-# generated by Slic3r 1.2.9 on Sun Aug 14 14:31:08 2016
+# generated by Slic3r Prusa Edition 1.38.5-prusa3d-win64 on 2018-01-16 at 20:47:39
-[filament:LulzBot ABS]
-bed_temperature = 100
-bridge_fan_speed = 50
-cooling = 1
-disable_fan_first_layers = 1
-extrusion_multiplier = 1
-fan_always_on = 0
-fan_below_layer_time = 60
-filament_colour = #FFFFFF
-filament_diameter = 2.85
-first_layer_bed_temperature = 100
-first_layer_temperature = 250
-max_fan_speed = 0
-min_fan_speed = 0
-min_print_speed = 5
-slowdown_below_layer_time = 20
-temperature = 230
-
-[filament:LulzBot PLA]
-bed_temperature = 50
-bridge_fan_speed = 100
-cooling = 1
-disable_fan_first_layers = 1
-extrusion_multiplier = 1
-fan_always_on = 1
-fan_below_layer_time = 60
-filament_colour = #FFFFFF
-filament_diameter = 2.82
-first_layer_bed_temperature = 50
-first_layer_temperature = 200
-max_fan_speed = 100
-min_fan_speed = 35
-min_print_speed = 5
-slowdown_below_layer_time = 30
-temperature = 200
-
-[filament:LulzBot PLA DAS FILAMENT]
-bed_temperature = 50
-bridge_fan_speed = 100
-cooling = 1
-disable_fan_first_layers = 1
-extrusion_multiplier = 1
-fan_always_on = 0
-fan_below_layer_time = 60
-filament_colour = #FFFFFF
-filament_diameter = 2.85
-first_layer_bed_temperature = 50
-first_layer_temperature = 220
-max_fan_speed = 100
-min_fan_speed = 30
-min_print_speed = 5
-slowdown_below_layer_time = 30
-temperature = 215
-
-[filament:MendelPro ABS]
-bed_temperature = 0
-bridge_fan_speed = 100
-cooling = 0
-disable_fan_first_layers = 1
-extrusion_multiplier = 1
-fan_always_on = 0
-fan_below_layer_time = 60
-filament_colour = #FFFFFF
-filament_diameter = 1.7
-first_layer_bed_temperature = 0
-first_layer_temperature = 250
-max_fan_speed = 100
-min_fan_speed = 50
-min_print_speed = 5
-slowdown_below_layer_time = 30
-temperature = 245
-
-[filament:MendelPro Holz]
-bed_temperature = 50
-bridge_fan_speed = 100
-cooling = 1
-disable_fan_first_layers = 1
-extrusion_multiplier = 1
-fan_always_on = 1
-fan_below_layer_time = 60
-filament_colour = #FFFFFF
-filament_diameter = 1.7
-first_layer_bed_temperature = 55
-first_layer_temperature = 200
-max_fan_speed = 100
-min_fan_speed = 50
-min_print_speed = 5
-slowdown_below_layer_time = 30
-temperature = 185
-
-[filament:MendelPro Mystery]
-bed_temperature = 80
-bridge_fan_speed = 50
-cooling = 1
-disable_fan_first_layers = 1
-extrusion_multiplier = 1
-fan_always_on = 0
-fan_below_layer_time = 60
-filament_colour = #FFFFFF
-filament_diameter = 1.7
-first_layer_bed_temperature = 80
-first_layer_temperature = 250
-max_fan_speed = 0
-min_fan_speed = 0
-min_print_speed = 10
-slowdown_below_layer_time = 20
-temperature = 200
-
-[filament:MendelPro PLA]
-bed_temperature = 50
-bridge_fan_speed = 100
-cooling = 1
-disable_fan_first_layers = 1
-extrusion_multiplier = 1
-fan_always_on = 1
-fan_below_layer_time = 60
-filament_colour = #FFFFFF
-filament_diameter = 1.7
-first_layer_bed_temperature = 55
-first_layer_temperature = 200
-max_fan_speed = 100
-min_fan_speed = 40
-min_print_speed = 5
-slowdown_below_layer_time = 30
-temperature = 185
-
-[filament:MendelPro PLA fast]
-bed_temperature = 50
-bridge_fan_speed = 100
-cooling = 1
-disable_fan_first_layers = 1
-extrusion_multiplier = 1
-fan_always_on = 1
-fan_below_layer_time = 60
-filament_colour = #FFFFFF
-filament_diameter = 1.7
-first_layer_bed_temperature = 50
-first_layer_temperature = 200
-max_fan_speed = 100
-min_fan_speed = 50
-min_print_speed = 5
-slowdown_below_layer_time = 30
-temperature = 200
-
-[filament:MendelPro PLA transparent]
-bed_temperature = 50
-bridge_fan_speed = 100
-cooling = 1
-disable_fan_first_layers = 1
-extrusion_multiplier = 1
-fan_always_on = 1
-fan_below_layer_time = 60
-filament_colour = #FFFFFF
-filament_diameter = 1.7
-first_layer_bed_temperature = 55
-first_layer_temperature = 200
-max_fan_speed = 100
-min_fan_speed = 40
-min_print_speed = 5
-slowdown_below_layer_time = 30
-temperature = 200
-
-[filament:TinyBoy PLA]
-bed_temperature = 0
-bridge_fan_speed = 100
-cooling = 1
-disable_fan_first_layers = 2
-extrusion_multiplier = 0.9
-fan_always_on = 1
-fan_below_layer_time = 60
-filament_colour = #35E1FF
-filament_diameter = 1.63
-first_layer_bed_temperature = 0
-first_layer_temperature = 200
-max_fan_speed = 40
-min_fan_speed = 35
-min_print_speed = 5
-slowdown_below_layer_time = 15
-temperature = 190
-
-[filament:Prusa i3 ABS grün]
-bed_temperature = 100
-bridge_fan_speed = 70
-cooling = 1
-disable_fan_first_layers = 1
-extrusion_multiplier = 1
-fan_always_on = 0
-fan_below_layer_time = 60
-filament_colour = #80FF00
-filament_diameter = 2.9
-first_layer_bed_temperature = 100
-first_layer_temperature = 255
-max_fan_speed = 0
-min_fan_speed = 0
-min_print_speed = 5
-slowdown_below_layer_time = 15
-temperature = 245
-
-[filament:Prusa i3 ABS grün blau]
-bed_temperature = 100
-bridge_fan_speed = 70
-cooling = 1
-disable_fan_first_layers = 1
-extrusion_multiplier = 1
-fan_always_on = 0
-fan_below_layer_time = 60
-filament_colour = #0000A0
-filament_diameter = 2.9
-first_layer_bed_temperature = 100
-first_layer_temperature = 240
-max_fan_speed = 0
-min_fan_speed = 0
-min_print_speed = 5
-slowdown_below_layer_time = 30
-temperature = 235
-
-[filament:Prusa i3 ABS schwarz]
-bed_temperature = 100
-bridge_fan_speed = 70
-cooling = 1
-disable_fan_first_layers = 1
-extrusion_multiplier = 1
-fan_always_on = 0
-fan_below_layer_time = 60
-filament_colour = #000000
-filament_diameter = 2.9
-first_layer_bed_temperature = 100
-first_layer_temperature = 260
-max_fan_speed = 0
-min_fan_speed = 0
-min_print_speed = 5
-slowdown_below_layer_time = 15
-temperature = 255
-
-[filament:Prusa i3 PLA]
-bed_temperature = 50
-bridge_fan_speed = 100
-cooling = 1
-disable_fan_first_layers = 1
-extrusion_multiplier = 1
-fan_always_on = 1
-fan_below_layer_time = 60
-filament_colour = #FFFFFF
-filament_diameter = 2.9
-first_layer_bed_temperature = 50
