X-Git-Url: https://git.rohieb.name/stratum0-wiki.git/blobdiff_plain/7c5c7bc6f9f5922e66ba7b110c5463ffc159913a..7c13b02eaadf52ad0a19e1ca699d06e560aa8066:/RepRap%2FConfigs%2FSlic3r.mw
diff --git a/RepRap%2FConfigs%2FSlic3r.mw b/RepRap%2FConfigs%2FSlic3r.mw
index cdeb90237..13cbcef6e 100644
--- a/RepRap%2FConfigs%2FSlic3r.mw
+++ b/RepRap%2FConfigs%2FSlic3r.mw
@@ -1,520 +1 @@
-Eine Seite um (gute) Beispielkonfigkurationen zu sammeln, am besten mit Beispieldruck (Foto)
-
-Es gibt vermutlich nicht ''die eine Ideal-Konfiguration'' die für alle Teile gut funktioniert, mit den hier gelisteten sollte aber ein Druck einigermaÃen gelingen.
-
-===== Von larsan =====
-Ursprünglich die erste Konfiguration für unseren Drucker auf Basis von {{Benutzer|DanielWillmann}}s Konfiguration.
-
-Von der unten stehenden Config gibt es eine verbesserte [https://rohieb.name/stuff/stratum0/larsan-tuned.ini larsan-tuned.ini], die Rohieb gemacht hat.
-
-
-# generated by Slic3r 0.9.8-dev on Wed Nov 28 08:03:30 2012
-acceleration = 0
-bed_size = 180,200
-bed_temperature = 50
-bottom_solid_layers = 3
-bridge_fan_speed = 100
-bridge_flow_ratio = 1
-bridge_speed = 60
-brim_width = 0
-complete_objects =
-cooling =
-disable_fan_first_layers = 1
-duplicate = 1
-duplicate_distance = 6
-duplicate_grid = 1,1
-end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors
-external_perimeter_speed = 40%
-extra_perimeters = 1
-extruder_clearance_height = 20
-extruder_clearance_radius = 30
-extruder_offset = 0x0
-extrusion_axis = E
-extrusion_multiplier = 1
-extrusion_width = 0
-fan_always_on = 0
-fan_below_layer_time = 60
-filament_diameter = 1.75
-fill_angle = 0
-fill_density = 0.15
-fill_pattern = honeycomb
-first_layer_bed_temperature = 50
-first_layer_extrusion_width = 0
-first_layer_height = 0.27
-first_layer_speed = 15%
-first_layer_temperature = 195
-g0 = 0
-gap_fill_speed = 20
-gcode_arcs = 0
-gcode_comments = 0
-gcode_flavor = reprap
-infill_acceleration = 50
-infill_every_layers = 1
-infill_extruder = 1
-infill_extrusion_width = 0
-infill_speed = 60
-layer_gcode =
-layer_height = 0.24
-max_fan_speed = 100
-min_fan_speed = 35
-min_print_speed = 5
-min_skirt_length = 0
-notes = larsanconfig
-nozzle_diameter = 0.35
-only_retract_when_crossing_perimeters =
-output_filename_format = [input_filename_base].gcode
-perimeter_acceleration = 25
-perimeter_extruder = 1
-perimeter_extrusion_width = 0
-perimeter_speed = 50
-perimeters = 3
-post_process =
-print_center = 90,100
-randomize_start = 1
-retract_before_travel = 5
-retract_length = 2
-retract_length_toolchange = 3
-retract_lift = 0
-retract_restart_extra = 0.01
-retract_restart_extra_toolchange = 0
-retract_speed = 50
-rotate = 0
-scale = 1
-skirt_distance = 20
-skirt_height = 1
-skirts = 3
-slowdown_below_layer_time = 50
-small_perimeter_speed = 100%
-solid_fill_pattern = rectilinear
-solid_infill_below_area = 0
-solid_infill_every_layers = 0
-solid_infill_speed = 90%
-start_gcode = G28 ; home all axes\nM92 E820
-support_material =
-support_material_angle = 45
-support_material_extruder = 1
-support_material_extrusion_width = 0
-support_material_pattern = rectilinear
-support_material_spacing = 2
-support_material_speed = 60
-support_material_threshold = 41
-temperature = 185
-threads = 2
-top_solid_infill_speed = 70%
-top_solid_layers = 3
-travel_speed = 50
-use_relative_e_distances = 0
-vibration_limit = 0
-z_offset = 0
-
-
-== Schnelle Config von [[Benutzer:Daniel Bohrer|Daniel Bohrer]] (Work in Progress) ==
-Der erste und letzte Layer wird "normal schnell" gedruckt, die anderen doppelt so schnell. Bei dünnen Strukturen (z.B. Mate-Tags) muss man notfalls noch ein bisschen mit der Perimeteranzahl spielen.
