projectconfig.h

   1 /**************************************************************************/
   2 /*!
   3     @file     projectconfig.h
   4     @author   K. Townsend (microBuilder.eu)
   5
   6     @section LICENSE
   7
   8     Software License Agreement (BSD License)
   9
  10     Copyright (c) 2010, microBuilder SARL
  11     All rights reserved.
  12
  13     Redistribution and use in source and binary forms, with or without
  14     modification, are permitted provided that the following conditions are met:
  15     1. Redistributions of source code must retain the above copyright
  16     notice, this list of conditions and the following disclaimer.
  17     2. Redistributions in binary form must reproduce the above copyright
  18     notice, this list of conditions and the following disclaimer in the
  19     documentation and/or other materials provided with the distribution.
  20     3. Neither the name of the copyright holders nor the
  21     names of its contributors may be used to endorse or promote products
  22     derived from this software without specific prior written permission.
  23
  24     THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS ''AS IS'' AND ANY
  25     EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
  26     WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
  27     DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER BE LIABLE FOR ANY
  28     DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
  29     (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
  30     LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
  31     ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
  32     (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
  33     SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  34 */
  35 /**************************************************************************/
  36
  37 #ifndef _PROJECTCONFIG_H_
  38 #define _PROJECTCONFIG_H_
  39
  40 #include "lpc134x.h"
  41 #include "sysdefs.h"
  42
  43 /*=========================================================================
  44     BOARD SELECTION
  45
  46     Because several boards use this code library with sometimes slightly
  47     different pin configuration, you will need to specify which board you
  48     are using by enabling one of the following definitions. The code base
  49     will then try to configure itself accordingly for that board.
  50
  51     CFG_BRD_LPC1343_REFDESIGN
  52     =========================
  53
  54         microBuilder.eu LPC1343 Reference Design base board with
  55         on-board peripherals initialised (EEPROM, USB or UART CLI, etc.)
  56
  57                 This is the recommended starting point for new development
  58                 since it makes it easy to send printf output to USB CDC, access
  59                 the on-board EEPROM, etc.
  60
  61     CFG_BRD_LPC1343_REFDESIGN_MINIMAL
  62     =================================
  63
  64         microBuilder.eu LPC1343 Reference Design base board with
  65         only the most common peripherals initialised by default.
  66
  67         Results in smallest code since EEPROM, USB, etc., are not
  68         initialised on startup.  By default, only the following
  69         peripherals are initialised by systemInit():
  70
  71               - CPU (Configures the PLL, etc.)
  72               - GPIO
  73               - SysTick Timer
  74               - UART (with printf support) *
  75
  76         * Can be removed to save 0.8kb in debug and 0.3 kb in
  77         release. Comment out 'CFG_PRINTF_UART' to disable it.
  78
  79         The code size can be further reduced by several KB by removing
  80         any IRQ Handlers that are not used.  The I2C IRQHandler, for
  81         example, uses ~1KB of flash in debug and ~400KB in release mode,
  82         but because it is referenced in the startup code it is always
  83         included even if I2C is never used in the project.
  84
  85         Other IRQ Handlers that you might be able to comment out
  86         to save some space are:
  87
  88         IRQ Handler               Debug   Release
  89         ------------------------- ------  -------
  90         I2C_IRQHandler            1160 b    400 b
  91         SSP_IRQHandler             160 b     76 b
  92         UART_IRQHandler            246 b    116 b
  93         WAKEUP_IRQHandler          160 b    100 b
  94         WDT_IRQHandler              50 b     28 b
  95
  96     CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
  97     ====================================
  98
  99         microBuilder.eu/Adafruit Stand-Alone "Smart LCD" with USB enabled
 100         for the CLI interface.
 101
 102     CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 103     =====================================
 104
 105         microBuilder.eu/Adafruit Stand-Alone "Smart LCD" with UART enabled
 106         for the CLI interface.
 107
 108     CFG_BRD_LPC1343_802154USBSTICK
 109     ==============================
 110
 111         microBuilder.eu USB stick 802.15.4 868/915MHz RF transceiver
 112
 113     -----------------------------------------------------------------------*/
 114     #define CFG_BRD_LPC1343_REFDESIGN
 115     // #define CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 116     // #define CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
 117     // #define CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 118     // #define CFG_BRD_LPC1343_802154USBSTICK
 119     // #define CFG_BRD_LPC1343_OLIMEX_P
 120 /*=========================================================================*/
 121
 122
 123 /**************************************************************************
 124     PIN USAGE
 125     -----------------------------------------------------------------------
 126     This table tries to give an indication of which GPIO pins and
 127     peripherals are used by the available drivers and SW examples.  Only
 128     dedicated GPIO pins available on the LPC1343 Reference Board are shown
 129     below.  Any unused peripheral blocks like I2C, SSP, ADC, etc., can
 130     also be used as GPIO if they are available.
 131
 132                 PORT 1        PORT 2                PORT 3
 133                 =========     =================     =======
 134                 8 9 10 11     1 2 3 4 5 6 7 8 9     0 1 2 3
 135
 136     SDCARD      . .  .  .     . . . . . . . . .     X . . .
 137     PWM         . X  .  .     . . . . . . . . .     . . . .
 138     STEPPER     . .  .  .     . . . . . . . . .     X X X X
 139     CHIBI       X X  X  .     . . . . . . . . .     . . . .
 140     ILI9325/8   X X  X  X     X X X X X X X X X     . . . X
 141     ST7565      X X  X  X     X X X X X X X X X     . . . X
 142     ST7735      . .  .  .     X X X X X X . . .     . . . .
 143     SHARPMEM    . .  .  .     X X X X . . . . .     . . . .
 144     SSD1306     . .  .  .     X X X . X X . . .     . . . .
 145     SSD1351     . .  .  .     X X X X X . . . .     . . . .
 146     MCP121      . .  .  .     . . . . . . . . .     . X . .
 147     PN532 [3]   . .  .  .     . . . . . . . . .     . X X .
 148
 149                 TIMERS                    SSP     ADC         UART
 150                 ======================    ===     =======     ====
 151                 16B0  16B1  32B0  32B1    0       0 1 2 3     0
 152
 153     SDCARD      .     .     .     .       X       . . . .     .
 154     PWM         .     X     .     .       .       . . . .     .
 155     PMU [1]     .     .     X     .       .       . . . .     .
 156     USB         .     .     .     X       .       . . . .     .
 157     STEPPER     .     .     X     .       .       . . . .     .
 158     CHIBI       x     .     .     .       X       . . . .     .
 159     ILI9325/8   .     .     .     .       .       X X X X     .
 160     ST7565      .     .     .     .       .       X X X X     .
 161     ST7535      .     .     .     .       .       . . . .     .
 162     SHARPMEM    .     .     .     .       .       . . . .     .
 163     SSD1306     .     .     .     .       .       . . . .     .
 164     INTERFACE   .     .     .     .       .       . . . .     X[2]
 165
 166     [1]  PMU uses 32-bit Timer 0 for SW wakeup from deep-sleep.  This timer
 167          can safely be used by other peripherals, but may need to be
 168          reconfigured when you wakeup from deep-sleep.
