-Eine Seite um (gute) Beispielkonfigkurationen zu sammeln, am besten mit Beispieldruck(foto)
+Eine Seite um (gute) Beispielkonfigkurationen zu sammeln, am besten mit Beispieldruck (Foto)
-== Gelbes Filament ==
+Es gibt vermutlich nicht ''die eine Ideal-Konfiguration'' die für alle Teile gut funktioniert, mit den hier gelisteten sollte aber ein Druck einigermaßen gelingen.
+
+=== aktuelle configs ===
+Der Drucker hat sich verändert, dementsprechend haben sich auch die configs geändert.
+Beispielsweise haben wir jetzt 0.5 mm Düsen an den beiden Hot Ends, nicht mehr 0.35 mm.
+Dazu kommt, dass das homing konstruktionsbedingt außerhalb des hot beds stattfindet, mit diesem Start-gcode wird das ausgeglichen:
+ G28 X0 Y0 ; home X and Y
+ G0 X60; move to X60
+ G92 X0; set postition to X=0
+ G28 Z0; home Z
+Das, oder etwas Ähnliches sollte in allen configs mit drin sein.
+
+Eine funktionierende, aber noch nicht sehr fein justierte config ist diese:
+==== larsan ====
+<pre style="height:200px;overflow-y:scroll;">
+# generated by Slic3r 0.9.10 on Sun Sep 29 22:51:39 2013
+avoid_crossing_perimeters = 0
+bed_size = 190,190
+bed_temperature = 50
+bottom_solid_layers = 3
+bridge_acceleration = 0
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 60
+brim_width = 0
+complete_objects = 1
+cooling = 1
+default_acceleration = 0
+disable_fan_first_layers = 1
+duplicate = 1
+duplicate_distance = 6
+duplicate_grid = 1,1
+end_gcode = M104 S0 ; turn off extruder temperature\n;M140 S0 ; turn off bed temperature; currently disabled\nG0 X0 ; move X axis to 0\nG92 Z0 E5 ;define current point as Z0 E5\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y198 F6000 ; drive print table all the way out\nM84 ; disable motors
+external_perimeter_speed = 70%
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 1
+extruder_clearance_radius = 30
+extruder_offset = 0x0
+extrusion_axis = E
+extrusion_multiplier = 1
+extrusion_width = 180%
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_diameter = 1.75
+fill_angle = 45
+fill_density = 0.3
+fill_pattern = honeycomb
+first_layer_bed_temperature = 50
+first_layer_extrusion_width = 0
+first_layer_height = 0.25
+first_layer_speed = 30%
+first_layer_temperature = 200
+g0 = 0
+gap_fill_speed = 15
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor = reprap
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_only_where_needed = 0
+infill_speed = 60
+layer_gcode =
+layer_height = 0.25
+max_fan_speed = 100
+min_fan_speed = 35
+min_print_speed = 5
+min_skirt_length = 0
+notes = larsanconfig
+nozzle_diameter = 0.5
+only_retract_when_crossing_perimeters = 1
+output_filename_format = [input_filename_base].gcode
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 80
+perimeters = 3
+post_process =
+print_center = 90,60
+raft_layers = 0
+randomize_start = 0
+resolution = 0
+retract_before_travel = 2
+retract_layer_change = 1
+retract_length = 2
+retract_length_toolchange = 10
+retract_lift = 0
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 35
+rotate = 0
+scale = 1
+skirt_distance = 10
+skirt_height = 1
+skirts = 3
+slowdown_below_layer_time = 30
+small_perimeter_speed = 50
+solid_fill_pattern = rectilinear
+solid_infill_below_area = 40
+solid_infill_every_layers = 0
+solid_infill_extrusion_width = 0
+solid_infill_speed = 80
+spiral_vase = 0
+start_gcode = G28 X0 Y0 ; home X and Y\nG0 X60; move to X60\nG92 X0; set postition to X=0\nG28 Z0; home Z
+support_material = 0
+support_material_angle = 0
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_layers = 0
+support_material_interface_spacing = 0
+support_material_pattern = rectilinear
+support_material_spacing = 2.5
+support_material_speed = 65
+support_material_threshold = 0
+temperature = 195
+threads = 1
+toolchange_gcode =
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 60
+top_solid_layers = 3
+travel_speed = 80
+use_relative_e_distances = 0
+vibration_limit = 0
+wipe = 0
+z_offset = 0
+</pre>
+
+==== Kasalehlia ====
+etwas auf den neuen Drucker angepasst. Start G-Code und neuer Lüfter am Druckkopf sind berücksichtigt.
