/* Musik */ verlinkungen zu label

[stratum0-wiki.git] / 3D-Drucker%2FSlicerBundle.ini.mw

diff --git a/3D-Drucker%2FSlicerBundle.ini.mw b/3D-Drucker%2FSlicerBundle.ini.mw
index ba07e00..03ba5a2 100644 (file)
--- a/3D-Drucker%2FSlicerBundle.ini.mw
+++ b/3D-Drucker%2FSlicerBundle.ini.mw
@@ -1,22 +1,58 @@
-# generated by Slic3r 1.2.9 on Mon May  9 21:40:16 2016
+# generated by Slic3r 1.2.9 on Thu Jun  2 16:16:44 2016

 
 

-[filament:LULZBOT PLA]
+[filament:Lulzbot ABS]
+bed_temperature = 100
+bridge_fan_speed = 100
+cooling = 0
+disable_fan_first_layers = 1
+extrusion_multiplier = 1
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_colour = #FFFFFF
+filament_diameter = 2.85
+first_layer_bed_temperature = 100
+first_layer_temperature = 250
+max_fan_speed = 100
+min_fan_speed = 30
+min_print_speed = 10
+slowdown_below_layer_time = 20
+temperature = 245
+
+[filament:Lulzbot PLA]

 bed_temperature = 50
 bridge_fan_speed = 100
 cooling = 1
 disable_fan_first_layers = 1
 extrusion_multiplier = 1
 bed_temperature = 50
 bridge_fan_speed = 100
 cooling = 1
 disable_fan_first_layers = 1
 extrusion_multiplier = 1

-fan_always_on = 0
+fan_always_on = 1

 fan_below_layer_time = 60
 filament_colour = #FFFFFF
 fan_below_layer_time = 60
 filament_colour = #FFFFFF

-filament_diameter = 2.89
+filament_diameter = 2.85

 first_layer_bed_temperature = 55
 first_layer_bed_temperature = 55

-first_layer_temperature = 190
+first_layer_temperature = 200

 max_fan_speed = 100
 min_fan_speed = 35
 max_fan_speed = 100
 min_fan_speed = 35

-min_print_speed = 25
-slowdown_below_layer_time = 25
-temperature = 185
+min_print_speed = 10
+slowdown_below_layer_time = 30
+temperature = 190
+
+[filament:Lulzbot PLA Weiß]
+bed_temperature = 50
+bridge_fan_speed = 100
+cooling = 1
+disable_fan_first_layers = 1
+extrusion_multiplier = 1
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_colour = #FFFFFF
+filament_diameter = 2.85
+first_layer_bed_temperature = 55
+first_layer_temperature = 200
+max_fan_speed = 100
+min_fan_speed = 30
+min_print_speed = 10
+slowdown_below_layer_time = 20
+temperature = 190

 
 [filament:MendelPro ABS]
 bed_temperature = 0
 
 [filament:MendelPro ABS]
 bed_temperature = 0


@@ -36,7 +72,7 @@ min_print_speed = 5
 slowdown_below_layer_time = 30
 temperature = 245
 
 slowdown_below_layer_time = 30
 temperature = 245
 

-[filament:MendelPro PLA]
+[filament:MendelPro Holz]

 bed_temperature = 50
 bridge_fan_speed = 100
 cooling = 1
 bed_temperature = 50
 bridge_fan_speed = 100
 cooling = 1


@@ -52,8 +88,62 @@ max_fan_speed = 100
 min_fan_speed = 50
 min_print_speed = 5
 slowdown_below_layer_time = 30
 min_fan_speed = 50
 min_print_speed = 5
 slowdown_below_layer_time = 30