-first_layer_temperature = 200
-max_fan_speed = 100
-min_fan_speed = 50
-min_print_speed = 5
-slowdown_below_layer_time = 30
-temperature = 190
-
-[filament:Prusa i3 PLA lila]
-bed_temperature = 50
-bridge_fan_speed = 100
-cooling = 1
-disable_fan_first_layers = 1
-extrusion_multiplier = 1
-fan_always_on = 1
-fan_below_layer_time = 60
-filament_colour = #8000FF
-filament_diameter = 3
-first_layer_bed_temperature = 50
-first_layer_temperature = 200
-max_fan_speed = 100
-min_fan_speed = 35
-min_print_speed = 5
-slowdown_below_layer_time = 15
-temperature = 200
-
-[filament:Prusa i3 PLA pink]
-bed_temperature = 50
-bridge_fan_speed = 100
-cooling = 1
-disable_fan_first_layers = 1
-extrusion_multiplier = 1
-fan_always_on = 1
-fan_below_layer_time = 60
-filament_colour = #FF00FF
-filament_diameter = 2.83
-first_layer_bed_temperature = 50
-first_layer_temperature = 200
-max_fan_speed = 100
-min_fan_speed = 35
-min_print_speed = 5
-slowdown_below_layer_time = 15
-temperature = 180
-
-[print:LulzBot fine]
-avoid_crossing_perimeters = 1
-bottom_solid_layers = 2
-bridge_acceleration = 0
-bridge_flow_ratio = 1
-bridge_speed = 40
-brim_width = 5
-complete_objects = 0
-default_acceleration = 0
-dont_support_bridges = 1
-external_fill_pattern = rectilinear
-external_perimeter_extrusion_width = 0
-external_perimeter_speed = 50%
-external_perimeters_first = 0
-extra_perimeters = 1
-extruder_clearance_height = 20
-extruder_clearance_radius = 20
-extrusion_width = 0
-fill_angle = 35
-fill_density = 15%
-fill_pattern = 3dhoneycomb
-first_layer_acceleration = 0
-first_layer_extrusion_width = 0
-first_layer_height = 0.2
-first_layer_speed = 10
-gap_fill_speed = 20
-gcode_comments = 0
-infill_acceleration = 0
-infill_every_layers = 1
-infill_extruder = 1
-infill_extrusion_width = 0
-infill_first = 0
-infill_only_where_needed = 0
-infill_overlap = 15%
-infill_speed = 80
-interface_shells = 0
-layer_height = 0.2
-max_print_speed = 80
-max_volumetric_speed = 0
-min_skirt_length = 2
-notes =
-only_retract_when_crossing_perimeters = 0
-ooze_prevention = 0
-output_filename_format = [input_filename_base].gcode
-overhangs = 1
-perimeter_acceleration = 0
-perimeter_extruder = 1
-perimeter_extrusion_width = 0
-perimeter_speed = 60
-perimeters = 3
-post_process =
-raft_layers = 0
-resolution = 0
-seam_position = aligned
-skirt_distance = 10
-skirt_height = 1
-skirts = 2
-small_perimeter_speed = 20
-solid_infill_below_area = 30
-solid_infill_every_layers = 0
-solid_infill_extruder = 1
-solid_infill_extrusion_width = 0
-solid_infill_speed = 20
-spiral_vase = 0
-standby_temperature_delta = -5
-support_material = 0
-support_material_angle = 0
-support_material_contact_distance = 0.2
-support_material_enforce_layers = 0
-support_material_extruder = 1
-support_material_extrusion_width = 0
-support_material_interface_extruder = 1
-support_material_interface_layers = 0
-support_material_interface_spacing = 0
-support_material_interface_speed = 100%
-support_material_pattern = rectilinear
-support_material_spacing = 2.5
-support_material_speed = 60
-support_material_threshold = 45
-thin_walls = 1
-threads = 2
-top_infill_extrusion_width = 0
-top_solid_infill_speed = 20
-top_solid_layers = 3
-travel_speed = 100
-xy_size_compensation = 0
-
-[print:LulzBot fine support]
-avoid_crossing_perimeters = 1
-bottom_solid_layers = 2
-bridge_acceleration = 0
-bridge_flow_ratio = 1
-bridge_speed = 40
-brim_width = 3
-complete_objects = 0
-default_acceleration = 0
-dont_support_bridges = 1
-external_fill_pattern = rectilinear
-external_perimeter_extrusion_width = 0
-external_perimeter_speed = 50%
-external_perimeters_first = 0
-extra_perimeters = 1
-extruder_clearance_height = 20
-extruder_clearance_radius = 20
-extrusion_width = 0
-fill_angle = 35
-fill_density = 15%
-fill_pattern = 3dhoneycomb
-first_layer_acceleration = 0
-first_layer_extrusion_width = 0
-first_layer_height = 0.2
-first_layer_speed = 10
-gap_fill_speed = 20
-gcode_comments = 0
-infill_acceleration = 0
-infill_every_layers = 1
-infill_extruder = 1
-infill_extrusion_width = 0
-infill_first = 0
-infill_only_where_needed = 0
-infill_overlap = 15%
-infill_speed = 80
-interface_shells = 0
-layer_height = 0.2
-max_print_speed = 80
-max_volumetric_speed = 0
-min_skirt_length = 2
-notes =
-only_retract_when_crossing_perimeters = 0
-ooze_prevention = 0
-output_filename_format = [input_filename_base].gcode
-overhangs = 1
-perimeter_acceleration = 0
-perimeter_extruder = 1
-perimeter_extrusion_width = 0
-perimeter_speed = 60
-perimeters = 3
-post_process =
-raft_layers = 0
-resolution = 0
-seam_position = aligned
-skirt_distance = 10
-skirt_height = 1
-skirts = 2
-small_perimeter_speed = 20
-solid_infill_below_area = 30
-solid_infill_every_layers = 0
-solid_infill_extruder = 1
-solid_infill_extrusion_width = 0
-solid_infill_speed = 20
-spiral_vase = 0
-standby_temperature_delta = -5
-support_material = 1
-support_material_angle = 0
-support_material_contact_distance = 0.2
-support_material_enforce_layers = 0
-support_material_extruder = 1
-support_material_extrusion_width = 0
-support_material_interface_extruder = 1
-support_material_interface_layers = 3
-support_material_interface_spacing = 0
-support_material_interface_speed = 100%
-support_material_pattern = honeycomb
-support_material_spacing = 2.5
-support_material_speed = 60
-support_material_threshold = 45
-thin_walls = 1
-threads = 2
-top_infill_extrusion_width = 0
-top_solid_infill_speed = 20
-top_solid_layers = 3
-travel_speed = 100
-xy_size_compensation = 0
-
-[print:MendelPro]
-avoid_crossing_perimeters = 0
-bottom_solid_layers = 3
-bridge_acceleration = 0
-bridge_flow_ratio = 1
-bridge_speed = 40
-brim_width = 1
-complete_objects = 0
-default_acceleration = 0
-dont_support_bridges = 1
-external_fill_pattern = rectilinear
-external_perimeter_extrusion_width = 0
-external_perimeter_speed = 20
-external_perimeters_first = 0
-extra_perimeters = 1
