This patch adds support for the Sitecom WL-341 v3 and other Sercomm
IP1006RRv2 based boards for sysupgrade support and for the initial
flash through pushbutton initiated recovery mode with the special
partition table and fixes for the quirks and things required by the
modified bootloader.
There is a known bug, Wi-Fi is not working on my board probably
because of the lack of RAM (the board only has 16MiB ram -- half of
the normal amount for non rebadged versions, but there is an empty
slot for another ram chip,) but I don't know for sure. The driver
loads but hostapd fails to load so I think it's not related to the
specific device except for the lack of RAM.
Moreover, only 7 of the 11 onboard leds are confirmed working, it
seems that one of the others is always on and the remaining ones are
connected to the wireless card leds already recognized by OpenWrt
[juhosg: reordered some parts in order to keep things sorted
alphabetically]
Signed-off-by: Marco Antonio Mauro <marcus90@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29910
3c298f89-4303-0410-b956-
a3cf2f4a3e73
rt2x00_eeprom_extract "factory" 0 272
;;
+ wl341v3)
+ rt2x00_eeprom_extract "board-nvram" 64880 272
+ ;;
+
*)
rt2x00_eeprom_die "board $board is not supported yet"
;;
wan_mac=$(ramips_get_mac_binary factory 40)
;;
+ wl341v3)
+ lan_mac=$(ramips_get_mac_binary board-nvram 65440)
+ wan_mac=$(/usr/sbin/maccalc add "$lan_mac" 1)
+ ;;
+
wli-tx4-ag300n)
lan_mac=$(ramips_get_mac_binary factory 4)
;;
mac=$(ramips_get_mac_binary factory 40)
ifconfig eth0 hw ether $mac 2>/dev/null
;;
+ wl341v3)
+ mac=$(ramips_get_mac_binary board-nvram 65440)
+ ifconfig eth0 hw ether $mac 2>/dev/null
+ ;;
esac
}
*"WHR-G300N")
name="whr-g300n"
;;
+ *"Sitecom WL-341 v3")
+ name="wl341v3"
+ ;;
*"Sitecom WL-351 v1 002")
name="wl-351"
;;
rt-n15 | \
w502u |\
v22rw-2x2 | \
+ wl341v3 | \
wli-tx4-ag300n | \
whr-g300n |\
wr512-3gn)
RAMIPS_MACH_W502U, /* ALFA Networks W502U */
RAMIPS_MACH_WCR150GN, /* Sparklan WCR-150GN */
RAMIPS_MACH_WHR_G300N, /* Buffalo WHR-G300N */
+ RAMIPS_MACH_WL341V3, /* Sitecom WL-341 v3 */
RAMIPS_MACH_WL351, /* Sitecom WL-351 v1 002 */
RAMIPS_MACH_WR512_3GN, /* SH-WR512NU/WS-WR512N1-like 3GN*/
};
select RALINK_DEV_GPIO_BUTTONS
select RALINK_DEV_GPIO_LEDS
+config RT305X_MACH_WL341V3
+ bool "Sitecom WL-341 v3 board support"
+ select RALINK_DEV_GPIO_BUTTONS
+ select RALINK_DEV_GPIO_LEDS
+
config RT305X_MACH_WL351
bool "Sitecom WL-351 support"
select RALINK_DEV_GPIO_BUTTONS
obj-$(CONFIG_RT305X_MACH_WCR150GN) += mach-wcr150gn.o
obj-$(CONFIG_RT305X_MACH_WHR_G300N) += mach-whr-g300n.o
obj-$(CONFIG_RT305X_MACH_WR512_3GN) += mach-wr512-3gn.o
+obj-$(CONFIG_RT305X_MACH_WL341V3) += mach-wl341v3.o
obj-$(CONFIG_RT305X_MACH_WL351) += mach-wl351.o
--- /dev/null
+/*
+ * Sitecom WL341v3 board support
+ *
+ * Copyright (C) 2012 Marco Antonio Mauro <marcus90@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+
+#include <asm/mach-ralink/machine.h>
+#include <asm/mach-ralink/dev-gpio-buttons.h>
