Eine Seite um (gute) Beispielkonfigkurationen zu sammeln, am besten mit Beispieldruck (Foto) Es gibt vermutlich nicht ''die eine Ideal-Konfiguration'' die für alle Teile gut funktioniert, mit den hier gelisteten sollte aber ein Druck einigermaßen gelingen. === aktuelle configs === Der Drucker hat sich verändert, dementsprechend haben sich auch die configs geändert. Beispielsweise haben wir jetzt 0.5 mm Düsen an den beiden Hot Ends, nicht mehr 0.35 mm. Dazu kommt, dass das homing konstruktionsbedingt außerhalb des hot beds stattfindet, mit diesem Start-gcode wird das ausgeglichen: G28 X0 Y0 ; home X and Y G0 X60; move to X60 G92 X0; set postition to X=0 G28 Z0; home Z Das, oder etwas Ähnliches sollte in allen configs mit drin sein. Eine funktionierende, aber noch nicht sehr fein justierte config ist diese: ==== larsan ====
# generated by Slic3r 0.9.10 on Sun Sep 29 22:51:39 2013 avoid_crossing_perimeters = 0 bed_size = 190,190 bed_temperature = 50 bottom_solid_layers = 3 bridge_acceleration = 0 bridge_fan_speed = 100 bridge_flow_ratio = 1 bridge_speed = 60 brim_width = 0 complete_objects = 1 cooling = 1 default_acceleration = 0 disable_fan_first_layers = 1 duplicate = 1 duplicate_distance = 6 duplicate_grid = 1,1 end_gcode = M104 S0 ; turn off extruder temperature\n;M140 S0 ; turn off bed temperature; currently disabled\nG0 X0 ; move X axis to 0\nG92 Z0 E5 ;define current point as Z0 E5\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y198 F6000 ; drive print table all the way out\nM84 ; disable motors external_perimeter_speed = 70% external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 1 extruder_clearance_radius = 30 extruder_offset = 0x0 extrusion_axis = E extrusion_multiplier = 1 extrusion_width = 180% fan_always_on = 0 fan_below_layer_time = 60 filament_diameter = 1.75 fill_angle = 45 fill_density = 0.3 fill_pattern = honeycomb first_layer_bed_temperature = 50 first_layer_extrusion_width = 0 first_layer_height = 0.25 first_layer_speed = 30% first_layer_temperature = 200 g0 = 0 gap_fill_speed = 15 gcode_arcs = 0 gcode_comments = 0 gcode_flavor = reprap infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_speed = 60 layer_gcode = layer_height = 0.25 max_fan_speed = 100 min_fan_speed = 35 min_print_speed = 5 min_skirt_length = 0 notes = larsanconfig nozzle_diameter = 0.5 only_retract_when_crossing_perimeters = 1 output_filename_format = [input_filename_base].gcode perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 80 perimeters = 3 post_process = print_center = 90,60 raft_layers = 0 randomize_start = 0 resolution = 0 retract_before_travel = 2 retract_layer_change = 1 retract_length = 2 retract_length_toolchange = 10 retract_lift = 0 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 35 rotate = 0 scale = 1 skirt_distance = 10 skirt_height = 1 skirts = 3 slowdown_below_layer_time = 30 small_perimeter_speed = 50 solid_fill_pattern = rectilinear solid_infill_below_area = 40 solid_infill_every_layers = 0 solid_infill_extrusion_width = 0 solid_infill_speed = 80 spiral_vase = 0 start_gcode = G28 X0 Y0 ; home X and Y\nG0 X60; move to X60\nG92 X0; set postition to X=0\nG28 Z0; home Z support_material = 0 support_material_angle = 0 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_layers = 0 support_material_interface_spacing = 0 support_material_pattern = rectilinear support_material_spacing = 2.5 support_material_speed = 65 support_material_threshold = 0 temperature = 195 threads = 1 toolchange_gcode = top_infill_extrusion_width = 0 top_solid_infill_speed = 60 top_solid_layers = 3 travel_speed = 80 use_relative_e_distances = 0 vibration_limit = 0 wipe = 0 z_offset = 0=== alte configs === ==== Von larsan ==== Ursprünglich die erste Konfiguration für unseren Drucker auf Basis von {{Benutzer|DanielWillmann}}s Konfiguration. Von der unten stehenden Config gibt es eine verbesserte [https://rohieb.name/stuff/stratum0/larsan-tuned.ini larsan-tuned.ini], die Rohieb gemacht hat.