-extruder_clearance_height = 20
-extruder_clearance_radius = 20
-extrusion_width = 0
-fill_angle = 45
-fill_density = 15%
-fill_pattern = 3dhoneycomb
-first_layer_acceleration = 0
-first_layer_extrusion_width = 0
-first_layer_height = 0.2
-first_layer_speed = 10
-gap_fill_speed = 10
-gcode_comments = 0
-infill_acceleration = 0
-infill_every_layers = 1
-infill_extruder = 1
-infill_extrusion_width = 0
-infill_first = 0
-infill_only_where_needed = 0
-infill_overlap = 15%
-infill_speed = 0
-interface_shells = 0
-layer_height = 0.2
-max_print_speed = 80
-max_volumetric_speed = 0
-min_skirt_length = 2
-notes =
-only_retract_when_crossing_perimeters = 1
-ooze_prevention = 0
-output_filename_format = [input_filename_base].gcode
-overhangs = 1
-perimeter_acceleration = 0
-perimeter_extruder = 1
-perimeter_extrusion_width = 0
-perimeter_speed = 0
-perimeters = 2
-post_process =
-raft_layers = 0
-resolution = 0
-seam_position = aligned
-skirt_distance = 1
-skirt_height = 1
-skirts = 2
-small_perimeter_speed = 10
-solid_infill_below_area = 70
-solid_infill_every_layers = 0
-solid_infill_extruder = 1
-solid_infill_extrusion_width = 0
-solid_infill_speed = 0
-spiral_vase = 0
-standby_temperature_delta = -5
-support_material = 0
-support_material_angle = 0
-support_material_contact_distance = 0.2
-support_material_enforce_layers = 0
-support_material_extruder = 1
-support_material_extrusion_width = 0
-support_material_interface_extruder = 1
-support_material_interface_layers = 2
-support_material_interface_spacing = 0
-support_material_interface_speed = 100%
-support_material_pattern = rectilinear
-support_material_spacing = 5
-support_material_speed = 60
-support_material_threshold = 40
-thin_walls = 1
-threads = 2
-top_infill_extrusion_width = 0
-top_solid_infill_speed = 20
-top_solid_layers = 3
-travel_speed = 100
-xy_size_compensation = 0
-
-[print:MendelPro fast]
-avoid_crossing_perimeters = 0
-bottom_solid_layers = 3
-bridge_acceleration = 0
-bridge_flow_ratio = 1
-bridge_speed = 40
-brim_width = 0
-complete_objects = 0
-default_acceleration = 0
-dont_support_bridges = 1
-external_fill_pattern = rectilinear
-external_perimeter_extrusion_width = 0
-external_perimeter_speed = 20
-external_perimeters_first = 0
-extra_perimeters = 1
-extruder_clearance_height = 20
-extruder_clearance_radius = 20
-extrusion_width = 0
-fill_angle = 45
-fill_density = 15%
-fill_pattern = 3dhoneycomb
-first_layer_acceleration = 0
-first_layer_extrusion_width = 0
-first_layer_height = 0.2
-first_layer_speed = 10
-gap_fill_speed = 10
-gcode_comments = 0
-infill_acceleration = 0
-infill_every_layers = 1
-infill_extruder = 1
-infill_extrusion_width = 0
-infill_first = 0
-infill_only_where_needed = 0
-infill_overlap = 15%
-infill_speed = 0
-interface_shells = 0
-layer_height = 0.5
-max_print_speed = 80
-max_volumetric_speed = 0
-min_skirt_length = 2
-notes =
-only_retract_when_crossing_perimeters = 1
-ooze_prevention = 0
-output_filename_format = [input_filename_base].gcode
-overhangs = 1
-perimeter_acceleration = 0
-perimeter_extruder = 1
-perimeter_extrusion_width = 0
-perimeter_speed = 0
-perimeters = 2
-post_process =
-raft_layers = 0
-resolution = 0
-seam_position = aligned
-skirt_distance = 1
-skirt_height = 1
-skirts = 2
-small_perimeter_speed = 10
-solid_infill_below_area = 70
-solid_infill_every_layers = 0
-solid_infill_extruder = 1
-solid_infill_extrusion_width = 0
-solid_infill_speed = 0
-spiral_vase = 0
-standby_temperature_delta = -5
-support_material = 0
-support_material_angle = 0
-support_material_contact_distance = 0.2
-support_material_enforce_layers = 0
-support_material_extruder = 1
-support_material_extrusion_width = 0
-support_material_interface_extruder = 1
-support_material_interface_layers = 2
-support_material_interface_spacing = 0
-support_material_interface_speed = 100%
-support_material_pattern = rectilinear
-support_material_spacing = 5
-support_material_speed = 60
-support_material_threshold = 40
-thin_walls = 1
-threads = 2
-top_infill_extrusion_width = 0
-top_solid_infill_speed = 20
-top_solid_layers = 3
-travel_speed = 100
-xy_size_compensation = 0
-
-[print:MendelPro support]
-avoid_crossing_perimeters = 0
-bottom_solid_layers = 3
-bridge_acceleration = 0
-bridge_flow_ratio = 1
-bridge_speed = 40
-brim_width = 3
-complete_objects = 0
-default_acceleration = 0
-dont_support_bridges = 1
-external_fill_pattern = rectilinear
-external_perimeter_extrusion_width = 0
-external_perimeter_speed = 20
-external_perimeters_first = 0
-extra_perimeters = 1
-extruder_clearance_height = 20
-extruder_clearance_radius = 20
-extrusion_width = 0
-fill_angle = 45
-fill_density = 15%
-fill_pattern = 3dhoneycomb
-first_layer_acceleration = 0
-first_layer_extrusion_width = 0
-first_layer_height = 0.2
-first_layer_speed = 10
-gap_fill_speed = 10
-gcode_comments = 0
-infill_acceleration = 0
-infill_every_layers = 1
-infill_extruder = 1
-infill_extrusion_width = 0
-infill_first = 0
-infill_only_where_needed = 0
-infill_overlap = 15%
-infill_speed = 0
-interface_shells = 0
-layer_height = 0.2
-max_print_speed = 80
-max_volumetric_speed = 0
-min_skirt_length = 2
-notes =
-only_retract_when_crossing_perimeters = 1
-ooze_prevention = 0
-output_filename_format = [input_filename_base].gcode
-overhangs = 1
-perimeter_acceleration = 0
-perimeter_extruder = 1
-perimeter_extrusion_width = 0
-perimeter_speed = 0
-perimeters = 2
-post_process =
-raft_layers = 0
-resolution = 0
-seam_position = aligned
-skirt_distance = 1
-skirt_height = 1
-skirts = 2
-small_perimeter_speed = 10
-solid_infill_below_area = 70
-solid_infill_every_layers = 0
-solid_infill_extruder = 1
-solid_infill_extrusion_width = 0
-solid_infill_speed = 0
-spiral_vase = 0
-standby_temperature_delta = -5
-support_material = 1
-support_material_angle = 0
-support_material_contact_distance = 0.2
-support_material_enforce_layers = 0
-support_material_extruder = 1
-support_material_extrusion_width = 0
