X-Git-Url: https://git.rohieb.name/openwrt.git/blobdiff_plain/b7a5a29ecb22d80d8a68951f207967c8437dc2e1..eba0280e05b43a0a12b2fff0b6deb38cf338a509:/scripts/flash.sh

diff --git a/scripts/flash.sh b/scripts/flash.sh
old mode 100644
new mode 100755
index aedb25072..8841c3568
--- a/scripts/flash.sh
+++ b/scripts/flash.sh
@@ -1,9 +1,9 @@
 #!/bin/bash
-
-# flash script for linksys and asus routers 
+#
+# tftp flash script for wireless routers 
 #
 # Copyright (C) 2004 by Oleg I. Vdovikin <oleg@cs.msu.su>
-# Copyright (C) 2005 by Waldemar Brodkorb <wbx@dass-it.de>
+# Copyright (C) 2005 by Waldemar Brodkorb <wbx@openwrt.org>
 #
 # This program is free software; you can redistribute it and/or modify
 # it under the terms of the GNU General Public License as published by
@@ -24,20 +24,28 @@ if [ -z "$1" ] || [ ! -f $1 ] || [ -z $2 ]; then
     echo Usage: $0 firmware vendor
 cat << EOF
 IMPORTANT:
-Notes for Linksys Routers: 
+Notes for Linksys / Asus WL500gx router: 
    be sure you have set boot_wait to yes. Power on your router
    after executing this script.
-   Use openwrt-gs-code.bin or openwrt-g-code.bin as firmware.
  
-Notes for Asus Routers:
-   be sure POWER led is flashing (If this is not a case
+Notes for Asus WL500g router:
+   be sure POWER led is flashing (If this is not the case
    poweroff the device, push the reset button & power on
    it again, then release button)
-   Use openwrt-linux.trx as firmware.
 
 1) connect your pc to the LAN port
 2) be sure your link is up and has an address in the
    192.168.1.0/24 address range (and not the 192.168.1.1)
+
+Notes for Toshiba router:
+   boot_wait is enabled by default on these units.
+
+1) connect your pc to any of the four LAN ports
+2) be sure your link is up and has an address in the
+   192.168.10.1/24 address range (and not the 192.168.10.1)
+3) run this script (unit will only accept .trx images)
+4) Turn unit power on.
+
 EOF
     exit 0
 fi
@@ -50,5 +58,9 @@ echo Please wait until leds stops flashing.
 elif [ "$2" == "linksys" ]; then
 echo Flashing 192.168.1.1 using $1...
 echo -en "rexmt 1\ntrace\nbinary\nput $1\nquit\n" | tftp 192.168.1.1
-echo Please wait until power led stops flashing. Then you can login via telnet 192.168.1.1
+echo Please wait until power led stops flashing. Do not poweroff! Then you can login via telnet 192.168.1.1.
+elif [ "$2" == "toshiba" ]; then
+echo Flashing 192.168.10.1 using $1...
+echo -en "rexmt 1\ntrace\nbinary\nput $1\nquit\n" | tftp 192.168.10.1
+echo Unit will automatically reboot within 5 minutes.  Do not power off.  Then you can login via telnet 192.168.10.1.
 fi