# generated by Slic3r 0.9.8-dev on Wed Nov 28 08:03:30 2012 acceleration = 0 bed_size = 180,200 bed_temperature = 50 bottom_solid_layers = 3 bridge_fan_speed = 100 bridge_flow_ratio = 1 bridge_speed = 60 brim_width = 0 complete_objects = cooling = disable_fan_first_layers = 1 duplicate = 1 duplicate_distance = 6 duplicate_grid = 1,1 end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors external_perimeter_speed = 40% extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 30 extruder_offset = 0x0 extrusion_axis = E extrusion_multiplier = 1 extrusion_width = 0 fan_always_on = 0 fan_below_layer_time = 60 filament_diameter = 1.75 fill_angle = 0 fill_density = 0.15 fill_pattern = honeycomb first_layer_bed_temperature = 50 first_layer_extrusion_width = 0 first_layer_height = 0.27 first_layer_speed = 15% first_layer_temperature = 195 g0 = 0 gap_fill_speed = 20 gcode_arcs = 0 gcode_comments = 0 gcode_flavor = reprap infill_acceleration = 50 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0 infill_speed = 60 layer_gcode = layer_height = 0.24 max_fan_speed = 100 min_fan_speed = 35 min_print_speed = 5 min_skirt_length = 0 notes = larsanconfig nozzle_diameter = 0.35 only_retract_when_crossing_perimeters = output_filename_format = [input_filename_base].gcode perimeter_acceleration = 25 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 50 perimeters = 3 post_process = print_center = 90,100 randomize_start = 1 retract_before_travel = 5 retract_length = 2 retract_length_toolchange = 3 retract_lift = 0 retract_restart_extra = 0.01 retract_restart_extra_toolchange = 0 retract_speed = 50 rotate = 0 scale = 1 skirt_distance = 20 skirt_height = 1 skirts = 3 slowdown_below_layer_time = 50 small_perimeter_speed = 100% solid_fill_pattern = rectilinear solid_infill_below_area = 0 solid_infill_every_layers = 0 solid_infill_speed = 90% start_gcode = G28 ; home all axes\nM92 E820 support_material = support_material_angle = 45 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_pattern = rectilinear support_material_spacing = 2 support_material_speed = 60 support_material_threshold = 41 temperature = 185 threads = 2 top_solid_infill_speed = 70% top_solid_layers = 3 travel_speed = 50 use_relative_e_distances = 0 vibration_limit = 0 z_offset = 0==== Schnelle Config von [[Benutzer:Daniel Bohrer|Daniel Bohrer]] (Work in Progress) ==== Der erste und letzte Layer wird "normal schnell" gedruckt, die anderen doppelt so schnell. Bei dünnen Strukturen (z.B. Mate-Tags) muss man notfalls noch ein bisschen mit der Perimeteranzahl spielen.