-
-# generated by Slic3r 0.9.4-dev on Fri Nov 16 20:55:02 2012
-acceleration = 0
-bed_size = 180,200
-bed_temperature = 60
-bridge_fan_speed = 100
-bridge_flow_ratio = 1
-bridge_speed = 350
-brim_width = 0
-complete_objects = 0
-cooling = 1
-disable_fan_first_layers = 1
-duplicate = 1
-duplicate_distance = 6
-duplicate_grid = 1,1
-end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors
-external_perimeter_speed = 90%
-extra_perimeters = 1
-extruder_clearance_height = 20
-extruder_clearance_radius = 20
-extruder_offset = 0x0
-extrusion_axis = E
-extrusion_multiplier = 1.0
-extrusion_width = 0
-fan_always_on = 0
-fan_below_layer_time = 60
-filament_diameter = 1.75
-fill_angle = 0
-fill_density = 0.2
-fill_pattern = rectilinear
-first_layer_bed_temperature = 60
-first_layer_extrusion_width = 0
-first_layer_height = 100%
-first_layer_speed = 20%
-first_layer_temperature = 195
-g0 = 0
-gcode_arcs = 0
-gcode_comments = 0
-gcode_flavor = reprap
-infill_acceleration = 50
-infill_every_layers = 1
-infill_extruder = 1
-infill_extrusion_width = 0
-infill_speed = 120
-layer_gcode =
-layer_height = 0.25
-max_fan_speed = 100
-min_fan_speed = 35
-min_print_speed = 10
-notes = Used for Mate name tag
-nozzle_diameter = 0.35
-only_retract_when_crossing_perimeters = 0
-output_filename_format = [input_filename_base].gcode
-perimeter_acceleration = 25
-perimeter_extruder = 1
-perimeter_extrusion_width = 0
-perimeter_speed = 100
-perimeters = 2
-post_process =
-print_center = 90,100
-randomize_start = 1
-retract_before_travel = 4
-retract_length = 4
-retract_length_toolchange = 3
-retract_lift = 0.5
-retract_restart_extra = 0
-retract_restart_extra_toolchange = 0
-retract_speed = 150
-rotate = 0
-scale = 1
-skirt_distance = 10
-skirt_height = 1
-skirts = 2
-slowdown_below_layer_time = 60
-small_perimeter_speed = 80%
-solid_fill_pattern = rectilinear
-solid_infill_below_area = 0
-solid_infill_every_layers = 0
-solid_infill_speed = 100%
-solid_layers = 3
-start_gcode = G28 ; home all axes\nM92 E820
-support_material = 1
-support_material_angle = 45
-support_material_extruder = 1
-support_material_extrusion_width = 0
-support_material_pattern = rectilinear
-support_material_spacing = 3
-support_material_threshold = 45
-temperature = 185
-threads = 3
-top_solid_infill_speed = 50%
-travel_speed = 140
-use_relative_e_distances = 0
-z_offset = 0.22
-
-
-== von Chrissi^ ==
-* Nette Konfiguration zum Drucken von allem möglichen.