+temperature = 185
+
+[filament:MendelPro PLA]
+bed_temperature = 50
+bridge_fan_speed = 100
+cooling = 1
+disable_fan_first_layers = 1
+extrusion_multiplier = 1
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_colour = #FFFFFF
+filament_diameter = 1.7
+first_layer_bed_temperature = 55
+first_layer_temperature = 200
+max_fan_speed = 100
+min_fan_speed = 40
+min_print_speed = 5
+slowdown_below_layer_time = 30

 temperature = 180
 
 temperature = 180
 

+[filament:MendelPro PLA fast]
+bed_temperature = 50
+bridge_fan_speed = 100
+cooling = 1
+disable_fan_first_layers = 1
+extrusion_multiplier = 1
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_colour = #FFFFFF
+filament_diameter = 1.7
+first_layer_bed_temperature = 50
+first_layer_temperature = 200
+max_fan_speed = 100
+min_fan_speed = 50
+min_print_speed = 5
+slowdown_below_layer_time = 30
+temperature = 200
+
+[filament:MendelPro PLA transparent]
+bed_temperature = 50
+bridge_fan_speed = 100
+cooling = 1
+disable_fan_first_layers = 1
+extrusion_multiplier = 1
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_colour = #FFFFFF
+filament_diameter = 1.7
+first_layer_bed_temperature = 55
+first_layer_temperature = 200
+max_fan_speed = 100
+min_fan_speed = 40
+min_print_speed = 5
+slowdown_below_layer_time = 30
+temperature = 200
+

 [filament:TinyBoy PLA]
 bed_temperature = 0
 bridge_fan_speed = 100
 [filament:TinyBoy PLA]
 bed_temperature = 0
 bridge_fan_speed = 100


@@ -72,36 +162,54 @@ min_print_speed = 5
 slowdown_below_layer_time = 15
 temperature = 185
 
 slowdown_below_layer_time = 15
 temperature = 185
 

-[filament:prusa i3 ABS black]
+[filament:Toy]

 bed_temperature = 0
 bridge_fan_speed = 100
 bed_temperature = 0
 bridge_fan_speed = 100

-cooling = 0
-disable_fan_first_layers = 2
+cooling = 1
+disable_fan_first_layers = 1

 extrusion_multiplier = 1
 extrusion_multiplier = 1

-fan_always_on = 0
+fan_always_on = 1

 fan_below_layer_time = 60
 filament_colour = #FFFFFF
 fan_below_layer_time = 60
 filament_colour = #FFFFFF

-filament_diameter = 2.8
+filament_diameter = 1.7

 first_layer_bed_temperature = 0
 first_layer_bed_temperature = 0

-first_layer_temperature = 250
+first_layer_temperature = 200

 max_fan_speed = 100
 max_fan_speed = 100

-min_fan_speed = 35
+min_fan_speed = 100
+min_print_speed = 5
+slowdown_below_layer_time = 30
+temperature = 180
+
+[filament:prusa i3 PLA black fine]
+bed_temperature = 50
+bridge_fan_speed = 100
+cooling = 1
+disable_fan_first_layers = 1
+extrusion_multiplier = 1
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_colour = #FF0000
+filament_diameter = 2.9
+first_layer_bed_temperature = 50
+first_layer_temperature = 200
+max_fan_speed = 100
+min_fan_speed = 100

 min_print_speed = 5
 slowdown_below_layer_time = 15
 min_print_speed = 5
 slowdown_below_layer_time = 15

-temperature = 245
+temperature = 200

 
 

-[filament:prusa i3 PLA klar orange]
+[filament:prusa i3 PLA lila]

 bed_temperature = 50
 bridge_fan_speed = 100
 cooling = 1
 bed_temperature = 50
 bridge_fan_speed = 100
 cooling = 1

-disable_fan_first_layers = 2
+disable_fan_first_layers = 1

 extrusion_multiplier = 1
 fan_always_on = 1
 fan_below_layer_time = 60
 extrusion_multiplier = 1
 fan_always_on = 1
 fan_below_layer_time = 60

-filament_colour = #FFFFFF
-filament_diameter = 2.6
+filament_colour = #8000FF
+filament_diameter = 3

 first_layer_bed_temperature = 50
 first_layer_bed_temperature = 50

-first_layer_temperature = 190
+first_layer_temperature = 200

 max_fan_speed = 100
 min_fan_speed = 35
 min_print_speed = 5
 max_fan_speed = 100
 min_fan_speed = 35
 min_print_speed = 5


@@ -109,73 +217,160 @@ slowdown_below_layer_time = 15
 temperature = 200
 
 [presets]
 temperature = 200
 
 [presets]

-filament = TinyBoy PLA.ini
-print = TinyBoy.ini
-printer = prusa i3.ini
+filament = MendelPro PLA fast.ini
+print = Lulzbot fine.ini
+printer = Lulzbot.ini

 
 