-support_material_interface_extruder = 1
-support_material_interface_layers = 3
-support_material_interface_spacing = 0
-support_material_interface_speed = 100%
-support_material_pattern = honeycomb
-support_material_spacing = 2.5
-support_material_speed = 60
-support_material_threshold = 40
-thin_walls = 1
-threads = 2
-top_infill_extrusion_width = 0
-top_solid_infill_speed = 20
-top_solid_layers = 3
-travel_speed = 100
-xy_size_compensation = 0
-
-[print:TinyBoy]
-avoid_crossing_perimeters = 0
+[print:Kossel print]
+avoid_crossing_perimeters = 1
bottom_solid_layers = 3
bridge_acceleration = 0
+bridge_angle = 0
bridge_flow_ratio = 1
-bridge_speed = 40
+bridge_speed = 60
brim_width = 0
+clip_multipart_objects = 0
+compatible_printers =
+compatible_printers_condition =
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
+elefant_foot_compensation = 0
+ensure_vertical_shell_thickness = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
-external_perimeter_speed = 20
+external_perimeter_speed = 30
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extrusion_width = 0
fill_angle = 45
fill_density = 20%
-fill_pattern = 3dhoneycomb
+fill_pattern = cubic
first_layer_acceleration = 0
-first_layer_extrusion_width = 0
+first_layer_extrusion_width = 200%
first_layer_height = 0.2
-first_layer_speed = 10
+first_layer_speed = 30
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
-infill_overlap = 15%
-infill_speed = 0
+infill_overlap = 25%
+infill_speed = 80
interface_shells = 0
layer_height = 0.2
max_print_speed = 80
+max_volumetric_extrusion_rate_slope_negative = 0
+max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
-min_skirt_length = 1
+min_skirt_length = 0
notes =
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
-perimeter_speed = 0
-perimeters = 2
+perimeter_speed = 60
+perimeters = 3
post_process =
raft_layers = 0
resolution = 0
seam_position = aligned
-skirt_distance = 1
+skirt_distance = 6
skirt_height = 1
-skirts = 1
-small_perimeter_speed = 0
+skirts = 3
+small_perimeter_speed = 15
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
-solid_infill_speed = 0
+solid_infill_speed = 20
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
-support_material_contact_distance = 0.2
+support_material_buildplate_only = 0
+support_material_contact_distance = 0.4
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
+support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
-support_material_interface_layers = 2
+support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
-support_material_pattern = rectilinear
-support_material_spacing = 5
-support_material_speed = 0
+support_material_pattern = pillars
+support_material_spacing = 2.5
+support_material_speed = 60
+support_material_synchronize_layers = 0
support_material_threshold = 40
+support_material_with_sheath = 1
+support_material_xy_spacing = 0.6
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
-top_solid_infill_speed = 20
-top_solid_layers = 4
-travel_speed = 100
+top_solid_infill_speed = 15
+top_solid_layers = 3
+travel_speed = 130
+wipe_tower = 1
+wipe_tower_per_color_wipe = 10
+wipe_tower_width = 10
+wipe_tower_x = 0
+wipe_tower_y = 65
xy_size_compensation = 0
-[print:TinyBoy support]
-avoid_crossing_perimeters = 0
+[print:Lulzbot print]
+avoid_crossing_perimeters = 1
bottom_solid_layers = 3
-bridge_acceleration = 0
+bridge_acceleration = 2000
+bridge_angle = 0
bridge_flow_ratio = 1
-bridge_speed = 40
+bridge_speed = 72
brim_width = 0
+clip_multipart_objects = 0
+compatible_printers =
+compatible_printers_condition =
complete_objects = 0
-default_acceleration = 0
+default_acceleration = 2000
dont_support_bridges = 1
+elefant_foot_compensation = 0
+ensure_vertical_shell_thickness = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
-external_perimeter_speed = 20
+external_perimeter_speed = 45
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
-extrusion_width = 0
+extrusion_width = 0.42
fill_angle = 45
fill_density = 20%
-fill_pattern = 3dhoneycomb
-first_layer_acceleration = 0
-first_layer_extrusion_width = 0
-first_layer_height = 0.2
+fill_pattern = cubic
+first_layer_acceleration = 2000
+first_layer_extrusion_width = 0.53
+first_layer_height = 100%
first_layer_speed = 10
-gap_fill_speed = 20
+gap_fill_speed = 55
gcode_comments = 0
-infill_acceleration = 0
+infill_acceleration = 2000
infill_every_layers = 1
infill_extruder = 1
-infill_extrusion_width = 0
+infill_extrusion_width = 0.68
infill_first = 0
infill_only_where_needed = 0
-infill_overlap = 15%
-infill_speed = 0
+infill_overlap = 55%
+infill_speed = 80
interface_shells = 0
layer_height = 0.2
max_print_speed = 80
+max_volumetric_extrusion_rate_slope_negative = 0
+max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
-min_skirt_length = 1
-notes =
-only_retract_when_crossing_perimeters = 1
-ooze_prevention = 0
-output_filename_format = [input_filename_base].gcode
-overhangs = 1
-perimeter_acceleration = 0
-perimeter_extruder = 1
-perimeter_extrusion_width = 0
-perimeter_speed = 0
-perimeters = 2
-post_process =
-raft_layers = 0
-resolution = 0
-seam_position = aligned
-skirt_distance = 1
-skirt_height = 1
-skirts = 1
-small_perimeter_speed = 0
-solid_infill_below_area = 70
-solid_infill_every_layers = 0
-solid_infill_extruder = 1
-solid_infill_extrusion_width = 0
-solid_infill_speed = 0
-spiral_vase = 0
-standby_temperature_delta = -5
-support_material = 1
-support_material_angle = 0
-support_material_contact_distance = 0.3
-support_material_enforce_layers = 0
-support_material_extruder = 1
-support_material_extrusion_width = 0
-support_material_interface_extruder = 1
-support_material_interface_layers = 2
-support_material_interface_spacing = 0
-support_material_interface_speed = 100%
-support_material_pattern = rectilinear
-support_material_spacing = 5
-support_material_speed = 0
-support_material_threshold = 40
-thin_walls = 1
-threads = 2