+
+Printer:
+<pre style="height:200px;overflow-y:scroll;">
+bed_size = 200,200
+end_gcode = M107; fan off\nM104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors
+extruder_offset = 0x0
+gcode_flavor = reprap
+layer_gcode =
+nozzle_diameter = 0.5
+print_center = 100,80
+retract_before_travel = 2
+retract_layer_change = 1
+retract_length = 1
+retract_length_toolchange = 10
+retract_lift = 0
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 30
+start_gcode = G28 X0 Y0 ; home X and Y\nG0 X60; move to X60\nG92 X0; set postition to X=0\nG28 Z0; home Z\nM106; fan on
+toolchange_gcode =
+use_firmware_retraction = 0
+use_relative_e_distances = 0
+vibration_limit = 0
+wipe = 0
+z_offset = 0
+</pre>
+
+Normales PLA:
+<pre style="height:200px;overflow-y:scroll;">
+bed_temperature = 50
+bridge_fan_speed = 100
+cooling = 1
+disable_fan_first_layers = 1
+extrusion_multiplier = 1
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_diameter = 1.75
+first_layer_bed_temperature = 55
+first_layer_temperature = 200
+max_fan_speed = 100
+min_fan_speed = 35
+min_print_speed = 10
+slowdown_below_layer_time = 30
+temperature = 195
+</pre>
+
+Holz PLA:
+<pre style="height:200px;overflow-y:scroll;">
+bed_temperature = 50
+bridge_fan_speed = 100
+cooling = 1
+disable_fan_first_layers = 1
+extrusion_multiplier = 1
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_diameter = 1.75
+first_layer_bed_temperature = 55
+first_layer_temperature = 210
+max_fan_speed = 100
+min_fan_speed = 35
+min_print_speed = 10
+slowdown_below_layer_time = 30
+temperature = 210
+</pre>
+
+Matetags oder andere Filigranere Dinge:
+<pre style="height:200px;overflow-y:scroll;">
+avoid_crossing_perimeters = 0
+bottom_solid_layers = 3
+bridge_acceleration = 0
+bridge_flow_ratio = 1
+bridge_speed = 60
+brim_width = 3
+complete_objects = 0
+default_acceleration = 0
+external_perimeter_speed = 70%
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extrusion_width = 0
+fill_angle = 45
+fill_density = 1
+fill_pattern = rectilinear
+first_layer_acceleration = 0
+first_layer_extrusion_width = 200%
+first_layer_height = 0.22
+first_layer_speed = 30%
+gap_fill_speed = 20
+gcode_comments = 0
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_only_where_needed = 0
+infill_speed = 60
+layer_height = 0.22
+min_skirt_length = 0
+notes =
+only_retract_when_crossing_perimeters = 1
+ooze_prevention = 0
+output_filename_format = [input_filename_base].gcode
+overhangs = 1
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 50
+perimeters = 3
+post_process =
+raft_layers = 0
+randomize_start = 0
+resolution = 0
+skirt_distance = 6
+skirt_height = 1
+skirts = 2
+small_perimeter_speed = 40
+solid_fill_pattern = rectilinear
+solid_infill_below_area = 70
+solid_infill_every_layers = 0
+solid_infill_extrusion_width = 0
+solid_infill_speed = 60
+spiral_vase = 0
+standby_temperature_delta = -5
+start_perimeters_at_concave_points = 0
+start_perimeters_at_non_overhang = 0
+support_material = 0
+support_material_angle = 0
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_extruder = 1
+support_material_interface_layers = 0
+support_material_interface_spacing = 0
+support_material_pattern = rectilinear
+support_material_spacing = 2.5
+support_material_speed = 60
+support_material_threshold = 0
+thin_walls = 1
+threads = 2
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 50
+top_solid_layers = 5
+travel_speed = 130
+</pre>
+
+Solide Teile:
+<pre style="height:200px;overflow-y:scroll;">
+avoid_crossing_perimeters = 0
+bottom_solid_layers = 3
+bridge_acceleration = 0
+bridge_flow_ratio = 1
+bridge_speed = 60
+brim_width = 3
+complete_objects = 0
+default_acceleration = 0
+external_perimeter_speed = 70%
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extrusion_width = 0
+fill_angle = 45
+fill_density = 0.3
+fill_pattern = honeycomb
+first_layer_acceleration = 0
+first_layer_extrusion_width = 200%
+first_layer_height = 0.22
+first_layer_speed = 30%
+gap_fill_speed = 20
+gcode_comments = 0
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_only_where_needed = 0
+infill_speed = 60
+layer_height = 0.22