-[print:LULZBOT]
+[print:Lulzbot fine]
+avoid_crossing_perimeters = 1
+bottom_solid_layers = 4
+bridge_acceleration = 0
+bridge_flow_ratio = 1
+bridge_speed = 40
+brim_width = 0
+complete_objects = 0
+default_acceleration = 0
+dont_support_bridges = 1
+external_fill_pattern = rectilinear
+external_perimeter_extrusion_width = 0
+external_perimeter_speed = 30
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extrusion_width = 0
+fill_angle = 35
+fill_density = 30%
+fill_pattern = line
+first_layer_acceleration = 0
+first_layer_extrusion_width = 0
+first_layer_height = 0.2
+first_layer_speed = 10
+gap_fill_speed = 20
+gcode_comments = 0
+infill_acceleration = 0
+infill_every_layers = 2
+infill_extruder = 1
+infill_extrusion_width = 110%
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap = 15%
+infill_speed = 0
+interface_shells = 0
+layer_height = 0.25
+max_print_speed = 100
+max_volumetric_speed = 0
+min_skirt_length = 0
+notes = 
+only_retract_when_crossing_perimeters = 0
+ooze_prevention = 0
+output_filename_format = [input_filename_base].gcode
+overhangs = 1
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 0
+perimeters = 3
+post_process = 
+raft_layers = 0
+resolution = 0
+seam_position = aligned
+skirt_distance = 6
+skirt_height = 1
+skirts = 2
+small_perimeter_speed = 20
+solid_infill_below_area = 30
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 0
+solid_infill_speed = 0
+spiral_vase = 0
+standby_temperature_delta = -5
+support_material = 0
+support_material_angle = 0
+support_material_contact_distance = 0.2
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_extruder = 1
+support_material_interface_layers = 0
+support_material_interface_spacing = 0
+support_material_interface_speed = 100%
+support_material_pattern = rectilinear
+support_material_spacing = 2.5
+support_material_speed = 0
+support_material_threshold = 45
+thin_walls = 1
+threads = 2
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 30
+top_solid_layers = 4
+travel_speed = 100
+xy_size_compensation = 0
+
+[print:MendelPro]

 avoid_crossing_perimeters = 0
 bottom_solid_layers = 3
 avoid_crossing_perimeters = 0
 bottom_solid_layers = 3

-bridge_acceleration = 2000
+bridge_acceleration = 0

 bridge_flow_ratio = 1
 bridge_flow_ratio = 1

-bridge_speed = 72
+bridge_speed = 40

 brim_width = 0
 complete_objects = 0
 brim_width = 0
 complete_objects = 0

-default_acceleration = 2000
+default_acceleration = 0

 dont_support_bridges = 1
 external_fill_pattern = rectilinear
 external_perimeter_extrusion_width = 0
 dont_support_bridges = 1
 external_fill_pattern = rectilinear
 external_perimeter_extrusion_width = 0

-external_perimeter_speed = 45
+external_perimeter_speed = 20

 external_perimeters_first = 0
 extra_perimeters = 1
 extruder_clearance_height = 20
 extruder_clearance_radius = 20
 external_perimeters_first = 0
 extra_perimeters = 1
 extruder_clearance_height = 20
 extruder_clearance_radius = 20

-extrusion_width = 0.42
+extrusion_width = 0

 fill_angle = 45
 fill_angle = 45

-fill_density = 20%
+fill_density = 15%

 fill_pattern = rectilinear
 fill_pattern = rectilinear

-first_layer_acceleration = 2000
-first_layer_extrusion_width = 0.53
+first_layer_acceleration = 0
+first_layer_extrusion_width = 0

 first_layer_height = 0.2
 first_layer_height = 0.2

-first_layer_speed = 75%
-gap_fill_speed = 55
+first_layer_speed = 10
+gap_fill_speed = 10

 gcode_comments = 0
 gcode_comments = 0

-infill_acceleration = 2000
+infill_acceleration = 0

 infill_every_layers = 1
 infill_extruder = 1
 infill_every_layers = 1
 infill_extruder = 1

-infill_extrusion_width = 0.68
+infill_extrusion_width = 0

 infill_first = 0
 infill_only_where_needed = 0
 infill_overlap = 15%
 infill_first = 0
 infill_only_where_needed = 0
 infill_overlap = 15%