 169     [2]  INTERFACE can be configured to use either USBCDC or UART
 170     [3]  3.2 only used when with the I2C bus (for IRQ)
 171
 172  **************************************************************************/
 173
 174
 175 /**************************************************************************
 176     I2C Addresses
 177     -----------------------------------------------------------------------
 178     The following addresses are used by the different I2C sensors included
 179     in the code base [1]
 180
 181                                 HEX       BINARY
 182                                 ====      ========
 183     ISL12022M (RTC)             0xDE      1101111x
 184     ISL12022M (SRAM)            0xAE      1010111x
 185     LM75B                       0x90      1001000x
 186     MCP24AA                     0xA0      1010000x
 187     MCP4725                     0xC0      1100000x
 188     TSL2561                     0x72      0111001x
 189     TCS3414                     0x72      0111001x
 190
 191     [1]  Alternative addresses may exists, but the addresses listed in this
 192          table are the values used in the code base
 193
 194  **************************************************************************/
 195
 196
 197 /*=========================================================================
 198     FIRMWARE VERSION SETTINGS
 199     -----------------------------------------------------------------------*/
 200     #define CFG_FIRMWARE_VERSION_MAJOR            (0)
 201     #define CFG_FIRMWARE_VERSION_MINOR            (9)
 202     #define CFG_FIRMWARE_VERSION_REVISION         (8)
 203 /*=========================================================================*/
 204
 205
 206 /*=========================================================================
 207     CORE CPU SETTINGS
 208     -----------------------------------------------------------------------
 209
 210     CFG_CPU_CCLK    Value is for reference only.  'core/cpu/cpu.c' must
 211                     be modified to change the clock speed, but the value
 212                     should be indicated here since CFG_CPU_CCLK is used by
 213                     other peripherals to determine timing.
 214
 215     -----------------------------------------------------------------------*/
 216     #define CFG_CPU_CCLK                (72000000)  // 1 tick = 13.88nS
 217 /*=========================================================================*/
 218
 219
 220 /*=========================================================================
 221     SYSTICK TIMER
 222     -----------------------------------------------------------------------
 223
 224     CFG_SYSTICK_DELAY_IN_MS   The number of milliseconds between each tick
 225                               of the systick timer.
 226
 227     -----------------------------------------------------------------------*/
 228     #define CFG_SYSTICK_DELAY_IN_MS     (1)
 229 /*=========================================================================*/
 230
 231
 232 /*=========================================================================
 233     ALTERNATE RESET PIN
 234     -----------------------------------------------------------------------
 235
 236     CFG_ALTRESET        If defined, indicates that a GPIO pin should be
 237                         configured as an alternate reset pin in addition
 238                         to the dedicated reset pin.
 239     CFG_ALTRESET_PORT   The GPIO port where the alt reset pin is located
 240     CFG_ALTRESET_PIN    The GPIO pin where the alt reset pin is located
 241
 242     -----------------------------------------------------------------------*/
 243     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 244       #define CFG_ALTRESET
 245       #define CFG_ALTRESET_PORT         (1)
 246       #define CFG_ALTRESET_PIN          (5)   // P1.5 = RTS
 247     #endif
 248 /*=========================================================================*/
 249
 250
 251 /*=========================================================================
 252     UART
 253     -----------------------------------------------------------------------
 254
 255     CFG_UART_BAUDRATE         The default UART speed.  This value is used
 256                               when initialising UART, and should be a
 257                               standard value like 57600, 9600, etc.
 258                               NOTE: This value may be overridden if
 259                               another value is stored in EEPROM!
 260     CFG_UART_BUFSIZE          The length in bytes of the UART RX FIFO. This
 261                               will determine the maximum number of received
 262                               characters to store in memory.
 263
 264     -----------------------------------------------------------------------*/
 265     #ifdef CFG_BRD_LPC1343_REFDESIGN
 266       #define CFG_UART_BAUDRATE           (115200)
 267       #define CFG_UART_BUFSIZE            (512)
 268     #endif
 269
 270     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 271       #define CFG_UART_BAUDRATE           (115200)
 272       #define CFG_UART_BUFSIZE            (512)
 273     #endif
 274
 275     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
 276       #define CFG_UART_BAUDRATE           (115200)
 277       #define CFG_UART_BUFSIZE            (512)
 278     #endif
 279
 280     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 281       #define CFG_UART_BAUDRATE           (57600)
 282       #define CFG_UART_BUFSIZE            (512)
 283     #endif
 284
 285     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 286       #define CFG_UART_BAUDRATE           (115200)
 287       #define CFG_UART_BUFSIZE            (512)
 288     #endif
 289
 290     #ifdef CFG_BRD_LPC1343_OLIMEX_P
 291       #define CFG_UART_BAUDRATE           (115200)
 292       #define CFG_UART_BUFSIZE            (512)
 293     #endif
 294 /*=========================================================================*/
 295
 296
 297 /*=========================================================================
 298     SSP
 299     -----------------------------------------------------------------------
 300
 301     CFG_SSP0_SCKPIN_2_11      Indicates which pin should be used for SCK0
 302     CFG_SSP0_SCKPIN_0_6
 303
 304     -----------------------------------------------------------------------*/
 305     #ifdef CFG_BRD_LPC1343_REFDESIGN
