X-Git-Url: https://git.rohieb.name/stratum0-wiki.git/blobdiff_plain/117482e57e4d4ba6db76c52fa581a82a1428582c..2d60485b66d3b19b958acd8fa63051869263c437:/RepRap%2FConfigs%2FSlic3r%2FSintox%2Fabs_small.ini.mw diff --git a/RepRap%2FConfigs%2FSlic3r%2FSintox%2Fabs_small.ini.mw b/RepRap%2FConfigs%2FSlic3r%2FSintox%2Fabs_small.ini.mw index e2f544092..94544bb50 100644 --- a/RepRap%2FConfigs%2FSlic3r%2FSintox%2Fabs_small.ini.mw +++ b/RepRap%2FConfigs%2FSlic3r%2FSintox%2Fabs_small.ini.mw @@ -1,6 +1,6 @@ avoid_crossing_perimeters = 0 bed_shape = 0x0,200x0,200x200,0x200 -bed_temperature = 0 +bed_temperature = 80 bottom_solid_layers = 3 bridge_acceleration = 0 bridge_fan_speed = 100 @@ -13,7 +13,7 @@ default_acceleration = 0 disable_fan_first_layers = 1 dont_support_bridges = 1 duplicate_distance = 6 -end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n +end_gcode = M104 S0 ; turn off extruder temperature\nG0 X0 ; move X axis to 0\nG1 Y198 F6000 ; drive print table all the way out\nM84 ; disable motors\n external_perimeter_extrusion_width = 0 external_perimeter_speed = 70% external_perimeters_first = 0 @@ -24,18 +24,18 @@ extruder_offset = 0x0 extrusion_axis = E extrusion_multiplier = 1 extrusion_width = 0 -fan_always_on = 0 +fan_always_on = 1 fan_below_layer_time = 60 -filament_diameter = 3 +filament_diameter = 1.75 fill_angle = 45 fill_density = 40% -fill_pattern = honeycomb +fill_pattern = rectilinear first_layer_acceleration = 0 -first_layer_bed_temperature = 0 +first_layer_bed_temperature = 80 first_layer_extrusion_width = 200% first_layer_height = 0.2 first_layer_speed = 40% -first_layer_temperature = 200 +first_layer_temperature = 240 gap_fill_speed = 20 gcode_arcs = 0 gcode_comments = 0 @@ -89,7 +89,7 @@ solid_infill_extrusion_width = 0 solid_infill_speed = 20 spiral_vase = 0 standby_temperature_delta = -5 -start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n +start_gcode = G28 X0 Y0 ; home X and Y\nG0 X60; move to X60\nG92 X0; set postition to X=0\nG92 Y40; set position to Y=0\nG28 Z0; home Z support_material = 1 support_material_angle = 0 support_material_enforce_layers = 0 @@ -103,13 +103,13 @@ support_material_pattern = rectilinear support_material_spacing = 2.5 support_material_speed = 20 support_material_threshold = 0 -temperature = 200 +temperature = 240 thin_walls = 1 threads = 2 toolchange_gcode = top_infill_extrusion_width = 0 top_solid_infill_speed = 20 -top_solid_layers = 4 +top_solid_layers = 3 travel_speed = 50 use_firmware_retraction = 0 use_relative_e_distances = 0