-top_infill_extrusion_width = 0
-top_solid_infill_speed = 20
-top_solid_layers = 4
-travel_speed = 100
-xy_size_compensation = 0
-
-[print:ToyRep]
-avoid_crossing_perimeters = 0
-bottom_solid_layers = 2
-bridge_acceleration = 0
-bridge_flow_ratio = 1
-bridge_speed = 0
-brim_width = 0
-complete_objects = 0
-default_acceleration = 0
-dont_support_bridges = 1
-external_fill_pattern = rectilinear
-external_perimeter_extrusion_width = 0
-external_perimeter_speed = 0
-external_perimeters_first = 0
-extra_perimeters = 1
-extruder_clearance_height = 20
-extruder_clearance_radius = 20
-extrusion_width = 0
-fill_angle = 45
-fill_density = 0%
-fill_pattern = rectilinear
-first_layer_acceleration = 0
-first_layer_extrusion_width = 0
-first_layer_height = 0.2
-first_layer_speed = 10
-gap_fill_speed = 0
-gcode_comments = 0
-infill_acceleration = 0
-infill_every_layers = 1
-infill_extruder = 1
-infill_extrusion_width = 0
-infill_first = 0
-infill_only_where_needed = 0
-infill_overlap = 15%
-infill_speed = 0
-interface_shells = 0
-layer_height = 0.2
-max_print_speed = 10
-max_volumetric_speed = 0
-min_skirt_length = 1
+min_skirt_length = 0
notes =
-only_retract_when_crossing_perimeters = 1
+only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
-perimeter_acceleration = 0
+perimeter_acceleration = 1200
perimeter_extruder = 1
-perimeter_extrusion_width = 0
-perimeter_speed = 0
-perimeters = 2
+perimeter_extrusion_width = 0.38
+perimeter_speed = 75
+perimeters = 3
post_process =
+print_settings_id =
raft_layers = 0
resolution = 0
seam_position = aligned
-skirt_distance = 1
+skirt_distance = 5
skirt_height = 1
-skirts = 1
-small_perimeter_speed = 0
-solid_infill_below_area = 70
+skirts = 3
+small_perimeter_speed = 50
+solid_infill_below_area = 90
solid_infill_every_layers = 0
solid_infill_extruder = 1
-solid_infill_extrusion_width = 0
-solid_infill_speed = 0
+solid_infill_extrusion_width = 0.5
+solid_infill_speed = 75
spiral_vase = 0
standby_temperature_delta = -5
-support_material = 1
+support_material = 0
support_material_angle = 0
+support_material_buildplate_only = 0
support_material_contact_distance = 0.3
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
+support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
-support_material_interface_layers = 3
+support_material_interface_layers = 5
support_material_interface_spacing = 0
support_material_interface_speed = 100%
-support_material_pattern = rectilinear
-support_material_spacing = 5
-support_material_speed = 0
-support_material_threshold = 40
+support_material_pattern = rectilinear-grid
+support_material_spacing = 7
+support_material_speed = 60
+support_material_synchronize_layers = 0
+support_material_threshold = 30
+support_material_with_sheath = 0
+support_material_xy_spacing = 0.5
thin_walls = 1
threads = 2
-top_infill_extrusion_width = 0
-top_solid_infill_speed = 0
-top_solid_layers = 0
-travel_speed = 100
+top_infill_extrusion_width = 0.4
+top_solid_infill_speed = 60
+top_solid_layers = 3
+travel_speed = 160
+wipe_tower = 0
+wipe_tower_per_color_wipe = 15
+wipe_tower_width = 60
+wipe_tower_x = 180
+wipe_tower_y = 140
xy_size_compensation = 0
-[print:Prusa i3 200]
+[print:Mendel print]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 0
+bridge_angle = 0
bridge_flow_ratio = 1
bridge_speed = 40
-brim_width = 5
+brim_width = 2
+clip_multipart_objects = 0
+compatible_printers =
+compatible_printers_condition =
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
+elefant_foot_compensation = 0
+ensure_vertical_shell_thickness = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
-external_perimeter_speed = 20
+external_perimeter_speed = 30
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extrusion_width = 0
fill_angle = 45
fill_density = 20%
-fill_pattern = 3dhoneycomb
+fill_pattern = cubic
first_layer_acceleration = 0
-first_layer_extrusion_width = 0
+first_layer_extrusion_width = 150%
first_layer_height = 0.2
-first_layer_speed = 15
+first_layer_speed = 20
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
-infill_speed = 0
+infill_speed = 40
interface_shells = 0
layer_height = 0.2
-max_print_speed = 60
+max_print_speed = 40
+max_volumetric_extrusion_rate_slope_negative = 0
+max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
-min_skirt_length = 1
+min_skirt_length = 0
notes =
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
-perimeter_speed = 0
-perimeters = 2
+perimeter_speed = 40
+perimeters = 3
post_process =
+print_settings_id =
raft_layers = 0
resolution = 0
seam_position = aligned
-skirt_distance = 1
+skirt_distance = 6
skirt_height = 1
-skirts = 1
+skirts = 3
small_perimeter_speed = 15
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
-solid_infill_speed = 0
+solid_infill_speed = 20
spiral_vase = 0
standby_temperature_delta = -5
-support_material = 0
+support_material = 1
support_material_angle = 0
-support_material_contact_distance = 0
+support_material_buildplate_only = 0
+support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
+support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
-support_material_interface_layers = 2
+support_material_interface_layers = 3
support_material_interface_spacing = 0
-support_material_interface_speed = 10
+support_material_interface_speed = 30
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 40
-support_material_threshold = 40
+support_material_synchronize_layers = 0
+support_material_threshold = 0
+support_material_with_sheath = 1
+support_material_xy_spacing = 50%
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
-top_solid_infill_speed = 20
-top_solid_layers = 3
-travel_speed = 100
+top_solid_infill_speed = 15
+top_solid_layers = 4
+travel_speed = 60
+wipe_tower = 0
+wipe_tower_per_color_wipe = 15
+wipe_tower_width = 60
+wipe_tower_x = 180
+wipe_tower_y = 140
xy_size_compensation = 0
-[print:Prusa i3 200 support]
-avoid_crossing_perimeters = 0
-bottom_solid_layers = 3
