X-Git-Url: https://git.rohieb.name/stratum0-wiki.git/blobdiff_plain/e2d7258fbd1e49faa7ea724c101a88b5b395111d..2b07a0850de3b4ae543b1f16951ded9686b491b9:/3D-Drucker%2FSlicerBundle.ini.mw?ds=sidebyside diff --git a/3D-Drucker%2FSlicerBundle.ini.mw b/3D-Drucker%2FSlicerBundle.ini.mw index 89f4e038c..5e4db814a 100644 --- a/3D-Drucker%2FSlicerBundle.ini.mw +++ b/3D-Drucker%2FSlicerBundle.ini.mw @@ -1,179 +1,36 @@ -# generated by Slic3r 1.2.9 on Mon Nov 21 19:45:57 2016 +# generated by Slic3r Prusa Edition 1.38.5-prusa3d-win64 on 2018-01-16 at 20:47:39 -[filament:1.75mm ABS] -bed_temperature = 0 -bridge_fan_speed = 50 -cooling = 1 -disable_fan_first_layers = 1 -extrusion_multiplier = 1 -fan_always_on = 0 -fan_below_layer_time = 60 -filament_colour = #FFFFFF -filament_diameter = 1.75 -first_layer_bed_temperature = 0 -first_layer_temperature = 240 -max_fan_speed = 0 -min_fan_speed = 0 -min_print_speed = 5 -slowdown_below_layer_time = 30 -temperature = 230 - -[filament:1.75mm Holz] -bed_temperature = 50 -bridge_fan_speed = 100 -cooling = 1 -disable_fan_first_layers = 1 -extrusion_multiplier = 1 -fan_always_on = 1 -fan_below_layer_time = 60 -filament_colour = #FFFFFF -filament_diameter = 1.75 -first_layer_bed_temperature = 50 -first_layer_temperature = 200 -max_fan_speed = 100 -min_fan_speed = 50 -min_print_speed = 5 -slowdown_below_layer_time = 30 -temperature = 190 - -[filament:1.75mm PLA] -bed_temperature = 50 -bridge_fan_speed = 100 -cooling = 1 -disable_fan_first_layers = 1 -extrusion_multiplier = 1 -fan_always_on = 1 -fan_below_layer_time = 60 -filament_colour = #FFFFFF -filament_diameter = 1.75 -first_layer_bed_temperature = 50 -first_layer_temperature = 200 -max_fan_speed = 100 -min_fan_speed = 50 -min_print_speed = 5 -slowdown_below_layer_time = 15 -temperature = 185 - -[filament:1.75mm PLA TinyBoy] -bed_temperature = 0 -bridge_fan_speed = 100 -cooling = 1 -disable_fan_first_layers = 2 -extrusion_multiplier = 1 -fan_always_on = 1 -fan_below_layer_time = 60 -filament_colour = #FF8000 -filament_diameter = 1.75 -first_layer_bed_temperature = 0 -first_layer_temperature = 200 -max_fan_speed = 40 -min_fan_speed = 35 -min_print_speed = 5 -slowdown_below_layer_time = 15 -temperature = 190 - -[filament:2.85mm ABS] -bed_temperature = 100 -bridge_fan_speed = 50 -cooling = 1 -disable_fan_first_layers = 1 -extrusion_multiplier = 1 -fan_always_on = 0 -fan_below_layer_time = 60 -filament_colour = #FFFFFF -filament_diameter = 2.85 -first_layer_bed_temperature = 100 -first_layer_temperature = 250 -max_fan_speed = 0 -min_fan_speed = 0 -min_print_speed = 5 -slowdown_below_layer_time = 20 -temperature = 230 - -[filament:2.85mm PETG ] -bed_temperature = 75 -bridge_fan_speed = 100 -cooling = 1 -disable_fan_first_layers = 1 -extrusion_multiplier = 1 -fan_always_on = 1 -fan_below_layer_time = 60 -filament_colour = #B1EB96 -filament_diameter = 2.85 -first_layer_bed_temperature = 75 -first_layer_temperature = 235 -max_fan_speed = 100 -min_fan_speed = 50 -min_print_speed = 10 -slowdown_below_layer_time = 30 -temperature = 235 - -[filament:2.85mm PLA] -bed_temperature = 50 -bridge_fan_speed = 100 -cooling = 1 -disable_fan_first_layers = 1 -extrusion_multiplier = 1 -fan_always_on = 1 -fan_below_layer_time = 60 -filament_colour = #FF00FF -filament_diameter = 2.85 -first_layer_bed_temperature = 50 -first_layer_temperature = 200 -max_fan_speed = 100 -min_fan_speed = 35 -min_print_speed = 10 -slowdown_below_layer_time = 10 -temperature = 185 - -[filament:2.85mm Willowflex] -bed_temperature = 70 -bridge_fan_speed = 100 -cooling = 1 -disable_fan_first_layers = 1 -extrusion_multiplier = 1 -fan_always_on = 1 -fan_below_layer_time = 60 -filament_colour = #BF0005 -filament_diameter = 2.85 -first_layer_bed_temperature = 70 -first_layer_temperature = 160 -max_fan_speed = 100 -min_fan_speed = 35 -min_print_speed = 10 -slowdown_below_layer_time = 10 -temperature = 160 - -[presets] -filament = 2.85mm Willowflex.ini -print = prusa i3.ini -printer = prusa i3.ini - -[print:Lulzbot] -avoid_crossing_perimeters = 0 -bottom_solid_layers = 4 +[print:Kossel print] +avoid_crossing_perimeters = 1 +bottom_solid_layers = 3 bridge_acceleration = 0 +bridge_angle = 0 bridge_flow_ratio = 1 bridge_speed = 60 -brim_width = 1 +brim_width = 