-# generated by Slic3r 1.2.9 on Fri May 13 17:04:53 2016
+# generated by Slic3r 1.2.9 on Thu Jun 2 16:16:44 2016
-[filament:LULZBOT ABS fine]
+[filament:Lulzbot ABS]
bed_temperature = 100
-bridge_fan_speed = 0
-cooling = 1
+bridge_fan_speed = 100
+cooling = 0
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #FFFFFF
-filament_diameter = 2.89
+filament_diameter = 2.85
first_layer_bed_temperature = 100
first_layer_temperature = 250
-max_fan_speed = 0
-min_fan_speed = 0
-min_print_speed = 15
+max_fan_speed = 100
+min_fan_speed = 30
+min_print_speed = 10
slowdown_below_layer_time = 20
-temperature = 240
+temperature = 245
+
+[filament:Lulzbot PLA]
+bed_temperature = 50
+bridge_fan_speed = 100
+cooling = 1
+disable_fan_first_layers = 1
+extrusion_multiplier = 1
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_colour = #FFFFFF
+filament_diameter = 2.85
+first_layer_bed_temperature = 55
+first_layer_temperature = 200
+max_fan_speed = 100
+min_fan_speed = 35
+min_print_speed = 10
+slowdown_below_layer_time = 30
+temperature = 190
+
+[filament:Lulzbot PLA Weiß]
+bed_temperature = 50
+bridge_fan_speed = 100
+cooling = 1
+disable_fan_first_layers = 1
+extrusion_multiplier = 1
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_colour = #FFFFFF
+filament_diameter = 2.85
+first_layer_bed_temperature = 55
+first_layer_temperature = 200
+max_fan_speed = 100
+min_fan_speed = 30
+min_print_speed = 10
+slowdown_below_layer_time = 20
+temperature = 190
[filament:MendelPro ABS]
bed_temperature = 0
first_layer_bed_temperature = 55
first_layer_temperature = 200
max_fan_speed = 100
-min_fan_speed = 50
+min_fan_speed = 40
min_print_speed = 5
slowdown_below_layer_time = 30
temperature = 180
+[filament:MendelPro PLA fast]
+bed_temperature = 50
+bridge_fan_speed = 100
+cooling = 1
+disable_fan_first_layers = 1
+extrusion_multiplier = 1
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_colour = #FFFFFF
+filament_diameter = 1.7
+first_layer_bed_temperature = 50
+first_layer_temperature = 200
+max_fan_speed = 100
+min_fan_speed = 50
+min_print_speed = 5
+slowdown_below_layer_time = 30
+temperature = 200
+
+[filament:MendelPro PLA transparent]
+bed_temperature = 50
+bridge_fan_speed = 100
+cooling = 1
+disable_fan_first_layers = 1
+extrusion_multiplier = 1
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_colour = #FFFFFF
+filament_diameter = 1.7
+first_layer_bed_temperature = 55
+first_layer_temperature = 200
+max_fan_speed = 100
+min_fan_speed = 40
+min_print_speed = 5
+slowdown_below_layer_time = 30
+temperature = 200
+
[filament:TinyBoy PLA]
bed_temperature = 0
bridge_fan_speed = 100
slowdown_below_layer_time = 15
temperature = 185
-[filament:prusa i3 PLA black fine]
-bed_temperature = 50
+[filament:Toy]
+bed_temperature = 0
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 60
-filament_colour = #FF0000
-filament_diameter = 2.9
-first_layer_bed_temperature = 50
+filament_colour = #FFFFFF
+filament_diameter = 1.7
+first_layer_bed_temperature = 0
first_layer_temperature = 200
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 5
-slowdown_below_layer_time = 15
-temperature = 200
+slowdown_below_layer_time = 30
+temperature = 180
-[filament:prusa i3 PLA igus]
+[filament:prusa i3 PLA black fine]
bed_temperature = 50
bridge_fan_speed = 100
-cooling = 0
+cooling = 1
disable_fan_first_layers = 1
-extrusion_multiplier = 0.9
-fan_always_on = 0
+extrusion_multiplier = 1
+fan_always_on = 1
fan_below_layer_time = 60
-filament_colour = #D0C9B0
+filament_colour = #FF0000
filament_diameter = 2.9
first_layer_bed_temperature = 50
-first_layer_temperature = 250
+first_layer_temperature = 200
max_fan_speed = 100
-min_fan_speed = 35
+min_fan_speed = 100
min_print_speed = 5
slowdown_below_layer_time = 15
-temperature = 250
+temperature = 200
-[filament:prusa i3 PLA rot]
+[filament:prusa i3 PLA lila]
bed_temperature = 50
bridge_fan_speed = 100
cooling = 1
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 60
-filament_colour = #FF0000
-filament_diameter = 2.9
+filament_colour = #8000FF
+filament_diameter = 3
first_layer_bed_temperature = 50
first_layer_temperature = 200
max_fan_speed = 100
temperature = 200
[presets]
-filament = LULZBOT ABS fine.ini
-print = prusa i3 100.ini
-printer = LULZBOT ABS fine.ini
+filament = MendelPro PLA fast.ini
+print = Lulzbot fine.ini
+printer = Lulzbot.ini
-[print:LULZBOT ABS fine ]
+[print:Lulzbot fine]
avoid_crossing_perimeters = 1
-bottom_solid_layers = 2
-bridge_acceleration = 1000
-bridge_flow_ratio = 1.1
+bottom_solid_layers = 4
