/* OpenStreetMap */ Termine

[stratum0-wiki.git] / 3D-Drucker%2FSlicerBundle.ini.mw

diff --git a/3D-Drucker%2FSlicerBundle.ini.mw b/3D-Drucker%2FSlicerBundle.ini.mw
index 89f4e03..bca5b64 100644 (file)
--- a/3D-Drucker%2FSlicerBundle.ini.mw
+++ b/3D-Drucker%2FSlicerBundle.ini.mw
@@ -1,8 +1,8 @@
-# generated by Slic3r 1.2.9 on Mon Nov 21 19:45:57 2016
+# generated by Slic3r 1.2.9 on Mon Jan 30 16:49:14 2017

 
 [filament:1.75mm ABS]
 bed_temperature = 0
 
 [filament:1.75mm ABS]
 bed_temperature = 0

-bridge_fan_speed = 50
+bridge_fan_speed = 35

 cooling = 1
 disable_fan_first_layers = 1
 extrusion_multiplier = 1
 cooling = 1
 disable_fan_first_layers = 1
 extrusion_multiplier = 1


@@ -11,11 +11,11 @@ fan_below_layer_time = 60
 filament_colour = #FFFFFF
 filament_diameter = 1.75
 first_layer_bed_temperature = 0
 filament_colour = #FFFFFF
 filament_diameter = 1.75
 first_layer_bed_temperature = 0

-first_layer_temperature = 240
+first_layer_temperature = 250

 max_fan_speed = 0
 min_fan_speed = 0
 min_print_speed = 5
 max_fan_speed = 0
 min_fan_speed = 0
 min_print_speed = 5

-slowdown_below_layer_time = 30
+slowdown_below_layer_time = 10

 temperature = 230
 
 [filament:1.75mm Holz]
 temperature = 230
 
 [filament:1.75mm Holz]


@@ -33,26 +33,26 @@ first_layer_temperature = 200
 max_fan_speed = 100
 min_fan_speed = 50
 min_print_speed = 5
 max_fan_speed = 100
 min_fan_speed = 50
 min_print_speed = 5

-slowdown_below_layer_time = 30
+slowdown_below_layer_time = 10

 temperature = 190
 
 [filament:1.75mm PLA]
 bed_temperature = 50
 bridge_fan_speed = 100
 cooling = 1
 temperature = 190
 
 [filament:1.75mm PLA]
 bed_temperature = 50
 bridge_fan_speed = 100
 cooling = 1

-disable_fan_first_layers = 1
+disable_fan_first_layers = 3

 extrusion_multiplier = 1
 extrusion_multiplier = 1

-fan_always_on = 1
+fan_always_on = 0

 fan_below_layer_time = 60
 filament_colour = #FFFFFF
 filament_diameter = 1.75
 first_layer_bed_temperature = 50
 fan_below_layer_time = 60
 filament_colour = #FFFFFF
 filament_diameter = 1.75
 first_layer_bed_temperature = 50

-first_layer_temperature = 200
+first_layer_temperature = 220

 max_fan_speed = 100
 max_fan_speed = 100

-min_fan_speed = 50
+min_fan_speed = 100

 min_print_speed = 5
 min_print_speed = 5

-slowdown_below_layer_time = 15
-temperature = 185
+slowdown_below_layer_time = 20
+temperature = 190

 
 [filament:1.75mm PLA TinyBoy]
 bed_temperature = 0
 
 [filament:1.75mm PLA TinyBoy]
 bed_temperature = 0


@@ -69,12 +69,48 @@ first_layer_temperature = 200
 max_fan_speed = 40
 min_fan_speed = 35
 min_print_speed = 5
 max_fan_speed = 40
 min_fan_speed = 35
 min_print_speed = 5

-slowdown_below_layer_time = 15
-temperature = 190
+slowdown_below_layer_time = 10
+temperature = 200
+
+[filament:2.70mm PLA]
+bed_temperature = 60
+bridge_fan_speed = 100
+cooling = 1
+disable_fan_first_layers = 3
+extrusion_multiplier = 1
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_colour = #FF00FF
+filament_diameter = 2.72
+first_layer_bed_temperature = 60
+first_layer_temperature = 220
+max_fan_speed = 100
+min_fan_speed = 100
+min_print_speed = 5
+slowdown_below_layer_time = 20
+temperature = 200
+
+[filament:2.80mm PETG ]
+bed_temperature = 75
+bridge_fan_speed = 100
+cooling = 1
+disable_fan_first_layers = 3
+extrusion_multiplier = 1
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_colour = #B1EB96
+filament_diameter = 2.8
+first_layer_bed_temperature = 75
+first_layer_temperature = 245
+max_fan_speed = 100
+min_fan_speed = 100
+min_print_speed = 5
+slowdown_below_layer_time = 10
+temperature = 235

