X-Git-Url: https://git.rohieb.name/stratum0-wiki.git/blobdiff_plain/916090ac88c00d2c7fa64a3f973ac3d9872f46f3..366a8840dfe6c708700b657b7bcfc6f5f0889956:/3D-Drucker%2FSlicerBundle.ini.mw diff --git a/3D-Drucker%2FSlicerBundle.ini.mw b/3D-Drucker%2FSlicerBundle.ini.mw index 8d2478952..bca5b64b7 100644 --- a/3D-Drucker%2FSlicerBundle.ini.mw +++ b/3D-Drucker%2FSlicerBundle.ini.mw @@ -1,42 +1,24 @@ -# generated by Slic3r 1.2.9 on Fri May 13 17:04:53 2016 +# generated by Slic3r 1.2.9 on Mon Jan 30 16:49:14 2017 -[filament:LULZBOT ABS fine] -bed_temperature = 100 -bridge_fan_speed = 0 +[filament:1.75mm ABS] +bed_temperature = 0 +bridge_fan_speed = 35 cooling = 1 disable_fan_first_layers = 1 extrusion_multiplier = 1 fan_always_on = 0 fan_below_layer_time = 60 filament_colour = #FFFFFF -filament_diameter = 2.89 -first_layer_bed_temperature = 100 +filament_diameter = 1.75 +first_layer_bed_temperature = 0 first_layer_temperature = 250 max_fan_speed = 0 min_fan_speed = 0 -min_print_speed = 15 -slowdown_below_layer_time = 20 -temperature = 240 - -[filament:MendelPro ABS] -bed_temperature = 0 -bridge_fan_speed = 100 -cooling = 0 -disable_fan_first_layers = 1 -extrusion_multiplier = 1 -fan_always_on = 0 -fan_below_layer_time = 60 -filament_colour = #FFFFFF -filament_diameter = 1.7 -first_layer_bed_temperature = 0 -first_layer_temperature = 250 -max_fan_speed = 100 -min_fan_speed = 50 min_print_speed = 5 -slowdown_below_layer_time = 30 -temperature = 245 +slowdown_below_layer_time = 10 +temperature = 230 -[filament:MendelPro Holz] +[filament:1.75mm Holz] bed_temperature = 50 bridge_fan_speed = 100 cooling = 1 @@ -45,322 +27,220 @@ extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 60 filament_colour = #FFFFFF -filament_diameter = 1.7 -first_layer_bed_temperature = 55 +filament_diameter = 1.75 +first_layer_bed_temperature = 50 first_layer_temperature = 200 max_fan_speed = 100 min_fan_speed = 50 min_print_speed = 5 -slowdown_below_layer_time = 30 -temperature = 185 +slowdown_below_layer_time = 10 +temperature = 190 -[filament:MendelPro PLA] +[filament:1.75mm PLA] bed_temperature = 50 bridge_fan_speed = 100 cooling = 1 -disable_fan_first_layers = 1 +disable_fan_first_layers = 3 extrusion_multiplier = 1 -fan_always_on = 1 +fan_always_on = 0 fan_below_layer_time = 60 filament_colour = #FFFFFF -filament_diameter = 1.7 -first_layer_bed_temperature = 55 -first_layer_temperature = 200 +filament_diameter = 1.75 +first_layer_bed_temperature = 50 +first_layer_temperature = 220 max_fan_speed = 100 -min_fan_speed = 50 +min_fan_speed = 100 min_print_speed = 5 -slowdown_below_layer_time = 30 -temperature = 180 +slowdown_below_layer_time = 20 +temperature = 190 -[filament:TinyBoy PLA] +[filament:1.75mm PLA TinyBoy] bed_temperature = 0 bridge_fan_speed = 100 cooling = 1 disable_fan_first_layers = 2 -extrusion_multiplier = 0.9 +extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 60 -filament_colour = #35E1FF -filament_diameter = 1.7 +filament_colour = #FF8000 +filament_diameter = 1.75 first_layer_bed_temperature = 0 first_layer_temperature = 200 -max_fan_speed = 50 +max_fan_speed = 40 min_fan_speed = 35 min_print_speed = 5 -slowdown_below_layer_time = 15 -temperature = 185 +slowdown_below_layer_time = 10 +temperature = 200 -[filament:prusa i3 PLA black fine] -bed_temperature = 50 +[filament:2.70mm PLA] +bed_temperature = 60 bridge_fan_speed = 100 cooling = 1 -disable_fan_first_layers = 1 +disable_fan_first_layers = 3 extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 60 -filament_colour = #FF0000 -filament_diameter = 2.9 -first_layer_bed_temperature = 