-infill_speed = 80
+infill_speed = 0

 interface_shells = 0
 layer_height = 0.2
 max_print_speed = 80
 max_volumetric_speed = 0
 interface_shells = 0
 layer_height = 0.2
 max_print_speed = 80
 max_volumetric_speed = 0

-min_skirt_length = 0
+min_skirt_length = 2

 notes = 
 notes = 

-only_retract_when_crossing_perimeters = 0
+only_retract_when_crossing_perimeters = 1

 ooze_prevention = 0
 output_filename_format = [input_filename_base].gcode
 overhangs = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base].gcode
 overhangs = 1

-perimeter_acceleration = 1200
+perimeter_acceleration = 0

 perimeter_extruder = 1
 perimeter_extruder = 1

-perimeter_extrusion_width = 0.38
-perimeter_speed = 75
+perimeter_extrusion_width = 0
+perimeter_speed = 0

 perimeters = 2
 post_process = 
 raft_layers = 0
 perimeters = 2
 post_process = 
 raft_layers = 0

-resolution = 0.001
+resolution = 0

 seam_position = aligned
 seam_position = aligned

-skirt_distance = 6
+skirt_distance = 1

 skirt_height = 1
 skirt_height = 1

-skirts = 3
-small_perimeter_speed = 50
-solid_infill_below_area = 90
+skirts = 1
+small_perimeter_speed = 10
+solid_infill_below_area = 70

 solid_infill_every_layers = 0
 solid_infill_extruder = 1
 solid_infill_every_layers = 0
 solid_infill_extruder = 1

-solid_infill_extrusion_width = 0.5
-solid_infill_speed = 75
+solid_infill_extrusion_width = 0
+solid_infill_speed = 0

 spiral_vase = 0
 standby_temperature_delta = -5
 support_material = 0
 spiral_vase = 0
 standby_temperature_delta = -5
 support_material = 0


@@ -185,27 +380,27 @@ support_material_enforce_layers = 0
 support_material_extruder = 1
 support_material_extrusion_width = 0
 support_material_interface_extruder = 1
 support_material_extruder = 1
 support_material_extrusion_width = 0
 support_material_interface_extruder = 1

-support_material_interface_layers = 0
+support_material_interface_layers = 2

 support_material_interface_spacing = 0
 support_material_interface_speed = 100%
 support_material_pattern = rectilinear
 support_material_interface_spacing = 0
 support_material_interface_speed = 100%
 support_material_pattern = rectilinear

-support_material_spacing = 2.5
-support_material_speed = 60
-support_material_threshold = 45
+support_material_spacing = 5
+support_material_speed = 0
+support_material_threshold = 40

 thin_walls = 1
 threads = 2
 thin_walls = 1
 threads = 2

-top_infill_extrusion_width = 0.4
-top_solid_infill_speed = 60
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 20

 top_solid_layers = 3
 top_solid_layers = 3

-travel_speed = 160
+travel_speed = 100

 xy_size_compensation = 0
 
 xy_size_compensation = 0
 

-[print:MendelPro]
+[print:MendelPro fast]

 avoid_crossing_perimeters = 0
 bottom_solid_layers = 3
 bridge_acceleration = 0
 bridge_flow_ratio = 1
 avoid_crossing_perimeters = 0
 bottom_solid_layers = 3
 bridge_acceleration = 0
 bridge_flow_ratio = 1

-bridge_speed = 35
+bridge_speed = 40

 brim_width = 0
 complete_objects = 0
 default_acceleration = 0
 brim_width = 0
 complete_objects = 0
 default_acceleration = 0


@@ -219,10 +414,10 @@ extruder_clearance_height = 20
 extruder_clearance_radius = 20
 extrusion_width = 0
 fill_angle = 45
 extruder_clearance_radius = 20
 extrusion_width = 0
 fill_angle = 45

-fill_density = 20%
+fill_density = 15%

 fill_pattern = rectilinear
 first_layer_acceleration = 0
 fill_pattern = rectilinear
 first_layer_acceleration = 0

-first_layer_extrusion_width = 150%
+first_layer_extrusion_width = 0

 first_layer_height = 0.2
 first_layer_speed = 10
 gap_fill_speed = 10
 first_layer_height = 0.2
 first_layer_speed = 10
 gap_fill_speed = 10


