-# generated by Slic3r 1.2.9 on Tue Nov 1 09:16:29 2016
+# generated by Slic3r 1.2.9 on Mon Nov 21 19:45:57 2016
-[filament:Lulzbot ABS]
-bed_temperature = 100
-bridge_fan_speed = 50
-cooling = 1
-disable_fan_first_layers = 1
-extrusion_multiplier = 1
-fan_always_on = 0
-fan_below_layer_time = 60
-filament_colour = #FFFFFF
-filament_diameter = 2.85
-first_layer_bed_temperature = 100
-first_layer_temperature = 250
-max_fan_speed = 0
-min_fan_speed = 0
-min_print_speed = 5
-slowdown_below_layer_time = 20
-temperature = 230
-
-[filament:Lulzbot PETG ]
-bed_temperature = 75
-bridge_fan_speed = 100
-cooling = 1
-disable_fan_first_layers = 1
-extrusion_multiplier = 1
-fan_always_on = 1
-fan_below_layer_time = 60
-filament_colour = #B1EB96
-filament_diameter = 2.85
-first_layer_bed_temperature = 75
-first_layer_temperature = 235
-max_fan_speed = 100
-min_fan_speed = 50
-min_print_speed = 10
-slowdown_below_layer_time = 30
-temperature = 235
-
-[filament:Lulzbot PLA]
-bed_temperature = 50
-bridge_fan_speed = 100
-cooling = 1
-disable_fan_first_layers = 1
-extrusion_multiplier = 1
-fan_always_on = 1
-fan_below_layer_time = 60
-filament_colour = #C0C0C0
-filament_diameter = 2.86
-first_layer_bed_temperature = 50
-first_layer_temperature = 200
-max_fan_speed = 100
-min_fan_speed = 50
-min_print_speed = 5
-slowdown_below_layer_time = 30
-temperature = 200
-
-[filament:LulzBot PLA DAS FILAMENT]
-bed_temperature = 50
-bridge_fan_speed = 100
-cooling = 1
-disable_fan_first_layers = 1
-extrusion_multiplier = 1
-fan_always_on = 0
-fan_below_layer_time = 60
-filament_colour = #FFFFFF
-filament_diameter = 2.85
-first_layer_bed_temperature = 50
-first_layer_temperature = 220
-max_fan_speed = 100
-min_fan_speed = 30
-min_print_speed = 5
-slowdown_below_layer_time = 30
-temperature = 215
-
-[filament:Lulzbot PLA Weiß]
-bed_temperature = 50
-bridge_fan_speed = 100
-cooling = 1
-disable_fan_first_layers = 1
-extrusion_multiplier = 1
-fan_always_on = 0
-fan_below_layer_time = 60
-filament_colour = #FFFFFF
-filament_diameter = 2.85
-first_layer_bed_temperature = 50
-first_layer_temperature = 200
-max_fan_speed = 100
-min_fan_speed = 30
-min_print_speed = 5
-slowdown_below_layer_time = 30
-temperature = 180
-
-[filament:MendelPro ABS]
+[filament:1.75mm ABS]
bed_temperature = 0
bridge_fan_speed = 50
cooling = 1
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #FFFFFF
-filament_diameter = 1.7
+filament_diameter = 1.75
first_layer_bed_temperature = 0
-first_layer_temperature = 250
+first_layer_temperature = 240
max_fan_speed = 0
min_fan_speed = 0
min_print_speed = 5
slowdown_below_layer_time = 30
temperature = 230
-[filament:MendelPro Holz]
+[filament:1.75mm Holz]
bed_temperature = 50
bridge_fan_speed = 100
cooling = 1
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #FFFFFF
-filament_diameter = 1.7
-first_layer_bed_temperature = 55
+filament_diameter = 1.75
+first_layer_bed_temperature = 50
first_layer_temperature = 200
max_fan_speed = 100
min_fan_speed = 50
min_print_speed = 5
slowdown_below_layer_time = 30
-temperature = 185
+temperature = 190
-[filament:MendelPro PLA]
+[filament:1.75mm PLA]
bed_temperature = 50
bridge_fan_speed = 100
cooling = 1
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #FFFFFF
-filament_diameter = 1.7
+filament_diameter = 1.75
first_layer_bed_temperature = 50
first_layer_temperature = 200
max_fan_speed = 100
min_fan_speed = 50
min_print_speed = 5
slowdown_below_layer_time = 15
-temperature = 180
+temperature = 185
-[filament:TinyBoy PLA]
+[filament:1.75mm PLA TinyBoy]
bed_temperature = 0
bridge_fan_speed = 100
cooling = 1
slowdown_below_layer_time = 15
temperature = 190
-[filament:prusa i3 ABS grün]
+[filament:2.85mm ABS]
bed_temperature = 100
-bridge_fan_speed = 70
+bridge_fan_speed = 50
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 60
-filament_colour = #80FF00
-filament_diameter = 2.9
+filament_colour = #FFFFFF
+filament_diameter = 2.85
first_layer_bed_temperature = 100
-first_layer_temperature = 255
+first_layer_temperature = 250
max_fan_speed = 0
min_fan_speed = 0
min_print_speed = 5
-slowdown_below_layer_time = 15
-temperature = 245
-
-[filament:prusa i3 ABS grün blau]