 306       #define CFG_SSP0_SCKPIN_2_11
 307       // #define CFG_SSP0_SCKPIN_0_6
 308     #endif
 309
 310     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 311       #define CFG_SSP0_SCKPIN_2_11
 312       // #define CFG_SSP0_SCKPIN_0_6
 313     #endif
 314
 315     #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 316       #define CFG_SSP0_SCKPIN_2_11
 317       // #define CFG_SSP0_SCKPIN_0_6
 318     #endif
 319
 320     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 321       // #define CFG_SSP0_SCKPIN_2_11
 322       #define CFG_SSP0_SCKPIN_0_6
 323     #endif
 324
 325     #ifdef CFG_BRD_LPC1343_OLIMEX_P
 326       #define CFG_SSP0_SCKPIN_2_11
 327       // #define CFG_SSP0_SCKPIN_0_6
 328     #endif
 329 /*=========================================================================*/
 330
 331
 332 /*=========================================================================
 333     ON-BOARD LED
 334     -----------------------------------------------------------------------
 335
 336     CFG_LED_PORT              The port for the on board LED
 337     CFG_LED_PIN               The pin for the on board LED
 338     CFG_LED_ON                The pin state to turn the LED on (0 = low, 1 = high)
 339     CFG_LED_OFF               The pin state to turn the LED off (0 = low, 1 = high)
 340
 341     -----------------------------------------------------------------------*/
 342     #ifdef CFG_BRD_LPC1343_REFDESIGN
 343       #define CFG_LED_PORT                (2)
 344       #define CFG_LED_PIN                 (10)
 345       #define CFG_LED_ON                  (0)
 346       #define CFG_LED_OFF                 (1)
 347     #endif
 348
 349     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 350       #define CFG_LED_PORT                (2)
 351       #define CFG_LED_PIN                 (10)
 352       #define CFG_LED_ON                  (0)
 353       #define CFG_LED_OFF                 (1)
 354     #endif
 355
 356     #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 357       #define CFG_LED_PORT                (2)
 358       #define CFG_LED_PIN                 (10)
 359       #define CFG_LED_ON                  (0)
 360       #define CFG_LED_OFF                 (1)
 361     #endif
 362
 363     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 364       #define CFG_LED_PORT                (3)
 365       #define CFG_LED_PIN                 (2)
 366       #define CFG_LED_ON                  (0)
 367       #define CFG_LED_OFF                 (1)
 368     #endif
 369
 370     #ifdef CFG_BRD_LPC1343_OLIMEX_P
 371       #define CFG_LED_PORT                (3)
 372       #define CFG_LED_PIN                 (2)
 373       #define CFG_LED_ON                  (0)
 374       #define CFG_LED_OFF                 (1)
 375     #endif
 376 /*=========================================================================*/
 377
 378
 379 /*=========================================================================
 380     MICRO-SD CARD
 381     -----------------------------------------------------------------------
 382
 383     CFG_SDCARD                If this field is defined SD Card and FAT32
 384                               file system support will be included
 385     CFG_SDCARD_READONLY       If this is set to 1, all commands to
 386                               write to the SD card will be removed
 387                               saving some flash space.
 388     CFG_SDCARD_CDPORT         The card detect port number
 389     CFG_SDCARD_CDPIN          The card detect pin number
 390
 391     NOTE:                     All config settings for FAT32 are defined
 392                               in ffconf.h
 393
 394     BENCHMARK:                With SPI set to 6.0MHz, FATFS can read
 395                               ~300KB/s (w/512 byte read buffer)
 396
 397     PIN LAYOUT:               The pin layout that is used by this driver
 398                               can be seen in the following schematic:
 399                               /tools/schematics/Breakout_TFTLCD_ILI9325_v1.3
 400
 401     DEPENDENCIES:             SDCARD requires the use of SSP0.
 402     -----------------------------------------------------------------------*/
 403     #ifdef CFG_BRD_LPC1343_REFDESIGN
 404       // #define CFG_SDCARD
 405       #define CFG_SDCARD_READONLY         (1)   // Must be 0 or 1
 406       #define CFG_SDCARD_CDPORT           (3)
 407       #define CFG_SDCARD_CDPIN            (0)
 408     #endif
 409
 410     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 411       // #define CFG_SDCARD
 412       #define CFG_SDCARD_READONLY         (1)   // Must be 0 or 1
 413       #define CFG_SDCARD_CDPORT           (3)
 414       #define CFG_SDCARD_CDPIN            (0)
 415     #endif
 416
 417     #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 418       #define CFG_SDCARD
 419       #define CFG_SDCARD_READONLY         (1)   // Must be 0 or 1
 420       #define CFG_SDCARD_CDPORT           (3)
 421       #define CFG_SDCARD_CDPIN            (0)
 422     #endif
 423
 424     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 425       // #define CFG_SDCARD
 426       #define CFG_SDCARD_READONLY         (1)   // Must be 0 or 1
 427       #define CFG_SDCARD_CDPORT           (3)
 428       #define CFG_SDCARD_CDPIN            (0)
 429     #endif
 430
 431     #ifdef CFG_BRD_LPC1343_OLIMEX_P
 432       // #define CFG_SDCARD
 433       #define CFG_SDCARD_READONLY         (1) // Must be 0 or 1
 434       #define CFG_SDCARD_CDPORT           (3)
 435       #define CFG_SDCARD_CDPIN            (0)
 436     #endif
 437 /*=========================================================================*/
 438
 439
 440 /*=========================================================================
 441     USB
 442     -----------------------------------------------------------------------
 443
 444     CFG_USBHID                If this field is defined USB HID support will
 445                               be included.  Currently uses ROM-based USB HID
 446     CFG_USBCDC                If this field is defined USB CDC support will
 447                               be included, with the USB Serial Port speed
 448                               set to 115200 BPS by default
 449     CFG_USBCDC_BAUDRATE       The default TX/RX speed.  This value is used
 450                               when initialising USBCDC, and should be a
 451                               standard value like 57600, 9600, etc.