@@ -236,10 +431,10 @@ infill_only_where_needed = 0
 infill_overlap = 15%
 infill_speed = 0
 interface_shells = 0
 infill_overlap = 15%
 infill_speed = 0
 interface_shells = 0

-layer_height = 0.2
-max_print_speed = 35
+layer_height = 0.5
+max_print_speed = 80

 max_volumetric_speed = 0
 max_volumetric_speed = 0

-min_skirt_length = 1
+min_skirt_length = 2

 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0


@@ -374,6 +569,180 @@ top_solid_layers = 3
 travel_speed = 100
 xy_size_compensation = 0
 
 travel_speed = 100
 xy_size_compensation = 0
 

+[print:Toy]
+avoid_crossing_perimeters = 0
+bottom_solid_layers = 2
+bridge_acceleration = 0
+bridge_flow_ratio = 1
+bridge_speed = 0
+brim_width = 0
+complete_objects = 0
+default_acceleration = 0
+dont_support_bridges = 1
+external_fill_pattern = rectilinear
+external_perimeter_extrusion_width = 0
+external_perimeter_speed = 0
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extrusion_width = 0
+fill_angle = 45
+fill_density = 0%
+fill_pattern = rectilinear
+first_layer_acceleration = 0
+first_layer_extrusion_width = 0
+first_layer_height = 0.2
+first_layer_speed = 10
+gap_fill_speed = 0
+gcode_comments = 0
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap = 15%
+infill_speed = 0
+interface_shells = 0
+layer_height = 0.2
+max_print_speed = 10
+max_volumetric_speed = 0
+min_skirt_length = 1
+notes = 
+only_retract_when_crossing_perimeters = 1
+ooze_prevention = 0
+output_filename_format = [input_filename_base].gcode
+overhangs = 1
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 0
+perimeters = 2
+post_process = 
+raft_layers = 0
+resolution = 0
+seam_position = aligned
+skirt_distance = 1
+skirt_height = 1
+skirts = 1
+small_perimeter_speed = 0
+solid_infill_below_area = 70
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 0
+solid_infill_speed = 0
+spiral_vase = 0
+standby_temperature_delta = -5
+support_material = 0
+support_material_angle = 0
+support_material_contact_distance = 0.2
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_extruder = 1
+support_material_interface_layers = 2
+support_material_interface_spacing = 0
+support_material_interface_speed = 100%
+support_material_pattern = rectilinear
+support_material_spacing = 5
+support_material_speed = 0
+support_material_threshold = 40
+thin_walls = 1
+threads = 2
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 0
+top_solid_layers = 0
+travel_speed = 100
+xy_size_compensation = 0
+
+[print:prusa i3 100]
+avoid_crossing_perimeters = 0
+bottom_solid_layers = 3
+bridge_acceleration = 0
+bridge_flow_ratio = 1
+bridge_speed = 40
+brim_width = 0
+complete_objects = 0
+default_acceleration = 0
+dont_support_bridges = 1
+external_fill_pattern = rectilinear
+external_perimeter_extrusion_width = 0
+external_perimeter_speed = 10
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extrusion_width = 0
+fill_angle = 45
+fill_density = 20%
+fill_pattern = rectilinear
+first_layer_acceleration = 0
+first_layer_extrusion_width = 0
+first_layer_height = 0.2
+first_layer_speed = 10
+gap_fill_speed = 10
+gcode_comments = 0
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 110%
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap = 15%
+infill_speed = 0
+interface_shells = 0
+layer_height = 0.1
+max_print_speed = 80
+max_volumetric_speed = 0
+min_skirt_length = 1
+notes = 
+only_retract_when_crossing_perimeters = 1
+ooze_prevention = 0
+output_filename_format = [input_filename_base].gcode
+overhangs = 1
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 0
+perimeters = 3
+post_process = 
+raft_layers = 0
+resolution = 0
+seam_position = aligned
+skirt_distance = 6
+skirt_height = 1
+skirts = 3
+small_perimeter_speed = 10
+solid_infill_below_area = 70
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 0
+solid_infill_speed = 0
+spiral_vase = 0
+standby_temperature_delta = -5
+support_material = 0
+support_material_angle = 0
+support_material_contact_distance = 0.2
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_extruder = 1
+support_material_interface_layers = 2
+support_material_interface_spacing = 0
+support_material_interface_speed = 100%
+support_material_pattern = rectilinear
+support_material_spacing = 5
+support_material_speed = 0
+support_material_threshold = 40
+thin_walls = 1
+threads = 2
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 10
+top_solid_layers = 3
+travel_speed = 100
+xy_size_compensation = 0
+