-* First Layer ist super langsam => Guter Druck auch bei kleinen Strukturen
-* First Layer Extrusion Width 110% => Wenig ''Wellenschlagen'' auf dem ersten Layer
-
-# generated by Slic3r 0.9.3 on Tue Nov 6 21:53:43 2012
-acceleration = 0
-bed_size = 180,200
-bed_temperature = 60
-bridge_fan_speed = 100
-bridge_flow_ratio = 1.05
-bridge_speed = 60
-brim_width = 0
-complete_objects =
-cooling = 1
-disable_fan_first_layers = 1
-duplicate = 1
-duplicate_distance = 6
-duplicate_grid = 1,1
-end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors
-external_perimeter_speed = 100%
-extra_perimeters = 1
-extruder_clearance_height = 20
-extruder_clearance_radius = 30
-extruder_offset = 0x0
-extrusion_axis = E
-extrusion_multiplier = 1
-extrusion_width = 100%
-fan_always_on = 0
-fan_below_layer_time = 60
-filament_diameter = 1.75
-fill_angle = 45
-fill_density = 0.1
-fill_pattern = rectilinear
-first_layer_bed_temperature = 60
-first_layer_extrusion_width = 112%
-first_layer_height = 95%
-first_layer_speed = 15%
-first_layer_temperature = 200
-g0 = 0
-gcode_arcs = 0
-gcode_comments = 0
-gcode_flavor = reprap
-infill_acceleration = 50
-infill_every_layers = 1
-infill_extruder = 1
-infill_extrusion_width = 120%
-infill_speed = 60
-layer_gcode =
-layer_height = 0.3
-max_fan_speed = 100
-min_fan_speed = 35
-min_print_speed = 5
-notes = larsanconfig
-nozzle_diameter = 0.35
-only_retract_when_crossing_perimeters = 1
-output_filename_format = [timestamp]_[input_filename_base].gcode
-perimeter_acceleration = 25
-perimeter_extruder = 1
-perimeter_extrusion_width = 0
-perimeter_speed = 60
-perimeters = 2
-post_process =
-print_center = 120,120
-randomize_start = 1
-retract_before_travel = 4
-retract_length = 2
-retract_length_toolchange = 3
-retract_lift = 0
-retract_restart_extra = 0
-retract_restart_extra_toolchange = 0
-retract_speed = 50
-rotate = 0
-scale = 1
-skirt_distance = 10
-skirt_height = 1
-skirts = 3
-slowdown_below_layer_time = 50
-small_perimeter_speed = 50%
-solid_fill_pattern = rectilinear
-solid_infill_below_area = 0
-solid_infill_every_layers = 0
-solid_infill_speed = 100%
-solid_layers = 3
-start_gcode = G28 ; home all axes\nM92 E820
-support_material = 1
-support_material_angle = 45
-support_material_extruder = 1
-support_material_extrusion_width = 160%
-support_material_pattern = rectilinear
-support_material_spacing = 2
-support_material_threshold = 40
-temperature = 205
-threads = 2
-top_solid_infill_speed = 40%
-travel_speed = 90
-use_relative_e_distances = 0
-z_offset = 0
-
-
-== Gelbes Filament ==
-* Ursprünglich für [[Reprap/Parent]] erstellt
-* Damit gedruckt: der letzte gelbe frame-vertex für den Drucker
-* etwas wärmer (195°C)
-* 0.22 mm z-offeset
-
-acceleration = 0
-bed_size = 170,170
-bed_temperature = 60
-bridge_fan_speed = 100
-bridge_flow_ratio = 1
-bridge_speed = 30
-brim_width = 0
-complete_objects = 0
-cooling = 1
-disable_fan_first_layers = 1
-duplicate = 1
-duplicate_distance = 6
-duplicate_grid = 1,1
-end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors
-external_perimeter_speed = 90%
-extra_perimeters = 1
-extruder_clearance_height = 20
-extruder_clearance_radius = 20
-extrusion_axis = E
-extrusion_multiplier = 1
-extrusion_width = 0
-fan_always_on = 0
-fan_below_layer_time = 60
-filament_diameter = 3
-fill_angle = 45
-fill_density = 0.15
-fill_pattern = rectilinear
-first_layer_bed_temperature = 60
-first_layer_extrusion_width = 0
-first_layer_height = 115%
-first_layer_speed = 80%
-first_layer_temperature = 200
-g0 = 0
-gcode_arcs = 0
-gcode_comments = 0
-gcode_flavor = reprap
-infill_acceleration = 50
-infill_every_layers = 1
-infill_extruder = 1
-infill_extrusion_width = 0
-infill_speed = 40
-layer_gcode =
-layer_height = 0.28
-max_fan_speed = 100
-min_fan_speed = 35
-min_print_speed = 10
-notes = Used for Mate name tag
-nozzle_diameter = 0.35
-output_filename_format = [input_filename_base].gcode
-perimeter_acceleration = 25
-perimeter_speed = 30
-perimeters = 3
-perimeters_extruder = 1
-perimeters_extrusion_width = 0
-post_process =
-print_center = 50,27
-randomize_start = 1
-retract_before_travel = 4
-retract_length = 3
-retract_lift = 0.4
-retract_restart_extra = 0
-retract_speed = 30
-rotate = 0
-scale = 1
-skirt_distance = 6
-skirt_height = 1
-skirts = 3
-slowdown_below_layer_time = 60
-small_perimeter_speed = 30
-solid_fill_pattern = rectilinear
-solid_infill_speed = 40
-solid_layers = 3
-start_gcode = G28 ; home all axes\nM92 E820
-support_material =
-support_material_angle = 45
-support_material_extruder = 1
-support_material_extrusion_width = 0
-support_material_pattern = rectilinear
-support_material_spacing = 2.5
-support_material_threshold = 45
-temperature = 195
-threads = 2
-top_solid_infill_speed = 40
-travel_speed = 130
-use_relative_e_distances = 0
-z_offset = 0.22
-
-
-== Gelbes Filament ==
-Konfiguration, mit der die Teile für den RepRap vom [http://netz39.eu Netz39] gedruckt wurden.