+bridge_acceleration = 0
+bridge_flow_ratio = 1
bridge_speed = 40
brim_width = 0
complete_objects = 0
-default_acceleration = 900
+default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
-extrusion_width = 0.37
+extrusion_width = 0
fill_angle = 35
fill_density = 30%
fill_pattern = line
first_layer_acceleration = 0
-first_layer_extrusion_width = 0.37
-first_layer_height = 120%
-first_layer_speed = 85%
-gap_fill_speed = 45
+first_layer_extrusion_width = 0
+first_layer_height = 0.2
+first_layer_speed = 10
+gap_fill_speed = 20
gcode_comments = 0
-infill_acceleration = 1400
+infill_acceleration = 0
infill_every_layers = 2
infill_extruder = 1
-infill_extrusion_width = 0.6
+infill_extrusion_width = 110%
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
-infill_speed = 70
+infill_speed = 0
interface_shells = 0
-layer_height = 0.14
-max_print_speed = 80
+layer_height = 0.25
+max_print_speed = 100
max_volumetric_speed = 0
min_skirt_length = 0
notes =
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
-perimeter_acceleration = 900
+perimeter_acceleration = 0
perimeter_extruder = 1
-perimeter_extrusion_width = 0.34
-perimeter_speed = 40
-perimeters = 4
+perimeter_extrusion_width = 0
+perimeter_speed = 0
+perimeters = 3
post_process =
raft_layers = 0
resolution = 0
skirt_distance = 6
skirt_height = 1
skirts = 2
-small_perimeter_speed = 30
+small_perimeter_speed = 20
solid_infill_below_area = 30
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
-solid_infill_speed = 60
+solid_infill_speed = 0
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
-support_material_speed = 60
+support_material_speed = 0
support_material_threshold = 45
thin_walls = 1
threads = 2
-top_infill_extrusion_width = 0.35
-top_solid_infill_speed = 80%
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 30
top_solid_layers = 4
-travel_speed = 80
+travel_speed = 100
xy_size_compensation = 0
[print:MendelPro]
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1
-bridge_speed = 35
+bridge_speed = 40
brim_width = 0
complete_objects = 0
default_acceleration = 0
fill_density = 15%
fill_pattern = rectilinear
first_layer_acceleration = 0
-first_layer_extrusion_width = 150%
+first_layer_extrusion_width = 0
first_layer_height = 0.2
first_layer_speed = 10
gap_fill_speed = 10
infill_speed = 0
interface_shells = 0
layer_height = 0.2
-max_print_speed = 35
+max_print_speed = 80
max_volumetric_speed = 0
-min_skirt_length = 1
+min_skirt_length = 2
+notes =
+only_retract_when_crossing_perimeters = 1
+ooze_prevention = 0
+output_filename_format = [input_filename_base].gcode
+overhangs = 1
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 0
+perimeters = 2
+post_process =
+raft_layers = 0
+resolution = 0
+seam_position = aligned
+skirt_distance = 1
+skirt_height = 1
+skirts = 1
+small_perimeter_speed = 10
+solid_infill_below_area = 70
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 0
+solid_infill_speed = 0
+spiral_vase = 0
+standby_temperature_delta = -5
+support_material = 0
+support_material_angle = 0
+support_material_contact_distance = 0.2
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_extruder = 1
+support_material_interface_layers = 2
+support_material_interface_spacing = 0
+support_material_interface_speed = 100%
+support_material_pattern = rectilinear
+support_material_spacing = 5
+support_material_speed = 0
+support_material_threshold = 40
+thin_walls = 1
+threads = 2
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 20
+top_solid_layers = 3
+travel_speed = 100
+xy_size_compensation = 0
+
+[print:MendelPro fast]
+avoid_crossing_perimeters = 0
+bottom_solid_layers = 3
+bridge_acceleration = 0
+bridge_flow_ratio = 1
+bridge_speed = 40
+brim_width = 0
+complete_objects = 0
+default_acceleration = 0
+dont_support_bridges = 1
+external_fill_pattern = rectilinear
+external_perimeter_extrusion_width = 0
+external_perimeter_speed = 20
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extrusion_width = 0
+fill_angle = 45
+fill_density = 15%
+fill_pattern = rectilinear
+first_layer_acceleration = 0
+first_layer_extrusion_width = 0
+first_layer_height = 0.2
+first_layer_speed = 10
+gap_fill_speed = 10
+gcode_comments = 0
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap = 15%
+infill_speed = 0
+interface_shells = 0
+layer_height = 0.5
+max_print_speed = 80
+max_volumetric_speed = 0
+min_skirt_length = 2
notes =
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
travel_speed = 100
xy_size_compensation = 0
-[print:prusa i3 100]
+[print:Toy]
