-# generated by Slic3r 1.2.9 on Tue Nov 1 09:16:29 2016
+# generated by Slic3r 1.2.9 on Mon Jan 30 16:49:14 2017
-[filament:Lulzbot ABS]
-bed_temperature = 100
-bridge_fan_speed = 50
+[filament:1.75mm ABS]
+bed_temperature = 0
+bridge_fan_speed = 35
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #FFFFFF
-filament_diameter = 2.85
-first_layer_bed_temperature = 100
+filament_diameter = 1.75
+first_layer_bed_temperature = 0
first_layer_temperature = 250
max_fan_speed = 0
min_fan_speed = 0
min_print_speed = 5
-slowdown_below_layer_time = 20
+slowdown_below_layer_time = 10
temperature = 230
-[filament:Lulzbot PETG ]
-bed_temperature = 75
-bridge_fan_speed = 100
-cooling = 1
-disable_fan_first_layers = 1
-extrusion_multiplier = 1
-fan_always_on = 1
-fan_below_layer_time = 60
-filament_colour = #B1EB96
-filament_diameter = 2.85
-first_layer_bed_temperature = 75
-first_layer_temperature = 235
-max_fan_speed = 100
-min_fan_speed = 50
-min_print_speed = 10
-slowdown_below_layer_time = 30
-temperature = 235
-
-[filament:Lulzbot PLA]
+[filament:1.75mm Holz]
bed_temperature = 50
bridge_fan_speed = 100
cooling = 1
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 60
-filament_colour = #C0C0C0
-filament_diameter = 2.86
+filament_colour = #FFFFFF
+filament_diameter = 1.75
first_layer_bed_temperature = 50
first_layer_temperature = 200
max_fan_speed = 100
min_fan_speed = 50
min_print_speed = 5
-slowdown_below_layer_time = 30
-temperature = 200
+slowdown_below_layer_time = 10
+temperature = 190
-[filament:Lulzbot PLA Weiß]
+[filament:1.75mm PLA]
bed_temperature = 50
bridge_fan_speed = 100
cooling = 1
-disable_fan_first_layers = 1
+disable_fan_first_layers = 3
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #FFFFFF
-filament_diameter = 2.85
+filament_diameter = 1.75
first_layer_bed_temperature = 50
-first_layer_temperature = 200
+first_layer_temperature = 220
max_fan_speed = 100
-min_fan_speed = 30
+min_fan_speed = 100
min_print_speed = 5
-slowdown_below_layer_time = 30
-temperature = 180
+slowdown_below_layer_time = 20
+temperature = 190
-[filament:MendelPro ABS]
+[filament:1.75mm PLA TinyBoy]
bed_temperature = 0
-bridge_fan_speed = 50
-cooling = 1
-disable_fan_first_layers = 1
-extrusion_multiplier = 1
-fan_always_on = 0
-fan_below_layer_time = 60
-filament_colour = #FFFFFF
-filament_diameter = 1.7
-first_layer_bed_temperature = 0
-first_layer_temperature = 250
-max_fan_speed = 0
-min_fan_speed = 0
-min_print_speed = 5
-slowdown_below_layer_time = 30
-temperature = 230
-
-[filament:MendelPro Holz]
-bed_temperature = 50
bridge_fan_speed = 100
cooling = 1
-disable_fan_first_layers = 1
+disable_fan_first_layers = 2
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 60
-filament_colour = #FFFFFF
-filament_diameter = 1.7
-first_layer_bed_temperature = 55
+filament_colour = #FF8000
+filament_diameter = 1.75
+first_layer_bed_temperature = 0
first_layer_temperature = 200
-max_fan_speed = 100
-min_fan_speed = 50
+max_fan_speed = 40
+min_fan_speed = 35
min_print_speed = 5
-slowdown_below_layer_time = 30
-temperature = 185
+slowdown_below_layer_time = 10
+temperature = 200
-[filament:MendelPro PLA]
-bed_temperature = 50
+[filament:2.70mm PLA]
+bed_temperature = 60
bridge_fan_speed = 100
cooling = 1
-disable_fan_first_layers = 1
+disable_fan_first_layers = 3
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 60
-filament_colour = #FFFFFF
-filament_diameter = 1.7
-first_layer_bed_temperature = 50
-first_layer_temperature = 200
+filament_colour = #FF00FF
+filament_diameter = 2.72
+first_layer_bed_temperature = 60
+first_layer_temperature = 220
max_fan_speed = 100
-min_fan_speed = 50
+min_fan_speed = 100
min_print_speed = 5
-slowdown_below_layer_time = 15
-temperature = 180
+slowdown_below_layer_time = 20
+temperature = 200
-[filament:TinyBoy PLA]
-bed_temperature = 0
+[filament:2.80mm PETG ]
+bed_temperature = 75
bridge_fan_speed = 100
cooling = 1
-disable_fan_first_layers = 2
+disable_fan_first_layers = 3
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 60
-filament_colour = #FF8000
-filament_diameter = 1.75
-first_layer_bed_temperature = 0
-first_layer_temperature = 200
-max_fan_speed = 40
-min_fan_speed = 35
+filament_colour = #B1EB96
+filament_diameter = 2.8
+first_layer_bed_temperature = 75
+first_layer_temperature = 245
+max_fan_speed = 100
+min_fan_speed = 100
min_print_speed = 5
-slowdown_below_layer_time = 15
