A",
+ [CPU_SR71000] = "Sandcraft SR71000",
+ [CPU_PR4450] = "Philips PR4450",
++ [CPU_BCM6338] = "BCM6338",
++ [CPU_BCM6345] = "BCM6345",
++ [CPU_BCM6348] = "BCM6348",
+ };
+
+
+diff -urN linux-2.6.19/arch/mips/mm/c-r4k.c linux-2.6.19.new/arch/mips/mm/c-r4k.c
+--- linux-2.6.19/arch/mips/mm/c-r4k.c 2006-11-29 22:57:37.000000000 +0100
++++ linux-2.6.19.new/arch/mips/mm/c-r4k.c 2006-12-16 18:46:31.000000000 +0100
+@@ -852,6 +852,13 @@
+ if (!(config & MIPS_CONF_M))
+ panic("Don't know how to probe P-caches on this cpu.");
+
++ if (c->cputype == CPU_BCM6338 || c->cputype == CPU_BCM6345 || c->cputype == CPU_BCM6348)
++ {
++ printk("bcm963xx: enabling icache and dcache...\n");
++ /* Enable caches */
++ write_c0_diag(read_c0_diag() | 0xC0000000);
++ }
+
-+console_initcall(bcm63xx_console_init);
+ /*
+ * So we seem to be a MIPS32 or MIPS64 CPU
+ * So let's probe the I-cache ...
+diff -urN linux-2.6.19/arch/mips/mm/tlbex.c linux-2.6.19.new/arch/mips/mm/tlbex.c
+--- linux-2.6.19/arch/mips/mm/tlbex.c 2006-11-29 22:57:37.000000000 +0100
++++ linux-2.6.19.new/arch/mips/mm/tlbex.c 2006-12-16 18:46:31.000000000 +0100
+@@ -880,6 +880,9 @@
+ case CPU_4KSC:
+ case CPU_20KC:
+ case CPU_25KF:
++ case CPU_BCM6338:
++ case CPU_BCM6345:
++ case CPU_BCM6348:
+ tlbw(p);
+ break;
+
+diff -urN linux-2.6.19/arch/mips/pci/Makefile linux-2.6.19.new/arch/mips/pci/Makefile
+--- linux-2.6.19/arch/mips/pci/Makefile 2006-11-29 22:57:37.000000000 +0100
++++ linux-2.6.19.new/arch/mips/pci/Makefile 2006-12-16 18:48:18.000000000 +0100
+@@ -17,6 +17,7 @@
+ obj-$(CONFIG_PCI_VR41XX) += ops-vr41xx.o pci-vr41xx.o
+ obj-$(CONFIG_NEC_CMBVR4133) += fixup-vr4133.o
+ obj-$(CONFIG_MARKEINS) += ops-emma2rh.o pci-emma2rh.o fixup-emma2rh.o
++obj-$(CONFIG_BCM963XX) += fixup-bcm96348.o pci-bcm96348.o ops-bcm96348.o
+
+ #
+ # These are still pretty much in the old state, watch, go blind.
diff -urN linux-2.6.19/include/asm-mips/bootinfo.h linux-2.6.19.new/include/asm-mips/bootinfo.h
--- linux-2.6.19/include/asm-mips/bootinfo.h 2006-11-29 22:57:37.000000000 +0100
+++ linux-2.6.19.new/include/asm-mips/bootinfo.h 2006-12-16 18:46:31.000000000 +0100
/*
* ISA Level encodings
-diff -urN linux-2.6.19/include/asm-mips/mach-bcm963xx/cpu-feature-overrides.h linux-2.6.19.new/include/asm-mips/mach-bcm963xx/cpu-feature-overrides.h
---- linux-2.6.19/include/asm-mips/mach-bcm963xx/cpu-feature-overrides.h 1970-01-01 01:00:00.000000000 +0100
-+++ linux-2.6.19.new/include/asm-mips/mach-bcm963xx/cpu-feature-overrides.h 2006-12-16 18:52:30.000000000 +0100
-@@ -0,0 +1,36 @@
-+#ifndef __ASM_MACH_BCM963XX_CPU_FEATURE_OVERRIDES_H
-+#define __ASM_MACH_BCM963XX_CPU_FEATURE_OVERRIDES_H
-+
-+#define cpu_has_tlb 1
-+#define cpu_has_4kex 4
-+#define cpu_has_4ktlb 8
-+#define cpu_has_fpu 0
-+#define cpu_has_32fpr 0
-+#define cpu_has_counter 0x40
-+#define cpu_has_watch 0
-+#define cpu_has_mips16 0
-+#define cpu_has_divec 0x200
-+#define cpu_has_vce 0
-+#define cpu_has_cache_cdex_p 0
-+#define cpu_has_cache_cdex_s 0
-+#define cpu_has_prefetch 0x40000
-+#define cpu_has_mcheck 0x2000
-+#define cpu_has_ejtag 0x4000
-+#define cpu_has_llsc 0x10000
-+#define cpu_has_vtag_icache 0
-+#define cpu_has_dc_aliases 0
-+#define cpu_has_ic_fills_f_dc 0
-+
-+#define cpu_has_nofpuex 0
-+#define cpu_has_64bits 0
-+#define cpu_has_64bit_zero_reg 0
-+#define cpu_has_64bit_gp_regs 0
-+#define cpu_has_64bit_addresses 0
-+
-+#define cpu_has_subset_pcaches 0
-+
-+#define cpu_dcache_line_size() 16
-+#define cpu_icache_line_size() 16
-+#define cpu_scache_line_size() 0
-+
-+#endif /* __ASM_MACH_BCM963XX_CPU_FEATURE_OVERRIDES_H */
diff -urN linux-2.6.19/include/asm-mips/module.h linux-2.6.19.new/include/asm-mips/module.h
--- linux-2.6.19/include/asm-mips/module.h 2006-11-29 22:57:37.000000000 +0100
+++ linux-2.6.19.new/include/asm-mips/module.h 2006-12-16 19:03:22.000000000 +0100
projects / openwrt.git / blobdiff