-# generated by Slic3r 1.2.9 on Fri May 13 17:04:53 2016
+# generated by Slic3r 1.2.9 on Mon Nov 21 19:45:57 2016
-[filament:LULZBOT ABS fine]
-bed_temperature = 100
-bridge_fan_speed = 0
+[filament:1.75mm ABS]
+bed_temperature = 0
+bridge_fan_speed = 50
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #FFFFFF
-filament_diameter = 2.89
-first_layer_bed_temperature = 100
-first_layer_temperature = 250
+filament_diameter = 1.75
+first_layer_bed_temperature = 0
+first_layer_temperature = 240
max_fan_speed = 0
min_fan_speed = 0
-min_print_speed = 15
-slowdown_below_layer_time = 20
-temperature = 240
-
-[filament:MendelPro ABS]
-bed_temperature = 0
-bridge_fan_speed = 100
-cooling = 0
-disable_fan_first_layers = 1
-extrusion_multiplier = 1
-fan_always_on = 0
-fan_below_layer_time = 60
-filament_colour = #FFFFFF
-filament_diameter = 1.7
-first_layer_bed_temperature = 0
-first_layer_temperature = 250
-max_fan_speed = 100
-min_fan_speed = 50
min_print_speed = 5
slowdown_below_layer_time = 30
-temperature = 245
+temperature = 230
-[filament:MendelPro Holz]
+[filament:1.75mm Holz]
bed_temperature = 50
bridge_fan_speed = 100
cooling = 1
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #FFFFFF
-filament_diameter = 1.7
-first_layer_bed_temperature = 55
+filament_diameter = 1.75
+first_layer_bed_temperature = 50
first_layer_temperature = 200
max_fan_speed = 100
min_fan_speed = 50
min_print_speed = 5
slowdown_below_layer_time = 30
-temperature = 185
+temperature = 190
-[filament:MendelPro PLA]
+[filament:1.75mm PLA]
bed_temperature = 50
bridge_fan_speed = 100
cooling = 1
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #FFFFFF
-filament_diameter = 1.7
-first_layer_bed_temperature = 55
+filament_diameter = 1.75
+first_layer_bed_temperature = 50
first_layer_temperature = 200
max_fan_speed = 100
min_fan_speed = 50
min_print_speed = 5
-slowdown_below_layer_time = 30
-temperature = 180
+slowdown_below_layer_time = 15
+temperature = 185
-[filament:TinyBoy PLA]
+[filament:1.75mm PLA TinyBoy]
bed_temperature = 0
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 2
-extrusion_multiplier = 0.9
+extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 60
-filament_colour = #35E1FF
-filament_diameter = 1.7
+filament_colour = #FF8000
+filament_diameter = 1.75
first_layer_bed_temperature = 0
first_layer_temperature = 200
-max_fan_speed = 50
+max_fan_speed = 40
min_fan_speed = 35
min_print_speed = 5
slowdown_below_layer_time = 15
-temperature = 185
+temperature = 190
-[filament:prusa i3 PLA black fine]
-bed_temperature = 50
+[filament:2.85mm ABS]
+bed_temperature = 100
+bridge_fan_speed = 50
+cooling = 1
+disable_fan_first_layers = 1
+extrusion_multiplier = 1
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_colour = #FFFFFF
+filament_diameter = 2.85
+first_layer_bed_temperature = 100
+first_layer_temperature = 250
+max_fan_speed = 0
+min_fan_speed = 0
+min_print_speed = 5
+slowdown_below_layer_time = 20
+temperature = 230
+
+[filament:2.85mm PETG ]
+bed_temperature = 75
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 60
-filament_colour = #FF0000
-filament_diameter = 2.9
-first_layer_bed_temperature = 50
-first_layer_temperature = 200
+filament_colour = #B1EB96
+filament_diameter = 2.85
+first_layer_bed_temperature = 75
+first_layer_temperature = 235
max_fan_speed = 100
-min_fan_speed = 100
-min_print_speed = 5
-slowdown_below_layer_time = 15
-temperature = 200
+min_fan_speed = 50
+min_print_speed = 10
+slowdown_below_layer_time = 30
+temperature = 235
-[filament:prusa i3 PLA igus]
+[filament:2.85mm PLA]
bed_temperature = 50
bridge_fan_speed = 100
-cooling = 0
+cooling = 1
disable_fan_first_layers = 1
-extrusion_multiplier = 0.9
-fan_always_on = 0
+extrusion_multiplier = 1
+fan_always_on = 1
fan_below_layer_time = 60
-filament_colour = #D0C9B0
-filament_diameter = 2.9
+filament_colour = #FF00FF
+filament_diameter = 2.85
first_layer_bed_temperature = 50
-first_layer_temperature = 250