-temperature = 190
+slowdown_below_layer_time = 10
+temperature = 235
-[filament:prusa i3 ABS grün]
+[filament:2.85mm ABS]
bed_temperature = 100
-bridge_fan_speed = 70
+bridge_fan_speed = 35
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 60
-filament_colour = #80FF00
-filament_diameter = 2.9
+filament_colour = #FFFFFF
+filament_diameter = 2.85
first_layer_bed_temperature = 100
-first_layer_temperature = 255
+first_layer_temperature = 250
max_fan_speed = 0
min_fan_speed = 0
min_print_speed = 5
-slowdown_below_layer_time = 15
-temperature = 245
-
-[filament:prusa i3 ABS grün blau]
-bed_temperature = 100
-bridge_fan_speed = 100
-cooling = 1
-disable_fan_first_layers = 1
-extrusion_multiplier = 1
-fan_always_on = 0
-fan_below_layer_time = 60
-filament_colour = #0000A0
-filament_diameter = 2.9
-first_layer_bed_temperature = 100
-first_layer_temperature = 240
-max_fan_speed = 0
-min_fan_speed = 0
-min_print_speed = 10
-slowdown_below_layer_time = 30
+slowdown_below_layer_time = 10
temperature = 235
-[filament:prusa i3 PLA grau]
-bed_temperature = 50
+[filament:2.85mm PETG ]
+bed_temperature = 75
bridge_fan_speed = 100
cooling = 1
-disable_fan_first_layers = 1
+disable_fan_first_layers = 3
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 60
-filament_colour = #808080
-filament_diameter = 2.86
-first_layer_bed_temperature = 50
-first_layer_temperature = 200
+filament_colour = #B1EB96
+filament_diameter = 2.85
+first_layer_bed_temperature = 75
+first_layer_temperature = 245
max_fan_speed = 100
-min_fan_speed = 35
-min_print_speed = 10
+min_fan_speed = 100
+min_print_speed = 5
slowdown_below_layer_time = 10
-temperature = 185
+temperature = 235
-[filament:prusa i3 PLA lila]
-bed_temperature = 50
+[filament:2.85mm PLA]
+bed_temperature = 60
bridge_fan_speed = 100
cooling = 1
-disable_fan_first_layers = 1
+disable_fan_first_layers = 3
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 60
-filament_colour = #8000FF
-filament_diameter = 3
-first_layer_bed_temperature = 50
-first_layer_temperature = 200
+filament_colour = #FF00FF
+filament_diameter = 2.85
+first_layer_bed_temperature = 60
+first_layer_temperature = 220
max_fan_speed = 100
-min_fan_speed = 35
-min_print_speed = 10
-slowdown_below_layer_time = 10
-temperature = 200
+min_fan_speed = 100
+min_print_speed = 5
+slowdown_below_layer_time = 20
+temperature = 195
-[filament:prusa i3 PLA pink]
-bed_temperature = 50
+[filament:2.85mm PLA hot]
+bed_temperature = 60
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #FF00FF
-filament_diameter = 2.83
-first_layer_bed_temperature = 50
-first_layer_temperature = 200
+filament_diameter = 2.85
+first_layer_bed_temperature = 60
+first_layer_temperature = 215
max_fan_speed = 100
-min_fan_speed = 35
-min_print_speed = 10
+min_fan_speed = 100
+min_print_speed = 5
slowdown_below_layer_time = 10
-temperature = 180
+temperature = 215
-[filament:prusa i3 Willowflex]
+[filament:2.85mm Willowflex]
bed_temperature = 70
bridge_fan_speed = 100
cooling = 1
filament_colour = #BF0005
filament_diameter = 2.85
first_layer_bed_temperature = 70
-first_layer_temperature = 200
+first_layer_temperature = 160
max_fan_speed = 100
-min_fan_speed = 35
-min_print_speed = 10
-slowdown_below_layer_time = 10
-temperature = 180
+min_fan_speed = 50
+min_print_speed = 5
+slowdown_below_layer_time = 20
+temperature = 160
[presets]
-filament = prusa i3 Willowflex.ini
-print = MendelPro.ini
-printer = Lulzbot.ini
+filament = 2.80mm PETG .ini
+print = Lulzbot.ini
+printer = MendelPro.ini
[print:Lulzbot]
avoid_crossing_perimeters = 0
bottom_solid_layers = 4
bridge_acceleration = 0
bridge_flow_ratio = 1
-bridge_speed = 40
-brim_width = 0
+bridge_speed = 60
+brim_width = 2
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
-external_perimeter_speed = 20
+external_perimeter_speed = 30
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
-fill_angle = 35
+fill_angle = 45
fill_density = 20%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 0
first_layer_height = 0.2
-first_layer_speed = 10
+first_layer_speed = 20
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
-infill_extrusion_width = 0
+infill_extrusion_width = 1.1
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
-infill_speed = 80
+infill_speed = 60
interface_shells = 0
layer_height = 0.2
-max_print_speed = 100
+max_print_speed = 130
max_volumetric_speed = 0
-min_skirt_length = 0
+min_skirt_length = 1