 
 [filament:2.85mm ABS]
 bed_temperature = 100
 
 [filament:2.85mm ABS]
 bed_temperature = 100

-bridge_fan_speed = 50
+bridge_fan_speed = 35

 cooling = 1
 disable_fan_first_layers = 1
 extrusion_multiplier = 1
 cooling = 1
 disable_fan_first_layers = 1
 extrusion_multiplier = 1


@@ -87,29 +123,47 @@ first_layer_temperature = 250
 max_fan_speed = 0
 min_fan_speed = 0
 min_print_speed = 5
 max_fan_speed = 0
 min_fan_speed = 0
 min_print_speed = 5

-slowdown_below_layer_time = 20
-temperature = 230
+slowdown_below_layer_time = 10
+temperature = 235

 
 [filament:2.85mm PETG ]
 bed_temperature = 75
 bridge_fan_speed = 100
 cooling = 1
 
 [filament:2.85mm PETG ]
 bed_temperature = 75
 bridge_fan_speed = 100
 cooling = 1

-disable_fan_first_layers = 1
+disable_fan_first_layers = 3

 extrusion_multiplier = 1
 fan_always_on = 1
 fan_below_layer_time = 60
 filament_colour = #B1EB96
 filament_diameter = 2.85
 first_layer_bed_temperature = 75
 extrusion_multiplier = 1
 fan_always_on = 1
 fan_below_layer_time = 60
 filament_colour = #B1EB96
 filament_diameter = 2.85
 first_layer_bed_temperature = 75

-first_layer_temperature = 235
+first_layer_temperature = 245

 max_fan_speed = 100
 max_fan_speed = 100

-min_fan_speed = 50
-min_print_speed = 10
-slowdown_below_layer_time = 30
+min_fan_speed = 100
+min_print_speed = 5
+slowdown_below_layer_time = 10

 temperature = 235
 
 [filament:2.85mm PLA]
 temperature = 235
 
 [filament:2.85mm PLA]

-bed_temperature = 50
+bed_temperature = 60
+bridge_fan_speed = 100
+cooling = 1
+disable_fan_first_layers = 3
+extrusion_multiplier = 1
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_colour = #FF00FF
+filament_diameter = 2.85
+first_layer_bed_temperature = 60
+first_layer_temperature = 220
+max_fan_speed = 100
+min_fan_speed = 100
+min_print_speed = 5
+slowdown_below_layer_time = 20
+temperature = 195
+
+[filament:2.85mm PLA hot]
+bed_temperature = 60

 bridge_fan_speed = 100
 cooling = 1
 disable_fan_first_layers = 1
 bridge_fan_speed = 100
 cooling = 1
 disable_fan_first_layers = 1


@@ -118,13 +172,13 @@ fan_always_on = 1
 fan_below_layer_time = 60
 filament_colour = #FF00FF
 filament_diameter = 2.85
 fan_below_layer_time = 60
 filament_colour = #FF00FF
 filament_diameter = 2.85

-first_layer_bed_temperature = 50
-first_layer_temperature = 200
+first_layer_bed_temperature = 60
+first_layer_temperature = 215

 max_fan_speed = 100
 max_fan_speed = 100

-min_fan_speed = 35
-min_print_speed = 10
+min_fan_speed = 100
+min_print_speed = 5

 slowdown_below_layer_time = 10
 slowdown_below_layer_time = 10

-temperature = 185
+temperature = 215

 
 [filament:2.85mm Willowflex]
 bed_temperature = 70
 
 [filament:2.85mm Willowflex]
 bed_temperature = 70


@@ -139,15 +193,15 @@ filament_diameter = 2.85
 first_layer_bed_temperature = 70
 first_layer_temperature = 160
 max_fan_speed = 100
 first_layer_bed_temperature = 70
 first_layer_temperature = 160
 max_fan_speed = 100

-min_fan_speed = 35
-min_print_speed = 10
-slowdown_below_layer_time = 10
+min_fan_speed = 50
+min_print_speed = 5
+slowdown_below_layer_time = 20

 temperature = 160
 
 [presets]
 temperature = 160
 
 [presets]