+min_skirt_length = 0
+notes =
+only_retract_when_crossing_perimeters = 1
+ooze_prevention = 0
+output_filename_format = [input_filename_base].gcode
+overhangs = 1
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 50
+perimeters = 3
+post_process =
+raft_layers = 0
+randomize_start = 0
+resolution = 0
+skirt_distance = 6
+skirt_height = 1
+skirts = 2
+small_perimeter_speed = 40
+solid_fill_pattern = concentric
+solid_infill_below_area = 70
+solid_infill_every_layers = 0
+solid_infill_extrusion_width = 0
+solid_infill_speed = 60
+spiral_vase = 0
+standby_temperature_delta = -5
+start_perimeters_at_concave_points = 0
+start_perimeters_at_non_overhang = 0
+support_material = 0
+support_material_angle = 0
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_extruder = 1
+support_material_interface_layers = 0
+support_material_interface_spacing = 0
+support_material_pattern = rectilinear
+support_material_spacing = 2.5
+support_material_speed = 60
+support_material_threshold = 0
+thin_walls = 1
+threads = 2
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 50
+top_solid_layers = 5
+travel_speed = 130
+</pre>
+
+=== alte configs ===
+
+==== Von larsan ====
+Ursprünglich die erste Konfiguration für unseren Drucker auf Basis von {{Benutzer|DanielWillmann}}s Konfiguration.
+
+Von der unten stehenden Config gibt es eine verbesserte [https://rohieb.name/stuff/stratum0/larsan-tuned.ini larsan-tuned.ini], die Rohieb gemacht hat.
+
+<pre style="height:200px;overflow:scroll;">
+# generated by Slic3r 0.9.8-dev on Wed Nov 28 08:03:30 2012
+acceleration = 0
+bed_size = 180,200
+bed_temperature = 50
+bottom_solid_layers = 3
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 60
+brim_width = 0
+complete_objects =
+cooling =
+disable_fan_first_layers = 1
+duplicate = 1
+duplicate_distance = 6
+duplicate_grid = 1,1
+end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors
+external_perimeter_speed = 40%
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 30
+extruder_offset = 0x0
+extrusion_axis = E
+extrusion_multiplier = 1
+extrusion_width = 0
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_diameter = 1.75
+fill_angle = 0
+fill_density = 0.15
+fill_pattern = honeycomb
+first_layer_bed_temperature = 50
+first_layer_extrusion_width = 0
+first_layer_height = 0.27
+first_layer_speed = 15%
+first_layer_temperature = 195
+g0 = 0
+gap_fill_speed = 20
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor = reprap
+infill_acceleration = 50
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_speed = 60
+layer_gcode =
+layer_height = 0.24
+max_fan_speed = 100
+min_fan_speed = 35
+min_print_speed = 5
+min_skirt_length = 0
+notes = larsanconfig
+nozzle_diameter = 0.35
+only_retract_when_crossing_perimeters =
+output_filename_format = [input_filename_base].gcode
+perimeter_acceleration = 25
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 50
+perimeters = 3
+post_process =
+print_center = 90,100
+randomize_start = 1
+retract_before_travel = 5
+retract_length = 2
+retract_length_toolchange = 3
+retract_lift = 0
+retract_restart_extra = 0.01
+retract_restart_extra_toolchange = 0
+retract_speed = 50
+rotate = 0
+scale = 1
+skirt_distance = 20
+skirt_height = 1
+skirts = 3
+slowdown_below_layer_time = 50
+small_perimeter_speed = 100%
+solid_fill_pattern = rectilinear
+solid_infill_below_area = 0
+solid_infill_every_layers = 0
+solid_infill_speed = 90%
+start_gcode = G28 ; home all axes\nM92 E820
+support_material =
+support_material_angle = 45
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_pattern = rectilinear
+support_material_spacing = 2
+support_material_speed = 60
+support_material_threshold = 41
+temperature = 185
+threads = 2
+top_solid_infill_speed = 70%
+top_solid_layers = 3
+travel_speed = 50
+use_relative_e_distances = 0
+vibration_limit = 0
+z_offset = 0
+</pre>
+
+==== Schnelle Config von [[Benutzer:Daniel Bohrer|Daniel Bohrer]] (Work in Progress) ====
+Der erste und letzte Layer wird "normal schnell" gedruckt, die anderen doppelt so schnell. Bei dünnen Strukturen (z.B. Mate-Tags) muss man notfalls noch ein bisschen mit der Perimeteranzahl spielen.
