X-Git-Url: https://git.rohieb.name/stratum0-wiki.git/blobdiff_plain/117482e57e4d4ba6db76c52fa581a82a1428582c..2d60485b66d3b19b958acd8fa63051869263c437:/RepRap%2FConfigs%2FSlic3r%2FSintox%2Fabs_small.ini.mw?ds=sidebyside

diff --git a/RepRap%2FConfigs%2FSlic3r%2FSintox%2Fabs_small.ini.mw b/RepRap%2FConfigs%2FSlic3r%2FSintox%2Fabs_small.ini.mw
index e2f544092..94544bb50 100644
--- a/RepRap%2FConfigs%2FSlic3r%2FSintox%2Fabs_small.ini.mw
+++ b/RepRap%2FConfigs%2FSlic3r%2FSintox%2Fabs_small.ini.mw
@@ -1,6 +1,6 @@
 avoid_crossing_perimeters = 0
 bed_shape = 0x0,200x0,200x200,0x200
-bed_temperature = 0
+bed_temperature = 80
 bottom_solid_layers = 3
 bridge_acceleration = 0
 bridge_fan_speed = 100
@@ -13,7 +13,7 @@ default_acceleration = 0
 disable_fan_first_layers = 1
 dont_support_bridges = 1
 duplicate_distance = 6
-end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors\n
+end_gcode = M104 S0 ; turn off extruder temperature\nG0 X0    ; move X axis to 0\nG1 Y198 F6000 ; drive print table all the way out\nM84     ; disable motors\n
 external_perimeter_extrusion_width = 0
 external_perimeter_speed = 70%
 external_perimeters_first = 0
@@ -24,18 +24,18 @@ extruder_offset = 0x0
 extrusion_axis = E
 extrusion_multiplier = 1
 extrusion_width = 0
-fan_always_on = 0
+fan_always_on = 1
 fan_below_layer_time = 60
-filament_diameter = 3
+filament_diameter = 1.75
 fill_angle = 45
 fill_density = 40%
-fill_pattern = honeycomb
+fill_pattern = rectilinear
 first_layer_acceleration = 0
-first_layer_bed_temperature = 0
+first_layer_bed_temperature = 80
 first_layer_extrusion_width = 200%
 first_layer_height = 0.2
 first_layer_speed = 40%
-first_layer_temperature = 200
+first_layer_temperature = 240
 gap_fill_speed = 20
 gcode_arcs = 0
 gcode_comments = 0
@@ -89,7 +89,7 @@ solid_infill_extrusion_width = 0
 solid_infill_speed = 20
 spiral_vase = 0
 standby_temperature_delta = -5
-start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
+start_gcode = G28 X0 Y0 ; home X and Y\nG0 X60; move to X60\nG92 X0; set postition to X=0\nG92 Y40; set position to Y=0\nG28 Z0; home Z
 support_material = 1
 support_material_angle = 0
 support_material_enforce_layers = 0
@@ -103,13 +103,13 @@ support_material_pattern = rectilinear
 support_material_spacing = 2.5
 support_material_speed = 20
 support_material_threshold = 0
-temperature = 200
+temperature = 240
 thin_walls = 1
 threads = 2
 toolchange_gcode = 
 top_infill_extrusion_width = 0
 top_solid_infill_speed = 20
-top_solid_layers = 4
+top_solid_layers = 3
 travel_speed = 50
 use_firmware_retraction = 0
 use_relative_e_distances = 0