+#include <asm/mach-ralink/dev-gpio-leds.h>
+#include <asm/mach-ralink/rt305x.h>
+#include <asm/mach-ralink/rt305x_regs.h>
+
+#include "devices.h"
+
+#define WL341V3_GPIO_LED_FIRST_AMBER 9
+#define WL341V3_GPIO_LED_FIRST_BLUE 13
+#define WL341V3_GPIO_LED_THIRD_AMBER 11
+#define WL341V3_GPIO_LED_THIRD_BLUE 14
+#define WL341V3_GPIO_LED_FOURTH_BLUE 10
+#define WL341V3_GPIO_LED_FIFTH_AMBER 12
+#define WL341V3_GPIO_LED_FIFTH_BLUE 8
+
+#define WL341V3_GPIO_BUTTON_WPS 5 /* active low */
+#define WL341V3_GPIO_BUTTON_RESET 7 /* active low */
+
+#define WL341V3_BUTTONS_POLL_INTERVAL 20
+
+#ifdef CONFIG_MTD_PARTITIONS
+static struct mtd_partition wl341v3_partitions[] = {
+ {
+ .name = "u-boot",
+ .offset = 0,
+ .size = 0x020000,
+ .mask_flags = MTD_WRITEABLE,
+ }, {
+ .name = "board-nvram",
+ .offset = 0x020000,
+ .size = 0x010000,
+ .mask_flags = MTD_WRITEABLE,
+ }, {
+ .name = "u-boot-env",
+ .offset = 0x030000,
+ .size = 0x010000,
+ .mask_flags = MTD_WRITEABLE,
+ }, {
+ .name = "kernel",
+ .offset = 0x040000,
+ .size = 0x0d0000,
+ }, {
+ .name = "rootfs",
+ .offset = 0x110000,
+ .size = 0x2e0000,
+ }, {
+ .name = "signature-eRcOmM",
+ .offset = 0x3f0000,
+ .size = 0x010000,
+ }, {
+ .name = "firmware",
+ .offset = 0x040000,
+ .size = 0x3b0000,
+ }, {
+ .name = "fullflash",
+ .offset = 0x000000,
+ .size = 0x400000,
+ }
+};
+#endif /* CONFIG_MTD_PARTITIONS */
+
+static struct physmap_flash_data wl341v3_flash_data = {
+#ifdef CONFIG_MTD_PARTITIONS
+ .nr_parts = ARRAY_SIZE(wl341v3_partitions),
+ .parts = wl341v3_partitions,
+#endif
+};
+
+static struct gpio_led wl341v3_leds_gpio[] __initdata = {
+ {
+ .name = "wl341v3:amber:first",
+ .gpio = WL341V3_GPIO_LED_FIRST_AMBER,
+ .active_low = 1,
+ }, {
+ .name = "wl341v3:blue:first",
+ .gpio = WL341V3_GPIO_LED_FIRST_BLUE,
+ .active_low = 1,
+ }, {
+ .name = "wl341v3:amber:third",
+ .gpio = WL341V3_GPIO_LED_THIRD_AMBER,
+ .active_low = 1,
+ }, {
+ .name = "wl341v3:blue:third",
+ .gpio = WL341V3_GPIO_LED_THIRD_BLUE,
+ .active_low = 1,
+ }, {
+ .name = "wl341v3:blue:fourth",
+ .gpio = WL341V3_GPIO_LED_FOURTH_BLUE,
+ .active_low = 1,
+ }, {
+ .name = "wl341v3:amber:fifth",
+ .gpio = WL341V3_GPIO_LED_FIFTH_AMBER,
+ .active_low = 1,
+ }, {
+ .name = "wl341v3:blue:fifth",
+ .gpio = WL341V3_GPIO_LED_FIFTH_BLUE,
+ .active_low = 1,
+ }
+};
+
+static struct gpio_button wl341v3_gpio_buttons[] __initdata = {
+ {
+ .desc = "reset",
+ .type = EV_KEY,
+ .code = KEY_RESTART,
+ .threshold = 3,
+ .gpio = WL341V3_GPIO_BUTTON_RESET,
+ .active_low = 1,
+ }, {
+ .desc = "wps",
+ .type = EV_KEY,
+ .code = KEY_WPS_BUTTON,
+ .threshold = 3,
+ .gpio = WL341V3_GPIO_BUTTON_WPS,
+ .active_low = 1,
+ }
+};
+
+static void __init wl341v3_init(void)
+{
+ rt305x_gpio_init(RT305X_GPIO_MODE_GPIO << RT305X_GPIO_MODE_UART0_SHIFT);
+
+ rt305x_register_flash(0, &wl341v3_flash_data);
+ rt305x_esw_data.vlan_config = RT305X_ESW_VLAN_CONFIG_WLLLL;
+ rt305x_register_ethernet();
+ ramips_register_gpio_leds(-1, ARRAY_SIZE(wl341v3_leds_gpio),