 [print:prusa i3 250]
 avoid_crossing_perimeters = 0
 bottom_solid_layers = 3
 [print:prusa i3 250]
 avoid_crossing_perimeters = 0
 bottom_solid_layers = 3


@@ -466,14 +835,14 @@ avoid_crossing_perimeters = 0
 bottom_solid_layers = 3
 bridge_acceleration = 0
 bridge_flow_ratio = 1
 bottom_solid_layers = 3
 bridge_acceleration = 0
 bridge_flow_ratio = 1

-bridge_speed = 40
+bridge_speed = 60

 brim_width = 0
 complete_objects = 0
 default_acceleration = 0
 dont_support_bridges = 1
 external_fill_pattern = rectilinear
 external_perimeter_extrusion_width = 0
 brim_width = 0
 complete_objects = 0
 default_acceleration = 0
 dont_support_bridges = 1
 external_fill_pattern = rectilinear
 external_perimeter_extrusion_width = 0

-external_perimeter_speed = 10
+external_perimeter_speed = 20

 external_perimeters_first = 0
 extra_perimeters = 1
 extruder_clearance_height = 20
 external_perimeters_first = 0
 extra_perimeters = 1
 extruder_clearance_height = 20


@@ -485,7 +854,7 @@ fill_pattern = rectilinear
 first_layer_acceleration = 0
 first_layer_extrusion_width = 0
 first_layer_height = 0.2
 first_layer_acceleration = 0
 first_layer_extrusion_width = 0
 first_layer_height = 0.2

-first_layer_speed = 15
+first_layer_speed = 10

 gap_fill_speed = 10
 gcode_comments = 0
 infill_acceleration = 0
 gap_fill_speed = 10
 gcode_comments = 0
 infill_acceleration = 0


@@ -553,14 +922,14 @@ avoid_crossing_perimeters = 0
 bottom_solid_layers = 3
 bridge_acceleration = 0
 bridge_flow_ratio = 1
 bottom_solid_layers = 3
 bridge_acceleration = 0
 bridge_flow_ratio = 1

-bridge_speed = 40
+bridge_speed = 60

 brim_width = 0
 complete_objects = 0
 default_acceleration = 0
 dont_support_bridges = 1
 external_fill_pattern = rectilinear
 external_perimeter_extrusion_width = 0
 brim_width = 0
 complete_objects = 0
 default_acceleration = 0
 dont_support_bridges = 1
 external_fill_pattern = rectilinear
 external_perimeter_extrusion_width = 0

-external_perimeter_speed = 10
+external_perimeter_speed = 20

 external_perimeters_first = 0
 extra_perimeters = 1
 extruder_clearance_height = 20
 external_perimeters_first = 0
 extra_perimeters = 1
 extruder_clearance_height = 20


@@ -578,7 +947,7 @@ gcode_comments = 0
 infill_acceleration = 0
 infill_every_layers = 1
 infill_extruder = 1
 infill_acceleration = 0
 infill_every_layers = 1
 infill_extruder = 1

-infill_extrusion_width = 110%
+infill_extrusion_width = 0

 infill_first = 0
 infill_only_where_needed = 0
 infill_overlap = 15%
 infill_first = 0
 infill_only_where_needed = 0
 infill_overlap = 15%


@@ -615,13 +984,13 @@ spiral_vase = 0
 standby_temperature_delta = -5
 support_material = 1
 support_material_angle = 0
 standby_temperature_delta = -5
 support_material = 1
 support_material_angle = 0

-support_material_contact_distance = 0.2
+support_material_contact_distance = 0.3

 support_material_enforce_layers = 0
 support_material_extruder = 1
 support_material_enforce_layers = 0
 support_material_extruder = 1

-support_material_extrusion_width = 0
+support_material_extrusion_width = 90%

 support_material_interface_extruder = 1
 support_material_interface_layers = 2
 support_material_interface_extruder = 1
 support_material_interface_layers = 2

