Eine Seite um (gute) Beispielkonfigkurationen zu sammeln, am besten mit Beispieldruck (Foto)
Es gibt vermutlich nicht ''die eine Ideal-Konfiguration'' die für alle Teile gut funktioniert, mit den hier gelisteten sollte aber ein Druck einigermaßen gelingen.
===== Von larsan =====
Ursprünglich die erste Konfiguration für unseren Drucker auf Basis von {{Benutzer|DanielWillmann}}s Konfiguration.
Von der unten stehenden Config gibt es eine verbesserte [https://rohieb.name/stuff/stratum0/larsan-tuned.ini larsan-tuned.ini], die Rohieb gemacht hat.
# generated by Slic3r 0.9.8-dev on Wed Nov 28 08:03:30 2012
acceleration = 0
bed_size = 180,200
bed_temperature = 50
bottom_solid_layers = 3
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 0
complete_objects =
cooling =
disable_fan_first_layers = 1
duplicate = 1
duplicate_distance = 6
duplicate_grid = 1,1
end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors
external_perimeter_speed = 40%
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 30
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 1.75
fill_angle = 0
fill_density = 0.15
fill_pattern = honeycomb
first_layer_bed_temperature = 50
first_layer_extrusion_width = 0
first_layer_height = 0.27
first_layer_speed = 15%
first_layer_temperature = 195
g0 = 0
gap_fill_speed = 20
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_speed = 60
layer_gcode =
layer_height = 0.24
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 5
min_skirt_length = 0
notes = larsanconfig
nozzle_diameter = 0.35
only_retract_when_crossing_perimeters =
output_filename_format = [input_filename_base].gcode
perimeter_acceleration = 25
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 50
perimeters = 3
post_process =
print_center = 90,100
randomize_start = 1
retract_before_travel = 5
retract_length = 2
retract_length_toolchange = 3
retract_lift = 0
retract_restart_extra = 0.01
retract_restart_extra_toolchange = 0
retract_speed = 50
rotate = 0
scale = 1
skirt_distance = 20
skirt_height = 1
skirts = 3
slowdown_below_layer_time = 50
small_perimeter_speed = 100%
solid_fill_pattern = rectilinear
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_speed = 90%
start_gcode = G28 ; home all axes\nM92 E820
support_material =
support_material_angle = 45
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 60
support_material_threshold = 41
temperature = 185
threads = 2
top_solid_infill_speed = 70%
top_solid_layers = 3
travel_speed = 50
use_relative_e_distances = 0
vibration_limit = 0
z_offset = 0
== Schnelle Config von [[Benutzer:Daniel Bohrer|Daniel Bohrer]] (Work in Progress) ==
Der erste und letzte Layer wird "normal schnell" gedruckt, die anderen doppelt so schnell. Bei dünnen Strukturen (z.B. Mate-Tags) muss man notfalls noch ein bisschen mit der Perimeteranzahl spielen.
# generated by Slic3r 0.9.4-dev on Fri Nov 16 20:55:02 2012
acceleration = 0
bed_size = 180,200
bed_temperature = 60
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 350
brim_width = 0
complete_objects = 0
cooling = 1
disable_fan_first_layers = 1
duplicate = 1
duplicate_distance = 6
duplicate_grid = 1,1
end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors
external_perimeter_speed = 90%
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1.0
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 1.75
fill_angle = 0
fill_density = 0.2
fill_pattern = rectilinear
first_layer_bed_temperature = 60
first_layer_extrusion_width = 0
first_layer_height = 100%
first_layer_speed = 20%
first_layer_temperature = 195
g0 = 0
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_speed = 120
layer_gcode =
layer_height = 0.25
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
notes = Used for Mate name tag
nozzle_diameter = 0.35
only_retract_when_crossing_perimeters = 0
output_filename_format = [input_filename_base].gcode
perimeter_acceleration = 25
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 100
perimeters = 2
post_process =
print_center = 90,100
randomize_start = 1
retract_before_travel = 4
retract_length = 4
retract_length_toolchange = 3
retract_lift = 0.5
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 150
rotate = 0
scale = 1
skirt_distance = 10
skirt_height = 1
skirts = 2
slowdown_below_layer_time = 60
small_perimeter_speed = 80%
solid_fill_pattern = rectilinear
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_speed = 100%
solid_layers = 3
start_gcode = G28 ; home all axes\nM92 E820
support_material = 1
support_material_angle = 45
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_pattern = rectilinear
support_material_spacing = 3
support_material_threshold = 45
temperature = 185
threads = 3
top_solid_infill_speed = 50%
travel_speed = 140
use_relative_e_distances = 0
z_offset = 0.22
== von Chrissi^ ==
* Nette Konfiguration zum Drucken von allem möglichen.