-bed_temperature = 100
-bridge_fan_speed = 100
-cooling = 1
-disable_fan_first_layers = 1
-extrusion_multiplier = 1
-fan_always_on = 0
-fan_below_layer_time = 60
-filament_colour = #0000A0
-filament_diameter = 2.9
-first_layer_bed_temperature = 100
-first_layer_temperature = 240
-max_fan_speed = 0
-min_fan_speed = 0
-min_print_speed = 10
-slowdown_below_layer_time = 30
-temperature = 235
-
-[filament:prusa i3 PLA grau]
-bed_temperature = 50
-bridge_fan_speed = 100
-cooling = 1
-disable_fan_first_layers = 1
-extrusion_multiplier = 1
-fan_always_on = 1
-fan_below_layer_time = 60
-filament_colour = #808080
-filament_diameter = 2.86
-first_layer_bed_temperature = 50
-first_layer_temperature = 200
-max_fan_speed = 100
-min_fan_speed = 35
-min_print_speed = 10
-slowdown_below_layer_time = 10
-temperature = 185
+slowdown_below_layer_time = 20
+temperature = 230
-[filament:prusa i3 PLA lila]
-bed_temperature = 50
+[filament:2.85mm PETG ]
+bed_temperature = 75
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 60
-filament_colour = #8000FF
-filament_diameter = 3
-first_layer_bed_temperature = 50
-first_layer_temperature = 200
+filament_colour = #B1EB96
+filament_diameter = 2.85
+first_layer_bed_temperature = 75
+first_layer_temperature = 235
max_fan_speed = 100
-min_fan_speed = 35
+min_fan_speed = 50
min_print_speed = 10
-slowdown_below_layer_time = 10
-temperature = 200
+slowdown_below_layer_time = 30
+temperature = 235
-[filament:prusa i3 PLA pink]
+[filament:2.85mm PLA]
bed_temperature = 50
bridge_fan_speed = 100
cooling = 1
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #FF00FF
-filament_diameter = 2.83
+filament_diameter = 2.85
first_layer_bed_temperature = 50
first_layer_temperature = 200
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
slowdown_below_layer_time = 10
-temperature = 180
+temperature = 185
-[filament:prusa i3 Willowflex]
+[filament:2.85mm Willowflex]
bed_temperature = 70
bridge_fan_speed = 100
cooling = 1
filament_colour = #BF0005
filament_diameter = 2.85
first_layer_bed_temperature = 70
-first_layer_temperature = 200
+first_layer_temperature = 160
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
slowdown_below_layer_time = 10
-temperature = 180
+temperature = 160
[presets]
-filament = prusa i3 Willowflex.ini
-print = MendelPro.ini
-printer = Lulzbot.ini
+filament = 2.85mm Willowflex.ini
+print = prusa i3.ini
+printer = prusa i3.ini
[print:Lulzbot]
avoid_crossing_perimeters = 0
bottom_solid_layers = 4
bridge_acceleration = 0
bridge_flow_ratio = 1
-bridge_speed = 40
-brim_width = 0
+bridge_speed = 60
+brim_width = 1
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
-external_perimeter_speed = 20
+external_perimeter_speed = 40
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
layer_height = 0.2
max_print_speed = 100
max_volumetric_speed = 0
-min_skirt_length = 0
+min_skirt_length = 3
notes =
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
-perimeter_speed = 60
-perimeters = 2
+perimeter_speed = 80
+perimeters = 3
post_process =
raft_layers = 0
resolution = 0
seam_position = nearest
-skirt_distance = 5
+skirt_distance = 6
skirt_height = 1
skirts = 1
-small_perimeter_speed = 20
+small_perimeter_speed = 15
solid_infill_below_area = 30
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
-solid_infill_speed = 80
+solid_infill_speed = 60
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
-support_material_contact_distance = 0
+support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
-support_material_interface_layers = 0
+support_material_interface_layers = 3
support_material_interface_spacing = 0
-support_material_interface_speed = 100%
+support_material_interface_speed = 40
support_material_pattern = rectilinear
support_material_spacing = 2.5
-support_material_speed = 40
-support_material_threshold = 45
+support_material_speed = 60
+support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
-top_solid_infill_speed = 20
+top_solid_infill_speed = 40
top_solid_layers = 4
-travel_speed = 100
+travel_speed = 130
xy_size_compensation = 0
[print:MendelPro]
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