+<pre style="height:200px;overflow:scroll;">
+# generated by Slic3r 0.9.4-dev on Fri Nov 16 20:55:02 2012
+acceleration = 0
+bed_size = 180,200
+bed_temperature = 60
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 350
+brim_width = 0
+complete_objects = 0
+cooling = 1
+disable_fan_first_layers = 1
+duplicate = 1
+duplicate_distance = 6
+duplicate_grid = 1,1
+end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors
+external_perimeter_speed = 90%
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extruder_offset = 0x0
+extrusion_axis = E
+extrusion_multiplier = 1.0
+extrusion_width = 0
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_diameter = 1.75
+fill_angle = 0
+fill_density = 0.2
+fill_pattern = rectilinear
+first_layer_bed_temperature = 60
+first_layer_extrusion_width = 0
+first_layer_height = 100%
+first_layer_speed = 20%
+first_layer_temperature = 195
+g0 = 0
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor = reprap
+infill_acceleration = 50
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_speed = 120
+layer_gcode =
+layer_height = 0.25
+max_fan_speed = 100
+min_fan_speed = 35
+min_print_speed = 10
+notes = Used for Mate name tag
+nozzle_diameter = 0.35
+only_retract_when_crossing_perimeters = 0
+output_filename_format = [input_filename_base].gcode
+perimeter_acceleration = 25
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 100
+perimeters = 2
+post_process =
+print_center = 90,100
+randomize_start = 1
+retract_before_travel = 4
+retract_length = 4
+retract_length_toolchange = 3
+retract_lift = 0.5
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 150
+rotate = 0
+scale = 1
+skirt_distance = 10
+skirt_height = 1
+skirts = 2
+slowdown_below_layer_time = 60
+small_perimeter_speed = 80%
+solid_fill_pattern = rectilinear
+solid_infill_below_area = 0
+solid_infill_every_layers = 0
+solid_infill_speed = 100%
+solid_layers = 3
+start_gcode = G28 ; home all axes\nM92 E820
+support_material = 1
+support_material_angle = 45
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_pattern = rectilinear
+support_material_spacing = 3
+support_material_threshold = 45
+temperature = 185
+threads = 3
+top_solid_infill_speed = 50%
+travel_speed = 140
+use_relative_e_distances = 0
+z_offset = 0.22
+</pre>
+
+==== Für Mate-Tags ====
+Konfiguration für Mate-Tags
+<pre style="height:200px;overflow:scroll;">
+# generated by Slic3r 0.9.9-dev on Fri Jun 7 23:59:05 2013
+avoid_crossing_perimeters = 1
+bed_size = 180,200
+bed_temperature = 50
+bottom_solid_layers = 3
+bridge_acceleration = 0
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 50
+brim_width = 0
+complete_objects = 1
+cooling =
+default_acceleration = 0
+disable_fan_first_layers = 1
+duplicate = 1
+duplicate_distance = 6
+duplicate_grid = 1,1
+end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors
+external_perimeter_speed = 50%
+external_perimeters_first = 0
+extra_perimeters =
+extruder_clearance_height = 36
+extruder_clearance_radius = 40
+extruder_offset = 0x0
+extrusion_axis = E
+extrusion_multiplier = 1.1
+extrusion_width = 0
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_diameter = 1.75
+fill_angle = 30
+fill_density = 0.3
+fill_pattern = rectilinear
+first_layer_bed_temperature = 50
+first_layer_extrusion_width = 0
+first_layer_height = 0.27
+first_layer_speed = 40%
+first_layer_temperature = 197
+g0 = 0
+gap_fill_speed = 20
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor = reprap
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_only_where_needed = 0
+infill_speed = 70
+layer_gcode =
+layer_height = 0.24