* First Layer ist super langsam => Guter Druck auch bei kleinen Strukturen
* First Layer Extrusion Width 110% => Wenig ''Wellenschlagen'' auf dem ersten Layer
# generated by Slic3r 0.9.3 on Tue Nov 6 21:53:43 2012
acceleration = 0
bed_size = 180,200
bed_temperature = 60
bridge_fan_speed = 100
bridge_flow_ratio = 1.05
bridge_speed = 60
brim_width = 0
complete_objects =
cooling = 1
disable_fan_first_layers = 1
duplicate = 1
duplicate_distance = 6
duplicate_grid = 1,1
end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors
external_perimeter_speed = 100%
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 30
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 100%
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 1.75
fill_angle = 45
fill_density = 0.1
fill_pattern = rectilinear
first_layer_bed_temperature = 60
first_layer_extrusion_width = 112%
first_layer_height = 95%
first_layer_speed = 15%
first_layer_temperature = 200
g0 = 0
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 120%
infill_speed = 60
layer_gcode =
layer_height = 0.3
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 5
notes = larsanconfig
nozzle_diameter = 0.35
only_retract_when_crossing_perimeters = 1
output_filename_format = [timestamp]_[input_filename_base].gcode
perimeter_acceleration = 25
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 60
perimeters = 2
post_process =
print_center = 120,120
randomize_start = 1
retract_before_travel = 4
retract_length = 2
retract_length_toolchange = 3
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 50
rotate = 0
scale = 1
skirt_distance = 10
skirt_height = 1
skirts = 3
slowdown_below_layer_time = 50
small_perimeter_speed = 50%
solid_fill_pattern = rectilinear
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_speed = 100%
solid_layers = 3
start_gcode = G28 ; home all axes\nM92 E820
support_material = 1
support_material_angle = 45
support_material_extruder = 1
support_material_extrusion_width = 160%
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_threshold = 40
temperature = 205
threads = 2
top_solid_infill_speed = 40%
travel_speed = 90
use_relative_e_distances = 0
z_offset = 0
== Gelbes Filament ==
* Ursprünglich für [[Reprap/Parent]] erstellt
* Damit gedruckt: der letzte gelbe frame-vertex für den Drucker
* etwas wärmer (195°C)
* 0.22 mm z-offeset
acceleration = 0
bed_size = 170,170
bed_temperature = 60
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 30
brim_width = 0
complete_objects = 0
cooling = 1
disable_fan_first_layers = 1
duplicate = 1
duplicate_distance = 6
duplicate_grid = 1,1
end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors
external_perimeter_speed = 90%
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 3
fill_angle = 45
fill_density = 0.15
fill_pattern = rectilinear
first_layer_bed_temperature = 60
first_layer_extrusion_width = 0
first_layer_height = 115%
first_layer_speed = 80%
first_layer_temperature = 200
g0 = 0
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_speed = 40
layer_gcode =
layer_height = 0.28
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
notes = Used for Mate name tag
nozzle_diameter = 0.35
output_filename_format = [input_filename_base].gcode
perimeter_acceleration = 25
perimeter_speed = 30
perimeters = 3
perimeters_extruder = 1
perimeters_extrusion_width = 0
post_process =
print_center = 50,27
randomize_start = 1
retract_before_travel = 4
retract_length = 3
retract_lift = 0.4
retract_restart_extra = 0
retract_speed = 30
rotate = 0
scale = 1
skirt_distance = 6
skirt_height = 1
skirts = 3
slowdown_below_layer_time = 60
small_perimeter_speed = 30
solid_fill_pattern = rectilinear
solid_infill_speed = 40
solid_layers = 3
start_gcode = G28 ; home all axes\nM92 E820
support_material =
support_material_angle = 45
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_threshold = 45
temperature = 195
threads = 2
top_solid_infill_speed = 40
travel_speed = 130
use_relative_e_distances = 0
z_offset = 0.22
== RepRap-Config ==
Konfiguration, mit der die Teile für den RepRap vom [http://netz39.eu Netz39] gedruckt wurden.
# generated by Slic3r 0.9.9-dev on Mon Jun 3 17:06:48 2013
avoid_crossing_perimeters = 0
bed_size = 180,200
bed_temperature = 50
bottom_solid_layers = 5
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 30
brim_width = 0
complete_objects = 1
cooling =
default_acceleration = 0
disable_fan_first_layers = 1
duplicate = 1
duplicate_distance = 6
duplicate_grid = 1,1
end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors
external_perimeter_speed = 40%
external_perimeters_first = 0
extra_perimeters =
extruder_clearance_height = 35
extruder_clearance_radius = 62
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1.1
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 1.75
fill_angle = 30
fill_density = 0.5
fill_pattern = rectilinear
first_layer_bed_temperature = 50
first_layer_extrusion_width = 0
first_layer_height = 150%
first_layer_speed = 40%
first_layer_temperature = 197
g0 = 0
gap_fill_speed = 20
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 60
layer_gcode =
layer_height = 0.2
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 5
min_skirt_length = 15
notes = config for printing netz39 pieces
nozzle_diameter = 0.33
only_retract_when_crossing_perimeters = 1
output_filename_format = [input_filename_base].gcode
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 60
perimeters = 3
post_process =
print_center = 90,100
raft_layers = 0
randomize_start =
resolution = 0
retract_before_travel = 0
retract_layer_change = 1
retract_length = 2
retract_length_toolchange = 5
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 50
rotate = 0
scale = 1
skirt_distance = 5
skirt_height = 1
skirts = 2
slowdown_below_layer_time = 50
small_perimeter_speed = 60%
solid_fill_pattern = rectilinear
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 100%
start_gcode = G28 ; home all axes\nM92 E820
support_material =
support_material_angle = 45
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 60
support_material_threshold = 41
temperature = 188
threads = 2
toolchange_gcode =
top_infill_extrusion_width = 0
top_solid_infill_speed = 70%
top_solid_layers = 5
travel_speed = 100
use_relative_e_distances = 0
vibration_limit = 0
z_offset = 0
[[Kategorie:RepRap]]