-external_perimeter_speed = 20
+external_perimeter_speed = 30
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
travel_speed = 100
xy_size_compensation = 0
-[print:prusa i3 200]
-avoid_crossing_perimeters = 1
+[print:prusa i3]
+avoid_crossing_perimeters = 0
bottom_solid_layers = 4
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 40
-brim_width = 1
+brim_width = 0
complete_objects = 0
-default_acceleration = 0
+default_acceleration = 1000
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
-external_perimeter_speed = 20
+external_perimeter_speed = 30
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
first_layer_acceleration = 0
first_layer_extrusion_width = 0
first_layer_height = 0.2
-first_layer_speed = 15
+first_layer_speed = 10
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
-infill_speed = 0
+infill_speed = 80
interface_shells = 0
layer_height = 0.2
-max_print_speed = 50
+max_print_speed = 100
max_volumetric_speed = 0
min_skirt_length = 3
notes =
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
-perimeter_speed = 40
+perimeter_speed = 60
perimeters = 3
post_process =
raft_layers = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
-solid_infill_speed = 0
+solid_infill_speed = 60
spiral_vase = 0
standby_temperature_delta = -5
-support_material = 0
+support_material = 1
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
-support_material_interface_speed = 10
+support_material_interface_speed = 75%
support_material_pattern = pillars
support_material_spacing = 2.5
-support_material_speed = 40
-support_material_threshold = 40
+support_material_speed = 60
+support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
-top_solid_infill_speed = 20
+top_solid_infill_speed = 30
top_solid_layers = 4
travel_speed = 100
xy_size_compensation = 0
-[print:prusa i3 vase]
-avoid_crossing_perimeters = 0
-bottom_solid_layers = 0
-bridge_acceleration = 0
-bridge_flow_ratio = 1
-bridge_speed = 40
-brim_width = 1
-complete_objects = 0
-default_acceleration = 0
-dont_support_bridges = 1
-external_fill_pattern = rectilinear
-external_perimeter_extrusion_width = 0
-external_perimeter_speed = 20
-external_perimeters_first = 0
-extra_perimeters = 1
-extruder_clearance_height = 20
-extruder_clearance_radius = 20
-extrusion_width = 0
-fill_angle = 45
-fill_density = 0%
-fill_pattern = rectilinear
-first_layer_acceleration = 0
-first_layer_extrusion_width = 0
-first_layer_height = 0.2
-first_layer_speed = 15
-gap_fill_speed = 20
-gcode_comments = 0
-infill_acceleration = 0
-infill_every_layers = 1
-infill_extruder = 1
-infill_extrusion_width = 0
-infill_first = 1
-infill_only_where_needed = 0
-infill_overlap = 15%
-infill_speed = 60
-interface_shells = 0
-layer_height = 0.2
-max_print_speed = 65
-max_volumetric_speed = 0
-min_skirt_length = 1
-notes =
-only_retract_when_crossing_perimeters = 1
-ooze_prevention = 0
-output_filename_format = [input_filename_base].gcode
-overhangs = 1
-perimeter_acceleration = 0
-perimeter_extruder = 1
-perimeter_extrusion_width = 0
-perimeter_speed = 40
-perimeters = 1
-post_process =
-raft_layers = 0
-resolution = 0
-seam_position = nearest
-skirt_distance = 1
-skirt_height = 1
-skirts = 1
-small_perimeter_speed = 20
-solid_infill_below_area = 70
-solid_infill_every_layers = 0
-solid_infill_extruder = 1
-solid_infill_extrusion_width = 0
-solid_infill_speed = 60
-spiral_vase = 1
-standby_temperature_delta = -5
-support_material = 0
-support_material_angle = 0
-support_material_contact_distance = 0.2
-support_material_enforce_layers = 0
-support_material_extruder = 1
-support_material_extrusion_width = 0
-support_material_interface_extruder = 1
-support_material_interface_layers = 3
-support_material_interface_spacing = 0
-support_material_interface_speed = 10
-support_material_pattern = pillars
-support_material_spacing = 2.5
-support_material_speed = 40
-support_material_threshold = 40
-thin_walls = 1
-threads = 2
-top_infill_extrusion_width = 0
-top_solid_infill_speed = 20
-top_solid_layers = 0
-travel_speed = 100
-xy_size_compensation = 0
-
[printer:Lulzbot]
bed_shape = 0x0,298x0,298x275,0x275
before_layer_gcode =
projects / stratum0-wiki.git / blobdiff