+first_layer_temperature = 200
max_fan_speed = 100
min_fan_speed = 35
-min_print_speed = 5
-slowdown_below_layer_time = 15
-temperature = 250
+min_print_speed = 10
+slowdown_below_layer_time = 10
+temperature = 185
-[filament:prusa i3 PLA rot]
-bed_temperature = 50
+[filament:2.85mm Willowflex]
+bed_temperature = 70
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 60
-filament_colour = #FF0000
-filament_diameter = 2.9
-first_layer_bed_temperature = 50
-first_layer_temperature = 200
+filament_colour = #BF0005
+filament_diameter = 2.85
+first_layer_bed_temperature = 70
+first_layer_temperature = 160
max_fan_speed = 100
min_fan_speed = 35
-min_print_speed = 5
-slowdown_below_layer_time = 15
-temperature = 200
+min_print_speed = 10
+slowdown_below_layer_time = 10
+temperature = 160
[presets]
-filament = LULZBOT ABS fine.ini
-print = prusa i3 100.ini
-printer = LULZBOT ABS fine.ini
-
-[print:LULZBOT ABS fine ]
-avoid_crossing_perimeters = 1
-bottom_solid_layers = 2
-bridge_acceleration = 1000
-bridge_flow_ratio = 1.1
-bridge_speed = 40
-brim_width = 0
-complete_objects = 0
-default_acceleration = 900
-dont_support_bridges = 1
-external_fill_pattern = rectilinear
-external_perimeter_extrusion_width = 0
-external_perimeter_speed = 30
-external_perimeters_first = 0
-extra_perimeters = 1
-extruder_clearance_height = 20
-extruder_clearance_radius = 20
-extrusion_width = 0.37
-fill_angle = 35
-fill_density = 30%
-fill_pattern = line
-first_layer_acceleration = 0
-first_layer_extrusion_width = 0.37
-first_layer_height = 120%
-first_layer_speed = 85%
-gap_fill_speed = 45
-gcode_comments = 0
-infill_acceleration = 1400
-infill_every_layers = 2
-infill_extruder = 1
-infill_extrusion_width = 0.6
-infill_first = 0
-infill_only_where_needed = 0
-infill_overlap = 15%
-infill_speed = 70
-interface_shells = 0
-layer_height = 0.14
-max_print_speed = 80
-max_volumetric_speed = 0
-min_skirt_length = 0
-notes =
-only_retract_when_crossing_perimeters = 0
-ooze_prevention = 0
-output_filename_format = [input_filename_base].gcode
-overhangs = 1
-perimeter_acceleration = 900
-perimeter_extruder = 1
-perimeter_extrusion_width = 0.34
-perimeter_speed = 40
-perimeters = 4
-post_process =
-raft_layers = 0
-resolution = 0
-seam_position = aligned
-skirt_distance = 6
-skirt_height = 1
-skirts = 2
-small_perimeter_speed = 30
-solid_infill_below_area = 30
-solid_infill_every_layers = 0
-solid_infill_extruder = 1
-solid_infill_extrusion_width = 0
-solid_infill_speed = 60
-spiral_vase = 0
-standby_temperature_delta = -5
-support_material = 0
-support_material_angle = 0
-support_material_contact_distance = 0.2
-support_material_enforce_layers = 0
-support_material_extruder = 1
-support_material_extrusion_width = 0
-support_material_interface_extruder = 1
-support_material_interface_layers = 0
-support_material_interface_spacing = 0
-support_material_interface_speed = 100%
-support_material_pattern = rectilinear
-support_material_spacing = 2.5
-support_material_speed = 60
-support_material_threshold = 45
-thin_walls = 1
-threads = 2
-top_infill_extrusion_width = 0.35
-top_solid_infill_speed = 80%
-top_solid_layers = 4
-travel_speed = 80
-xy_size_compensation = 0
-
-[print:MendelPro]
-avoid_crossing_perimeters = 0
-bottom_solid_layers = 3
-bridge_acceleration = 0
-bridge_flow_ratio = 1
-bridge_speed = 35
-brim_width = 0
-complete_objects = 0
-default_acceleration = 0
-dont_support_bridges = 1
-external_fill_pattern = rectilinear
-external_perimeter_extrusion_width = 0
-external_perimeter_speed = 20
-external_perimeters_first = 0
-extra_perimeters = 1
-extruder_clearance_height = 20
-extruder_clearance_radius = 20
-extrusion_width = 0
-fill_angle = 45
-fill_density = 15%
-fill_pattern = rectilinear
-first_layer_acceleration = 0
-first_layer_extrusion_width = 150%
-first_layer_height = 0.2
-first_layer_speed = 10
-gap_fill_speed = 10
-gcode_comments = 0
-infill_acceleration = 0
-infill_every_layers = 1