 452     CFG_USBCDC_INITTIMEOUT    The maximum delay in milliseconds to wait for
 453                               USB to connect.  Must be a multiple of 10!
 454     CFG_USBCDC_BUFFERSIZE     Size of the buffer (in bytes) that stores
 455                               printf data until it can be sent out in
 456                               64 byte frames.  The buffer is required since
 457                               only one frame per ms can be sent using USB
 458                               CDC (see 'puts' in systeminit.c).
 459
 460     -----------------------------------------------------------------------*/
 461     #define CFG_USB_VID                   (0x239A)
 462     #define CFG_USB_PID                   (0x1002)
 463
 464     #ifdef CFG_BRD_LPC1343_REFDESIGN
 465       // #define CFG_USBHID
 466       #define CFG_USBCDC
 467       #define CFG_USBCDC_BAUDRATE         (115200)
 468       #define CFG_USBCDC_INITTIMEOUT      (5000)
 469       #define CFG_USBCDC_BUFFERSIZE       (256)
 470     #endif
 471
 472     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 473       // #define CFG_USBHID
 474       // #define CFG_USBCDC
 475       #define CFG_USBCDC_BAUDRATE         (115200)
 476       #define CFG_USBCDC_INITTIMEOUT      (5000)
 477       #define CFG_USBCDC_BUFFERSIZE       (256)
 478     #endif
 479
 480     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
 481       // #define CFG_USBHID
 482       #define CFG_USBCDC
 483       #define CFG_USBCDC_BAUDRATE         (115200)
 484       #define CFG_USBCDC_INITTIMEOUT      (5000)
 485       #define CFG_USBCDC_BUFFERSIZE       (256)
 486     #endif
 487
 488     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 489       // #define CFG_USBHID
 490       // #define CFG_USBCDC
 491       #define CFG_USBCDC_BAUDRATE         (57600)
 492       #define CFG_USBCDC_INITTIMEOUT      (5000)
 493       #define CFG_USBCDC_BUFFERSIZE       (256)
 494     #endif
 495
 496     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 497       // #define CFG_USBHID
 498       #define CFG_USBCDC
 499       #define CFG_USBCDC_BAUDRATE         (115200)
 500       #define CFG_USBCDC_INITTIMEOUT      (5000)
 501       #define CFG_USBCDC_BUFFERSIZE       (256)
 502     #endif
 503
 504     #ifdef CFG_BRD_LPC1343_OLIMEX_P
 505       // #define CFG_USBHID
 506       #define CFG_USBCDC
 507       #define CFG_USBCDC_BAUDRATE         (115200)
 508       #define CFG_USBCDC_INITTIMEOUT      (5000)
 509       #define CFG_USBCDC_BUFFERSIZE       (256)
 510     #endif
 511 /*=========================================================================*/
 512
 513
 514 /*=========================================================================
 515     PRINTF REDIRECTION
 516     -----------------------------------------------------------------------
 517
 518     CFG_PRINTF_UART           Will cause all printf statements to be
 519                               redirected to UART
 520     CFG_PRINTF_USBCDC         Will cause all printf statements to be
 521                               redirect to USB Serial
 522     CFG_PRINTF_NEWLINE        This is typically "\r\n" for Windows or
 523                               "\n" for *nix
 524
 525     Note: If no printf redirection definitions are present, all printf
 526     output will be ignored.
 527     -----------------------------------------------------------------------*/
 528     #ifdef CFG_BRD_LPC1343_REFDESIGN
 529       // #define CFG_PRINTF_UART
 530       #define CFG_PRINTF_USBCDC
 531       #define CFG_PRINTF_NEWLINE          "\r\n"
 532     #endif
 533
 534     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 535       #define CFG_PRINTF_UART
 536       // #define CFG_PRINTF_USBCDC
 537       #define CFG_PRINTF_NEWLINE          "\r\n"
 538     #endif
 539
 540     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
 541       // #define CFG_PRINTF_UART
 542       #define CFG_PRINTF_USBCDC
 543       #define CFG_PRINTF_NEWLINE          "\r\n"
 544     #endif
 545
 546     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 547       #define CFG_PRINTF_UART
 548       // #define CFG_PRINTF_USBCDC
 549       #define CFG_PRINTF_NEWLINE          "\n"
 550     #endif
 551
 552     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 553       // #define CFG_PRINTF_UART
 554       #define CFG_PRINTF_USBCDC
 555       #define CFG_PRINTF_NEWLINE          "\r\n"
 556     #endif
 557
 558     #ifdef CFG_BRD_LPC1343_OLIMEX_P
 559       // #define CFG_PRINTF_UART
 560       #define CFG_PRINTF_USBCDC
 561       #define CFG_PRINTF_NEWLINE          "\r\n"
 562     #endif
 563 /*=========================================================================*/
 564
 565
 566 /*=========================================================================
 567     COMMAND LINE INTERFACE
 568     -----------------------------------------------------------------------
 569
 570     CFG_INTERFACE             If this field is defined the UART or USBCDC
 571                               based command-line interface will be included
 572     CFG_INTERFACE_MAXMSGSIZE  The maximum number of bytes to accept for an
 573                               incoming command
 574     CFG_INTERFACE_PROMPT      The command prompt to display at the start
 575                               of every new data entry line
 576     CFG_INTERFACE_SILENTMODE  If this is set to 1 only text generated in
 577                               response to commands will be send to the
 578                               output buffer.  The command prompt will not
 579                               be displayed and incoming text will not be
 580                               echoed back to the output buffer (allowing
 581                               you to see the text you have input).  This
 582                               is normally only desirable in a situation
 583                               where another MCU is communicating with
 584                               the LPC1343.
 585     CFG_INTERFACE_DROPCR      If this is set to 1 all incoming \r
 586                               characters will be dropped
 587     CFG_INTERFACE_ENABLEIRQ   If this is set to 1 the IRQ pin will be
 588                               set high when a command starts executing
 589                               and will go low when the command has
 590                               finished executing or the LCD is not busy.
 591                               This allows another device to know when a
 592                               new command can safely be sent.
 593     CFG_INTERFACE_IRQPORT     The gpio port for the IRQ/busy pin
 594     CFG_INTERFACE_IRQPIN      The gpio pin number for the IRQ/busy pin
 595     CFG_INTERFACE_SHORTERRORS If this is enabled only short 1 character
 596                               error messages will be returned (followed
 597                               by CFG_PRINTF_NEWLINE), rather than more
 598                               verbose error messages.  The specific
 599                               characters used are defined below.
 600     CFG_INTERFACE_CONFIRMREADY  If this is set to 1 a text confirmation
 601                               will be sent when the command prompt is
 602                               ready for a new command.  This is in
 603                               addition to CFG_INTERFACE_ENABLEIRQ if
 604                               this is also enabled.  The character used
 605                               is defined below.
 606
 607     NOTE:                     The command-line interface will use either
 608                               USB-CDC or UART depending on whether
 609                               CFG_PRINTF_UART or CFG_PRINTF_USBCDC are
 610                               selected.
 611     -----------------------------------------------------------------------*/
 612     #ifdef CFG_BRD_LPC1343_REFDESIGN
 613       #define CFG_INTERFACE
 614       #define CFG_INTERFACE_MAXMSGSIZE    (256)
 615       #define CFG_INTERFACE_PROMPT        "LPC1343 >> "
 616       #define CFG_INTERFACE_SILENTMODE    (0)
 617       #define CFG_INTERFACE_DROPCR        (0)
 618       #define CFG_INTERFACE_ENABLEIRQ     (0)
 619       #define CFG_INTERFACE_IRQPORT       (0)
 620       #define CFG_INTERFACE_IRQPIN        (7)
 621       #define CFG_INTERFACE_SHORTERRORS   (0)
 622       #define CFG_INTERFACE_CONFIRMREADY  (0)
 623     #endif
 624
 625     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 626       // #define CFG_INTERFACE
 627       #define CFG_INTERFACE_MAXMSGSIZE    (256)
 628       #define CFG_INTERFACE_PROMPT        "LPC1343 >> "
 629       #define CFG_INTERFACE_SILENTMODE    (0)
 630       #define CFG_INTERFACE_DROPCR        (0)
 631       #define CFG_INTERFACE_ENABLEIRQ     (0)
 632       #define CFG_INTERFACE_IRQPORT       (0)
 633       #define CFG_INTERFACE_IRQPIN        (7)
 634       #define CFG_INTERFACE_SHORTERRORS   (0)
 635       #define CFG_INTERFACE_CONFIRMREADY  (0)
 636     #endif
 637
 638     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
 639       #define CFG_INTERFACE
 640       #define CFG_INTERFACE_MAXMSGSIZE    (256)
 641       #define CFG_INTERFACE_PROMPT        "CMD >> "
 642       #define CFG_INTERFACE_SILENTMODE    (0)
 643       #define CFG_INTERFACE_DROPCR        (0)
 644       #define CFG_INTERFACE_ENABLEIRQ     (0)
 645       #define CFG_INTERFACE_IRQPORT       (0)
 646       #define CFG_INTERFACE_IRQPIN        (7)
 647       #define CFG_INTERFACE_SHORTERRORS   (0)
 648       #define CFG_INTERFACE_CONFIRMREADY  (0)
 649       #define CFG_INTERFACE_SHORTERRORS_UNKNOWNCOMMAND    "?"