50 -first_layer_temperature = 200 +filament_colour = #FF00FF +filament_diameter = 2.72 +first_layer_bed_temperature = 60 +first_layer_temperature = 220 max_fan_speed = 100 min_fan_speed = 100 min_print_speed = 5 -slowdown_below_layer_time = 15 +slowdown_below_layer_time = 20 temperature = 200 -[filament:prusa i3 PLA igus] -bed_temperature = 50 +[filament:2.80mm PETG ] +bed_temperature = 75 bridge_fan_speed = 100 -cooling = 0 +cooling = 1 +disable_fan_first_layers = 3 +extrusion_multiplier = 1 +fan_always_on = 1 +fan_below_layer_time = 60 +filament_colour = #B1EB96 +filament_diameter = 2.8 +first_layer_bed_temperature = 75 +first_layer_temperature = 245 +max_fan_speed = 100 +min_fan_speed = 100 +min_print_speed = 5 +slowdown_below_layer_time = 10 +temperature = 235 + +[filament:2.85mm ABS] +bed_temperature = 100 +bridge_fan_speed = 35 +cooling = 1 disable_fan_first_layers = 1 -extrusion_multiplier = 0.9 +extrusion_multiplier = 1 fan_always_on = 0 fan_below_layer_time = 60 -filament_colour = #D0C9B0 -filament_diameter = 2.9 -first_layer_bed_temperature = 50 +filament_colour = #FFFFFF +filament_diameter = 2.85 +first_layer_bed_temperature = 100 first_layer_temperature = 250 +max_fan_speed = 0 +min_fan_speed = 0 +min_print_speed = 5 +slowdown_below_layer_time = 10 +temperature = 235 + +[filament:2.85mm PETG ] +bed_temperature = 75 +bridge_fan_speed = 100 +cooling = 1 +disable_fan_first_layers = 3 +extrusion_multiplier = 1 +fan_always_on = 1 +fan_below_layer_time = 60 +filament_colour = #B1EB96 +filament_diameter = 2.85 +first_layer_bed_temperature = 75 +first_layer_temperature = 245 max_fan_speed = 100 -min_fan_speed = 35 +min_fan_speed = 100 min_print_speed = 5 -slowdown_below_layer_time = 15 -temperature = 250 +slowdown_below_layer_time = 10 +temperature = 235 -[filament:prusa i3 PLA rot] -bed_temperature = 50 +[filament:2.85mm PLA] +bed_temperature = 60 bridge_fan_speed = 100 cooling = 1 -disable_fan_first_layers = 1 +disable_fan_first_layers = 3 extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 60 -filament_colour = #FF0000 -filament_diameter = 2.9 -first_layer_bed_temperature = 50 -first_layer_temperature = 200 +filament_colour = #FF00FF +filament_diameter = 2.85 +first_layer_bed_temperature = 60 +first_layer_temperature = 220 max_fan_speed = 100 -min_fan_speed = 35 +min_fan_speed = 100 min_print_speed = 5 -slowdown_below_layer_time = 15 -temperature = 200 +slowdown_below_layer_time = 20 +temperature = 195 -[presets] -filament = LULZBOT ABS fine.ini -print = prusa i3 100.ini -printer = LULZBOT ABS fine.ini +[filament:2.85mm PLA hot] +bed_temperature = 60 +bridge_fan_speed = 100 +cooling = 1 +disable_fan_first_layers = 1 +extrusion_multiplier = 1 +fan_always_on = 1 +fan_below_layer_time = 60 +filament_colour = #FF00FF +filament_diameter = 2.85 +first_layer_bed_temperature = 60 +first_layer_temperature = 215 +max_fan_speed = 100 +min_fan_speed = 100 +min_print_speed = 5 +slowdown_below_layer_time = 10 +temperature = 215 -[print:LULZBOT ABS fine ] -avoid_crossing_perimeters = 1 -bottom_solid_layers = 2 -bridge_acceleration = 1000 -bridge_flow_ratio = 1.1 -bridge_speed = 40 -brim_width = 0 -complete_objects = 0 -default_acceleration = 900 -dont_support_bridges = 1 -external_fill_pattern = rectilinear -external_perimeter_extrusion_width = 0 -external_perimeter_speed = 30 -external_perimeters_first = 0 -extra_perimeters = 1 -extruder_clearance_height = 20 -extruder_clearance_radius = 20 -extrusion_width = 0.37 -fill_angle = 35 -fill_density = 30% -fill_pattern = line -first_layer_acceleration = 0 -first_layer_extrusion_width = 0.37 -first_layer_height = 120% -first_layer_speed = 85% -gap_fill_speed = 45 -gcode_comments = 0 -infill_acceleration = 1400 -infill_every_layers = 2 -infill_extruder = 1 -infill_extrusion_width = 0.6 -infill_first = 0 -infill_only_where_needed = 0 -infill_overlap = 15% -infill_speed = 70 -interface_shells = 0 -layer_height = 0.14 -max_print_speed = 80 -max_volumetric_speed = 0 -min_skirt_length = 0 -notes = -only_retract_when_crossing_perimeters = 0 -ooze_prevention = 0 -output_filename_format = [input_filename_base].gcode -overhangs = 1 -perimeter_acceleration = 900 -perimeter_extruder = 1 -perimeter_extrusion_width = 0.34 -perimeter_speed = 40 -perimeters = 4 -post_process = -raft_layers = 0 -resolution = 0 -seam_position = aligned -skirt_distance = 6 -skirt_height = 1 -skirts = 2 -small_perimeter_speed = 30 -solid_infill_below_area = 30 -solid_infill_every_layers = 0 -solid_infill_extruder = 1 -solid_infill_extrusion_width = 0 -solid_infill_speed = 60 -spiral_vase = 0 -standby_temperature_delta = -5 -support_material = 0 -support_material_angle = 0 -support_material_contact_distance = 0.2 -support_material_enforce_layers = 0 -support_material_extruder = 1 -support_material_extrusion_width = 0 -support_material_interface_extruder = 1 -support_material_interface_layers = 0 -support_material_interface_spacing = 0 -support_material_interface_speed = 100% -support_material_pattern = rectilinear -support_material_spacing = 2.5 -support_material_speed = 60 -support_material_threshold = 45 -thin_walls = 1 -threads = 2 -top_infill_extrusion_width = 0.35 -top_solid_infill_speed = 80% -top_solid_layers = 4 -travel_speed = 80 -xy_size_compensation = 0 +[filament:2.85mm Willowflex] +bed_temperature = 70 +bridge_fan_speed = 100 +cooling = 1 +disable_fan_first_layers = 1 +extrusion_multiplier = 1 +fan_always_on = 1 +fan_below_layer_time = 60 +filament_colour = #BF0005 +filament_diameter = 2.85 +first_layer_bed_temperature = 70 +first_layer_temperature = 160 +max_fan_speed = 100 +min_fan_speed = 50 +min_print_speed = 5 +slowdown_below_layer_time = 20 +temperature = 160 -[print:MendelPro] -avoid_crossing_perimeters = 0 -bottom_solid_layers = 3 -bridge_acceleration = 0 -bridge_flow_ratio = 1 -bridge_speed = 35 -brim_width = 0 -complete_objects = 0 -default_acceleration = 0 -dont_support_bridges = 1 -external_fill_pattern = rectilinear -external_perimeter_extrusion_width = 0 -external_perimeter_speed = 20 -external_perimeters_first = 0 -extra_perimeters = 1 -extruder_clearance_height = 20 -extruder_clearance_radius = 20 -extrusion_width = 0 -fill_angle = 45 -fill_density = 15% -fill_pattern = rectilinear -first_layer_acceleration = 0 -first_layer_extrusion_width = 150% -first_layer_height = 0.2 -first_layer_speed = 10 -gap_fill_speed = 10 -gcode_comments = 0 -infill_acceleration = 0 -infill_every_layers = 1 -infill_extruder = 1 -infill_extrusion_width = 0 -infill_first = 0 -infill_only_where_needed = 0 -infill_overlap = 15% -infill_speed = 0 -interface_shells = 0 -layer_height = 0.2 -max_print_speed = 35 -max_volumetric_speed = 0 -min_skirt_length = 1 -notes = -only_retract_when_crossing_perimeters = 1 -ooze_prevention = 0 -output_filename_format = [input_filename_base].gcode -overhangs = 1 -perimeter_acceleration = 0 -perimeter_extruder = 1 -perimeter_extrusion_width = 0 -perimeter_speed = 0 -perimeters = 2 -post_process = -raft_layers = 0 -resolution = 0 -seam_position = aligned -skirt_distance = 1 -skirt_height = 1 -skirts = 1 -small_perimeter_speed = 10 -solid_infill_below_area = 70 -solid_infill_every_layers = 0 -solid_infill_extruder = 1 -solid_infill_extrusion_width = 0 -solid_infill_speed = 0 -spiral_vase = 0 -standby_temperature_delta = -5 -support_material = 0 -support_material_angle = 0 -support_material_contact_distance = 0.2 -support_material_enforce_layers = 0 -support_material_extruder = 1 -support_material_extrusion_width = 0 -support_material_interface_extruder = 1 -support_material_interface_layers = 2 -support_material_interface_spacing = 0 -support_material_interface_speed = 100% -support_material_pattern = rectilinear -support_material_spacing = 5 -support_material_speed = 0 -support_material_threshold = 40 -thin_walls = 1 -threads = 2 -top_infill_extrusion_width = 0 -top_solid_infill_speed = 20 -top_solid_layers = 3 -travel_speed = 100 -xy_size_compensation = 0 +[presets] +filament = 2.80mm PETG .ini +print = Lulzbot.ini +printer = MendelPro.ini -[print:TinyBoy] +[print:Lulzbot] avoid_crossing_perimeters = 0 -bottom_solid_layers = 3 +bottom_solid_layers = 4 bridge_acceleration = 0 bridge_flow_ratio = 1 -bridge_speed = 0 -brim_width = 0 +bridge_speed = 60 +brim_width = 2 complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 -external_perimeter_speed = 0 +external_perimeter_speed = 30 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0 fill_angle = 45 -fill_density = 15% +fill_density = 20% fill_pattern = rectilinear first_layer_acceleration = 0 -first_layer_extrusion_width = 150% +first_layer_extrusion_width = 0 first_layer_height = 0.2 first_layer_speed = 20 -gap_fill_speed = 0 +gap_fill_speed = 20 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 -infill_extrusion_width = 0 +infill_extrusion_width = 1.1 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 15% -infill_speed = 0 +infill_speed = 60 interface_shells = 0 layer_height = 0.2 -max_print_speed = 50 +max_print_speed = 130 max_volumetric_speed = 0 min_skirt_length = 1 notes = @@ -371,58 +251,58 @@ overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 -perimeter_speed = 0 -perimeters = 2 +perimeter_speed = 60 +perimeters = 3 post_process = raft_layers = 0 resolution = 0 seam_position = aligned -skirt_distance = 1 +skirt_distance = 6 skirt_height = 1 skirts = 1 -small_perimeter_speed = 0 +small_perimeter_speed = 15 solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0 -solid_infill_speed = 0 +solid_infill_speed = 10 spiral_vase = 0 standby_temperature_delta = -5 -support_material = 0 +support_material = 1 support_material_angle = 0 -support_material_contact_distance = 0.2 +support_material_contact_distance = 0.4 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_extruder = 1 -support_material_interface_layers = 2 +support_material_interface_layers = 3 support_material_interface_spacing = 0 -support_material_interface_speed = 100% -support_material_pattern = rectilinear -support_material_spacing = 5 -support_material_speed = 0 -support_material_threshold = 40 -thin_walls = 1 +support_material_interface_speed = 30 +support_material_pattern = rectilinear-grid +support_material_spacing = 2 +support_material_speed = 60 +support_material_threshold = 0 +thin_walls = 0 threads = 2 top_infill_extrusion_width = 0 -top_solid_infill_speed = 0 -top_solid_layers = 3 -travel_speed = 100 +top_solid_infill_speed = 5 +top_solid_layers = 5 +travel_speed = 130 xy_size_compensation = 0 -[print:prusa i3 100] -avoid_crossing_perimeters = 0 -bottom_solid_layers = 3 +[print:MendelPro] +avoid_crossing_perimeters = 1 +bottom_solid_layers = 5 bridge_acceleration = 0 bridge_flow_ratio = 1 bridge_speed = 40 -brim_width = 0 +brim_width = 2 complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 -external_perimeter_speed = 10 +external_perimeter_speed = 30 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 @@ -434,22 +314,22 @@ fill_pattern = rectilinear first_layer_acceleration = 0 first_layer_extrusion_width = 0 first_layer_height = 0.2 -first_layer_speed = 10 -gap_fill_speed = 10 +first_layer_speed = 30 +gap_fill_speed = 20 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 -infill_extrusion_width = 110% +infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 -infill_overlap = 15% -infill_speed = 0 +infill_overlap = 25% +infill_speed = 50 interface_shells = 0 -layer_height = 0.1 +layer_height = 0.2 max_print_speed = 80 max_volumetric_speed = 0 -min_skirt_length = 1 +min_skirt_length = 6 notes = only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 @@ -458,48 +338,48 @@ overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 -perimeter_speed = 0 +perimeter_speed = 50 perimeters = 3 post_process = raft_layers = 0 resolution = 0 -seam_position = aligned +seam_position = nearest skirt_distance = 6 skirt_height = 1 -skirts = 3 -small_perimeter_speed = 10 +skirts = 1 +small_perimeter_speed = 20 solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0 -solid_infill_speed = 0 +solid_infill_speed = 40 spiral_vase = 0 standby_temperature_delta = -5 -support_material = 0 +support_material = 1 support_material_angle = 0 -support_material_contact_distance = 0.2 +support_material_contact_distance = 0.4 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_extruder = 1 -support_material_interface_layers = 2 +support_material_interface_layers = 3 support_material_interface_spacing = 0 -support_material_interface_speed = 100% +support_material_interface_speed = 40 support_material_pattern = rectilinear -support_material_spacing = 5 -support_material_speed = 0 -support_material_threshold = 40 +support_material_spacing = 3 +support_material_speed = 50 +support_material_threshold = 0 thin_walls = 1 threads = 2 top_infill_extrusion_width = 0 -top_solid_infill_speed = 10 -top_solid_layers = 3 +top_solid_infill_speed = 40 +top_solid_layers = 5 travel_speed = 100 xy_size_compensation = 0 -[print:prusa i3 100 testtesttest] +[print:TinyBoy] avoid_crossing_perimeters = 0 -bottom_solid_layers = 0 +bottom_solid_layers = 3 bridge_acceleration = 0 bridge_flow_ratio = 1 bridge_speed = 40 @@ -509,31 +389,31 @@ default_acceleration = 0 dont_support_bridges = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 -external_perimeter_speed = 10 +external_perimeter_speed = 20 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0 fill_angle = 45 -fill_density = 0% -fill_pattern = rectilinear +fill_density = 20% +fill_pattern = 3dhoneycomb first_layer_acceleration = 0 first_layer_extrusion_width = 0 first_layer_height = 0.2 first_layer_speed = 10 -gap_fill_speed = 10 +gap_fill_speed = 20 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 -infill_extrusion_width = 110% +infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 15% infill_speed = 0 interface_shells = 0 -layer_height = 0.1 +layer_height = 0.2 max_print_speed = 80 max_volumetric_speed = 0 min_skirt_length = 1 @@ -546,15 +426,15 @@ perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 0 -perimeters = 1 +perimeters = 2 post_process = raft_layers = 0 resolution = 0 -seam_position = aligned +seam_position = nearest skirt_distance = 1 skirt_height = 1 skirts = 1 -small_perimeter_speed = 10 +small_perimeter_speed = 0 solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extruder = 1 @@ -579,49 +459,49 @@ support_material_threshold = 40 thin_walls = 1 threads = 2 top_infill_extrusion_width = 0 -top_solid_infill_speed = 10 -top_solid_layers = 0 +top_solid_infill_speed = 20 +top_solid_layers = 4 travel_speed = 100 xy_size_compensation = 0 -[print:prusa i3 250] +[print:Toy] avoid_crossing_perimeters = 0 -bottom_solid_layers = 3 +bottom_solid_layers = 2 bridge_acceleration = 0 bridge_flow_ratio = 1 -bridge_speed = 40 +bridge_speed = 0 brim_width = 0 complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 -external_perimeter_speed = 10 +external_perimeter_speed = 0 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0 fill_angle = 45 -fill_density = 20% +fill_density = 0% fill_pattern = rectilinear first_layer_acceleration = 0 first_layer_extrusion_width = 0 first_layer_height = 0.2 -first_layer_speed = 15 -gap_fill_speed = 10 +first_layer_speed = 10 +gap_fill_speed = 0 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 -infill_extrusion_width = 110% +infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 15% infill_speed = 0 interface_shells = 0 -layer_height = 0.25 -max_print_speed = 60 +layer_height = 0.2 +max_print_speed = 10 max_volumetric_speed = 0 min_skirt_length = 1 notes = @@ -641,7 +521,7 @@ seam_position = aligned skirt_distance = 1 skirt_height = 1 skirts = 1 -small_perimeter_speed = 10 +small_perimeter_speed = 0 solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extruder = 1 @@ -649,14 +529,14 @@ solid_infill_extrusion_width = 0 solid_infill_speed = 0 spiral_vase = 0 standby_temperature_delta = -5 -support_material = 0 +support_material = 1 support_material_angle = 0 -support_material_contact_distance = 0.2 +support_material_contact_distance = 0.3 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_extruder = 1 -support_material_interface_layers = 2 +support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = rectilinear @@ -666,24 +546,24 @@ support_material_threshold = 40 thin_walls = 1 threads = 2 top_infill_extrusion_width = 0 -top_solid_infill_speed = 20 -top_solid_layers = 3 +top_solid_infill_speed = 0 +top_solid_layers = 0 travel_speed = 100 xy_size_compensation = 0 -[print:prusa i3 400] +[print:prusa i3] avoid_crossing_perimeters = 0 -bottom_solid_layers = 3 +bottom_solid_layers = 4 bridge_acceleration = 0 bridge_flow_ratio = 1 -bridge_speed = 60 +bridge_speed = 40 brim_width = 0 complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 -external_perimeter_speed = 20 +external_perimeter_speed = 30 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 @@ -691,26 +571,26 @@ extruder_clearance_radius = 20 extrusion_width = 0 fill_angle = 45 fill_density = 20% -fill_pattern = rectilinear +fill_pattern = honeycomb first_layer_acceleration = 0 first_layer_extrusion_width = 0 -first_layer_height = 0.2 +first_layer_height = 0.3 first_layer_speed = 10 -gap_fill_speed = 10 +gap_fill_speed = 20 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 -infill_extrusion_width = 110% +infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 15% -infill_speed = 0 +infill_speed = 80 interface_shells = 0 -layer_height = 0.4 -max_print_speed = 80 +layer_height = 0.15 +max_print_speed = 100 max_volumetric_speed = 0 -min_skirt_length = 1 +min_skirt_length = 3 notes = only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 @@ -719,58 +599,58 @@ overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 -perimeter_speed = 0 -perimeters = 2 +perimeter_speed = 60 +perimeters = 3 post_process = raft_layers = 0 resolution = 0 -seam_position = aligned -skirt_distance = 1 +seam_position = nearest +skirt_distance = 6 skirt_height = 1 skirts = 1 -small_perimeter_speed = 10 +small_perimeter_speed = 15 solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0 -solid_infill_speed = 0 +solid_infill_speed = 40 spiral_vase = 0 standby_temperature_delta = -5 -support_material = 0 +support_material = 1 support_material_angle = 0 -support_material_contact_distance = 0.2 +support_material_contact_distance = 0.3 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_extruder = 1 -support_material_interface_layers = 2 +support_material_interface_layers = 3 support_material_interface_spacing = 0 -support_material_interface_speed = 100% +support_material_interface_speed = 40 support_material_pattern = rectilinear -support_material_spacing = 5 -support_material_speed = 0 -support_material_threshold = 40 +support_material_spacing = 3 +support_material_speed = 40 +support_material_threshold = 0 thin_walls = 1 threads = 2 top_infill_extrusion_width = 0 -top_solid_infill_speed = 20 -top_solid_layers = 3 +top_solid_infill_speed = 30 +top_solid_layers = 4 travel_speed = 100 xy_size_compensation = 0 -[print:prusa i3 400 sup] +[print:prusa i3 test] avoid_crossing_perimeters = 0 -bottom_solid_layers = 3 +bottom_solid_layers = 4 bridge_acceleration = 0 bridge_flow_ratio = 1 bridge_speed = 40 -brim_width = 0 +brim_width = 5 complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 -external_perimeter_speed = 10 +external_perimeter_speed = 30 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 @@ -778,26 +658,26 @@ extruder_clearance_radius = 20 extrusion_width = 0 fill_angle = 45 fill_density = 20% -fill_pattern = rectilinear +fill_pattern = honeycomb first_layer_acceleration = 0 first_layer_extrusion_width = 0 first_layer_height = 0.2 first_layer_speed = 10 -gap_fill_speed = 10 +gap_fill_speed = 20 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 -infill_extrusion_width = 110% +infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 15% -infill_speed = 0 +infill_speed = 80 interface_shells = 0 -layer_height = 0.4 -max_print_speed = 80 +layer_height = 0.2 +max_print_speed = 100 max_volumetric_speed = 0 -min_skirt_length = 1 +min_skirt_length = 3 notes = only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 @@ -806,49 +686,49 @@ overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 -perimeter_speed = 0 -perimeters = 2 +perimeter_speed = 60 +perimeters = 3 post_process = raft_layers = 0 resolution = 0 -seam_position = aligned -skirt_distance = 1 +seam_position = nearest +skirt_distance = 6 skirt_height = 1 skirts = 1 -small_perimeter_speed = 10 +small_perimeter_speed = 15 solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0 -solid_infill_speed = 0 +solid_infill_speed = 40 spiral_vase = 0 standby_temperature_delta = -5 support_material = 1 support_material_angle = 0 -support_material_contact_distance = 0.2 +support_material_contact_distance = 0 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_extruder = 1 -support_material_interface_layers = 2 +support_material_interface_layers = 3 support_material_interface_spacing = 0 -support_material_interface_speed = 100% -support_material_pattern = rectilinear -support_material_spacing = 5 -support_material_speed = 0 -support_material_threshold = 40 +support_material_interface_speed = 40 +support_material_pattern = pillars +support_material_spacing = 3 +support_material_speed = 40 +support_material_threshold = 0 thin_walls = 1 threads = 2 top_infill_extrusion_width = 0 -top_solid_infill_speed = 20 -top_solid_layers = 3 +top_solid_infill_speed = 30 +top_solid_layers = 4 travel_speed = 100 xy_size_compensation = 0 -[printer:LULZBOT ABS fine] +[printer:Lulzbot] bed_shape = 0x0,298x0,298x275,0x275 before_layer_gcode = -end_gcode = M104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200 ;\nG28 X0 ; home X axis\nM84 ; disable motors +end_gcode = M104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200 ;\nG28 X0 ; home X axis\nM84 ; disable motors\n\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\n extruder_offset = 0x0 gcode_flavor = reprap layer_gcode = @@ -858,13 +738,13 @@ octoprint_host = pressure_advance = 0 retract_before_travel = 2 retract_layer_change = 1 -retract_length = 1.75 +retract_length = 3 retract_length_toolchange = 3 retract_lift = 0 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 -retract_speed = 20 -start_gcode = G28 ; home all axes +retract_speed = 40 +start_gcode = G28 ; home all axes\n toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 0 @@ -876,7 +756,7 @@ z_offset = 0 [printer:MendelPro] bed_shape = 0x0,220x0,220x177,0x177 before_layer_gcode = -end_gcode = M104 S0 ; turn off temperature\nM140 S0;\nG28 X0 ; home X axis\nM84 ; disable motors\n +end_gcode = M104 S0 ; turn off temperature\nM140 S0;\nG28 X0 ; home X axis\nG0 Y177;\nM84 ; disable motors\n extruder_offset = 0x0 gcode_flavor = reprap layer_gcode = @@ -892,7 +772,7 @@ retract_lift = 0 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 40 -start_gcode = G28 Z ; home Z\nG28 X Y ; home X Y\n +start_gcode = G28 Z ; home Z\nG28 X Y ; home X Y\nG0 Y40 ; clab move\n toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 0 @@ -929,10 +809,38 @@ vibration_limit = 0 wipe = 0 z_offset = 0 +[printer:Toyrep] +bed_shape = 0x0,125x0,125x125,0x125 +before_layer_gcode = +end_gcode = M104 S0 ; turn off nozzle temperature\nM84 ; disable motors +extruder_offset = 0x0 +gcode_flavor = reprap +layer_gcode = +nozzle_diameter = 0.4 +octoprint_apikey = +octoprint_host = +pressure_advance = 0 +retract_before_travel = 2 +retract_layer_change = 1 +retract_length = 0 +retract_length_toolchange = 3 +retract_lift = 0 +retract_restart_extra = 0 +retract_restart_extra_toolchange = 0 +retract_speed = 10 +start_gcode = \n +toolchange_gcode = +use_firmware_retraction = 0 +use_relative_e_distances = 0 +use_volumetric_e = 0 +vibration_limit = 0 +wipe = 0 +z_offset = 0 + [printer:prusa i3] -bed_shape = 0x0,190x0,190x190,0x190 +bed_shape = 0x0,190x0,190x220,0x220 before_layer_gcode = -end_gcode = M104 S0 ; turn off temperature\nM140 S0 ; turn off bed temp \nG28 X0 ; home X axis\nG0 Y190 ; präsent object\nM84 ; disable motors\n\n +end_gcode = M104 S0 ; turn off temperature\nM140 S0 ; turn off bed temp \nG28 X0 ; home X axis\nG0 Y190 ; präsent object\nM84 ; disable motors\nM81 ; Power off\n\n extruder_offset = 0x0 gcode_flavor = reprap layer_gcode = @@ -941,15 +849,15 @@ octoprint_apikey = 176444E92BFF48819CE0D8F1B264A91C octoprint_host = pressure_advance = 0 retract_before_travel = 2 -retract_layer_change = 1 -retract_length = 5 +retract_layer_change = 0 +retract_length = 2 retract_length_toolchange = 10 retract_lift = 0 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 40 -start_gcode = G28 Z ; home Z\n\nG28 X Y ; home X Y\n -toolchange_gcode = +start_gcode = G28 Z ; home Z\n;G0 Z1 ; lift Z\nG28 X Y ; home X Y\nG0 Y40 ; clab move +toolchange_gcode = M83 ; turn on relative movement for extruder \nG1 E-5 ; retract filament 5mm \nG1 X10 Y10 Z4.000000 ; home X and Y axis leave Z at current height \nM84 E ; release extruder stepper motor from 'holding' position \n@pause ; pause print! \nG1 E0 ; reset extruder, ready to push out plastic again \nM82 ; set extruder movement back to absolute ready for next layer use_firmware_retraction = 0 use_relative_e_distances = 0 use_volumetric_e = 0