+max_fan_speed = 100
+min_fan_speed = 35
+min_print_speed = 5
+min_skirt_length = 10
+notes = Config used for bottle name tags (http://www.thingiverse.com/thing:38861)
+nozzle_diameter = 0.33
+only_retract_when_crossing_perimeters = 1
+output_filename_format = [input_filename_base].gcode
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 50
+perimeters = 2
+post_process =
+print_center = 90,100
+raft_layers = 0
+randomize_start =
+resolution = 0
+retract_before_travel = 0
+retract_layer_change = 1
+retract_length = 2
+retract_length_toolchange = 5
+retract_lift = 0
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 50
+rotate = 0
+scale = 1
+skirt_distance = 5
+skirt_height = 1
+skirts = 2
+slowdown_below_layer_time = 50
+small_perimeter_speed = 60%
+solid_fill_pattern = rectilinear
+solid_infill_below_area = 0
+solid_infill_every_layers = 0
+solid_infill_extrusion_width = 0
+solid_infill_speed = 100%
+start_gcode = G28 ; home all axes\nM92 E820
+support_material =
+support_material_angle = 45
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_layers = 0
+support_material_interface_spacing = 0
+support_material_pattern = rectilinear
+support_material_spacing = 2
+support_material_speed = 70
+support_material_threshold = 41
+temperature = 188
+threads = 2
+toolchange_gcode =
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 70%
+top_solid_layers = 3
+travel_speed = 50
+use_relative_e_distances = 0
+vibration_limit = 0
+z_offset = 0
+</pre>
+
+==== von Chrissi^ ====
+* Nette Konfiguration zum Drucken von allem möglichen.
+* First Layer ist super langsam => Guter Druck auch bei kleinen Strukturen
+* First Layer Extrusion Width 110% => Wenig ''Wellenschlagen'' auf dem ersten Layer
+<pre style="height:200px;overflow:scroll;">
+# generated by Slic3r 0.9.3 on Tue Nov 6 21:53:43 2012
+acceleration = 0
+bed_size = 180,200
+bed_temperature = 60
+bridge_fan_speed = 100
+bridge_flow_ratio = 1.05
+bridge_speed = 60
+brim_width = 0
+complete_objects =
+cooling = 1
+disable_fan_first_layers = 1
+duplicate = 1
+duplicate_distance = 6
+duplicate_grid = 1,1
+end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors
+external_perimeter_speed = 100%
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 30
+extruder_offset = 0x0
+extrusion_axis = E
+extrusion_multiplier = 1
+extrusion_width = 100%
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_diameter = 1.75
+fill_angle = 45
+fill_density = 0.1
+fill_pattern = rectilinear
+first_layer_bed_temperature = 60
+first_layer_extrusion_width = 112%
+first_layer_height = 95%
+first_layer_speed = 15%
+first_layer_temperature = 200
+g0 = 0
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor = reprap
+infill_acceleration = 50
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 120%
+infill_speed = 60
+layer_gcode =
+layer_height = 0.3
+max_fan_speed = 100
+min_fan_speed = 35
+min_print_speed = 5
+notes = larsanconfig
+nozzle_diameter = 0.35
+only_retract_when_crossing_perimeters = 1
+output_filename_format = [timestamp]_[input_filename_base].gcode
+perimeter_acceleration = 25
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 60
+perimeters = 2
+post_process =
+print_center = 120,120
+randomize_start = 1
+retract_before_travel = 4
+retract_length = 2
+retract_length_toolchange = 3
+retract_lift = 0
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 50
+rotate = 0
+scale = 1
+skirt_distance = 10
+skirt_height = 1
+skirts = 3
+slowdown_below_layer_time = 50
+small_perimeter_speed = 50%
+solid_fill_pattern = rectilinear
+solid_infill_below_area = 0
+solid_infill_every_layers = 0