-infill_extruder = 1
-infill_extrusion_width = 0
-infill_first = 0
-infill_only_where_needed = 0
-infill_overlap = 15%
-infill_speed = 0
-interface_shells = 0
-layer_height = 0.2
-max_print_speed = 35
-max_volumetric_speed = 0
-min_skirt_length = 1
-notes =
-only_retract_when_crossing_perimeters = 1
-ooze_prevention = 0
-output_filename_format = [input_filename_base].gcode
-overhangs = 1
-perimeter_acceleration = 0
-perimeter_extruder = 1
-perimeter_extrusion_width = 0
-perimeter_speed = 0
-perimeters = 2
-post_process =
-raft_layers = 0
-resolution = 0
-seam_position = aligned
-skirt_distance = 1
-skirt_height = 1
-skirts = 1
-small_perimeter_speed = 10
-solid_infill_below_area = 70
-solid_infill_every_layers = 0
-solid_infill_extruder = 1
-solid_infill_extrusion_width = 0
-solid_infill_speed = 0
-spiral_vase = 0
-standby_temperature_delta = -5
-support_material = 0
-support_material_angle = 0
-support_material_contact_distance = 0.2
-support_material_enforce_layers = 0
-support_material_extruder = 1
-support_material_extrusion_width = 0
-support_material_interface_extruder = 1
-support_material_interface_layers = 2
-support_material_interface_spacing = 0
-support_material_interface_speed = 100%
-support_material_pattern = rectilinear
-support_material_spacing = 5
-support_material_speed = 0
-support_material_threshold = 40
-thin_walls = 1
-threads = 2
-top_infill_extrusion_width = 0
-top_solid_infill_speed = 20
-top_solid_layers = 3
-travel_speed = 100
-xy_size_compensation = 0
+filament = 2.85mm Willowflex.ini
+print = prusa i3.ini
+printer = prusa i3.ini
-[print:TinyBoy]
+[print:Lulzbot]
avoid_crossing_perimeters = 0
-bottom_solid_layers = 3
+bottom_solid_layers = 4
bridge_acceleration = 0
bridge_flow_ratio = 1
-bridge_speed = 0
-brim_width = 0
-complete_objects = 0
-default_acceleration = 0
-dont_support_bridges = 1
-external_fill_pattern = rectilinear
-external_perimeter_extrusion_width = 0
-external_perimeter_speed = 0
-external_perimeters_first = 0
-extra_perimeters = 1
-extruder_clearance_height = 20
-extruder_clearance_radius = 20
-extrusion_width = 0
-fill_angle = 45
-fill_density = 15%
-fill_pattern = rectilinear
-first_layer_acceleration = 0
-first_layer_extrusion_width = 150%
-first_layer_height = 0.2
-first_layer_speed = 20
-gap_fill_speed = 0
-gcode_comments = 0
-infill_acceleration = 0
-infill_every_layers = 1
-infill_extruder = 1
-infill_extrusion_width = 0
-infill_first = 0
-infill_only_where_needed = 0
-infill_overlap = 15%
-infill_speed = 0
-interface_shells = 0
-layer_height = 0.2
-max_print_speed = 50
-max_volumetric_speed = 0
-min_skirt_length = 1
-notes =
-only_retract_when_crossing_perimeters = 1
-ooze_prevention = 0
-output_filename_format = [input_filename_base].gcode
-overhangs = 1
-perimeter_acceleration = 0
-perimeter_extruder = 1
-perimeter_extrusion_width = 0
-perimeter_speed = 0
-perimeters = 2
-post_process =
-raft_layers = 0
-resolution = 0
-seam_position = aligned
-skirt_distance = 1
-skirt_height = 1
-skirts = 1
-small_perimeter_speed = 0
-solid_infill_below_area = 70
-solid_infill_every_layers = 0
-solid_infill_extruder = 1
-solid_infill_extrusion_width = 0
-solid_infill_speed = 0
-spiral_vase = 0
-standby_temperature_delta = -5
-support_material = 0
-support_material_angle = 0
-support_material_contact_distance = 0.2
-support_material_enforce_layers = 0
-support_material_extruder = 1
-support_material_extrusion_width = 0
-support_material_interface_extruder = 1
-support_material_interface_layers = 2
-support_material_interface_spacing = 0
-support_material_interface_speed = 100%
-support_material_pattern = rectilinear
-support_material_spacing = 5
-support_material_speed = 0
-support_material_threshold = 40
-thin_walls = 1
-threads = 2
-top_infill_extrusion_width = 0
-top_solid_infill_speed = 0
-top_solid_layers = 3
-travel_speed = 100
-xy_size_compensation = 0
-
-[print:prusa i3 100]
-avoid_crossing_perimeters = 0
-bottom_solid_layers = 3