 650       #define CFG_INTERFACE_SHORTERRORS_TOOMANYARGS       ">"
 651       #define CFG_INTERFACE_SHORTERRORS_TOOFEWARGS        "<"
 652       #define CFG_INTERFACE_CONFIRMREADY_TEXT             "."
 653     #endif
 654
 655     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 656       #define CFG_INTERFACE
 657       #define CFG_INTERFACE_MAXMSGSIZE    (256)
 658       #define CFG_INTERFACE_PROMPT        ">>"
 659       #define CFG_INTERFACE_SILENTMODE    (1)
 660       #define CFG_INTERFACE_DROPCR        (1)
 661       #define CFG_INTERFACE_ENABLEIRQ     (1)
 662       #define CFG_INTERFACE_IRQPORT       (0)
 663       #define CFG_INTERFACE_IRQPIN        (7)
 664       #define CFG_INTERFACE_SHORTERRORS   (1)
 665       #define CFG_INTERFACE_CONFIRMREADY  (0)
 666       #define CFG_INTERFACE_SHORTERRORS_UNKNOWNCOMMAND    "?"
 667       #define CFG_INTERFACE_SHORTERRORS_TOOMANYARGS       ">"
 668       #define CFG_INTERFACE_SHORTERRORS_TOOFEWARGS        "<"
 669       #define CFG_INTERFACE_CONFIRMREADY_TEXT             "."
 670     #endif
 671
 672     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 673       // #define CFG_INTERFACE
 674       #define CFG_INTERFACE_MAXMSGSIZE    (256)
 675       #define CFG_INTERFACE_PROMPT        "CMD >> "
 676       #define CFG_INTERFACE_SILENTMODE    (0)
 677       #define CFG_INTERFACE_DROPCR        (0)
 678       #define CFG_INTERFACE_ENABLEIRQ     (0)
 679       #define CFG_INTERFACE_IRQPORT       (0)
 680       #define CFG_INTERFACE_IRQPIN        (7)
 681       #define CFG_INTERFACE_SHORTERRORS   (0)
 682       #define CFG_INTERFACE_CONFIRMREADY  (0)
 683     #endif
 684
 685     #ifdef CFG_BRD_LPC1343_OLIMEX_P
 686       #define CFG_INTERFACE
 687       #define CFG_INTERFACE_MAXMSGSIZE    (256)
 688       #define CFG_INTERFACE_PROMPT        "LPC-P1343 >> "
 689       #define CFG_INTERFACE_SILENTMODE    (0)
 690       #define CFG_INTERFACE_DROPCR        (0)
 691       #define CFG_INTERFACE_ENABLEIRQ     (0)
 692       #define CFG_INTERFACE_IRQPORT       (0)
 693       #define CFG_INTERFACE_IRQPIN        (7)
 694       #define CFG_INTERFACE_SHORTERRORS   (0)
 695       #define CFG_INTERFACE_CONFIRMREADY  (0)
 696     #endif
 697 /*=========================================================================*/
 698
 699
 700 /*=========================================================================
 701     PWM SETTINGS
 702     -----------------------------------------------------------------------
 703
 704     CFG_PWM                     If this is defined, a basic PWM driver
 705                                 will be included using 16-bit Timer 1 and
 706                                 Pin 1.9 (MAT0) for the PWM output.  In
 707                                 order to allow for a fixed number of
 708                                 pulses to be generated, some PWM-specific
 709                                 code is required in the 16-Bit Timer 1
 710                                 ISR.  See "core/timer16/timer16.c" for
 711                                 more information.
 712     CFG_PWM_DEFAULT_PULSEWIDTH  The default pulse width in ticks
 713     CFG_PWM_DEFAULT_DUTYCYCLE   The default duty cycle in percent
 714
 715     DEPENDENCIES:               PWM output requires the use of 16-bit
 716                                 timer 1 and pin 1.9 (CT16B1_MAT0).
 717     -----------------------------------------------------------------------*/
 718     // #define CFG_PWM
 719     #define CFG_PWM_DEFAULT_PULSEWIDTH  (CFG_CPU_CCLK / 1000)
 720     #define CFG_PWM_DEFAULT_DUTYCYCLE   (50)
 721 /*=========================================================================*/
 722
 723
 724 /*=========================================================================
 725     STEPPER MOTOR SETTINGS
 726     -----------------------------------------------------------------------
 727
 728     CFG_STEPPER                 If this is defined, a simple bi-polar
 729                                 stepper motor will be included for common
 730                                 H-bridge chips like the L293D or SN754410N
 731
 732     DEPENDENCIES:               STEPPER requires the use of pins 3.0-3 and
 733                                 32-bit Timer 0.