-filament = 2.85mm Willowflex.ini
-print = prusa i3.ini
-printer = prusa i3.ini
+filament = 2.80mm PETG .ini
+print = Lulzbot.ini
+printer = MendelPro.ini

 
 [print:Lulzbot]
 avoid_crossing_perimeters = 0
 
 [print:Lulzbot]
 avoid_crossing_perimeters = 0


@@ -155,40 +209,40 @@ bottom_solid_layers = 4
 bridge_acceleration = 0
 bridge_flow_ratio = 1
 bridge_speed = 60
 bridge_acceleration = 0
 bridge_flow_ratio = 1
 bridge_speed = 60

-brim_width = 1
+brim_width = 2

 complete_objects = 0
 default_acceleration = 0
 dont_support_bridges = 1
 external_fill_pattern = rectilinear
 external_perimeter_extrusion_width = 0
 complete_objects = 0
 default_acceleration = 0
 dont_support_bridges = 1
 external_fill_pattern = rectilinear
 external_perimeter_extrusion_width = 0

-external_perimeter_speed = 40
+external_perimeter_speed = 30

 external_perimeters_first = 0
 extra_perimeters = 1
 extruder_clearance_height = 20
 extruder_clearance_radius = 20
 extrusion_width = 0
 external_perimeters_first = 0
 extra_perimeters = 1
 extruder_clearance_height = 20
 extruder_clearance_radius = 20
 extrusion_width = 0

-fill_angle = 35
+fill_angle = 45

 fill_density = 20%
 fill_pattern = rectilinear
 first_layer_acceleration = 0
 first_layer_extrusion_width = 0
 first_layer_height = 0.2
 fill_density = 20%
 fill_pattern = rectilinear
 first_layer_acceleration = 0
 first_layer_extrusion_width = 0
 first_layer_height = 0.2

-first_layer_speed = 10
+first_layer_speed = 20

 gap_fill_speed = 20
 gcode_comments = 0
 infill_acceleration = 0
 infill_every_layers = 1
 infill_extruder = 1
 gap_fill_speed = 20
 gcode_comments = 0
 infill_acceleration = 0
 infill_every_layers = 1
 infill_extruder = 1

-infill_extrusion_width = 0
+infill_extrusion_width = 1.1

 infill_first = 0
 infill_only_where_needed = 0
 infill_overlap = 15%
 infill_first = 0
 infill_only_where_needed = 0
 infill_overlap = 15%

-infill_speed = 80
+infill_speed = 60

 interface_shells = 0
 layer_height = 0.2
 interface_shells = 0
 layer_height = 0.2

-max_print_speed = 100
+max_print_speed = 130

 max_volumetric_speed = 0
 max_volumetric_speed = 0

-min_skirt_length = 3
+min_skirt_length = 1

 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0


@@ -197,52 +251,52 @@ overhangs = 1
 perimeter_acceleration = 0
 perimeter_extruder = 1
 perimeter_extrusion_width = 0
 perimeter_acceleration = 0
 perimeter_extruder = 1
 perimeter_extrusion_width = 0

-perimeter_speed = 80
+perimeter_speed = 60

 perimeters = 3
 post_process = 
 raft_layers = 0
 resolution = 0
 perimeters = 3
 post_process = 
 raft_layers = 0
 resolution = 0

-seam_position = nearest
+seam_position = aligned

 skirt_distance = 6
 skirt_height = 1
 skirts = 1
 small_perimeter_speed = 15
 skirt_distance = 6
 skirt_height = 1
 skirts = 1
 small_perimeter_speed = 15

-solid_infill_below_area = 30
+solid_infill_below_area = 70

 solid_infill_every_layers = 0
 solid_infill_extruder = 1
 solid_infill_extrusion_width = 0
 solid_infill_every_layers = 0
 solid_infill_extruder = 1
 solid_infill_extrusion_width = 0

-solid_infill_speed = 60
+solid_infill_speed = 10

 spiral_vase = 0
 standby_temperature_delta = -5
 spiral_vase = 0
 standby_temperature_delta = -5

-support_material = 0
+support_material = 1

 support_material_angle = 0
 support_material_angle = 0

-support_material_contact_distance = 0.2
+support_material_contact_distance = 0.4

 support_material_enforce_layers = 0
 support_material_extruder = 1
 support_material_extrusion_width = 0
 support_material_interface_extruder = 1
 support_material_interface_layers = 3
 support_material_interface_spacing = 0
 support_material_enforce_layers = 0
 support_material_extruder = 1
 support_material_extrusion_width = 0
 support_material_interface_extruder = 1
 support_material_interface_layers = 3
 support_material_interface_spacing = 0