-bridge_acceleration = 0
-bridge_flow_ratio = 1
-bridge_speed = 40
-brim_width = 0
+bridge_speed = 60
+brim_width = 1
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
-external_perimeter_speed = 10
+external_perimeter_speed = 40
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
-fill_angle = 45
+fill_angle = 35
fill_density = 20%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 0
first_layer_height = 0.2
first_layer_speed = 10
-gap_fill_speed = 10
+gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
-infill_extrusion_width = 110%
+infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
-infill_speed = 0
+infill_speed = 80
interface_shells = 0
-layer_height = 0.1
-max_print_speed = 80
+layer_height = 0.2
+max_print_speed = 100
max_volumetric_speed = 0
-min_skirt_length = 1
+min_skirt_length = 3
notes =
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
-perimeter_speed = 0
+perimeter_speed = 80
perimeters = 3
post_process =
raft_layers = 0
resolution = 0
-seam_position = aligned
+seam_position = nearest
skirt_distance = 6
skirt_height = 1
-skirts = 3
-small_perimeter_speed = 10
-solid_infill_below_area = 70
+skirts = 1
+small_perimeter_speed = 15
+solid_infill_below_area = 30
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
-solid_infill_speed = 0
+solid_infill_speed = 60
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
-support_material_interface_layers = 2
+support_material_interface_layers = 3
support_material_interface_spacing = 0
-support_material_interface_speed = 100%
+support_material_interface_speed = 40
support_material_pattern = rectilinear
-support_material_spacing = 5
-support_material_speed = 0
-support_material_threshold = 40
+support_material_spacing = 2.5
+support_material_speed = 60
+support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
-top_solid_infill_speed = 10
-top_solid_layers = 3
-travel_speed = 100
+top_solid_infill_speed = 40
+top_solid_layers = 4
+travel_speed = 130
xy_size_compensation = 0
-[print:prusa i3 100 testtesttest]
+[print:MendelPro]
avoid_crossing_perimeters = 0
-bottom_solid_layers = 0
+bottom_solid_layers = 4
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 40
-brim_width = 0
+brim_width = 1
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
-external_perimeter_speed = 10
+external_perimeter_speed = 30
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
-fill_density = 0%
+fill_density = 20%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
-infill_extrusion_width = 110%
+infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 0
interface_shells = 0
-layer_height = 0.1
+layer_height = 0.2
max_print_speed = 80
max_volumetric_speed = 0
-min_skirt_length = 1
+min_skirt_length = 2
notes =
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 0
-perimeters = 1
+perimeters = 2
post_process =
raft_layers = 0
resolution = 0
-seam_position = aligned
-skirt_distance = 1
+seam_position = nearest
+skirt_distance = 10
skirt_height = 1
skirts = 1
small_perimeter_speed = 10
solid_infill_speed = 0
spiral_vase = 0
standby_temperature_delta = -5
-support_material = 0
+support_material = 1
support_material_angle = 0
-support_material_contact_distance = 0.2
+support_material_contact_distance = 0.4
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
-support_material_interface_layers = 2
+support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
-support_material_pattern = rectilinear
-support_material_spacing = 5
-support_material_speed = 0
-support_material_threshold = 40
+support_material_pattern = pillars
+support_material_spacing = 3
+support_material_speed = 60
+support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
-top_solid_infill_speed = 10
-top_solid_layers = 0
+top_solid_infill_speed = 20
+top_solid_layers = 4
travel_speed = 100
xy_size_compensation = 0
-[print:prusa i3 250]
+[print:TinyBoy]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
-external_perimeter_speed = 10