+[print:Tiny print]
+avoid_crossing_perimeters = 1
+bottom_solid_layers = 2
bridge_acceleration = 0
+bridge_angle = 0
bridge_flow_ratio = 1
-bridge_speed = 40
-brim_width = 5
+bridge_speed = 60
+brim_width = 2
+clip_multipart_objects = 0
+compatible_printers =
+compatible_printers_condition =
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
+elefant_foot_compensation = 0
+ensure_vertical_shell_thickness = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
-external_perimeter_speed = 20
+external_perimeter_speed = 30
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
-fill_density = 20%
-fill_pattern = 3dhoneycomb
+fill_density = 10%
+fill_pattern = rectilinear
first_layer_acceleration = 0
-first_layer_extrusion_width = 0
+first_layer_extrusion_width = 120%
first_layer_height = 0.2
-first_layer_speed = 15
+first_layer_speed = 20
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
-infill_speed = 0
+infill_speed = 80
interface_shells = 0
layer_height = 0.2
-max_print_speed = 60
+max_print_speed = 100
+max_volumetric_extrusion_rate_slope_negative = 0
+max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
-min_skirt_length = 1
+min_skirt_length = 0
notes =
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
-perimeter_speed = 0
+perimeter_speed = 60
perimeters = 2
post_process =
-raft_layers = 1
+print_settings_id =
+raft_layers = 0
resolution = 0
-seam_position = aligned
-skirt_distance = 1
+seam_position = nearest
+skirt_distance = 6
skirt_height = 1
-skirts = 1
+skirts = 3
small_perimeter_speed = 15
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
-solid_infill_speed = 0
+solid_infill_speed = 20
spiral_vase = 0
standby_temperature_delta = -5
support_material = 1
support_material_angle = 0
+support_material_buildplate_only = 1
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
+support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
-support_material_interface_layers = 2
+support_material_interface_layers = 3
support_material_interface_spacing = 0
-support_material_interface_speed = 10
+support_material_interface_speed = 30
support_material_pattern = pillars
support_material_spacing = 2.5
-support_material_speed = 40
+support_material_speed = 60
+support_material_synchronize_layers = 1
support_material_threshold = 40
+support_material_with_sheath = 1
+support_material_xy_spacing = 0.4
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
-top_solid_infill_speed = 20
+top_solid_infill_speed = 15
top_solid_layers = 3
-travel_speed = 100
+travel_speed = 130
+wipe_tower = 0
+wipe_tower_per_color_wipe = 15
+wipe_tower_width = 60
+wipe_tower_x = 180
+wipe_tower_y = 140
xy_size_compensation = 0
-[printer:LulzBot]
-bed_shape = 0x0,298x0,298x275,0x275
+[filament:ABS 175]
+bed_temperature = 0
+bridge_fan_speed = 100
+compatible_printers =
+compatible_printers_condition =
+cooling = 0
+disable_fan_first_layers = 3
+end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
+extrusion_multiplier = 1
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_colour = #FFFFFF
+filament_cost = 0
+filament_density = 0
+filament_diameter = 1.75
+filament_max_volumetric_speed = 0
+filament_notes = ""
+filament_settings_id =
+filament_soluble = 0
+filament_type = PLA
+first_layer_bed_temperature = 0
+first_layer_temperature = 245
+max_fan_speed = 100
+min_fan_speed = 100
+min_print_speed = 5
+slowdown_below_layer_time = 20
+start_filament_gcode = "; Filament gcode\n"
+temperature = 235
+
+[filament:PETG 175]
+bed_temperature = 0
+bridge_fan_speed = 100
+compatible_printers =
+compatible_printers_condition =
+cooling = 0
+disable_fan_first_layers = 5
+end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
+extrusion_multiplier = 1
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_colour = #FFFFFF
+filament_cost = 27.4375
+filament_density = 1.27
+filament_diameter = 1.75
+filament_max_volumetric_speed = 0
+filament_notes = ""
+filament_settings_id =
+filament_soluble = 0
+filament_type = PET
+first_layer_bed_temperature = 0
+first_layer_temperature = 245
+max_fan_speed = 100
+min_fan_speed = 100
+min_print_speed = 5
+slowdown_below_layer_time = 20
+start_filament_gcode = "; Filament gcode\n"
+temperature = 220
+
+[filament:PETG 285]
+bed_temperature = 75
+bridge_fan_speed = 100
+compatible_printers =
+compatible_printers_condition =
+cooling = 1
+disable_fan_first_layers = 3
+end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
+extrusion_multiplier = 0.9
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_colour = #FFFFFF
+filament_cost = 27.4375
+filament_density = 1.27
+filament_diameter = 2.85
+filament_max_volumetric_speed = 0
+filament_notes = ""
+filament_settings_id =
+filament_soluble = 0
+filament_type = PLA
+first_layer_bed_temperature = 75
+first_layer_temperature = 250
+max_fan_speed = 100
+min_fan_speed = 100
+min_print_speed = 5
+slowdown_below_layer_time = 20
+start_filament_gcode = "; Filament gcode\n"
+temperature = 220
+
+[filament:PLA 175]
+bed_temperature = 0
+bridge_fan_speed = 100
+compatible_printers =
+compatible_printers_condition =
+cooling = 1
+disable_fan_first_layers = 3
+end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
+extrusion_multiplier = 1
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_colour = #FFFFFF
+filament_cost = 0
+filament_density = 0
+filament_diameter = 1.75
+filament_max_volumetric_speed = 0
+filament_notes = ""
+filament_settings_id =
+filament_soluble = 0
+filament_type = PLA
+first_layer_bed_temperature = 0
+first_layer_temperature = 230
+max_fan_speed = 60
+min_fan_speed = 35
+min_print_speed = 5
+slowdown_below_layer_time = 10
+start_filament_gcode = "; Filament gcode\n"
+temperature = 200
+
+[filament:PLA 285]
+bed_temperature = 60
+bridge_fan_speed = 100
+compatible_printers =
+compatible_printers_condition =
+cooling = 1
+disable_fan_first_layers = 10
+end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