avoid_crossing_perimeters = 0
-bottom_solid_layers = 3
+bottom_solid_layers = 2
bridge_acceleration = 0
bridge_flow_ratio = 1
-bridge_speed = 40
+bridge_speed = 0
brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
-external_perimeter_speed = 10
+external_perimeter_speed = 0
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
-fill_density = 20%
+fill_density = 0%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 0
first_layer_height = 0.2
first_layer_speed = 10
-gap_fill_speed = 10
+gap_fill_speed = 0
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
-infill_extrusion_width = 110%
+infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 0
interface_shells = 0
-layer_height = 0.1
-max_print_speed = 80
+layer_height = 0.2
+max_print_speed = 10
max_volumetric_speed = 0
min_skirt_length = 1
notes =
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 0
-perimeters = 3
+perimeters = 2
post_process =
raft_layers = 0
resolution = 0
seam_position = aligned
-skirt_distance = 6
+skirt_distance = 1
skirt_height = 1
-skirts = 3
-small_perimeter_speed = 10
+skirts = 1
+small_perimeter_speed = 0
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
-top_solid_infill_speed = 10
-top_solid_layers = 3
+top_solid_infill_speed = 0
+top_solid_layers = 0
travel_speed = 100
xy_size_compensation = 0
-[print:prusa i3 100 testtesttest]
+[print:prusa i3 100]
avoid_crossing_perimeters = 0
-bottom_solid_layers = 0
+bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 40
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
-fill_density = 0%
+fill_density = 20%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 0
-perimeters = 1
+perimeters = 3
post_process =
raft_layers = 0
resolution = 0
seam_position = aligned
-skirt_distance = 1
+skirt_distance = 6
skirt_height = 1
-skirts = 1
+skirts = 3
small_perimeter_speed = 10
solid_infill_below_area = 70
solid_infill_every_layers = 0
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 10
-top_solid_layers = 0
+top_solid_layers = 3
travel_speed = 100
xy_size_compensation = 0
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1
-bridge_speed = 40
+bridge_speed = 60
brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
-external_perimeter_speed = 10
+external_perimeter_speed = 20
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
-infill_extrusion_width = 110%
+infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
standby_temperature_delta = -5
support_material = 1
support_material_angle = 0
-support_material_contact_distance = 0.2
+support_material_contact_distance = 0.3
support_material_enforce_layers = 0
support_material_extruder = 1
-support_material_extrusion_width = 0
+support_material_extrusion_width = 90%
support_material_interface_extruder = 1
support_material_interface_layers = 2
-support_material_interface_spacing = 0
+support_material_interface_spacing = 2
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 5
travel_speed = 100
xy_size_compensation = 0
-[printer:LULZBOT ABS fine]
+[printer:Lulzbot]
bed_shape = 0x0,298x0,298x275,0x275
before_layer_gcode =
end_gcode = M104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200 ;\nG28 X0 ; home X axis\nM84 ; disable motors
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 20
-start_gcode = G28 ; home all axes
+start_gcode = G28 ; home all axes\n
toolchange_gcode =
use_firmware_retraction = 0
use_relative_e_distances = 0
[printer:MendelPro]
bed_shape = 0x0,220x0,220x177,0x177
before_layer_gcode =
-end_gcode = M104 S0 ; turn off temperature\nM140 S0;\nG28 X0 ; home X axis\nM84 ; disable motors\n
+end_gcode = M104 S0 ; turn off temperature\nM140 S0;\nG28 X0 ; home X axis\nG0 Y177;\nM84 ; disable motors\n
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode =
wipe = 0
z_offset = 0
+[printer:Toyrep]
+bed_shape = 0x0,125x0,125x125,0x125
+before_layer_gcode =
+end_gcode = M104 S0 ; turn off nozzle temperature\nM84 ; disable motors
+extruder_offset = 0x0
+gcode_flavor = reprap
+layer_gcode =
+nozzle_diameter = 0.4
+octoprint_apikey =
+octoprint_host =
+pressure_advance = 0
+retract_before_travel = 2
+retract_layer_change = 1
+retract_length = 0
+retract_length_toolchange = 3
+retract_lift = 0
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 10
+start_gcode = \n
+toolchange_gcode =
+use_firmware_retraction = 0
+use_relative_e_distances = 0
+use_volumetric_e = 0
+vibration_limit = 0
+wipe = 0
+z_offset = 0
+
[printer:prusa i3]
bed_shape = 0x0,190x0,190x190,0x190
before_layer_gcode =
projects / stratum0-wiki.git / blobdiff