0 +clip_multipart_objects = 0 +compatible_printers = +compatible_printers_condition = complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 +elefant_foot_compensation = 0 +ensure_vertical_shell_thickness = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 -external_perimeter_speed = 40 +external_perimeter_speed = 30 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0 -fill_angle = 35 +fill_angle = 45 fill_density = 20% -fill_pattern = rectilinear +fill_pattern = cubic first_layer_acceleration = 0 -first_layer_extrusion_width = 0 +first_layer_extrusion_width = 200% first_layer_height = 0.2 -first_layer_speed = 10 +first_layer_speed = 30 gap_fill_speed = 20 gcode_comments = 0 infill_acceleration = 0 @@ -182,13 +39,15 @@ infill_extruder = 1 infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 -infill_overlap = 15% +infill_overlap = 25% infill_speed = 80 interface_shells = 0 layer_height = 0.2 -max_print_speed = 100 +max_print_speed = 80 +max_volumetric_extrusion_rate_slope_negative = 0 +max_volumetric_extrusion_rate_slope_positive = 0 max_volumetric_speed = 0 -min_skirt_length = 3 +min_skirt_length = 0 notes = only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 @@ -197,145 +56,180 @@ overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 -perimeter_speed = 80 +perimeter_speed = 60 perimeters = 3 post_process = raft_layers = 0 resolution = 0 -seam_position = nearest +seam_position = aligned skirt_distance = 6 skirt_height = 1 -skirts = 1 +skirts = 3 small_perimeter_speed = 15 -solid_infill_below_area = 30 +solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0 -solid_infill_speed = 60 +solid_infill_speed = 20 spiral_vase = 0 standby_temperature_delta = -5 support_material = 0 support_material_angle = 0 -support_material_contact_distance = 0.2 +support_material_buildplate_only = 0 +support_material_contact_distance = 0.4 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 +support_material_interface_contact_loops = 0 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 -support_material_interface_speed = 40 -support_material_pattern = rectilinear +support_material_interface_speed = 100% +support_material_pattern = pillars support_material_spacing = 2.5 support_material_speed = 60 -support_material_threshold = 0 +support_material_synchronize_layers = 0 +support_material_threshold = 40 +support_material_with_sheath = 1 +support_material_xy_spacing = 0.6 thin_walls = 1 threads = 2 top_infill_extrusion_width = 0 -top_solid_infill_speed = 40 -top_solid_layers = 4 +top_solid_infill_speed = 15 +top_solid_layers = 3 travel_speed = 130 +wipe_tower = 1 +wipe_tower_per_color_wipe = 10 +wipe_tower_width = 10 +wipe_tower_x = 0 +wipe_tower_y = 65 xy_size_compensation = 0 -[print:MendelPro] -avoid_crossing_perimeters = 0 -bottom_solid_layers = 4 -bridge_acceleration = 0 +[print:Lulzbot print] +avoid_crossing_perimeters = 1 +bottom_solid_layers = 3 +bridge_acceleration = 2000 +bridge_angle = 0 bridge_flow_ratio = 1 -bridge_speed = 40 -brim_width = 1 +bridge_speed = 72 +brim_width = 0 +clip_multipart_objects = 0 +compatible_printers = +compatible_printers_condition = complete_objects = 0 -default_acceleration = 0 +default_acceleration = 2000 dont_support_bridges = 1 +elefant_foot_compensation = 0 +ensure_vertical_shell_thickness = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 -external_perimeter_speed = 30 +external_perimeter_speed = 45 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 -extrusion_width = 0 +extrusion_width = 0.42 fill_angle = 45 fill_density = 20% -fill_pattern = rectilinear -first_layer_acceleration = 0 -first_layer_extrusion_width = 0 -first_layer_height = 0.2 +fill_pattern = cubic +first_layer_acceleration = 2000 +first_layer_extrusion_width = 0.53 +first_layer_height = 100% first_layer_speed = 10 -gap_fill_speed = 10 +gap_fill_speed = 55 gcode_comments = 0 -infill_acceleration = 0 +infill_acceleration = 2000 infill_every_layers = 1 infill_extruder = 1 -infill_extrusion_width = 0 +infill_extrusion_width = 0.68 infill_first = 0 infill_only_where_needed = 0 -infill_overlap = 15% -infill_speed = 0 +infill_overlap = 55% +infill_speed = 80 interface_shells = 0 layer_height = 0.2 max_print_speed = 80 +max_volumetric_extrusion_rate_slope_negative = 0 +max_volumetric_extrusion_rate_slope_positive = 0 max_volumetric_speed = 0 -min_skirt_length = 2 +min_skirt_length = 0 notes = -only_retract_when_crossing_perimeters = 1 +only_retract_when_crossing_perimeters = 0 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 -perimeter_acceleration = 0 +perimeter_acceleration = 1200 perimeter_extruder = 1 -perimeter_extrusion_width = 0 -perimeter_speed = 0 -perimeters = 2 +perimeter_extrusion_width = 0.38 +perimeter_speed = 75 +perimeters = 3 post_process = +print_settings_id = raft_layers = 0 resolution = 0 -seam_position = nearest -skirt_distance = 10 +seam_position = aligned +skirt_distance = 5 skirt_height = 1 -skirts = 1 -small_perimeter_speed = 10 -solid_infill_below_area = 70 +skirts = 3 +small_perimeter_speed = 50 +solid_infill_below_area = 90 solid_infill_every_layers = 0 solid_infill_extruder = 1 -solid_infill_extrusion_width = 0 -solid_infill_speed = 0 +solid_infill_extrusion_width = 0.5 +solid_infill_speed = 75 spiral_vase = 0 standby_temperature_delta = -5 -support_material = 1 +support_material = 0 support_material_angle = 0 -support_material_contact_distance = 0.4 +support_material_buildplate_only = 0 +support_material_contact_distance = 0.3 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 +support_material_interface_contact_loops = 0 support_material_interface_extruder = 1 -support_material_interface_layers = 3 +support_material_interface_layers = 5 support_material_interface_spacing = 0 support_material_interface_speed = 100% -support_material_pattern = pillars -support_material_spacing = 3 +support_material_pattern = rectilinear-grid +support_material_spacing = 7 support_material_speed = 60 -support_material_threshold = 0 +support_material_synchronize_layers = 0 +support_material_threshold = 30 +support_material_with_sheath = 0 +support_material_xy_spacing = 0.5 thin_walls = 1 threads = 2 -top_infill_extrusion_width = 0 -top_solid_infill_speed = 20 -top_solid_layers = 4 -travel_speed = 100 +top_infill_extrusion_width = 0.4 +top_solid_infill_speed = 60 +top_solid_layers = 3 +travel_speed = 160 +wipe_tower = 0 +wipe_tower_per_color_wipe = 15 +wipe_tower_width = 60 +wipe_tower_x = 180 +wipe_tower_y = 140 xy_size_compensation = 0 -[print:TinyBoy] +[print:Mendel print] avoid_crossing_perimeters = 0 bottom_solid_layers = 3 bridge_acceleration = 0 +bridge_angle = 0 bridge_flow_ratio = 1 bridge_speed = 40 -brim_width = 0 +brim_width = 2 +clip_multipart_objects = 0 +compatible_printers = +compatible_printers_condition = complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 +elefant_foot_compensation = 0 +ensure_vertical_shell_thickness = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 -external_perimeter_speed = 20 +external_perimeter_speed = 30 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 @@ -343,11 +237,11 @@ extruder_clearance_radius = 20 extrusion_width = 0 fill_angle = 45 fill_density = 20% -fill_pattern = 3dhoneycomb +fill_pattern = cubic first_layer_acceleration = 0 -first_layer_extrusion_width = 0 +first_layer_extrusion_width = 150% first_layer_height = 0.2 -first_layer_speed = 10 +first_layer_speed = 20 gap_fill_speed = 20 gcode_comments = 0 infill_acceleration = 0 @@ -357,12 +251,14 @@ infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 15% -infill_speed = 0 +infill_speed = 40 interface_shells = 0 layer_height = 0.2 -max_print_speed = 80 +max_print_speed = 40 +max_volumetric_extrusion_rate_slope_negative = 0 +max_volumetric_extrusion_rate_slope_positive = 0 max_volumetric_speed = 0 -min_skirt_length = 1 +min_skirt_length = 0 notes = only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 @@ -371,142 +267,72 @@ overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 -perimeter_speed = 0 -perimeters = 2 +perimeter_speed = 40 +perimeters = 3 post_process = +print_settings_id = raft_layers = 0 resolution = 0 -seam_position = nearest -skirt_distance = 1 +seam_position = aligned +skirt_distance = 6 skirt_height = 1 -skirts = 1 -small_perimeter_speed = 0 +skirts = 3 +small_perimeter_speed = 15 solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0 -solid_infill_speed = 0 +solid_infill_speed = 20 spiral_vase = 0 standby_temperature_delta = -5 -support_material = 0 +support_material = 1 support_material_angle = 0 +support_material_buildplate_only = 0 support_material_contact_distance = 0.2 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 +support_material_interface_contact_loops = 0 support_material_interface_extruder = 1 -support_material_interface_layers = 2 +support_material_interface_layers = 3 support_material_interface_spacing = 0 -support_material_interface_speed = 100% -support_material_pattern = rectilinear -support_material_spacing = 5 -support_material_speed = 0 -support_material_threshold = 40 +support_material_interface_speed = 30 +support_material_pattern = pillars +support_material_spacing = 2.5 +support_material_speed = 40 +support_material_synchronize_layers = 0 +support_material_threshold = 0 +support_material_with_sheath = 1 +support_material_xy_spacing = 50% thin_walls = 1 threads = 2 top_infill_extrusion_width = 0 -top_solid_infill_speed = 20 +top_solid_infill_speed = 15 top_solid_layers = 4 -travel_speed = 100 +travel_speed = 60 +wipe_tower = 0 +wipe_tower_per_color_wipe = 15 +wipe_tower_width = 60 +wipe_tower_x = 180 +wipe_tower_y = 140 xy_size_compensation = 0 -[print:Toy] -avoid_crossing_perimeters = 0 +[print:Tiny print] +avoid_crossing_perimeters = 1 bottom_solid_layers = 2 bridge_acceleration = 0 +bridge_angle = 0 bridge_flow_ratio = 1 -bridge_speed = 0 -brim_width = 0 +bridge_speed = 60 +brim_width = 2 +clip_multipart_objects = 0 +compatible_printers = +compatible_printers_condition = complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 -external_fill_pattern = rectilinear -external_perimeter_extrusion_width = 0 -external_perimeter_speed = 0 -external_perimeters_first = 0 -extra_perimeters = 1 -extruder_clearance_height = 20 -extruder_clearance_radius = 20 -extrusion_width = 0 -fill_angle = 45 -fill_density = 0% -fill_pattern = rectilinear -first_layer_acceleration = 0 -first_layer_extrusion_width = 0 -first_layer_height = 0.2 -first_layer_speed = 10 -gap_fill_speed = 0 -gcode_comments = 0 -infill_acceleration = 0 -infill_every_layers = 1 -infill_extruder = 1 -infill_extrusion_width = 0 -infill_first = 0 -infill_only_where_needed = 0 -infill_overlap = 15% -infill_speed = 0 -interface_shells = 0 -layer_height = 0.2 -max_print_speed = 10 -max_volumetric_speed = 0 -min_skirt_length = 1 -notes = -only_retract_when_crossing_perimeters = 1 -ooze_prevention = 0 -output_filename_format = [input_filename_base].gcode -overhangs = 1 -perimeter_acceleration = 0 -perimeter_extruder = 1 -perimeter_extrusion_width = 0 -perimeter_speed = 0 -perimeters = 2 -post_process = -raft_layers = 0 -resolution = 0 -seam_position = aligned -skirt_distance = 1 -skirt_height = 1 -skirts = 1 -small_perimeter_speed = 0 -solid_infill_below_area = 70 -solid_infill_every_layers = 0 -solid_infill_extruder = 1 -solid_infill_extrusion_width = 0 -solid_infill_speed = 0 -spiral_vase = 0 -standby_temperature_delta = -5 -support_material = 1 -support_material_angle = 0 -support_material_contact_distance = 0.3 -support_material_enforce_layers = 0 -support_material_extruder = 1 -support_material_extrusion_width = 0 -support_material_interface_extruder = 1 -support_material_interface_layers = 3 -support_material_interface_spacing = 0 -support_material_interface_speed = 100% -support_material_pattern = rectilinear -support_material_spacing = 5 -support_material_speed = 0 -support_material_threshold = 40 -thin_walls = 1 -threads = 2 -top_infill_extrusion_width = 0 -top_solid_infill_speed = 0 -top_solid_layers = 0 -travel_speed = 100 -xy_size_compensation = 0 - -[print:prusa i3] -avoid_crossing_perimeters = 0 -bottom_solid_layers = 4 -bridge_acceleration = 0 -bridge_flow_ratio = 1 -bridge_speed = 40 -brim_width = 0 -complete_objects = 0 -default_acceleration = 1000 -dont_support_bridges = 1 +elefant_foot_compensation = 0 +ensure_vertical_shell_thickness = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 external_perimeter_speed = 30 @@ -516,12 +342,12 @@ extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0 fill_angle = 45 -fill_density = 20% +fill_density = 10% fill_pattern = rectilinear first_layer_acceleration = 0 -first_layer_extrusion_width = 0 +first_layer_extrusion_width = 120% first_layer_height = 0.2 -first_layer_speed = 10 +first_layer_speed = 20 gap_fill_speed = 20 gcode_comments = 0 infill_acceleration = 0 @@ -535,8 +361,10 @@ infill_speed = 80 interface_shells = 0 layer_height = 0.2 max_print_speed = 100 +max_volumetric_extrusion_rate_slope_negative = 0 +max_volumetric_extrusion_rate_slope_positive = 0 max_volumetric_speed = 0 -min_skirt_length = 3 +min_skirt_length = 0 notes = only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 @@ -546,184 +374,429 @@ perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 60 -perimeters = 3 +perimeters = 2 post_process = +print_settings_id = raft_layers = 0 resolution = 0 seam_position = nearest skirt_distance = 6 skirt_height = 1 -skirts = 1 +skirts = 3 small_perimeter_speed = 15 solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0 -solid_infill_speed = 60 +solid_infill_speed = 20 spiral_vase = 0 standby_temperature_delta = -5 support_material = 1 support_material_angle = 0 +support_material_buildplate_only = 1 support_material_contact_distance = 0.2 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 +support_material_interface_contact_loops = 0 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 -support_material_interface_speed = 75% +support_material_interface_speed = 30 support_material_pattern = pillars support_material_spacing = 2.5 support_material_speed = 60 -support_material_threshold = 0 +support_material_synchronize_layers = 1 +support_material_threshold = 40 +support_material_with_sheath = 1 +support_material_xy_spacing = 0.4 thin_walls = 1 threads = 2 top_infill_extrusion_width = 0 -top_solid_infill_speed = 30 -top_solid_layers = 4 -travel_speed = 100 +top_solid_infill_speed = 15 +top_solid_layers = 3 +travel_speed = 130 +wipe_tower = 0 +wipe_tower_per_color_wipe = 15 +wipe_tower_width = 60 +wipe_tower_x = 180 +wipe_tower_y = 140 xy_size_compensation = 0 -[printer:Lulzbot] -bed_shape = 0x0,298x0,298x275,0x275 +[filament:ABS 175] +bed_temperature = 0 +bridge_fan_speed = 100 +compatible_printers = +compatible_printers_condition = +cooling = 0 +disable_fan_first_layers = 3 +end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" +extrusion_multiplier = 1 +fan_always_on = 0 +fan_below_layer_time = 60 +filament_colour = #FFFFFF +filament_cost = 0 +filament_density = 0 +filament_diameter = 1.75 +filament_max_volumetric_speed = 0 +filament_notes = "" +filament_settings_id = +filament_soluble = 0 +filament_type = PLA +first_layer_bed_temperature = 0 +first_layer_temperature = 245 +max_fan_speed = 100 +min_fan_speed = 100 +min_print_speed = 5 +slowdown_below_layer_time = 20 +start_filament_gcode = "; Filament gcode\n" +temperature = 235 + +[filament:PETG 175] +bed_temperature = 0 +bridge_fan_speed = 100 +compatible_printers = +compatible_printers_condition = +cooling = 0 +disable_fan_first_layers = 5 +end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" +extrusion_multiplier = 1 +fan_always_on = 1 +fan_below_layer_time = 60 +filament_colour = #FFFFFF +filament_cost = 27.4375 +filament_density = 1.27 +filament_diameter = 1.75 +filament_max_volumetric_speed = 0 +filament_notes = "" +filament_settings_id = +filament_soluble = 0 +filament_type = PET +first_layer_bed_temperature = 0 +first_layer_temperature = 245 +max_fan_speed = 100 +min_fan_speed = 100 +min_print_speed = 5 +slowdown_below_layer_time = 20 +start_filament_gcode = "; Filament gcode\n" +temperature = 220 + +[filament:PETG 285] +bed_temperature = 75 +bridge_fan_speed = 100 +compatible_printers = +compatible_printers_condition = +cooling = 1 +disable_fan_first_layers = 3 +end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" +extrusion_multiplier = 0.9 +fan_always_on = 1 +fan_below_layer_time = 60 +filament_colour = #FFFFFF +filament_cost = 27.4375 +filament_density = 1.27 +filament_diameter = 2.85 +filament_max_volumetric_speed = 0 +filament_notes = "" +filament_settings_id = +filament_soluble = 0 +filament_type = PLA +first_layer_bed_temperature = 75 +first_layer_temperature = 250 +max_fan_speed = 100 +min_fan_speed = 100 +min_print_speed = 5 +slowdown_below_layer_time = 20 +start_filament_gcode = "; Filament gcode\n" +temperature = 220 + +[filament:PLA 175] +bed_temperature = 0 +bridge_fan_speed = 100 +compatible_printers = +compatible_printers_condition = +cooling = 1 +disable_fan_first_layers = 3 +end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" +extrusion_multiplier = 1 +fan_always_on = 1 +fan_below_layer_time = 60 +filament_colour = #FFFFFF +filament_cost = 0 +filament_density = 0 +filament_diameter = 1.75 +filament_max_volumetric_speed = 0 +filament_notes = "" +filament_settings_id = +filament_soluble = 0 +filament_type = PLA +first_layer_bed_temperature = 0 +first_layer_temperature = 230 +max_fan_speed = 60 +min_fan_speed = 35 +min_print_speed = 5 +slowdown_below_layer_time = 10 +start_filament_gcode = "; Filament gcode\n" +temperature = 200 + +[filament:PLA 285] +bed_temperature = 60 +bridge_fan_speed = 100 +compatible_printers = +compatible_printers_condition = +cooling = 1 +disable_fan_first_layers = 10 +end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" +extrusion_multiplier = 1 +fan_always_on = 1 +fan_below_layer_time = 60 +filament_colour = #FFFFFF +filament_cost = 0 +filament_density = 0 +filament_diameter = 2.85 +filament_max_volumetric_speed = 0 +filament_notes = "" +filament_settings_id = +filament_soluble = 0 +filament_type = PLA +first_layer_bed_temperature = 75 +first_layer_temperature = 230 +max_fan_speed = 100 +min_fan_speed = 100 +min_print_speed = 5 +slowdown_below_layer_time = 20 +start_filament_gcode = "; Filament gcode\n" +temperature = 220 + +[filament:WillowFlex 285] +bed_temperature = 60 +bridge_fan_speed = 100 +compatible_printers = +compatible_printers_condition = +cooling = 1 +disable_fan_first_layers = 0 +end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" +extrusion_multiplier = 0.9 +fan_always_on = 1 +fan_below_layer_time = 60 +filament_colour = #FFFFFF +filament_cost = 27.4375 +filament_density = 1.27 +filament_diameter = 2.85 +filament_max_volumetric_speed = 0 +filament_notes = "" +filament_settings_id = +filament_soluble = 0 +filament_type = PLA +first_layer_bed_temperature = 60 +first_layer_temperature = 175 +max_fan_speed = 100 +min_fan_speed = 100 +min_print_speed = 5 +slowdown_below_layer_time = 20 +start_filament_gcode = "; Filament gcode\n" +temperature = 175 + +[printer:Kossel] +bed_shape = 79.5618x8.36228,78.2518x16.6329,76.0845x24.7214,73.0836x32.5389,69.282x40,64.7214x47.0228,59.4516x53.5304,53.5304x59.4516,47.0228x64.7214,40x69.282,32.5389x73.0836,24.7214x76.0845,16.6329x78.2518,8.36228x79.5618,0x80,-8.36228x79.5618,-16.6329x78.2518,-24.7214x76.0845,-32.5389x73.0836,-40x69.282,-47.0228x64.7214,-53.5304x59.4516,-59.4516x53.5304,-64.7214x47.0228,-69.282x40,-73.0836x32.5389,-76.0845x24.7214,-78.2518x16.6329,-79.5618x8.36228,-80x0,-79.5618x-8.36228,-78.2518x-16.6329,-76.0845x-24.7214,-73.0836x-32.5389,-69.282x-40,-64.7214x-47.0228,-59.4516x-53.5304,-53.5304x-59.4516,-47.0228x-64.7214,-40x-69.282,-32.5389x-73.0836,-24.7214x-76.0845,-16.6329x-78.2518,-8.36228x-79.5618,0x-80,8.36228x-79.5618,16.6329x-78.2518,24.7214x-76.0845,32.5389x-73.0836,40x-69.282,47.0228x-64.7214,53.5304x-59.4516,59.4516x-53.5304,64.7214x-47.0228,69.282x-40,73.0836x-32.5389,76.0845x-24.7214,78.2518x-16.6329,79.5618x-8.36228,80x0 before_layer_gcode = -end_gcode = M104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200 ;\nG28 X0 ; home X axis\nM84 ; disable motors\n\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\n -extruder_offset = 0x0 +between_objects_gcode = +deretract_speed = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0 +end_gcode = M104 S0 ; turn off nozzle temperature\nG28; Home\nM84 ; disable motors\nM82; absolute E +extruder_colour = #FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000 +extruder_offset = 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 gcode_flavor = reprap layer_gcode = -nozzle_diameter = 0.35 +max_layer_height = 0.3,0.3,0.3,0.3,0.3,0.3,0.3,0.3,0.3,0.3,0.3,0.3,0.3,0.3,0.3,0.3 +min_layer_height = 0.07,0.07,0.07,0.07,0.07,0.07,0.07,0.07,0.07,0.07,0.07,0.07,0.07,0.07,0.07,0.07 +nozzle_diameter = 0.4,0.4,0.4,0.4,0.4,0.4,0.4,0.4,0.4,0.4,0.4,0.4,0.4,0.4,0.4,0.4 octoprint_apikey = octoprint_host = -pressure_advance = 0 -retract_before_travel = 2 -retract_layer_change = 1 -retract_length = 3 -retract_length_toolchange = 3 -retract_lift = 0 -retract_restart_extra = 0 -retract_restart_extra_toolchange = 0 -retract_speed = 40 -start_gcode = G28 ; home all axes\n +printer_notes = +printer_settings_id = +retract_before_travel = 2,2,2,2,2,2,2,2,2,2,2,2,2,2,2,2 +retract_before_wipe = 0%,0%,0%,0%,0%,0%,0%,0%,0%,0%,0%,0%,0%,0%,0%,0% +retract_layer_change = 1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1 +retract_length = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0 +retract_length_toolchange = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0 +retract_lift = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0 +retract_lift_above = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0 +retract_lift_below = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0 +retract_restart_extra = 0.01,0.01,0.01,0.01,0.01,0.01,0.01,0.01,0.01,0.01,0.01,0.01,0.01,0.01,0.01,0.01 +retract_restart_extra_toolchange = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0 +retract_speed = 20,20,20,20,20,20,20,20,20,20,20,20,20,20,20,20 +serial_port = +serial_speed = 250000 +single_extruder_multi_material = 1 +start_gcode = ;M104 S230 ;Temperatur\n;G29 S2 ;Autobed Level\n;G132 S1 ;Store Offset\n\nM83 ;relativ E \n\n; Cyan\nM163 S0 P1\nM163 S1 P0\nM163 S2 P0\nM164 S0\n\n; Ocean\nM163 S0 P5\nM163 S1 P1\nM163 S2 P0\nM164 S1\n\n; Blue\nM163 S0 P1\nM163 S1 P1\nM163 S2 P0\nM164 S2\n\n; Violet\nM163 S0 P1\nM163 S1 P5\nM163 S2 P0\nM164 S3\n\n; Magenta\nM163 S0 P0\nM163 S1 P1\nM163 S2 P0\nM164 S4\n\n; Raspberry\nM163 S0 P0\nM163 S1 P5\nM163 S2 P1\nM164 S5\n\n; Red\nM163 S0 P0\nM163 S1 P5\nM163 S2 P1\nM164 S6\n\n; Orange\nM163 S0 P0\nM163 S1 P1\nM163 S2 P1\nM164 S7\n\n; Yellow\nM163 S0 P0\nM163 S1 P0\nM163 S2 P1\nM164 S8\n\n; Spring Green\nM163 S0 P1\nM163 S1 P0\nM163 S2 P5\nM164 S9\n\n; Green\nM163 S0 P1\nM163 S1 P0\nM163 S2 P1\nM164 S10\n\n; Turquoise\nM163 S0 P5\nM163 S1 P0\nM163 S2 P1\nM164 S11\n\n\n; Cyan-Brown\nM163 S0 P2\nM163 S1 P1\nM163 S2 P1\nM164 S12\n\n; Magenta-Brown\nM163 S0 P1\nM163 S1 P2\nM163 S2 P1\nM164 S13\n\n; Yellow-Brown\nM163 S0 P1\nM163 S1 P1\nM163 S2 P2\nM164 S14\n\n; Brown\nM163 S0 P1\nM163 S1 P1\nM163 S2 P1\nM164 S15\n toolchange_gcode = use_firmware_retraction = 0 -use_relative_e_distances = 0 +use_relative_e_distances = 1 use_volumetric_e = 0 -vibration_limit = 0 -wipe = 0 +variable_layer_height = 0 +wipe = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0 z_offset = 0 -[printer:MendelPro] -bed_shape = 0x0,220x0,220x177,0x177 +[printer:Lulzbot] +bed_shape = 0x0,300x0,300x300,0x300 before_layer_gcode = -end_gcode = M104 S0 ; turn off temperature\nM140 S0;\nG28 X0 ; home X axis\nG0 Y177;\nM84 ; disable motors\n +between_objects_gcode = +deretract_speed = 0 +end_gcode = M104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200 ;\nG28 X0 ; home X axis\nM84 ; disable motors\n\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\n +extruder_colour = "" extruder_offset = 0x0 gcode_flavor = reprap layer_gcode = -nozzle_diameter = 0.5 -octoprint_apikey = 176444E92BFF48819CE0D8F1B264A91C +max_layer_height = 0.3 +min_layer_height = 0.07 +nozzle_diameter = 0.35 +octoprint_apikey = octoprint_host = -pressure_advance = 0 +printer_notes = +printer_settings_id = retract_before_travel = 2 +retract_before_wipe = 0% retract_layer_change = 1 retract_length = 5 -retract_length_toolchange = 10 +retract_length_toolchange = 3 retract_lift = 0 +retract_lift_above = 1 +retract_lift_below = 0 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 -retract_speed = 40 -start_gcode = G28 Z ; home Z\nG28 X Y ; home X Y\n +retract_speed = 60 +serial_port = +serial_speed = 250000 +single_extruder_multi_material = 0 +start_gcode = G28 ; home all axes\n toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 0 use_volumetric_e = 0 -vibration_limit = 0 -wipe = 0 +variable_layer_height = 0 +wipe = 1 z_offset = 0 -[printer:TinyBoy] -bed_shape = 0x0,88x0,88x74,0x74 +[printer:Mendel] +bed_shape = 0x0,218x0,218x201,0x201 before_layer_gcode = -end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n +between_objects_gcode = +deretract_speed = 0 +end_gcode = M104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200 ;\nG28 X0 ; home X axis\nM84 ; disable motors\n\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\n +extruder_colour = "" extruder_offset = 0x0 gcode_flavor = reprap layer_gcode = -nozzle_diameter = 0.4 -octoprint_apikey = 176444E92BFF48819CE0D8F1B264A91C +max_layer_height = 0.3 +min_layer_height = 0.07 +nozzle_diameter = 0.5 +octoprint_apikey = octoprint_host = -pressure_advance = 0 +printer_notes = +printer_settings_id = retract_before_travel = 2 +retract_before_wipe = 0% retract_layer_change = 1 -retract_length = 5 -retract_length_toolchange = 10 +retract_length = 2 +retract_length_toolchange = 3 retract_lift = 0 -retract_restart_extra = 0 +retract_lift_above = 0 +retract_lift_below = 0 +retract_restart_extra = 0.01 retract_restart_extra_toolchange = 0 -retract_speed = 40 -start_gcode = G28 Z ; home Z\nG0 Z 1 ; lift Z\nG28 X Y ; home X Y\n +retract_speed = 20 +serial_port = +serial_speed = 250000 +single_extruder_multi_material = 0 +start_gcode = G28 ; home all axes\n toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 0 use_volumetric_e = 0 -vibration_limit = 0 +variable_layer_height = 1 wipe = 0 z_offset = 0 -[printer:Toyrep] -bed_shape = 0x0,125x0,125x125,0x125 +[printer:Tiny] +bed_shape = 0x0,80x0,80x74,0x74 before_layer_gcode = -end_gcode = M104 S0 ; turn off nozzle temperature\nM84 ; disable motors +between_objects_gcode = +deretract_speed = 0 +end_gcode = M104 S0 ; turn off nozzle temperature\nG28 X0 ; home X axis +extruder_colour = "" extruder_offset = 0x0 gcode_flavor = reprap layer_gcode = +max_layer_height = 0.3 +min_layer_height = 0.07 nozzle_diameter = 0.4 octoprint_apikey = octoprint_host = -pressure_advance = 0 +printer_notes = +printer_settings_id = retract_before_travel = 2 +retract_before_wipe = 0% retract_layer_change = 1 -retract_length = 0 +retract_length = 2 retract_length_toolchange = 3 retract_lift = 0 -retract_restart_extra = 0 +retract_lift_above = 1 +retract_lift_below = 0 +retract_restart_extra = 0.01 retract_restart_extra_toolchange = 0 -retract_speed = 10 -start_gcode = \n +retract_speed = 40 +serial_port = +serial_speed = 250000 +single_extruder_multi_material = 0 +start_gcode = G28 ; home all axes\n toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 0 use_volumetric_e = 0 -vibration_limit = 0 +variable_layer_height = 1 wipe = 0 z_offset = 0 [printer:prusa i3] -bed_shape = 0x0,190x0,190x220,0x220 +bed_shape = 0x0,190x0,190x160,0x160 before_layer_gcode = +between_objects_gcode = +deretract_speed = 0 end_gcode = M104 S0 ; turn off temperature\nM140 S0 ; turn off bed temp \nG28 X0 ; home X axis\nG0 Y190 ; präsent object\nM84 ; disable motors\nM81 ; Power off\n\n +extruder_colour = "" extruder_offset = 0x0 gcode_flavor = reprap layer_gcode = +max_layer_height = 0 +min_layer_height = 0.07 nozzle_diameter = 0.4 octoprint_apikey = 176444E92BFF48819CE0D8F1B264A91C octoprint_host = -pressure_advance = 0 +printer_notes = retract_before_travel = 2 -retract_layer_change = 0 -retract_length = 3 +retract_before_wipe = 0% +retract_layer_change = 1 +retract_length = 4 retract_length_toolchange = 10 retract_lift = 0 +retract_lift_above = 0 +retract_lift_below = 0 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 40 -start_gcode = G28 Z ; home Z\n;G0 Z1 ; lift Z\nG28 X Y ; home X Y\nG0 Y40 ; clab move -toolchange_gcode = M83 ; turn on relative movement for extruder \nG1 E-5 ; retract filament 5mm \nG1 X10 Y10 Z4.000000 ; home X and Y axis leave Z at current height \nM84 E ; release extruder stepper motor from 'holding' position \n@pause ; pause print! \nG1 E0 ; reset extruder, ready to push out plastic again \nM82 ; set extruder movement back to absolute ready for next layer -use_firmware_retraction = 1 +serial_port = +serial_speed = 250000 +single_extruder_multi_material = 0 +start_gcode = G28 Z ; home Z\n;G0 Z1 ; lift Z\nG28 X Y ; home X Y\nG0 Y40 ; clab move +toolchange_gcode = M83 ; turn on relative movement for extruder \nG1 E-5 ; retract filament 5mm \nG1 X10 Y10 Z4.000000 ; home X and Y axis leave Z at current height \nM84 E ; release extruder stepper motor from 'holding' position \n@pause ; pause print! \nG1 E0 ; reset extruder, ready to push out plastic again \nM82 ; set extruder movement back to absolute ready for next layer +use_firmware_retraction = 0 use_relative_e_distances = 0 use_volumetric_e = 0 -vibration_limit = 0 +variable_layer_height = 1 wipe = 0 z_offset = 0 -[settings] -autocenter = 1 -mode = expert +[presets] +print = Tiny print +printer = Tiny +filament = PETG 175