 734     -----------------------------------------------------------------------*/
 735     // #define CFG_STEPPER
 736 /*=========================================================================*/
 737
 738
 739 /*=========================================================================
 740     EEPROM
 741     -----------------------------------------------------------------------
 742
 743     CFG_I2CEEPROM             If defined, drivers for the onboard EEPROM
 744                               will be included during build
 745     CFG_I2CEEPROM_SIZE        The number of bytes available on the EEPROM
 746
 747     -----------------------------------------------------------------------*/
 748     #ifdef CFG_BRD_LPC1343_REFDESIGN
 749       #define CFG_I2CEEPROM
 750       #define CFG_I2CEEPROM_SIZE          (3072)
 751     #endif
 752
 753     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 754       // #define CFG_I2CEEPROM
 755       #define CFG_I2CEEPROM_SIZE          (3072)
 756     #endif
 757
 758     #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 759       #define CFG_I2CEEPROM
 760       #define CFG_I2CEEPROM_SIZE          (3072)
 761     #endif
 762
 763     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 764       #define CFG_I2CEEPROM
 765       #define CFG_I2CEEPROM_SIZE          (3072)
 766     #endif
 767
 768     #ifdef CFG_BRD_LPC1343_OLIMEX_P
 769       // #define CFG_I2CEEPROM
 770       #define CFG_I2CEEPROM_SIZE          (3072)
 771     #endif
 772 /*=========================================================================*/
 773
 774
 775 /*=========================================================================
 776     EEPROM MEMORY MAP
 777     -----------------------------------------------------------------------
 778     EEPROM is used to persist certain user modifiable values to make
 779     sure that these changes remain in effect after a reset or hard
 780     power-down.  The addresses in EEPROM for these various system
 781     settings/values are defined below.  The first 256 bytes of EEPROM
 782     are reserved for this (0x0000..0x00FF).
 783
 784     CFG_EEPROM_RESERVED       The last byte of reserved EEPROM memory
 785
 786           EEPROM Address (0x0000..0x00FF)
 787           ===============================
 788           0 1 2 3 4 5 6 7 8 9 A B C D E F
 789     000x  x x x x x x x x . x x . . . . .   Chibi
 790     001x  . . . . . . . . . . . . . . . .
 791     002x  x x x x . . . . . . . . . . . .   UART
 792     003x  x x x x x x x x x x x x x x x x   Touch Screen Calibration
 793     004x  x x x x x x x x x x x x x x . .   Touch Screen Calibration
 794     005x  . . . . . . . . . . . . . . . .
 795     006x  . . . . . . . . . . . . . . . .
 796     007x  . . . . . . . . . . . . . . . .
 797     008x  . . . . . . . . . . . . . . . .
 798     009x  . . . . . . . . . . . . . . . .
 799     00Ax  . . . . . . . . . . . . . . . .
 800     00Bx  . . . . . . . . . . . . . . . .
 801     00Cx  . . . . . . . . . . . . . . . .
 802     00Dx  . . . . . . . . . . . . . . . .
 803     00Ex  . . . . . . . . . . . . . . . .
 804     00Fx  . . . . . . . . . . . . . . . .
 805
 806     -----------------------------------------------------------------------*/
 807     #define CFG_EEPROM_RESERVED                 (0x00FF)              // Protect first 256 bytes of memory
 808     #define CFG_EEPROM_CHIBI_IEEEADDR           (uint16_t)(0x0000)    // 8
 809     #define CFG_EEPROM_CHIBI_SHORTADDR          (uint16_t)(0x0009)    // 2
 810     #define CFG_EEPROM_UART_SPEED               (uint16_t)(0x0020)    // 4
 811     #define CFG_EEPROM_TOUCHSCREEN_CALIBRATED   (uint16_t)(0x0030)    // 1
 812     #define CFG_EEPROM_TOUCHSCREEN_CAL_AN       (uint16_t)(0x0031)    // 4
 813     #define CFG_EEPROM_TOUCHSCREEN_CAL_BN       (uint16_t)(0x0035)    // 4
 814     #define CFG_EEPROM_TOUCHSCREEN_CAL_CN       (uint16_t)(0x0039)    // 4
 815     #define CFG_EEPROM_TOUCHSCREEN_CAL_DN       (uint16_t)(0x003D)    // 4
 816     #define CFG_EEPROM_TOUCHSCREEN_CAL_EN       (uint16_t)(0x0041)    // 4
 817     #define CFG_EEPROM_TOUCHSCREEN_CAL_FN       (uint16_t)(0x0045)    // 4
 818     #define CFG_EEPROM_TOUCHSCREEN_CAL_DIVIDER  (uint16_t)(0x0049)    // 4
 819     #define CFG_EEPROM_TOUCHSCREEN_THRESHHOLD   (uint16_t)(0x004D)    // 1
 820 /*=========================================================================*/
 821
 822
 823 /*=========================================================================
 824     LM75B TEMPERATURE SENSOR
 825     -----------------------------------------------------------------------
 826
 827     CFG_LM75B                 If defined, drivers for an optional LM75B
 828                               temperature sensor will be included during
 829                               build (requires external HW)
 830
 831     -----------------------------------------------------------------------*/
 832     // #define CFG_LM75B
 833 /*=========================================================================*/
 834
 835
 836 /*=========================================================================
 837     CHIBI WIRELESS STACK
 838     -----------------------------------------------------------------------
 839
 840     CFG_CHIBI                   If defined, the CHIBI wireless stack will be
 841                                 included during build.  Requires external HW.
 842     CFG_CHIBI_MODE              The mode to use when receiving and transmitting
 843                                 wireless data.  See chb_drvr.h for possible values
 844     CFG_CHIBI_POWER             The power level to use when transmitting.  See
 845                                 chb_drvr.h for possible values
 846     CFG_CHIBI_CHANNEL           802.15.4 Channel (0 = 868MHz, 1-10 = 915MHz)
 847     CFG_CHIBI_PANID             16-bit PAN Identifier (ex.0x1234)
 848     CFG_CHIBI_PROMISCUOUS       Set to 1 to enabled promiscuous mode or
 849                                 0 to disable it.  If promiscuous mode is
 850                                 enabled be sure to set CFG_CHIBI_BUFFERSIZE
 851                                 to an appropriately large value (ex. 1024)
 852     CFG_CHIBI_BUFFERSIZE        The size of the message buffer in bytes
 853
 854     DEPENDENCIES:               Chibi requires the use of SSP0, 16-bit timer
 855                                 0 and pins 3.1, 3.2, 3.3.  It also requires
 856                                 the presence of CFG_I2CEEPROM.