+ wl341v3_leds_gpio);
+ ramips_register_gpio_buttons(-1, WL341V3_BUTTONS_POLL_INTERVAL,
+ ARRAY_SIZE(wl341v3_gpio_buttons),
+ wl341v3_gpio_buttons);
+ rt305x_register_wifi();
+ rt305x_register_wdt();
+ rt305x_register_usb();
+}
+
+MIPS_MACHINE(RAMIPS_MACH_WL341V3, "WL341V3", "Sitecom WL-341 v3",
+ wl341v3_init);
fi; fi
endef
+define BuildFirmware/WL341V3
+ $(call PatchKernelLzma,$(2),$(3) $($(4)))
+ $(call MkImage,lzma,"$(KDIR)/vmlinux-$(2).bin.lzma","$(KDIR)/vmlinux-$(2).uImage")
+ if [ `stat -c%s "$(KDIR)/vmlinux-$(2).uImage"` -gt $(5) ]; then \
+ echo "Warning: $(KDIR)/vmlinux-$(2).uImage is too big"; \
+ else if [ `stat -c%s $(KDIR)/root.$(1)` -gt $(6) ]; then \
+ echo "Warning: $(KDIR)/root.$(1) is too big"; \
+ else \
+ ( \
+ dd if=/dev/zero bs=195936 count=1; \
+ echo "1.01"; \
+ dd if=/dev/zero bs=581 count=1; \
+ echo -n -e "\x73\x45\x72\x43\x6F\x4D\x6D\x00\x01\x00\x00\x59\x4E\x37\x95\x58\x10\x00\x20\x00\x28\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x11\x03\x00\x00\x80\x00\x00\x00\x00\x03\x00\x00\x10\x12\x00\x00\x00\x10\x73\x45\x72\x43\x6F\x4D\x6D"; \
+ dd if=/dev/zero bs=65552 count=1; \
+ dd if=$(KDIR)/vmlinux-$(2).uImage bs=$(5) conv=sync; \
+ dd if=$(KDIR)/root.$(1) bs=64k conv=sync; \
+ dd if=/dev/zero bs=`expr 4194304 - 262144 - 16 - $(5) - \( \( \( \`stat -c%s $(KDIR)/root.$(1)\` / 65536 \) + 1 \) \* 65536 \)` count=1; \
+ echo -n -e "\x11\x03\x80\x00\x10\x12\x90\xF7\x65\x52\x63\x4F\x6D\x4D\x00\x00"; \
+ ) > $(call imgname,$(1),$(2))-factory.bin; \
+ fi; fi
+endef
+
define BuildFirmware/Buffalo
$(call PatchKernelLzma,$(2),board=$(3) $($(4)))
$(call MkImage,lzma,"$(KDIR)/vmlinux-$(2).bin.lzma","$(KDIR)/vmlinux-$(2).uImage")
$(call BuildFirmware/Generic,$(1),$(2),board=$(3) console=$(console_OMNIEMB),mtdlayout_OMNIEMB,1048576,7012352)
endef
+mtdlayout_sercomm_4M=mtdparts=physmap-flash.0:128k(u-boot)ro,64k(board-nvram)ro,64k(u-boot-env)ro,832k(kernel),2944k(rootfs),64k(signature-eRcOmM),3776k@0x40000(firmware),4096k@0x0(fullflash)
+define Image/Build/Template/WL341V3
+ $(call BuildFirmware/Generic,$(1),$(2),board=$(3),mtdlayout_sercomm_4M,851968,3014656)
+ $(call BuildFirmware/WL341V3,$(1),$(2),board=$(3),mtdlayout_sercomm_4M,851968,3014656)
+endef
+
+define Image/Build/Profile/WL341V3
+ $(call Image/Build/Template/WL341V3,$(1),wl341v3,WL341V3)
+endef
+
define Image/Build/Profile/DIR300B1
$(call Image/Build/Template/DIR300B1,$(1),dir-300-b1,DIR-300-B1,wrgn23_dlwbr_dir300b)
$(call Image/Build/Template/DIR300B1,$(1),dir-600-b1,DIR-600-B1,wrgn23_dlwbr_dir600b)
$(call Image/Build/Profile/MOFI35003GN,$(1))
$(call Image/Build/Profile/W502U,$(1))
$(call Image/Build/Profile/WR5123GN,$(1))
+ $(call Image/Build/Profile/WL341V3,$(1))
$(call Image/Build/Profile/WL351,$(1))
endef
endif
CONFIG_RT305X_MACH_W502U=y
CONFIG_RT305X_MACH_WCR150GN=y
CONFIG_RT305X_MACH_WHR_G300N=y
+CONFIG_RT305X_MACH_WL341V3=y
CONFIG_RT305X_MACH_WL351=y
CONFIG_RT305X_MACH_WR512_3GN=y
# CONFIG_SCSI_DMA is not set
projects / openwrt.git / commitdiff