+external_perimeter_speed = 20
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extrusion_width = 0
fill_angle = 45
fill_density = 20%
-fill_pattern = rectilinear
+fill_pattern = 3dhoneycomb
first_layer_acceleration = 0
first_layer_extrusion_width = 0
first_layer_height = 0.2
-first_layer_speed = 15
-gap_fill_speed = 10
+first_layer_speed = 10
+gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
-infill_extrusion_width = 110%
+infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 0
interface_shells = 0
-layer_height = 0.25
-max_print_speed = 60
+layer_height = 0.2
+max_print_speed = 80
max_volumetric_speed = 0
min_skirt_length = 1
notes =
post_process =
raft_layers = 0
resolution = 0
-seam_position = aligned
+seam_position = nearest
skirt_distance = 1
skirt_height = 1
skirts = 1
-small_perimeter_speed = 10
+small_perimeter_speed = 0
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 20
-top_solid_layers = 3
+top_solid_layers = 4
travel_speed = 100
xy_size_compensation = 0
-[print:prusa i3 400]
+[print:Toy]
avoid_crossing_perimeters = 0
-bottom_solid_layers = 3
+bottom_solid_layers = 2
bridge_acceleration = 0
bridge_flow_ratio = 1
-bridge_speed = 60
+bridge_speed = 0
brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
-external_perimeter_speed = 20
+external_perimeter_speed = 0
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
-fill_density = 20%
+fill_density = 0%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 0
first_layer_height = 0.2
first_layer_speed = 10
-gap_fill_speed = 10
+gap_fill_speed = 0
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
-infill_extrusion_width = 110%
+infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 0
interface_shells = 0
-layer_height = 0.4
-max_print_speed = 80
+layer_height = 0.2
+max_print_speed = 10
max_volumetric_speed = 0
min_skirt_length = 1
notes =
skirt_distance = 1
skirt_height = 1
skirts = 1
-small_perimeter_speed = 10
+small_perimeter_speed = 0
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_speed = 0
spiral_vase = 0
standby_temperature_delta = -5
-support_material = 0
+support_material = 1
support_material_angle = 0
-support_material_contact_distance = 0.2
+support_material_contact_distance = 0.3
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
-support_material_interface_layers = 2
+support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
-top_solid_infill_speed = 20
-top_solid_layers = 3
+top_solid_infill_speed = 0
+top_solid_layers = 0
travel_speed = 100
xy_size_compensation = 0
-[print:prusa i3 400 sup]
+[print:prusa i3]
avoid_crossing_perimeters = 0
-bottom_solid_layers = 3
+bottom_solid_layers = 4
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 40
brim_width = 0
complete_objects = 0
-default_acceleration = 0
+default_acceleration = 1000
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
-external_perimeter_speed = 10
+external_perimeter_speed = 30
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
first_layer_extrusion_width = 0
first_layer_height = 0.2
first_layer_speed = 10
-gap_fill_speed = 10
+gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
-infill_extrusion_width = 110%
+infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
-infill_speed = 0
+infill_speed = 80
interface_shells = 0
-layer_height = 0.4
-max_print_speed = 80
+layer_height = 0.2
+max_print_speed = 100
max_volumetric_speed = 0
-min_skirt_length = 1
+min_skirt_length = 3
notes =
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
-perimeter_speed = 0
-perimeters = 2
+perimeter_speed = 60
+perimeters = 3
post_process =
raft_layers = 0
resolution = 0
-seam_position = aligned
-skirt_distance = 1
+seam_position = nearest
+skirt_distance = 6
skirt_height = 1
skirts = 1
-small_perimeter_speed = 10
+small_perimeter_speed = 15
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
-solid_infill_speed = 0
+solid_infill_speed = 60
spiral_vase = 0
standby_temperature_delta = -5