-support_material_interface_speed = 40
-support_material_pattern = rectilinear
-support_material_spacing = 2.5
+support_material_interface_speed = 30
+support_material_pattern = rectilinear-grid
+support_material_spacing = 2

 support_material_speed = 60
 support_material_threshold = 0
 support_material_speed = 60
 support_material_threshold = 0

-thin_walls = 1
+thin_walls = 0

 threads = 2
 top_infill_extrusion_width = 0
 threads = 2
 top_infill_extrusion_width = 0

-top_solid_infill_speed = 40
-top_solid_layers = 4
+top_solid_infill_speed = 5
+top_solid_layers = 5

 travel_speed = 130
 xy_size_compensation = 0
 
 [print:MendelPro]
 travel_speed = 130
 xy_size_compensation = 0
 
 [print:MendelPro]

-avoid_crossing_perimeters = 0
-bottom_solid_layers = 4
+avoid_crossing_perimeters = 1
+bottom_solid_layers = 5

 bridge_acceleration = 0
 bridge_flow_ratio = 1
 bridge_speed = 40
 bridge_acceleration = 0
 bridge_flow_ratio = 1
 bridge_speed = 40

-brim_width = 1
+brim_width = 2

 complete_objects = 0
 default_acceleration = 0
 dont_support_bridges = 1
 complete_objects = 0
 default_acceleration = 0
 dont_support_bridges = 1


@@ -260,8 +314,8 @@ fill_pattern = rectilinear
 first_layer_acceleration = 0
 first_layer_extrusion_width = 0
 first_layer_height = 0.2
 first_layer_acceleration = 0
 first_layer_extrusion_width = 0
 first_layer_height = 0.2

-first_layer_speed = 10
-gap_fill_speed = 10
+first_layer_speed = 30
+gap_fill_speed = 20

 gcode_comments = 0
 infill_acceleration = 0
 infill_every_layers = 1
 gcode_comments = 0
 infill_acceleration = 0
 infill_every_layers = 1


@@ -269,13 +323,13 @@ infill_extruder = 1
 infill_extrusion_width = 0
 infill_first = 0
 infill_only_where_needed = 0
 infill_extrusion_width = 0
 infill_first = 0
 infill_only_where_needed = 0

-infill_overlap = 15%
-infill_speed = 0
+infill_overlap = 25%
+infill_speed = 50

 interface_shells = 0
 layer_height = 0.2
 max_print_speed = 80
 max_volumetric_speed = 0
 interface_shells = 0
 layer_height = 0.2
 max_print_speed = 80
 max_volumetric_speed = 0

-min_skirt_length = 2
+min_skirt_length = 6

 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0


@@ -284,21 +338,21 @@ overhangs = 1
 perimeter_acceleration = 0
 perimeter_extruder = 1
 perimeter_extrusion_width = 0
 perimeter_acceleration = 0
 perimeter_extruder = 1
 perimeter_extrusion_width = 0

-perimeter_speed = 0
-perimeters = 2
+perimeter_speed = 50
+perimeters = 3

 post_process = 
 raft_layers = 0
 resolution = 0
 seam_position = nearest
 post_process = 
 raft_layers = 0
 resolution = 0
 seam_position = nearest

-skirt_distance = 10
+skirt_distance = 6

 skirt_height = 1
 skirts = 1
 skirt_height = 1
 skirts = 1

-small_perimeter_speed = 10
+small_perimeter_speed = 20

 solid_infill_below_area = 70
 solid_infill_every_layers = 0
 solid_infill_extruder = 1
 solid_infill_extrusion_width = 0
 solid_infill_below_area = 70
 solid_infill_every_layers = 0
 solid_infill_extruder = 1
 solid_infill_extrusion_width = 0

-solid_infill_speed = 0
+solid_infill_speed = 40

 spiral_vase = 0
 standby_temperature_delta = -5
 support_material = 1
 spiral_vase = 0
 standby_temperature_delta = -5
 support_material = 1


@@ -310,16 +364,16 @@ support_material_extrusion_width = 0
 support_material_interface_extruder = 1
 support_material_interface_layers = 3
 support_material_interface_spacing = 0
 support_material_interface_extruder = 1
 support_material_interface_layers = 3
 support_material_interface_spacing = 0