+solid_infill_speed = 100%
+solid_layers = 3
+start_gcode = G28 ; home all axes\nM92 E820
+support_material = 1
+support_material_angle = 45
+support_material_extruder = 1
+support_material_extrusion_width = 160%
+support_material_pattern = rectilinear
+support_material_spacing = 2
+support_material_threshold = 40
+temperature = 205
+threads = 2
+top_solid_infill_speed = 40%
+travel_speed = 90
+use_relative_e_distances = 0
+z_offset = 0
+</pre>
+
+==== Gelbes Filament ====
+* Ursprünglich für [[Reprap/Parent]] erstellt
* Damit gedruckt: der letzte gelbe frame-vertex für den Drucker
* etwas wärmer (195°C)
* 0.22 mm z-offeset
use_relative_e_distances = 0
z_offset = 0.22
</pre>
+
+==== RepRap-Config ====
+Konfiguration, mit der die Teile für den RepRap vom [http://netz39.eu Netz39] gedruckt wurden.
+<pre style="height:200px;overflow:scroll;">
+# generated by Slic3r 0.9.9-dev on Mon Jun 3 17:06:48 2013
+avoid_crossing_perimeters = 0
+bed_size = 180,200
+bed_temperature = 50
+bottom_solid_layers = 5
+bridge_acceleration = 0
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 30
+brim_width = 0
+complete_objects = 1
+cooling =
+default_acceleration = 0
+disable_fan_first_layers = 1
+duplicate = 1
+duplicate_distance = 6
+duplicate_grid = 1,1
+end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors
+external_perimeter_speed = 40%
+external_perimeters_first = 0
+extra_perimeters =
+extruder_clearance_height = 35
+extruder_clearance_radius = 62
+extruder_offset = 0x0
+extrusion_axis = E
+extrusion_multiplier = 1.1
+extrusion_width = 0
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_diameter = 1.75
+fill_angle = 30
+fill_density = 0.5
+fill_pattern = rectilinear
+first_layer_bed_temperature = 50
+first_layer_extrusion_width = 0
+first_layer_height = 150%
+first_layer_speed = 40%
+first_layer_temperature = 197
+g0 = 0
+gap_fill_speed = 20
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor = reprap
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_only_where_needed = 0
+infill_speed = 60
+layer_gcode =
+layer_height = 0.2
+max_fan_speed = 100
+min_fan_speed = 35
+min_print_speed = 5
+min_skirt_length = 15
+notes = config for printing netz39 pieces
+nozzle_diameter = 0.33
+only_retract_when_crossing_perimeters = 1
+output_filename_format = [input_filename_base].gcode
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 60
+perimeters = 3
+post_process =
+print_center = 90,100
+raft_layers = 0
+randomize_start =
+resolution = 0
+retract_before_travel = 0
+retract_layer_change = 1
+retract_length = 2
+retract_length_toolchange = 5
+retract_lift = 0
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 50
+rotate = 0
+scale = 1
+skirt_distance = 5
+skirt_height = 1
+skirts = 2
+slowdown_below_layer_time = 50
+small_perimeter_speed = 60%
+solid_fill_pattern = rectilinear
+solid_infill_below_area = 0
+solid_infill_every_layers = 0
+solid_infill_extrusion_width = 0
+solid_infill_speed = 100%
+start_gcode = G28 ; home all axes\nM92 E820
+support_material =
+support_material_angle = 45
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_layers = 0
+support_material_interface_spacing = 0
+support_material_pattern = rectilinear
+support_material_spacing = 2
+support_material_speed = 60
+support_material_threshold = 41
+temperature = 188
+threads = 2
+toolchange_gcode =
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 70%
+top_solid_layers = 5
+travel_speed = 100
+use_relative_e_distances = 0
+vibration_limit = 0
+z_offset = 0
+</pre>
+
+[[Kategorie:RepRap]]
projects / stratum0-wiki.git / blobdiff