support_material = 1
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
-support_material_interface_layers = 2
+support_material_interface_layers = 3
support_material_interface_spacing = 0
-support_material_interface_speed = 100%
-support_material_pattern = rectilinear
-support_material_spacing = 5
-support_material_speed = 0
-support_material_threshold = 40
+support_material_interface_speed = 75%
+support_material_pattern = pillars
+support_material_spacing = 2.5
+support_material_speed = 60
+support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
-top_solid_infill_speed = 20
-top_solid_layers = 3
+top_solid_infill_speed = 30
+top_solid_layers = 4
travel_speed = 100
xy_size_compensation = 0
-[printer:LULZBOT ABS fine]
+[printer:Lulzbot]
bed_shape = 0x0,298x0,298x275,0x275
before_layer_gcode =
-end_gcode = M104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200 ;\nG28 X0 ; home X axis\nM84 ; disable motors
+end_gcode = M104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200 ;\nG28 X0 ; home X axis\nM84 ; disable motors\n\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\n
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode =
pressure_advance = 0
retract_before_travel = 2
retract_layer_change = 1
-retract_length = 1.75
+retract_length = 3
retract_length_toolchange = 3
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
-retract_speed = 20
-start_gcode = G28 ; home all axes
+retract_speed = 40
+start_gcode = G28 ; home all axes\n
toolchange_gcode =
use_firmware_retraction = 0
use_relative_e_distances = 0
[printer:MendelPro]
bed_shape = 0x0,220x0,220x177,0x177
before_layer_gcode =
-end_gcode = M104 S0 ; turn off temperature\nM140 S0;\nG28 X0 ; home X axis\nM84 ; disable motors\n
+end_gcode = M104 S0 ; turn off temperature\nM140 S0;\nG28 X0 ; home X axis\nG0 Y177;\nM84 ; disable motors\n
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode =
wipe = 0
z_offset = 0
+[printer:Toyrep]
+bed_shape = 0x0,125x0,125x125,0x125
+before_layer_gcode =
+end_gcode = M104 S0 ; turn off nozzle temperature\nM84 ; disable motors
+extruder_offset = 0x0
+gcode_flavor = reprap
+layer_gcode =
+nozzle_diameter = 0.4
+octoprint_apikey =
+octoprint_host =
+pressure_advance = 0
+retract_before_travel = 2
+retract_layer_change = 1
+retract_length = 0
+retract_length_toolchange = 3
+retract_lift = 0
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 10
+start_gcode = \n
+toolchange_gcode =
+use_firmware_retraction = 0
+use_relative_e_distances = 0
+use_volumetric_e = 0
+vibration_limit = 0
+wipe = 0
+z_offset = 0
+
[printer:prusa i3]
-bed_shape = 0x0,190x0,190x190,0x190
+bed_shape = 0x0,190x0,190x220,0x220
before_layer_gcode =
-end_gcode = M104 S0 ; turn off temperature\nM140 S0 ; turn off bed temp \nG28 X0 ; home X axis\nG0 Y190 ; präsent object\nM84 ; disable motors\n\n
+end_gcode = M104 S0 ; turn off temperature\nM140 S0 ; turn off bed temp \nG28 X0 ; home X axis\nG0 Y190 ; präsent object\nM84 ; disable motors\nM81 ; Power off\n\n
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode =
octoprint_host =
pressure_advance = 0
retract_before_travel = 2
-retract_layer_change = 1
-retract_length = 5
+retract_layer_change = 0
+retract_length = 3
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
-start_gcode = G28 Z ; home Z\n\nG28 X Y ; home X Y\n
-toolchange_gcode =
-use_firmware_retraction = 0
+start_gcode = G28 Z ; home Z\n;G0 Z1 ; lift Z\nG28 X Y ; home X Y\nG0 Y40 ; clab move
+toolchange_gcode = M83 ; turn on relative movement for extruder \nG1 E-5 ; retract filament 5mm \nG1 X10 Y10 Z4.000000 ; home X and Y axis leave Z at current height \nM84 E ; release extruder stepper motor from 'holding' position \n@pause ; pause print! \nG1 E0 ; reset extruder, ready to push out plastic again \nM82 ; set extruder movement back to absolute ready for next layer
+use_firmware_retraction = 1
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
projects / stratum0-wiki.git / blobdiff