-support_material_interface_spacing = 0
+support_material_interface_spacing = 2

 support_material_interface_speed = 100%
 support_material_pattern = rectilinear
 support_material_spacing = 5
 support_material_interface_speed = 100%
 support_material_pattern = rectilinear
 support_material_spacing = 5


@@ -635,26 +1004,26 @@ top_solid_layers = 3
 travel_speed = 100
 xy_size_compensation = 0
 
 travel_speed = 100
 xy_size_compensation = 0
 

-[printer:LULZBOT]
-bed_shape = 0x0,300x0,300x300,0x300
+[printer:Lulzbot]
+bed_shape = 0x0,298x0,298x275,0x275

 before_layer_gcode = 
 before_layer_gcode = 

-end_gcode = M400      ;   \nM104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200\nG28 X0  ; home X axis\nM84     ; disable motors
+end_gcode = M104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200 ;\nG28 X0 ; home X axis\nM84 ; disable motors

 extruder_offset = 0x0
 gcode_flavor = reprap
 layer_gcode = 
 extruder_offset = 0x0
 gcode_flavor = reprap
 layer_gcode = 

-nozzle_diameter = 0.5
+nozzle_diameter = 0.35

 octoprint_apikey = 
 octoprint_host = 
 pressure_advance = 0
 retract_before_travel = 2
 retract_layer_change = 1
 octoprint_apikey = 
 octoprint_host = 
 pressure_advance = 0
 retract_before_travel = 2
 retract_layer_change = 1

-retract_length = 1.9
+retract_length = 1.75

 retract_length_toolchange = 3
 retract_lift = 0
 retract_restart_extra = 0
 retract_restart_extra_toolchange = 0
 retract_length_toolchange = 3
 retract_lift = 0
 retract_restart_extra = 0
 retract_restart_extra_toolchange = 0

-retract_speed = 30
-start_gcode = G28 ; home all axes
+retract_speed = 20
+start_gcode = G28 ; home all axes\n

 toolchange_gcode = 
 use_firmware_retraction = 0
 use_relative_e_distances = 0
 toolchange_gcode = 
 use_firmware_retraction = 0
 use_relative_e_distances = 0


@@ -666,7 +1035,7 @@ z_offset = 0
 [printer:MendelPro]
 bed_shape = 0x0,220x0,220x177,0x177
 before_layer_gcode = 
 [printer:MendelPro]
 bed_shape = 0x0,220x0,220x177,0x177
 before_layer_gcode = 

-end_gcode = M104 S0        ; turn off temperature\nM140 S0;\nG28 X0           ; home X axis\nM84               ; disable motors\n
+end_gcode = M104 S0        ; turn off temperature\nM140 S0;\nG28 X0           ; home X axis\nG0 Y177;\nM84               ; disable motors\n

 extruder_offset = 0x0
 gcode_flavor = reprap
 layer_gcode = 
 extruder_offset = 0x0
 gcode_flavor = reprap
 layer_gcode = 


@@ -719,6 +1088,34 @@ vibration_limit = 0
 wipe = 0
 z_offset = 0
 
 wipe = 0
 z_offset = 0
 

+[printer:Toyrep]
+bed_shape = 0x0,125x0,125x125,0x125
+before_layer_gcode = 
+end_gcode = M104 S0 ; turn off nozzle temperature\nM84 ; disable motors
+extruder_offset = 0x0
+gcode_flavor = reprap
+layer_gcode = 
+nozzle_diameter = 0.4
+octoprint_apikey = 
+octoprint_host = 
+pressure_advance = 0
+retract_before_travel = 2
+retract_layer_change = 1
+retract_length = 0
+retract_length_toolchange = 3
+retract_lift = 0
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 10
+start_gcode = \n
+toolchange_gcode = 
+use_firmware_retraction = 0
+use_relative_e_distances = 0
+use_volumetric_e = 0
+vibration_limit = 0
+wipe = 0
+z_offset = 0
+

 [printer:prusa i3]
 bed_shape = 0x0,190x0,190x190,0x190
 before_layer_gcode = 
 [printer:prusa i3]
 bed_shape = 0x0,190x0,190x190,0x190
 before_layer_gcode =