-
-# generated by Slic3r 0.9.9-dev on Mon Jun 3 17:06:48 2013
-avoid_crossing_perimeters = 0
-bed_size = 180,200
-bed_temperature = 50
-bottom_solid_layers = 5
-bridge_acceleration = 0
-bridge_fan_speed = 100
-bridge_flow_ratio = 1
-bridge_speed = 30
-brim_width = 0
-complete_objects = 1
-cooling =
-default_acceleration = 0
-disable_fan_first_layers = 1
-duplicate = 1
-duplicate_distance = 6
-duplicate_grid = 1,1
-end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors
-external_perimeter_speed = 40%
-external_perimeters_first = 0
-extra_perimeters =
-extruder_clearance_height = 35
-extruder_clearance_radius = 62
-extruder_offset = 0x0
-extrusion_axis = E
-extrusion_multiplier = 1.1
-extrusion_width = 0
-fan_always_on = 0
-fan_below_layer_time = 60
-filament_diameter = 1.75
-fill_angle = 30
-fill_density = 0.5
-fill_pattern = rectilinear
-first_layer_bed_temperature = 50
-first_layer_extrusion_width = 0
-first_layer_height = 150%
-first_layer_speed = 40%
-first_layer_temperature = 197
-g0 = 0
-gap_fill_speed = 20
-gcode_arcs = 0
-gcode_comments = 0
-gcode_flavor = reprap
-infill_acceleration = 0
-infill_every_layers = 1
-infill_extruder = 1
-infill_extrusion_width = 0
-infill_first = 0
-infill_only_where_needed = 0
-infill_speed = 60
-layer_gcode =
-layer_height = 0.2
-max_fan_speed = 100
-min_fan_speed = 35
-min_print_speed = 5
-min_skirt_length = 15
-notes = config for printing netz39 pieces
-nozzle_diameter = 0.33
-only_retract_when_crossing_perimeters = 1
-output_filename_format = [input_filename_base].gcode
-perimeter_acceleration = 0
-perimeter_extruder = 1
-perimeter_extrusion_width = 0
-perimeter_speed = 60
-perimeters = 3
-post_process =
-print_center = 90,100
-raft_layers = 0
-randomize_start =
-resolution = 0
-retract_before_travel = 0
-retract_layer_change = 1
-retract_length = 2
-retract_length_toolchange = 5
-retract_lift = 0
-retract_restart_extra = 0
-retract_restart_extra_toolchange = 0
-retract_speed = 50
-rotate = 0
-scale = 1
-skirt_distance = 5
-skirt_height = 1
-skirts = 2
-slowdown_below_layer_time = 50
-small_perimeter_speed = 60%
-solid_fill_pattern = rectilinear
-solid_infill_below_area = 0
-solid_infill_every_layers = 0
-solid_infill_extrusion_width = 0
-solid_infill_speed = 100%
-start_gcode = G28 ; home all axes\nM92 E820
-support_material =
-support_material_angle = 45
-support_material_enforce_layers = 0
-support_material_extruder = 1
-support_material_extrusion_width = 0
-support_material_interface_layers = 0
-support_material_interface_spacing = 0
-support_material_pattern = rectilinear
-support_material_spacing = 2
-support_material_speed = 60
-support_material_threshold = 41
-temperature = 188
-threads = 2
-toolchange_gcode =
-top_infill_extrusion_width = 0
-top_solid_infill_speed = 70%
-top_solid_layers = 5
-travel_speed = 100
-use_relative_e_distances = 0
-vibration_limit = 0
-z_offset = 0
-
-
-[[Kategorie:RepRap]]
+#redirect [[3D-Drucken#Slic3r-Einstellungen]]