notes =
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 60
-perimeters = 2
+perimeters = 3
post_process =
raft_layers = 0
resolution = 0
-seam_position = nearest
-skirt_distance = 5
+seam_position = aligned
+skirt_distance = 6
skirt_height = 1
skirts = 1
-small_perimeter_speed = 20
-solid_infill_below_area = 30
+small_perimeter_speed = 15
+solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
-solid_infill_speed = 80
+solid_infill_speed = 10
spiral_vase = 0
standby_temperature_delta = -5
-support_material = 0
+support_material = 1
support_material_angle = 0
-support_material_contact_distance = 0
+support_material_contact_distance = 0.4
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
-support_material_interface_layers = 0
+support_material_interface_layers = 3
support_material_interface_spacing = 0
-support_material_interface_speed = 100%
-support_material_pattern = rectilinear
-support_material_spacing = 2.5
-support_material_speed = 40
-support_material_threshold = 45
-thin_walls = 1
+support_material_interface_speed = 30
+support_material_pattern = rectilinear-grid
+support_material_spacing = 2
+support_material_speed = 60
+support_material_threshold = 0
+thin_walls = 0
threads = 2
top_infill_extrusion_width = 0
-top_solid_infill_speed = 20
-top_solid_layers = 4
-travel_speed = 100
+top_solid_infill_speed = 5
+top_solid_layers = 5
+travel_speed = 130
xy_size_compensation = 0
[print:MendelPro]
-avoid_crossing_perimeters = 0
-bottom_solid_layers = 4
+avoid_crossing_perimeters = 1
+bottom_solid_layers = 5
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 40
-brim_width = 1
+brim_width = 2
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
-external_perimeter_speed = 20
+external_perimeter_speed = 30
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
first_layer_acceleration = 0
first_layer_extrusion_width = 0
first_layer_height = 0.2
-first_layer_speed = 10
-gap_fill_speed = 10
+first_layer_speed = 30
+gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
-infill_overlap = 15%
-infill_speed = 0
+infill_overlap = 25%
+infill_speed = 50
interface_shells = 0
layer_height = 0.2
max_print_speed = 80
max_volumetric_speed = 0
-min_skirt_length = 2
+min_skirt_length = 6
notes =
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
-perimeter_speed = 0
-perimeters = 2
+perimeter_speed = 50
+perimeters = 3
post_process =
raft_layers = 0
resolution = 0
seam_position = nearest
-skirt_distance = 10
+skirt_distance = 6
skirt_height = 1
skirts = 1
-small_perimeter_speed = 10
+small_perimeter_speed = 20
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
-solid_infill_speed = 0
+solid_infill_speed = 40
spiral_vase = 0
standby_temperature_delta = -5
support_material = 1
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
-support_material_interface_speed = 100%
-support_material_pattern = pillars
+support_material_interface_speed = 40
+support_material_pattern = rectilinear
support_material_spacing = 3
-support_material_speed = 60
+support_material_speed = 50
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
-top_solid_infill_speed = 20
-top_solid_layers = 4
+top_solid_infill_speed = 40
+top_solid_layers = 5
travel_speed = 100
xy_size_compensation = 0
travel_speed = 100
xy_size_compensation = 0
-[print:prusa i3 200]
-avoid_crossing_perimeters = 1
+[print:prusa i3]
+avoid_crossing_perimeters = 0
bottom_solid_layers = 4
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 40
-brim_width = 1
+brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
-external_perimeter_speed = 20
+external_perimeter_speed = 30
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extrusion_width = 0
fill_angle = 45
fill_density = 20%
-fill_pattern = rectilinear
+fill_pattern = honeycomb
first_layer_acceleration = 0
first_layer_extrusion_width = 0
-first_layer_height = 0.2
-first_layer_speed = 15
+first_layer_height = 0.3
+first_layer_speed = 10
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
-infill_speed = 0
+infill_speed = 80
interface_shells = 0
-layer_height = 0.2
-max_print_speed = 50
+layer_height = 0.15
+max_print_speed = 100
max_volumetric_speed = 0
min_skirt_length = 3
notes =
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
-perimeter_speed = 40
+perimeter_speed = 60
perimeters = 3
post_process =
raft_layers = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
-solid_infill_speed = 0