# generated by Slic3r 0.9.4-dev on Fri Nov 16 20:55:02 2012 acceleration = 0 bed_size = 180,200 bed_temperature = 60 bridge_fan_speed = 100 bridge_flow_ratio = 1 bridge_speed = 350 brim_width = 0 complete_objects = 0 cooling = 1 disable_fan_first_layers = 1 duplicate = 1 duplicate_distance = 6 duplicate_grid = 1,1 end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors external_perimeter_speed = 90% extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extruder_offset = 0x0 extrusion_axis = E extrusion_multiplier = 1.0 extrusion_width = 0 fan_always_on = 0 fan_below_layer_time = 60 filament_diameter = 1.75 fill_angle = 0 fill_density = 0.2 fill_pattern = rectilinear first_layer_bed_temperature = 60 first_layer_extrusion_width = 0 first_layer_height = 100% first_layer_speed = 20% first_layer_temperature = 195 g0 = 0 gcode_arcs = 0 gcode_comments = 0 gcode_flavor = reprap infill_acceleration = 50 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0 infill_speed = 120 layer_gcode = layer_height = 0.25 max_fan_speed = 100 min_fan_speed = 35 min_print_speed = 10 notes = Used for Mate name tag nozzle_diameter = 0.35 only_retract_when_crossing_perimeters = 0 output_filename_format = [input_filename_base].gcode perimeter_acceleration = 25 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 100 perimeters = 2 post_process = print_center = 90,100 randomize_start = 1 retract_before_travel = 4 retract_length = 4 retract_length_toolchange = 3 retract_lift = 0.5 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 150 rotate = 0 scale = 1 skirt_distance = 10 skirt_height = 1 skirts = 2 slowdown_below_layer_time = 60 small_perimeter_speed = 80% solid_fill_pattern = rectilinear solid_infill_below_area = 0 solid_infill_every_layers = 0 solid_infill_speed = 100% solid_layers = 3 start_gcode = G28 ; home all axes\nM92 E820 support_material = 1 support_material_angle = 45 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_pattern = rectilinear support_material_spacing = 3 support_material_threshold = 45 temperature = 185 threads = 3 top_solid_infill_speed = 50% travel_speed = 140 use_relative_e_distances = 0 z_offset = 0.22==== Für Mate-Tags ==== Konfiguration für Mate-Tags
# generated by Slic3r 0.9.9-dev on Fri Jun 7 23:59:05 2013 avoid_crossing_perimeters = 1 bed_size = 180,200 bed_temperature = 50 bottom_solid_layers = 3 bridge_acceleration = 0 bridge_fan_speed = 100 bridge_flow_ratio = 1 bridge_speed = 50 brim_width = 0 complete_objects = 1 cooling = default_acceleration = 0 disable_fan_first_layers = 1 duplicate = 1 duplicate_distance = 6 duplicate_grid = 1,1 end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors external_perimeter_speed = 50% external_perimeters_first = 0 extra_perimeters = extruder_clearance_height = 36 extruder_clearance_radius = 40 extruder_offset = 0x0 extrusion_axis = E extrusion_multiplier = 1.1 extrusion_width = 0 fan_always_on = 0 fan_below_layer_time = 60 filament_diameter = 1.75 fill_angle = 30 fill_density = 0.3 fill_pattern = rectilinear first_layer_bed_temperature = 50 first_layer_extrusion_width = 0 first_layer_height = 0.27 first_layer_speed = 40% first_layer_temperature = 197 g0 = 0 gap_fill_speed = 20 gcode_arcs = 0 gcode_comments = 0 gcode_flavor = reprap infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_speed = 70 layer_gcode = layer_height = 0.24 max_fan_speed = 100 min_fan_speed = 35 min_print_speed = 5 min_skirt_length = 10 notes = Config used for bottle name tags (http://www.thingiverse.com/thing:38861) nozzle_diameter = 0.33 only_retract_when_crossing_perimeters = 1 output_filename_format = [input_filename_base].gcode perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 50 perimeters = 2 post_process = print_center = 90,100 raft_layers = 0 randomize_start = resolution = 0 retract_before_travel = 0 retract_layer_change = 1 retract_length = 2 retract_length_toolchange = 5 retract_lift = 0 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 50 rotate = 0 scale = 1 