-support_material_interface_speed = 100%
-support_material_pattern = pillars
+support_material_interface_speed = 40
+support_material_pattern = rectilinear

 support_material_spacing = 3
 support_material_spacing = 3

-support_material_speed = 60
+support_material_speed = 50

 support_material_threshold = 0
 thin_walls = 1
 threads = 2
 top_infill_extrusion_width = 0
 support_material_threshold = 0
 thin_walls = 1
 threads = 2
 top_infill_extrusion_width = 0

-top_solid_infill_speed = 20
-top_solid_layers = 4
+top_solid_infill_speed = 40
+top_solid_layers = 5

 travel_speed = 100
 xy_size_compensation = 0
 
 travel_speed = 100
 xy_size_compensation = 0
 


@@ -505,7 +559,7 @@ bridge_flow_ratio = 1
 bridge_speed = 40
 brim_width = 0
 complete_objects = 0
 bridge_speed = 40
 brim_width = 0
 complete_objects = 0

-default_acceleration = 1000
+default_acceleration = 0

 dont_support_bridges = 1
 external_fill_pattern = rectilinear
 external_perimeter_extrusion_width = 0
 dont_support_bridges = 1
 external_fill_pattern = rectilinear
 external_perimeter_extrusion_width = 0


@@ -517,7 +571,94 @@ extruder_clearance_radius = 20
 extrusion_width = 0
 fill_angle = 45
 fill_density = 20%
 extrusion_width = 0
 fill_angle = 45
 fill_density = 20%

-fill_pattern = rectilinear
+fill_pattern = honeycomb
+first_layer_acceleration = 0
+first_layer_extrusion_width = 0
+first_layer_height = 0.3
+first_layer_speed = 10
+gap_fill_speed = 20
+gcode_comments = 0
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap = 15%
+infill_speed = 80
+interface_shells = 0
+layer_height = 0.15
+max_print_speed = 100
+max_volumetric_speed = 0
+min_skirt_length = 3
+notes = 
+only_retract_when_crossing_perimeters = 1
+ooze_prevention = 0
+output_filename_format = [input_filename_base].gcode
+overhangs = 1
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 60
+perimeters = 3
+post_process = 
+raft_layers = 0
+resolution = 0
+seam_position = nearest
+skirt_distance = 6
+skirt_height = 1
+skirts = 1
+small_perimeter_speed = 15
+solid_infill_below_area = 70
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 0
+solid_infill_speed = 40
+spiral_vase = 0
+standby_temperature_delta = -5
+support_material = 1
+support_material_angle = 0
+support_material_contact_distance = 0.3
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_extruder = 1
+support_material_interface_layers = 3
+support_material_interface_spacing = 0
+support_material_interface_speed = 40
+support_material_pattern = rectilinear
+support_material_spacing = 3
+support_material_speed = 40
+support_material_threshold = 0
+thin_walls = 1
+threads = 2
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 30
+top_solid_layers = 4
+travel_speed = 100
+xy_size_compensation = 0
+
+[print:prusa i3 test]
+avoid_crossing_perimeters = 0
+bottom_solid_layers = 4
+bridge_acceleration = 0
+bridge_flow_ratio = 1
+bridge_speed = 40
+brim_width = 5
+complete_objects = 0
+default_acceleration = 0
+dont_support_bridges = 1
+external_fill_pattern = rectilinear
+external_perimeter_extrusion_width = 0
+external_perimeter_speed = 30
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extrusion_width = 0
+fill_angle = 45
+fill_density = 20%
+fill_pattern = honeycomb

 first_layer_acceleration = 0
 first_layer_extrusion_width = 0
 first_layer_height = 0.2
 first_layer_acceleration = 0
 first_layer_extrusion_width = 0
 first_layer_height = 0.2


@@ -559,22 +700,22 @@ solid_infill_below_area = 70
 solid_infill_every_layers = 0
 solid_infill_extruder = 1
 solid_infill_extrusion_width = 0
 solid_infill_every_layers = 0
 solid_infill_extruder = 1
 solid_infill_extrusion_width = 0

-solid_infill_speed = 60
+solid_infill_speed = 40

 spiral_vase = 0
 standby_temperature_delta = -5
 support_material = 1
 support_material_angle = 0
 spiral_vase = 0
 standby_temperature_delta = -5
 support_material = 1
 support_material_angle = 0

