From 916090ac88c00d2c7fa64a3f973ac3d9872f46f3 Mon Sep 17 00:00:00 2001 From: NoikK Date: Fri, 13 May 2016 15:05:28 +0000 Subject: [PATCH] Neue ini --- 3D-Drucker%2FSlicerBundle.ini.mw | 356 ++++++++++++++++++++++++------- 1 file changed, 283 insertions(+), 73 deletions(-) diff --git a/3D-Drucker%2FSlicerBundle.ini.mw b/3D-Drucker%2FSlicerBundle.ini.mw index ba07e006d..8d2478952 100644 --- a/3D-Drucker%2FSlicerBundle.ini.mw +++ b/3D-Drucker%2FSlicerBundle.ini.mw @@ -1,8 +1,8 @@ -# generated by Slic3r 1.2.9 on Mon May 9 21:40:16 2016 +# generated by Slic3r 1.2.9 on Fri May 13 17:04:53 2016 -[filament:LULZBOT PLA] -bed_temperature = 50 -bridge_fan_speed = 100 +[filament:LULZBOT ABS fine] +bed_temperature = 100 +bridge_fan_speed = 0 cooling = 1 disable_fan_first_layers = 1 extrusion_multiplier = 1 @@ -10,13 +10,13 @@ fan_always_on = 0 fan_below_layer_time = 60 filament_colour = #FFFFFF filament_diameter = 2.89 -first_layer_bed_temperature = 55 -first_layer_temperature = 190 -max_fan_speed = 100 -min_fan_speed = 35 -min_print_speed = 25 -slowdown_below_layer_time = 25 -temperature = 185 +first_layer_bed_temperature = 100 +first_layer_temperature = 250 +max_fan_speed = 0 +min_fan_speed = 0 +min_print_speed = 15 +slowdown_below_layer_time = 20 +temperature = 240 [filament:MendelPro ABS] bed_temperature = 0 @@ -36,6 +36,24 @@ min_print_speed = 5 slowdown_below_layer_time = 30 temperature = 245 +[filament:MendelPro Holz] +bed_temperature = 50 +bridge_fan_speed = 100 +cooling = 1 +disable_fan_first_layers = 1 +extrusion_multiplier = 1 +fan_always_on = 1 +fan_below_layer_time = 60 +filament_colour = #FFFFFF +filament_diameter = 1.7 +first_layer_bed_temperature = 55 +first_layer_temperature = 200 +max_fan_speed = 100 +min_fan_speed = 50 +min_print_speed = 5 +slowdown_below_layer_time = 30 +temperature = 185 + [filament:MendelPro PLA] bed_temperature = 50 bridge_fan_speed = 100 @@ -72,36 +90,54 @@ min_print_speed = 5 slowdown_below_layer_time = 15 temperature = 185 -[filament:prusa i3 ABS black] -bed_temperature = 0 +[filament:prusa i3 PLA black fine] +bed_temperature = 50 bridge_fan_speed = 100 -cooling = 0 -disable_fan_first_layers = 2 +cooling = 1 +disable_fan_first_layers = 1 extrusion_multiplier = 1 +fan_always_on = 1 +fan_below_layer_time = 60 +filament_colour = #FF0000 +filament_diameter = 2.9 +first_layer_bed_temperature = 50 +first_layer_temperature = 200 +max_fan_speed = 100 +min_fan_speed = 100 +min_print_speed = 5 +slowdown_below_layer_time = 15 +temperature = 200 + +[filament:prusa i3 PLA igus] +bed_temperature = 50 +bridge_fan_speed = 100 +cooling = 0 +disable_fan_first_layers = 1 +extrusion_multiplier = 0.9 fan_always_on = 0 fan_below_layer_time = 60 -filament_colour = #FFFFFF -filament_diameter = 2.8 -first_layer_bed_temperature = 0 +filament_colour = #D0C9B0 +filament_diameter = 2.9 +first_layer_bed_temperature = 50 first_layer_temperature = 250 max_fan_speed = 100 min_fan_speed = 35 min_print_speed = 5 slowdown_below_layer_time = 15 -temperature = 245 +temperature = 250 -[filament:prusa i3 PLA klar orange] +[filament:prusa i3 PLA rot] bed_temperature = 50 bridge_fan_speed = 100 cooling = 1 -disable_fan_first_layers = 2 +disable_fan_first_layers = 1 extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 60 -filament_colour = #FFFFFF -filament_diameter = 2.6 +filament_colour = #FF0000 +filament_diameter = 2.9 first_layer_bed_temperature = 50 -first_layer_temperature = 190 +first_layer_temperature = 200 max_fan_speed = 100 min_fan_speed = 35 min_print_speed = 5 @@ -109,47 +145,47 @@ slowdown_below_layer_time = 15 temperature = 200 [presets] -filament = TinyBoy PLA.ini -print = TinyBoy.ini -printer = prusa i3.ini +filament = LULZBOT ABS fine.ini +print = prusa i3 100.ini +printer = LULZBOT ABS fine.ini -[print:LULZBOT] -avoid_crossing_perimeters = 0 -bottom_solid_layers = 3 -bridge_acceleration = 2000 -bridge_flow_ratio = 1 -bridge_speed = 72 +[print:LULZBOT ABS fine ] +avoid_crossing_perimeters = 1 +bottom_solid_layers = 2 +bridge_acceleration = 1000 +bridge_flow_ratio = 1.1 +bridge_speed = 40 brim_width = 0 complete_objects = 0 -default_acceleration = 2000 +default_acceleration = 900 dont_support_bridges = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 -external_perimeter_speed = 45 +external_perimeter_speed = 30 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 -extrusion_width = 0.42 -fill_angle = 45 -fill_density = 20% -fill_pattern = rectilinear -first_layer_acceleration = 2000 -first_layer_extrusion_width = 0.53 -first_layer_height = 0.2 -first_layer_speed = 75% -gap_fill_speed = 55 +extrusion_width = 0.37 +fill_angle = 35 +fill_density = 30% +fill_pattern = line +first_layer_acceleration = 0 +first_layer_extrusion_width = 0.37 +first_layer_height = 120% +first_layer_speed = 85% +gap_fill_speed = 45 gcode_comments = 0 -infill_acceleration = 2000 -infill_every_layers = 1 +infill_acceleration = 1400 +infill_every_layers = 2 infill_extruder = 1 -infill_extrusion_width = 0.68 +infill_extrusion_width = 0.6 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 15% -infill_speed = 80 +infill_speed = 70 interface_shells = 0 -layer_height = 0.2 +layer_height = 0.14 max_print_speed = 80 max_volumetric_speed = 0 min_skirt_length = 0 @@ -158,24 +194,24 @@ only_retract_when_crossing_perimeters = 0 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 -perimeter_acceleration = 1200 +perimeter_acceleration = 900 perimeter_extruder = 1 -perimeter_extrusion_width = 0.38 -perimeter_speed = 75 -perimeters = 2 +perimeter_extrusion_width = 0.34 +perimeter_speed = 40 +perimeters = 4 post_process = raft_layers = 0 -resolution = 0.001 +resolution = 0 seam_position = aligned skirt_distance = 6 skirt_height = 1 -skirts = 3 -small_perimeter_speed = 50 -solid_infill_below_area = 90 +skirts = 2 +small_perimeter_speed = 30 +solid_infill_below_area = 30 solid_infill_every_layers = 0 solid_infill_extruder = 1 -solid_infill_extrusion_width = 0.5 -solid_infill_speed = 75 +solid_infill_extrusion_width = 0 +solid_infill_speed = 60 spiral_vase = 0 standby_temperature_delta = -5 support_material = 0 @@ -194,10 +230,10 @@ support_material_speed = 60 support_material_threshold = 45 thin_walls = 1 threads = 2 -top_infill_extrusion_width = 0.4 -top_solid_infill_speed = 60 -top_solid_layers = 3 -travel_speed = 160 +top_infill_extrusion_width = 0.35 +top_solid_infill_speed = 80% +top_solid_layers = 4 +travel_speed = 80 xy_size_compensation = 0 [print:MendelPro] @@ -219,7 +255,7 @@ extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0 fill_angle = 45 -fill_density = 20% +fill_density = 15% fill_pattern = rectilinear first_layer_acceleration = 0 first_layer_extrusion_width = 150% @@ -374,6 +410,180 @@ top_solid_layers = 3 travel_speed = 100 xy_size_compensation = 0 +[print:prusa i3 100] +avoid_crossing_perimeters = 0 +bottom_solid_layers = 3 +bridge_acceleration = 0 +bridge_flow_ratio = 1 +bridge_speed = 40 +brim_width = 0 +complete_objects = 0 +default_acceleration = 0 +dont_support_bridges = 1 +external_fill_pattern = rectilinear +external_perimeter_extrusion_width = 0 +external_perimeter_speed = 10 +external_perimeters_first = 0 +extra_perimeters = 1 +extruder_clearance_height = 20 +extruder_clearance_radius = 20 +extrusion_width = 0 +fill_angle = 45 +fill_density = 20% +fill_pattern = rectilinear +first_layer_acceleration = 0 +first_layer_extrusion_width = 0 +first_layer_height = 0.2 +first_layer_speed = 10 +gap_fill_speed = 10 +gcode_comments = 0 +infill_acceleration = 0 +infill_every_layers = 1 +infill_extruder = 1 +infill_extrusion_width = 110% +infill_first = 0 +infill_only_where_needed = 0 +infill_overlap = 15% +infill_speed = 0 +interface_shells = 0 +layer_height = 0.1 +max_print_speed = 80 +max_volumetric_speed = 0 +min_skirt_length = 1 +notes = +only_retract_when_crossing_perimeters = 1 +ooze_prevention = 0 +output_filename_format = [input_filename_base].gcode +overhangs = 1 +perimeter_acceleration = 0 +perimeter_extruder = 1 +perimeter_extrusion_width = 0 +perimeter_speed = 0 +perimeters = 3 +post_process = +raft_layers = 0 +resolution = 0 +seam_position = aligned +skirt_distance = 6 +skirt_height = 1 +skirts = 3 +small_perimeter_speed = 10 +solid_infill_below_area = 70 +solid_infill_every_layers = 0 +solid_infill_extruder = 1 +solid_infill_extrusion_width = 0 +solid_infill_speed = 0 +spiral_vase = 0 +standby_temperature_delta = -5 +support_material = 0 +support_material_angle = 0 +support_material_contact_distance = 0.2 +support_material_enforce_layers = 0 +support_material_extruder = 1 +support_material_extrusion_width = 0 +support_material_interface_extruder = 1 +support_material_interface_layers = 2 +support_material_interface_spacing = 0 +support_material_interface_speed = 100% +support_material_pattern = rectilinear +support_material_spacing = 5 +support_material_speed = 0 +support_material_threshold = 40 +thin_walls = 1 +threads = 2 +top_infill_extrusion_width = 0 +top_solid_infill_speed = 10 +top_solid_layers = 3 +travel_speed = 100 +xy_size_compensation = 0 + +[print:prusa i3 100 testtesttest] +avoid_crossing_perimeters = 0 +bottom_solid_layers = 0 +bridge_acceleration = 0 +bridge_flow_ratio = 1 +bridge_speed = 40 +brim_width = 0 +complete_objects = 0 +default_acceleration = 0 +dont_support_bridges = 1 +external_fill_pattern = rectilinear +external_perimeter_extrusion_width = 0 +external_perimeter_speed = 10 +external_perimeters_first = 0 +extra_perimeters = 1 +extruder_clearance_height = 20 +extruder_clearance_radius = 20 +extrusion_width = 0 +fill_angle = 45 +fill_density = 0% +fill_pattern = rectilinear +first_layer_acceleration = 0 +first_layer_extrusion_width = 0 +first_layer_height = 0.2 +first_layer_speed = 10 +gap_fill_speed = 10 +gcode_comments = 0 +infill_acceleration = 0 +infill_every_layers = 1 +infill_extruder = 1 +infill_extrusion_width = 110% +infill_first = 0 +infill_only_where_needed = 0 +infill_overlap = 15% +infill_speed = 0 +interface_shells = 0 +layer_height = 0.1 +max_print_speed = 80 +max_volumetric_speed = 0 +min_skirt_length = 1 +notes = +only_retract_when_crossing_perimeters = 1 +ooze_prevention = 0 +output_filename_format = [input_filename_base].gcode +overhangs = 1 +perimeter_acceleration = 0 +perimeter_extruder = 1 +perimeter_extrusion_width = 0 +perimeter_speed = 0 +perimeters = 1 +post_process = +raft_layers = 0 +resolution = 0 +seam_position = aligned +skirt_distance = 1 +skirt_height = 1 +skirts = 1 +small_perimeter_speed = 10 +solid_infill_below_area = 70 +solid_infill_every_layers = 0 +solid_infill_extruder = 1 +solid_infill_extrusion_width = 0 +solid_infill_speed = 0 +spiral_vase = 0 +standby_temperature_delta = -5 +support_material = 0 +support_material_angle = 0 +support_material_contact_distance = 0.2 +support_material_enforce_layers = 0 +support_material_extruder = 1 +support_material_extrusion_width = 0 +support_material_interface_extruder = 1 +support_material_interface_layers = 2 +support_material_interface_spacing = 0 +support_material_interface_speed = 100% +support_material_pattern = rectilinear +support_material_spacing = 5 +support_material_speed = 0 +support_material_threshold = 40 +thin_walls = 1 +threads = 2 +top_infill_extrusion_width = 0 +top_solid_infill_speed = 10 +top_solid_layers = 0 +travel_speed = 100 +xy_size_compensation = 0 + [print:prusa i3 250] avoid_crossing_perimeters = 0 bottom_solid_layers = 3 @@ -466,14 +676,14 @@ avoid_crossing_perimeters = 0 bottom_solid_layers = 3 bridge_acceleration = 0 bridge_flow_ratio = 1 -bridge_speed = 40 +bridge_speed = 60 brim_width = 0 complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 -external_perimeter_speed = 10 +external_perimeter_speed = 20 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 @@ -485,7 +695,7 @@ fill_pattern = rectilinear first_layer_acceleration = 0 first_layer_extrusion_width = 0 first_layer_height = 0.2 -first_layer_speed = 15 +first_layer_speed = 10 gap_fill_speed = 10 gcode_comments = 0 infill_acceleration = 0 @@ -635,25 +845,25 @@ top_solid_layers = 3 travel_speed = 100 xy_size_compensation = 0 -[printer:LULZBOT] -bed_shape = 0x0,300x0,300x300,0x300 +[printer:LULZBOT ABS fine] +bed_shape = 0x0,298x0,298x275,0x275 before_layer_gcode = -end_gcode = M400 ; \nM104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200\nG28 X0 ; home X axis\nM84 ; disable motors +end_gcode = M104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200 ;\nG28 X0 ; home X axis\nM84 ; disable motors extruder_offset = 0x0 gcode_flavor = reprap layer_gcode = -nozzle_diameter = 0.5 +nozzle_diameter = 0.35 octoprint_apikey = octoprint_host = pressure_advance = 0 retract_before_travel = 2 retract_layer_change = 1 -retract_length = 1.9 +retract_length = 1.75 retract_length_toolchange = 3 retract_lift = 0 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 -retract_speed = 30 +retract_speed = 20 start_gcode = G28 ; home all axes toolchange_gcode = use_firmware_retraction = 0 -- 2.20.1