+solid_infill_speed = 40
spiral_vase = 0
standby_temperature_delta = -5
-support_material = 0
+support_material = 1
support_material_angle = 0
-support_material_contact_distance = 0.2
+support_material_contact_distance = 0.3
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
-support_material_interface_speed = 10
-support_material_pattern = pillars
-support_material_spacing = 2.5
+support_material_interface_speed = 40
+support_material_pattern = rectilinear
+support_material_spacing = 3
support_material_speed = 40
-support_material_threshold = 40
+support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
-top_solid_infill_speed = 20
+top_solid_infill_speed = 30
top_solid_layers = 4
travel_speed = 100
xy_size_compensation = 0
-[print:prusa i3 vase]
+[print:prusa i3 test]
avoid_crossing_perimeters = 0
-bottom_solid_layers = 0
+bottom_solid_layers = 4
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 40
-brim_width = 1
+brim_width = 5
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
-external_perimeter_speed = 20
+external_perimeter_speed = 30
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
-fill_density = 0%
-fill_pattern = rectilinear
+fill_density = 20%
+fill_pattern = honeycomb
first_layer_acceleration = 0
first_layer_extrusion_width = 0
first_layer_height = 0.2
-first_layer_speed = 15
+first_layer_speed = 10
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
-infill_first = 1
+infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
-infill_speed = 60
+infill_speed = 80
interface_shells = 0
layer_height = 0.2
-max_print_speed = 65
+max_print_speed = 100
max_volumetric_speed = 0
-min_skirt_length = 1
+min_skirt_length = 3
notes =
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
-perimeter_speed = 40
-perimeters = 1
+perimeter_speed = 60
+perimeters = 3
post_process =
raft_layers = 0
resolution = 0
seam_position = nearest
-skirt_distance = 1
+skirt_distance = 6
skirt_height = 1
skirts = 1
-small_perimeter_speed = 20
+small_perimeter_speed = 15
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
-solid_infill_speed = 60
-spiral_vase = 1
+solid_infill_speed = 40
+spiral_vase = 0
standby_temperature_delta = -5
-support_material = 0
+support_material = 1
support_material_angle = 0
-support_material_contact_distance = 0.2
+support_material_contact_distance = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
-support_material_interface_speed = 10
+support_material_interface_speed = 40
support_material_pattern = pillars
-support_material_spacing = 2.5
+support_material_spacing = 3
support_material_speed = 40
-support_material_threshold = 40
+support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
-top_solid_infill_speed = 20
-top_solid_layers = 0
+top_solid_infill_speed = 30
+top_solid_layers = 4
travel_speed = 100
xy_size_compensation = 0
[printer:Lulzbot]
bed_shape = 0x0,298x0,298x275,0x275
before_layer_gcode =
-end_gcode = M104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200 ;\nG28 X0 ; home X axis\nM84 ; disable motors\n\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\n
+end_gcode = M104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200 ;\nG28 X0 ; home X axis\nM84 ; disable motors\n\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\n
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode =
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
-start_gcode = G28 Z ; home Z\nG28 X Y ; home X Y\n
+start_gcode = G28 Z ; home Z\nG28 X Y ; home X Y\nG0 Y40 ; clab move\n
toolchange_gcode =
use_firmware_retraction = 0
use_relative_e_distances = 0
pressure_advance = 0
retract_before_travel = 2
retract_layer_change = 0
-retract_length = 3
+retract_length = 2
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
-start_gcode = G28 Z ; home Z\n;G0 Z1 ; lift Z\nG28 X Y ; home X Y\nG0 Y40 ; clab move
+start_gcode = G28 Z ; home Z\n;G0 Z1 ; lift Z\nG28 X Y ; home X Y\nG0 Y40 ; clab move
toolchange_gcode = M83 ; turn on relative movement for extruder \nG1 E-5 ; retract filament 5mm \nG1 X10 Y10 Z4.000000 ; home X and Y axis leave Z at current height \nM84 E ; release extruder stepper motor from 'holding' position \n@pause ; pause print! \nG1 E0 ; reset extruder, ready to push out plastic again \nM82 ; set extruder movement back to absolute ready for next layer
-use_firmware_retraction = 1
+use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
projects / stratum0-wiki.git / blobdiff