-support_material_contact_distance = 0.2
+support_material_contact_distance = 0

 support_material_enforce_layers = 0
 support_material_extruder = 1
 support_material_extrusion_width = 0
 support_material_interface_extruder = 1
 support_material_interface_layers = 3
 support_material_interface_spacing = 0
 support_material_enforce_layers = 0
 support_material_extruder = 1
 support_material_extrusion_width = 0
 support_material_interface_extruder = 1
 support_material_interface_layers = 3
 support_material_interface_spacing = 0

-support_material_interface_speed = 75%
+support_material_interface_speed = 40

 support_material_pattern = pillars
 support_material_pattern = pillars

-support_material_spacing = 2.5
-support_material_speed = 60
+support_material_spacing = 3
+support_material_speed = 40

 support_material_threshold = 0
 thin_walls = 1
 threads = 2
 support_material_threshold = 0
 thin_walls = 1
 threads = 2


@@ -587,7 +728,7 @@ xy_size_compensation = 0
 [printer:Lulzbot]
 bed_shape = 0x0,298x0,298x275,0x275
 before_layer_gcode = 
 [printer:Lulzbot]
 bed_shape = 0x0,298x0,298x275,0x275
 before_layer_gcode = 

-end_gcode = M104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200 ;\nG28 X0 ; home X axis\nM84 ; disable motors\n\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\n
+end_gcode = M104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200 ;\nG28 X0 ; home X axis\nM84 ; disable motors\n\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\n

 extruder_offset = 0x0
 gcode_flavor = reprap
 layer_gcode = 
 extruder_offset = 0x0
 gcode_flavor = reprap
 layer_gcode = 


@@ -631,7 +772,7 @@ retract_lift = 0
 retract_restart_extra = 0
 retract_restart_extra_toolchange = 0
 retract_speed = 40
 retract_restart_extra = 0
 retract_restart_extra_toolchange = 0
 retract_speed = 40

-start_gcode = G28 Z            ; home Z\nG28 X Y         ; home X Y\n
+start_gcode = G28 Z            ; home Z\nG28 X Y         ; home X Y\nG0   Y40        ; clab move\n

 toolchange_gcode = 
 use_firmware_retraction = 0
 use_relative_e_distances = 0
 toolchange_gcode = 
 use_firmware_retraction = 0
 use_relative_e_distances = 0


@@ -709,15 +850,15 @@ octoprint_host =
 pressure_advance = 0
 retract_before_travel = 2
 retract_layer_change = 0
 pressure_advance = 0
 retract_before_travel = 2
 retract_layer_change = 0

-retract_length = 3
+retract_length = 2

 retract_length_toolchange = 10
 retract_lift = 0
 retract_restart_extra = 0
 retract_restart_extra_toolchange = 0
 retract_speed = 40
 retract_length_toolchange = 10
 retract_lift = 0
 retract_restart_extra = 0
 retract_restart_extra_toolchange = 0
 retract_speed = 40

-start_gcode = G28 Z            ; home Z\n;G0 Z1            ; lift Z\nG28 X Y         ; home X Y\nG0         Y40 ; clab move
+start_gcode = G28 Z             ; home Z\n;G0 Z1            ; lift Z\nG28 X Y         ; home X Y\nG0   Y40        ; clab move

 toolchange_gcode = M83 ; turn on relative movement for extruder  \nG1 E-5  ; retract filament 5mm  \nG1 X10 Y10 Z4.000000  ; home X and Y axis leave Z at current height  \nM84 E ; release extruder stepper motor from 'holding' position  \n@pause ; pause print!  \nG1 E0 ; reset extruder, ready to push out plastic again  \nM82 ; set extruder movement back to absolute ready for next layer  
 toolchange_gcode = M83 ; turn on relative movement for extruder  \nG1 E-5  ; retract filament 5mm  \nG1 X10 Y10 Z4.000000  ; home X and Y axis leave Z at current height  \nM84 E ; release extruder stepper motor from 'holding' position  \n@pause ; pause print!  \nG1 E0 ; reset extruder, ready to push out plastic again  \nM82 ; set extruder movement back to absolute ready for next layer  

-use_firmware_retraction = 1
+use_firmware_retraction = 0

 use_relative_e_distances = 0
 use_volumetric_e = 0
 vibration_limit = 0
 use_relative_e_distances = 0
 use_volumetric_e = 0
 vibration_limit = 0