+extrusion_multiplier = 1
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_colour = #FFFFFF
+filament_cost = 0
+filament_density = 0
+filament_diameter = 2.85
+filament_max_volumetric_speed = 0
+filament_notes = ""
+filament_settings_id =
+filament_soluble = 0
+filament_type = PLA
+first_layer_bed_temperature = 75
+first_layer_temperature = 230
+max_fan_speed = 100
+min_fan_speed = 100
+min_print_speed = 5
+slowdown_below_layer_time = 20
+start_filament_gcode = "; Filament gcode\n"
+temperature = 220
+
+[filament:WillowFlex 285]
+bed_temperature = 60
+bridge_fan_speed = 100
+compatible_printers =
+compatible_printers_condition =
+cooling = 1
+disable_fan_first_layers = 0
+end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
+extrusion_multiplier = 0.9
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_colour = #FFFFFF
+filament_cost = 27.4375
+filament_density = 1.27
+filament_diameter = 2.85
+filament_max_volumetric_speed = 0
+filament_notes = ""
+filament_settings_id =
+filament_soluble = 0
+filament_type = PLA
+first_layer_bed_temperature = 60
+first_layer_temperature = 175
+max_fan_speed = 100
+min_fan_speed = 100
+min_print_speed = 5
+slowdown_below_layer_time = 20
+start_filament_gcode = "; Filament gcode\n"
+temperature = 175
+
+[printer:Kossel]
+bed_shape = 79.5618x8.36228,78.2518x16.6329,76.0845x24.7214,73.0836x32.5389,69.282x40,64.7214x47.0228,59.4516x53.5304,53.5304x59.4516,47.0228x64.7214,40x69.282,32.5389x73.0836,24.7214x76.0845,16.6329x78.2518,8.36228x79.5618,0x80,-8.36228x79.5618,-16.6329x78.2518,-24.7214x76.0845,-32.5389x73.0836,-40x69.282,-47.0228x64.7214,-53.5304x59.4516,-59.4516x53.5304,-64.7214x47.0228,-69.282x40,-73.0836x32.5389,-76.0845x24.7214,-78.2518x16.6329,-79.5618x8.36228,-80x0,-79.5618x-8.36228,-78.2518x-16.6329,-76.0845x-24.7214,-73.0836x-32.5389,-69.282x-40,-64.7214x-47.0228,-59.4516x-53.5304,-53.5304x-59.4516,-47.0228x-64.7214,-40x-69.282,-32.5389x-73.0836,-24.7214x-76.0845,-16.6329x-78.2518,-8.36228x-79.5618,0x-80,8.36228x-79.5618,16.6329x-78.2518,24.7214x-76.0845,32.5389x-73.0836,40x-69.282,47.0228x-64.7214,53.5304x-59.4516,59.4516x-53.5304,64.7214x-47.0228,69.282x-40,73.0836x-32.5389,76.0845x-24.7214,78.2518x-16.6329,79.5618x-8.36228,80x0
before_layer_gcode =
-end_gcode = M104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200 ;\nG28 X0 ; home X axis\nM84 ; disable motors
-extruder_offset = 0x0
+between_objects_gcode =
+deretract_speed = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
+end_gcode = M104 S0 ; turn off nozzle temperature\nG28; Home\nM84 ; disable motors\nM82; absolute E
+extruder_colour = #FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000
+extruder_offset = 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0
gcode_flavor = reprap
layer_gcode =
-nozzle_diameter = 0.35
+max_layer_height = 0.3,0.3,0.3,0.3,0.3,0.3,0.3,0.3,0.3,0.3,0.3,0.3,0.3,0.3,0.3,0.3
+min_layer_height = 0.07,0.07,0.07,0.07,0.07,0.07,0.07,0.07,0.07,0.07,0.07,0.07,0.07,0.07,0.07,0.07
+nozzle_diameter = 0.4,0.4,0.4,0.4,0.4,0.4,0.4,0.4,0.4,0.4,0.4,0.4,0.4,0.4,0.4,0.4
octoprint_apikey =
octoprint_host =
-pressure_advance = 0
-retract_before_travel = 2
-retract_layer_change = 1
-retract_length = 2
-retract_length_toolchange = 3
-retract_lift = 0
-retract_restart_extra = 0
-retract_restart_extra_toolchange = 0
-retract_speed = 20
-start_gcode = G28 ; home all axes\n
+printer_notes =
+printer_settings_id =
+retract_before_travel = 2,2,2,2,2,2,2,2,2,2,2,2,2,2,2,2
+retract_before_wipe = 0%,0%,0%,0%,0%,0%,0%,0%,0%,0%,0%,0%,0%,0%,0%,0%
+retract_layer_change = 1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1
+retract_length = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
+retract_length_toolchange = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
+retract_lift = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
+retract_lift_above = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
+retract_lift_below = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
+retract_restart_extra = 0.01,0.01,0.01,0.01,0.01,0.01,0.01,0.01,0.01,0.01,0.01,0.01,0.01,0.01,0.01,0.01
+retract_restart_extra_toolchange = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
+retract_speed = 20,20,20,20,20,20,20,20,20,20,20,20,20,20,20,20
+serial_port =
+serial_speed = 250000
+single_extruder_multi_material = 1
+start_gcode = ;M104 S230 ;Temperatur\n;G29 S2 ;Autobed Level\n;G132 S1 ;Store Offset\n\nM83 ;relativ E \n\n; Cyan\nM163 S0 P1\nM163 S1 P0\nM163 S2 P0\nM164 S0\n\n; Ocean\nM163 S0 P5\nM163 S1 P1\nM163 S2 P0\nM164 S1\n\n; Blue\nM163 S0 P1\nM163 S1 P1\nM163 S2 P0\nM164 S2\n\n; Violet\nM163 S0 P1\nM163 S1 P5\nM163 S2 P0\nM164 S3\n\n; Magenta\nM163 S0 P0\nM163 S1 P1\nM163 S2 P0\nM164 S4\n\n; Raspberry\nM163 S0 P0\nM163 S1 P5\nM163 S2 P1\nM164 S5\n\n; Red\nM163 S0 P0\nM163 S1 P5\nM163 S2 P1\nM164 S6\n\n; Orange\nM163 S0 P0\nM163 S1 P1\nM163 S2 P1\nM164 S7\n\n; Yellow\nM163 S0 P0\nM163 S1 P0\nM163 S2 P1\nM164 S8\n\n; Spring Green\nM163 S0 P1\nM163 S1 P0\nM163 S2 P5\nM164 S9\n\n; Green\nM163 S0 P1\nM163 S1 P0\nM163 S2 P1\nM164 S10\n\n; Turquoise\nM163 S0 P5\nM163 S1 P0\nM163 S2 P1\nM164 S11\n\n\n; Cyan-Brown\nM163 S0 P2\nM163 S1 P1\nM163 S2 P1\nM164 S12\n\n; Magenta-Brown\nM163 S0 P1\nM163 S1 P2\nM163 S2 P1\nM164 S13\n\n; Yellow-Brown\nM163 S0 P1\nM163 S1 P1\nM163 S2 P2\nM164 S14\n\n; Brown\nM163 S0 P1\nM163 S1 P1\nM163 S2 P1\nM164 S15\n
toolchange_gcode =
use_firmware_retraction = 0
-use_relative_e_distances = 0
+use_relative_e_distances = 1
use_volumetric_e = 0
-vibration_limit = 0
-wipe = 0
+variable_layer_height = 0
+wipe = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
z_offset = 0
-[printer:MendelPro]
-bed_shape = 0x0,220x0,220x177,0x177
+[printer:Lulzbot]
+bed_shape = 0x0,300x0,300x300,0x300
before_layer_gcode =
-end_gcode = M104 S0 ; turn off temperature\nM140 S0;\nG28 X0 ; home X axis\nG0 Y177;\nM84 ; disable motors\n
+between_objects_gcode =
+deretract_speed = 0