 857
 858     NOTE:                       These settings are not relevant to all boards!
 859                                 'tools/schematics/AT86RF212LPC1114_v1.6.pdf'
 860                                 show how 'CHIBI' is meant to be connected
 861     -----------------------------------------------------------------------*/
 862     #ifdef CFG_BRD_LPC1343_REFDESIGN
 863       // #define CFG_CHIBI
 864       #define CFG_CHIBI_MODE              (0)                 // OQPSK_868MHZ
 865       #define CFG_CHIBI_POWER             (0xE9)              // CHB_PWR_EU2_3DBM
 866       #define CFG_CHIBI_CHANNEL           (0)                 // 868-868.6 MHz
 867       #define CFG_CHIBI_PANID             (0x1234)
 868       #define CFG_CHIBI_PROMISCUOUS       (0)
 869       #define CFG_CHIBI_BUFFERSIZE        (128)
 870     #endif
 871
 872     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 873       // #define CFG_CHIBI
 874       #define CFG_CHIBI_MODE              (0)                 // OQPSK_868MHZ
 875       #define CFG_CHIBI_POWER             (0xE9)              // CHB_PWR_EU2_3DBM
 876       #define CFG_CHIBI_CHANNEL           (0)                 // 868-868.6 MHz
 877       #define CFG_CHIBI_PANID             (0x1234)
 878       #define CFG_CHIBI_PROMISCUOUS       (0)
 879       #define CFG_CHIBI_BUFFERSIZE        (128)
 880     #endif
 881
 882     #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 883       // #define CFG_CHIBI
 884       #define CFG_CHIBI_MODE              (0)                 // OQPSK_868MHZ
 885       #define CFG_CHIBI_POWER             (0xE9)              // CHB_PWR_EU2_3DBM
 886       #define CFG_CHIBI_CHANNEL           (0)                 // 868-868.6 MHz
 887       #define CFG_CHIBI_PANID             (0x1234)
 888       #define CFG_CHIBI_PROMISCUOUS       (0)
 889       #define CFG_CHIBI_BUFFERSIZE        (128)
 890     #endif
 891
 892     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 893       #define CFG_CHIBI
 894       #define CFG_CHIBI_MODE              (0)                 // OQPSK_868MHZ
 895       #define CFG_CHIBI_POWER             (0xE9)              // CHB_PWR_EU2_3DBM
 896       #define CFG_CHIBI_CHANNEL           (0)                 // 868-868.6 MHz
 897       #define CFG_CHIBI_PANID             (0x1234)
 898       #define CFG_CHIBI_PROMISCUOUS       (0)
 899       #define CFG_CHIBI_BUFFERSIZE        (1024)
 900     #endif
 901
 902     #ifdef CFG_BRD_LPC1343_OLIMEX_P
 903       // #define CFG_CHIBI
 904       #define CFG_CHIBI_MODE              (0)                 // OQPSK_868MHZ
 905       #define CFG_CHIBI_POWER             (0xE9)              // CHB_PWR_EU2_3DBM
 906       #define CFG_CHIBI_CHANNEL           (0)                 // 868-868.6 MHz
 907       #define CFG_CHIBI_PANID             (0x1234)
 908       #define CFG_CHIBI_PROMISCUOUS       (0)
 909       #define CFG_CHIBI_BUFFERSIZE        (128)
 910     #endif
 911 /*=========================================================================*/
 912
 913
 914 /*=========================================================================
 915     TFT LCD
 916     -----------------------------------------------------------------------
 917
 918     CFG_TFTLCD                  If defined, this will cause drivers for
 919                                 a pre-determined LCD screen to be included
 920                                 during build.  Only one LCD driver can be
 921                                 included during the build process (for ex.
 922                                 'drivers/lcd/hw/ILI9325.c')
 923     CFG_TFTLCD_INCLUDESMALLFONTS If set to 1, smallfont support will be
 924                                 included for 3x6, 5x8, 7x8 and 8x8 fonts.
 925                                 This should only be enabled if these small
 926                                 fonts are required since there is already
 927                                 support for larger fonts generated with
 928                                 Dot Factory
 929                                 http://www.pavius.net/downloads/tools/53-the-dot-factory
 930     CFG_TFTLCD_TS_DEFAULTTHRESHOLD  Default minimum threshold to trigger a
 931                                 touch event with the touch screen (and exit
 932                                 from 'tsWaitForEvent' in touchscreen.c).
 933                                 Should be an 8-bit value somewhere between
 934                                 8 and 75 in normal circumstances.  This is
 935                                 the default value and may be overriden by
 936                                 a value stored in EEPROM.
 937     CFG_TFTLCD_TS_KEYPADDELAY   The delay in milliseconds between key
 938                                 presses in dialogue boxes
 939
 940     PIN LAYOUT:                 The pin layout that is used by this driver
 941                                 can be seen in the following schematic:
 942                                 /tools/schematics/Breakout_TFTLCD_ILI9325_v1.3
 943
 944     DEPENDENCIES:               TFTLCD requires the use of pins 1.8, 1.9,
 945                                 1.10, 1.11, 3.3 and 2.1-9.
 946     -----------------------------------------------------------------------*/
 947     #ifdef CFG_BRD_LPC1343_REFDESIGN
 948       // #define CFG_TFTLCD
 949       #define CFG_TFTLCD_INCLUDESMALLFONTS   (0)
 950       #define CFG_TFTLCD_TS_DEFAULTTHRESHOLD (50)
 951       #define CFG_TFTLCD_TS_KEYPADDELAY      (100)
 952     #endif
 953
 954     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 955       // #define CFG_TFTLCD
 956       #define CFG_TFTLCD_INCLUDESMALLFONTS   (0)
 957       #define CFG_TFTLCD_TS_DEFAULTTHRESHOLD (50)
 958       #define CFG_TFTLCD_TS_KEYPADDELAY      (100)
 959     #endif
 960
 961     #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 962       #define CFG_TFTLCD
 963       #define CFG_TFTLCD_INCLUDESMALLFONTS   (0)
 964       #define CFG_TFTLCD_TS_DEFAULTTHRESHOLD (50)
 965       #define CFG_TFTLCD_TS_KEYPADDELAY      (100)
 966     #endif
 967
 968     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 969       // #define CFG_TFTLCD
 970       #define CFG_TFTLCD_INCLUDESMALLFONTS   (0)
 971       #define CFG_TFTLCD_TS_DEFAULTTHRESHOLD (50)
 972       #define CFG_TFTLCD_TS_KEYPADDELAY      (100)
 973     #endif
 974
 975     #ifdef CFG_BRD_LPC1343_OLIMEX_P
 976       // #define CFG_TFTLCD
 977       #define CFG_TFTLCD_INCLUDESMALLFONTS   (0)
 978       #define CFG_TFTLCD_TS_DEFAULTTHRESHOLD (50)
 979       #define CFG_TFTLCD_TS_KEYPADDELAY      (100)
 980     #endif
 981 /*=========================================================================*/
 982
 983
 984 /*=========================================================================
 985     Monochrome/Bitmap Graphic LCDs
 986     -----------------------------------------------------------------------
 987
 988     CFG_ST7565                If defined, this will cause drivers for
 989                               the 128x64 pixel ST7565 LCD to be included
 990     CFG_SSD1306               If defined, this will cause drivers for
 991                               the 128x64 pixel SSD1306 OLED display to be
 992                               included
 993     CFG_SHARPMEM              If defined, this will cause drivers for
 994                               Sharp Memory Displays to be included
 995
 996     DEPENDENCIES:             ST7565 requires the use of pins 2.1-6.
 997     DEPENDENCIES:             SSD1306 requires the use of pins 2.1-6.
 998     DEPENDENCIES:             SHARPMEM requires the use of pins 2.1-4.
 999     -----------------------------------------------------------------------*/
1000     // #define CFG_ST7565
1001     // #define CFG_SSD1306
1002     // #define CFG_SHARPMEM
1003 /*=========================================================================*/
1004
1005
1006 /*=========================================================================
1007     RSA Encryption
1008     -----------------------------------------------------------------------
1009
1010     CFG_RSA                     If defined, support for basic RSA
1011                                 encryption will be included.