skirt_distance = 5 skirt_height = 1 skirts = 2 slowdown_below_layer_time = 50 small_perimeter_speed = 60% solid_fill_pattern = rectilinear solid_infill_below_area = 0 solid_infill_every_layers = 0 solid_infill_extrusion_width = 0 solid_infill_speed = 100% start_gcode = G28 ; home all axes\nM92 E820 support_material = support_material_angle = 45 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_layers = 0 support_material_interface_spacing = 0 support_material_pattern = rectilinear support_material_spacing = 2 support_material_speed = 70 support_material_threshold = 41 temperature = 188 threads = 2 toolchange_gcode = top_infill_extrusion_width = 0 top_solid_infill_speed = 70% top_solid_layers = 3 travel_speed = 50 use_relative_e_distances = 0 vibration_limit = 0 z_offset = 0==== von Chrissi^ ==== * Nette Konfiguration zum Drucken von allem möglichen. * First Layer ist super langsam => Guter Druck auch bei kleinen Strukturen * First Layer Extrusion Width 110% => Wenig ''Wellenschlagen'' auf dem ersten Layer
# generated by Slic3r 0.9.3 on Tue Nov 6 21:53:43 2012 acceleration = 0 bed_size = 180,200 bed_temperature = 60 bridge_fan_speed = 100 bridge_flow_ratio = 1.05 bridge_speed = 60 brim_width = 0 complete_objects = cooling = 1 disable_fan_first_layers = 1 duplicate = 1 duplicate_distance = 6 duplicate_grid = 1,1 end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors external_perimeter_speed = 100% extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 30 extruder_offset = 0x0 extrusion_axis = E extrusion_multiplier = 1 extrusion_width = 100% fan_always_on = 0 fan_below_layer_time = 60 filament_diameter = 1.75 fill_angle = 45 fill_density = 0.1 fill_pattern = rectilinear first_layer_bed_temperature = 60 first_layer_extrusion_width = 112% first_layer_height = 95% first_layer_speed = 15% first_layer_temperature = 200 g0 = 0 gcode_arcs = 0 gcode_comments = 0 gcode_flavor = reprap infill_acceleration = 50 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 120% infill_speed = 60 layer_gcode = layer_height = 0.3 max_fan_speed = 100 min_fan_speed = 35 min_print_speed = 5 notes = larsanconfig nozzle_diameter = 0.35 only_retract_when_crossing_perimeters = 1 output_filename_format = [timestamp]_[input_filename_base].gcode perimeter_acceleration = 25 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 60 perimeters = 2 post_process = print_center = 120,120 randomize_start = 1 retract_before_travel = 4 retract_length = 2 retract_length_toolchange = 3 retract_lift = 0 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 50 rotate = 0 scale = 1 skirt_distance = 10 skirt_height = 1 skirts = 3 slowdown_below_layer_time = 50 small_perimeter_speed = 50% solid_fill_pattern = rectilinear solid_infill_below_area = 0 solid_infill_every_layers = 0 solid_infill_speed = 100% solid_layers = 3 start_gcode = G28 ; home all axes\nM92 E820 support_material = 1 support_material_angle = 45 support_material_extruder = 1 support_material_extrusion_width = 160% support_material_pattern = rectilinear support_material_spacing = 2 support_material_threshold = 40 temperature = 205 threads = 2 top_solid_infill_speed = 40% travel_speed = 90 use_relative_e_distances = 0 z_offset = 0==== Gelbes Filament ==== * Ursprünglich für [[Reprap/Parent]] erstellt * Damit gedruckt: der letzte gelbe frame-vertex für den Drucker * etwas wärmer (195°C) * 0.22 mm z-offeset
acceleration = 0 bed_size = 170,170 bed_temperature = 60 bridge_fan_speed = 100 bridge_flow_ratio = 1 bridge_speed = 30 brim_width = 0 complete_objects = 0 cooling = 1 disable_fan_first_layers = 1 duplicate = 1 duplicate_distance = 6 duplicate_grid = 1,1 end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors external_perimeter_speed = 90% extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_axis = E extrusion_multiplier = 1 extrusion_width = 0 fan_always_on = 0 fan_below_layer_time = 60 filament_diameter = 3 fill_angle = 45 fill_density = 0.15 fill_pattern = rectilinear first_layer_bed_temperature = 60 first_layer_extrusion_width = 0 first_layer_height = 115% first_layer_speed = 80% first_layer_temperature = 200 g0 = 0 gcode_arcs = 0 gcode_comments = 0 gcode_flavor = reprap infill_acceleration = 50 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0 infill_speed = 40 layer_gcode = layer_height = 0.28 max_fan_speed = 100 min_fan_speed = 35 min_print_speed = 10 notes = Used for Mate name tag nozzle_diameter = 0.35 output_filename_format = [input_filename_base].gcode perimeter_acceleration = 25 perimeter_speed = 30 perimeters = 3 perimeters_extruder = 1 perimeters_extrusion_width = 0 post_process = print_center = 50,27 randomize_start = 1 retract_before_travel = 4 retract_length = 3 retract_lift = 0.4 retract_restart_extra = 0 retract_speed = 30 rotate = 0 scale = 1 skirt_distance = 6 skirt_height = 1 skirts = 3 slowdown_below_layer_time = 60 small_perimeter_speed = 30 solid_fill_pattern = rectilinear solid_infill_speed = 40 solid_layers = 3 start_gcode = G28 ; home all axes\nM92 E820 support_material = support_material_angle = 45 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_pattern = rectilinear support_material_spacing = 2.5 support_material_threshold = 45 temperature = 195 threads = 2 top_solid_infill_speed = 40 travel_speed = 130 use_relative_e_distances = 0 z_offset = 0.22==== RepRap-Config ==== Konfiguration, mit der die Teile für den RepRap vom [http://netz39.eu Netz39] gedruckt wurden.
# generated by Slic3r 0.9.9-dev on Mon Jun 3 17:06:48 2013 avoid_crossing_perimeters = 0 bed_size = 180,200 bed_temperature = 50 bottom_solid_layers = 5 bridge_acceleration = 0 bridge_fan_speed = 100 bridge_flow_ratio = 1 bridge_speed = 30 brim_width = 0 complete_objects = 1 cooling = default_acceleration = 0 disable_fan_first_layers = 1 duplicate = 1 duplicate_distance = 6 duplicate_grid = 1,1 end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors external_perimeter_speed = 40% external_perimeters_first = 0 extra_perimeters = extruder_clearance_height = 35 extruder_clearance_radius = 62 extruder_offset = 0x0 extrusion_axis = E extrusion_multiplier = 1.1 extrusion_width = 0 fan_always_on = 0 fan_below_layer_time = 60 filament_diameter = 1.75 fill_angle = 30 fill_density = 0.5 fill_pattern = rectilinear first_layer_bed_temperature = 50 first_layer_extrusion_width = 0 first_layer_height = 150% first_layer_speed = 40% first_layer_temperature = 197 g0 = 0 gap_fill_speed = 20 gcode_arcs = 0 gcode_comments = 0 gcode_flavor = reprap infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_speed = 60 layer_gcode = layer_height = 0.2 max_fan_speed = 100 min_fan_speed = 35 min_print_speed = 5 min_skirt_length = 15 notes = config for printing netz39 pieces nozzle_diameter = 0.33 only_retract_when_crossing_perimeters = 1 output_filename_format = [input_filename_base].gcode perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 60 perimeters = 3 post_process = print_center = 90,100 raft_layers = 0 randomize_start = resolution = 0 retract_before_travel = 0 retract_layer_change = 1 retract_length = 2 retract_length_toolchange = 5 retract_lift = 0 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 50 rotate = 0 scale = 1 skirt_distance = 5 skirt_height = 1 skirts = 2 slowdown_below_layer_time = 50 small_perimeter_speed = 60% solid_fill_pattern = rectilinear solid_infill_below_area = 0 solid_infill_every_layers = 0 solid_infill_extrusion_width = 0 solid_infill_speed = 100% start_gcode = G28 ; home all axes\nM92 E820 support_material = support_material_angle = 45 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_layers = 0 support_material_interface_spacing = 0 support_material_pattern = rectilinear support_material_spacing = 2 support_material_speed = 60 support_material_threshold = 41 temperature = 188 threads = 2 toolchange_gcode = top_infill_extrusion_width = 0 top_solid_infill_speed = 70% top_solid_layers = 5 travel_speed = 100 use_relative_e_distances = 0 vibration_limit = 0 z_offset = 0[[Kategorie:RepRap]]