+end_gcode = M104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200 ;\nG28 X0 ; home X axis\nM84 ; disable motors\n\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\n
+extruder_colour = ""
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode =
-nozzle_diameter = 0.5
-octoprint_apikey = 176444E92BFF48819CE0D8F1B264A91C
+max_layer_height = 0.3
+min_layer_height = 0.07
+nozzle_diameter = 0.35
+octoprint_apikey =
octoprint_host =
-pressure_advance = 0
+printer_notes =
+printer_settings_id =
retract_before_travel = 2
+retract_before_wipe = 0%
retract_layer_change = 1
retract_length = 5
-retract_length_toolchange = 10
+retract_length_toolchange = 3
retract_lift = 0
+retract_lift_above = 1
+retract_lift_below = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
-retract_speed = 40
-start_gcode = G28 Z ; home Z\nG28 X Y ; home X Y\n
+retract_speed = 60
+serial_port =
+serial_speed = 250000
+single_extruder_multi_material = 0
+start_gcode = G28 ; home all axes\n
toolchange_gcode =
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
-vibration_limit = 0
-wipe = 0
+variable_layer_height = 0
+wipe = 1
z_offset = 0
-[printer:TinyBoy]
-bed_shape = 0x0,88x0,88x74,0x74
+[printer:Mendel]
+bed_shape = 0x0,218x0,218x201,0x201
before_layer_gcode =
-end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n
+between_objects_gcode =
+deretract_speed = 0
+end_gcode = M104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200 ;\nG28 X0 ; home X axis\nM84 ; disable motors\n\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\n
+extruder_colour = ""
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode =
-nozzle_diameter = 0.4
-octoprint_apikey = 176444E92BFF48819CE0D8F1B264A91C
+max_layer_height = 0.3
+min_layer_height = 0.07
+nozzle_diameter = 0.5
+octoprint_apikey =
octoprint_host =
-pressure_advance = 0
+printer_notes =
+printer_settings_id =
retract_before_travel = 2
+retract_before_wipe = 0%
retract_layer_change = 1
-retract_length = 5
-retract_length_toolchange = 10
+retract_length = 2
+retract_length_toolchange = 3
retract_lift = 0
-retract_restart_extra = 0
+retract_lift_above = 0
+retract_lift_below = 0
+retract_restart_extra = 0.01
retract_restart_extra_toolchange = 0
-retract_speed = 40
-start_gcode = G28 Z ; home Z\nG0 Z 1 ; lift Z\nG28 X Y ; home X Y\n
+retract_speed = 20
+serial_port =
+serial_speed = 250000
+single_extruder_multi_material = 0
+start_gcode = G28 ; home all axes\n
toolchange_gcode =
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
-vibration_limit = 0
+variable_layer_height = 1
wipe = 0
z_offset = 0
-[printer:ToyRep]
-bed_shape = 0x0,125x0,125x125,0x125
+[printer:Tiny]
+bed_shape = 0x0,80x0,80x74,0x74
before_layer_gcode =
-end_gcode = M104 S0 ; turn off nozzle temperature\nM84 ; disable motors
+between_objects_gcode =
+deretract_speed = 0
+end_gcode = M104 S0 ; turn off nozzle temperature\nG28 X0 ; home X axis
+extruder_colour = ""
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode =
+max_layer_height = 0.3
+min_layer_height = 0.07
nozzle_diameter = 0.4
octoprint_apikey =
octoprint_host =
-pressure_advance = 0
+printer_notes =
+printer_settings_id =
retract_before_travel = 2
+retract_before_wipe = 0%
retract_layer_change = 1
-retract_length = 0
+retract_length = 2
retract_length_toolchange = 3
retract_lift = 0
-retract_restart_extra = 0
+retract_lift_above = 1
+retract_lift_below = 0
+retract_restart_extra = 0.01
retract_restart_extra_toolchange = 0
-retract_speed = 10
-start_gcode = \n
+retract_speed = 40
+serial_port =
+serial_speed = 250000
+single_extruder_multi_material = 0
+start_gcode = G28 ; home all axes\n
toolchange_gcode =
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
-vibration_limit = 0
+variable_layer_height = 1
wipe = 0
z_offset = 0
-[printer:Prusa i3]
-bed_shape = 0x0,190x0,190x190,0x190
+[printer:prusa i3]
+bed_shape = 0x0,190x0,190x160,0x160
before_layer_gcode =
+between_objects_gcode =
+deretract_speed = 0
end_gcode = M104 S0 ; turn off temperature\nM140 S0 ; turn off bed temp \nG28 X0 ; home X axis\nG0 Y190 ; präsent object\nM84 ; disable motors\nM81 ; Power off\n\n
+extruder_colour = ""
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode =
+max_layer_height = 0
+min_layer_height = 0.07
nozzle_diameter = 0.4
octoprint_apikey = 176444E92BFF48819CE0D8F1B264A91C
octoprint_host =
-pressure_advance = 0
+printer_notes =
retract_before_travel = 2
+retract_before_wipe = 0%
retract_layer_change = 1
-retract_length = 5
+retract_length = 4
retract_length_toolchange = 10
retract_lift = 0
+retract_lift_above = 0
+retract_lift_below = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
-start_gcode = G28 Z ; home Z\nG0 Z1 ; lift Z\nG28 X Y ; home X Y\nG0 Y40 ; clab move
-toolchange_gcode = M83 ; turn on relative movement for extruder \nG1 E-5 ; retract filament 5mm \nG1 X10 Y10 Z4.000000 ; home X and Y axis leave Z at current height \nM84 E ; release extruder stepper motor from 'holding' position \n@pause ; pause print! \nG1 E0 ; reset extruder, ready to push out plastic again \nM82 ; set extruder movement back to absolute ready for next layer
+serial_port =
+serial_speed = 250000
+single_extruder_multi_material = 0
+start_gcode = G28 Z ; home Z\n;G0 Z1 ; lift Z\nG28 X Y ; home X Y\nG0 Y40 ; clab move
+toolchange_gcode = M83 ; turn on relative movement for extruder \nG1 E-5 ; retract filament 5mm \nG1 X10 Y10 Z4.000000 ; home X and Y axis leave Z at current height \nM84 E ; release extruder stepper motor from 'holding' position \n@pause ; pause print! \nG1 E0 ; reset extruder, ready to push out plastic again \nM82 ; set extruder movement back to absolute ready for next layer
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
-vibration_limit = 0
+variable_layer_height = 1
wipe = 0
z_offset = 0
-[settings]
-autocenter = 1
-mode = expert
+[presets]
+print = Tiny print
+printer = Tiny
+filament = PETG 175
projects / stratum0-wiki.git / blobdiff