1012     CFG_RSA_BITS                Indicates the number of bits used for
1013                                 RSA encryption keys.  To keep code size
1014                                 reasonable, RSA encryption is currently
1015                                 limited to using 64-bit or 32-bit numbers,
1016                                 with 64-bit providing higher security, and
1017                                 32-bit providing smaller encrypted text
1018                                 size.
1019
1020     NOTE:                       Please note that Printf can not be
1021                                 used to display 64-bit values (%lld)!
1022     -----------------------------------------------------------------------*/
1023     // #define CFG_RSA
1024     #define CFG_RSA_BITS                  (32)
1025 /*=========================================================================*/
1026
1027
1028
1029
1030 /*=========================================================================
1031   CONFIG FILE VALIDATION
1032   -------------------------------------------------------------------------
1033   Basic error checking to make sure that incompatible defines are not
1034   enabled at the same time, etc.
1035
1036   =========================================================================*/
1037
1038 #if !defined CFG_BRD_LPC1343_REFDESIGN && \
1039   !defined CFG_BRD_LPC1343_REFDESIGN_MINIMAL && \
1040   !defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB && \
1041   !defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART && \
1042   !defined CFG_BRD_LPC1343_802154USBSTICK && \
1043   !defined CFG_BRD_LPC1343_OLIMEX_P
1044   #error "You must defined a target board (CFG_BRD_LPC1343_REFDESIGN or CFG_BRD_LPC1343_REFDESIGN_MINIMAL or CFG_BRD_LPC1343_TFTLCDSTANDALONE or CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART or CFG_BRD_LPC1343_802154USBSTICK)"
1045 #endif
1046
1047 #if defined CFG_PRINTF_USBCDC && defined CFG_PRINTF_UART
1048   #error "CFG_PRINTF_UART or CFG_PRINTF_USBCDC cannot both be defined at once"
1049 #endif
1050
1051 #if defined CFG_PRINTF_USBCDC && !defined CFG_USBCDC
1052   #error "CFG_PRINTF_CDC requires CFG_USBCDC to be defined as well"
1053 #endif
1054
1055 #if defined CFG_USBCDC && defined CFG_USBHID
1056   #error "Only one USB class can be defined at a time (CFG_USBCDC or CFG_USBHID)"
1057 #endif
1058
1059 #if defined CFG_SSP0_SCKPIN_2_11 && defined CFG_SSP0_SCKPIN_0_6
1060   #error "Only one SCK pin can be defined at a time for SSP0"
1061 #endif
1062
1063 #if !defined CFG_SSP0_SCKPIN_2_11 && !defined CFG_SSP0_SCKPIN_0_6
1064   #error "An SCK pin must be selected for SSP0 (CFG_SSP0_SCKPIN_2_11 or CFG_SSP0_SCKPIN_0_6)"
1065 #endif
1066
1067 #ifdef CFG_INTERFACE
1068   #if !defined CFG_PRINTF_UART && !defined CFG_PRINTF_USBCDC
1069     #error "CFG_PRINTF_UART or CFG_PRINTF_USBCDC must be defined for for CFG_INTERFACE Input/Output"
1070   #endif
1071   #if defined CFG_PRINTF_USBCDC && CFG_INTERFACE_SILENTMODE == 1
1072     #error "CFG_INTERFACE_SILENTMODE typically isn't enabled with CFG_PRINTF_USBCDC"
1073   #endif
1074 #endif
1075
1076 #ifdef CFG_CHIBI
1077   #if !defined CFG_I2CEEPROM
1078     #error "CFG_CHIBI requires CFG_I2CEEPROM to store and retrieve addresses"
1079   #endif
1080   #ifdef CFG_SDCARD
1081     #error "CFG_CHIBI and CFG_SDCARD can not be defined at the same time. Only one SPI block is available on the LPC1343."
1082   #endif
1083   #ifdef CFG_TFTLCD
1084     #error "CFG_CHIBI and CFG_TFTLCD can not be defined at the same time since they both use pins 1.8, 1.9 and 1.10."
1085   #endif
1086   #ifdef CFG_PWM
1087     #error "CFG_CHIBI and CFG_PWM can not be defined at the same time since they both use pin 1.9."
1088   #endif
1089   #if CFG_CHIBI_PROMISCUOUS != 0 && CFG_CHIBI_PROMISCUOUS != 1
1090     #error "CFG_CHIBI_PROMISCUOUS must be equal to either 1 or 0"
1091   #endif
1092 #endif
1093
1094 #ifdef CFG_TFTLCD
1095   #ifdef CFG_ST7565
1096     #error "CFG_TFTLCD and CFG_ST7565 can not be defined at the same time."
1097   #endif
1098   #ifdef CFG_SSD1306
1099     #error "CFG_TFTLCD and CFG_SSD1306 can not be defined at the same time."
1100   #endif
1101   #ifdef CFG_SHARPMEM
1102     #error "CFG_TFTLCD and CFG_SHARPMEM can not be defined at the same time."
1103   #endif
1104   #ifdef CFG_PWM
1105     #error "CFG_TFTLCD and CFG_PWM can not be defined at the same time since they both use pin 1.9."
1106   #endif
1107   #if !defined CFG_I2CEEPROM
1108     #error "CFG_TFTLCD requires CFG_I2CEEPROM to store and retrieve configuration settings"
1109   #endif
1110 #endif
1111
1112 #ifdef CFG_SDCARD
1113   #ifdef CFG_STEPPER
1114     #error  "CFG_SDCARD and CFG_STEPPER can not be defined at the same time since they both use pin 3.0."
1115   #endif
1116 #endif
1117
1118 #ifdef CFG_ST7565
1119   #ifdef CFG_SSD1306
1120     #error "CFG_ST7565 and CFG_SSD1306 can not be defined at the same time"
1121   #endif
1122 #endif
1123
1124 #ifdef CFG_RSA
1125   #if CFG_RSA_BITS != 64 && CFG_RSA_BITS != 32
1126     #error "CFG_RSA_BITS must be equal to either 32 or 64."
1127   #endif
1128 #endif
1129
1130 #endif