projectconfig.h

   1 /**************************************************************************/
   2 /*!
   3     @file     projectconfig.h
   4     @author   K. Townsend (microBuilder.eu)
   5
   6     @section LICENSE
   7
   8     Software License Agreement (BSD License)
   9
  10     Copyright (c) 2010, microBuilder SARL
  11     All rights reserved.
  12
  13     Redistribution and use in source and binary forms, with or without
  14     modification, are permitted provided that the following conditions are met:
  15     1. Redistributions of source code must retain the above copyright
  16     notice, this list of conditions and the following disclaimer.
  17     2. Redistributions in binary form must reproduce the above copyright
  18     notice, this list of conditions and the following disclaimer in the
  19     documentation and/or other materials provided with the distribution.
  20     3. Neither the name of the copyright holders nor the
  21     names of its contributors may be used to endorse or promote products
  22     derived from this software without specific prior written permission.
  23
  24     THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS ''AS IS'' AND ANY
  25     EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
  26     WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
  27     DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER BE LIABLE FOR ANY
  28     DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
  29     (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
  30     LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
  31     ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
  32     (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
  33     SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  34 */
  35 /**************************************************************************/
  36
  37 #ifndef _PROJECTCONFIG_H_
  38 #define _PROJECTCONFIG_H_
  39
  40 #include "lpc134x.h"
  41 #include "sysdefs.h"
  42
  43 /*=========================================================================
  44     BOARD SELECTION
  45
  46     Because several boards use this code library with sometimes slightly
  47     different pin configuration, you will need to specify which board you
  48     are using by enabling one of the following definitions. The code base
  49     will then try to configure itself accordingly for that board.
  50
  51     CFG_BRD_LPC1343_REFDESIGN
  52     =========================
  53
  54         microBuilder.eu LPC1343 Reference Design base board with
  55         on-board peripherals initialised (EEPROM, USB or UART CLI, etc.)
  56
  57                 This is the recommended starting point for new development
  58                 since it makes it easy to send printf output to USB CDC, access
  59                 the on-board EEPROM, etc.
  60
  61     CFG_BRD_LPC1343_REFDESIGN_MINIMAL
  62     =================================
  63
  64         microBuilder.eu LPC1343 Reference Design base board with
  65         only the most common peripherals initialised by default.
  66
  67         Results in smallest code since EEPROM, USB, etc., are not
  68         initialised on startup.  By default, only the following
  69         peripherals are initialised by systemInit():
  70
  71               - CPU (Configures the PLL, etc.)
  72               - GPIO
  73               - SysTick Timer
  74               - UART (with printf support) *
  75
  76         * Can be removed to save 0.8kb in debug and 0.3 kb in
  77         release. Comment out 'CFG_PRINTF_UART' to disable it.
  78
  79         The code size can be further reduced by several KB by removing
  80         any IRQ Handlers that are not used.  The I2C IRQHandler, for
  81         example, uses ~1KB of flash in debug and ~400KB in release mode,
  82         but because it is referenced in the startup code it is always
  83         included even if I2C is never used in the project.
  84
  85         Other IRQ Handlers that you might be able to comment out
  86         to save some space are:
  87
  88         IRQ Handler               Debug   Release
  89         ------------------------- ------  -------
  90         I2C_IRQHandler            1160 b    400 b
  91         SSP_IRQHandler             160 b     76 b
  92         UART_IRQHandler            246 b    116 b
  93         WAKEUP_IRQHandler          160 b    100 b
  94         WDT_IRQHandler              50 b     28 b
  95
  96     CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
  97     ====================================
  98
  99         microBuilder.eu/Adafruit Stand-Alone "Smart LCD" with USB enabled
 100         for the CLI interface.
 101
 102     CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 103     =====================================
 104
 105         microBuilder.eu/Adafruit Stand-Alone "Smart LCD" with UART enabled
 106         for the CLI interface.
 107
 108     CFG_BRD_LPC1343_802154USBSTICK
 109     ==============================
 110
 111         microBuilder.eu USB stick 802.15.4 868/915MHz RF transceiver
 112
 113     -----------------------------------------------------------------------*/
 114     #define CFG_BRD_LPC1343_REFDESIGN
 115     // #define CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 116     // #define CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
 117     // #define CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 118     // #define CFG_BRD_LPC1343_802154USBSTICK
 119 /*=========================================================================*/
 120
 121
 122 /**************************************************************************
 123     PIN USAGE
 124     -----------------------------------------------------------------------
 125     This table tries to give an indication of which GPIO pins and
 126     peripherals are used by the available drivers and SW examples.  Only
 127     dedicated GPIO pins available on the LPC1343 Reference Board are shown
 128     below.  Any unused peripheral blocks like I2C, SSP, ADC, etc., can
 129     also be used as GPIO if they are available.
 130
 131                 PORT 1        PORT 2                PORT 3
 132                 =========     =================     =======
 133                 8 9 10 11     1 2 3 4 5 6 7 8 9     0 1 2 3
 134
 135     SDCARD      . .  .  .     . . . . . . . . .     X . . .
 136     PWM         . X  .  .     . . . . . . . . .     . . . .
 137     STEPPER     . .  .  .     . . . . . . . . .     X X X X
 138     CHIBI       X X  X  .     . . . . . . . . .     . . . .
 139     ILI9325/8   X X  X  X     X X X X X X X X X     . . . X
 140     ST7565      X X  X  X     X X X X X X X X X     . . . X
 141     ST7735      . .  .  .     X X X X X X . . .     . . . .
 142     SHARPMEM    . .  .  .     X X X X . . . . .     . . . .
 143     SSD1306     . .  .  .     X X X . X X . . .     . . . .
 144     SSD1351     . .  .  .     X X X X X . . . .     . . . .
 145     MCP121      . .  .  .     . . . . . . . . .     . X . .
 146
 147                 TIMERS                    SSP     ADC         UART
 148                 ======================    ===     =======     ====
 149                 16B0  16B1  32B0  32B1    0       0 1 2 3     0
 150
 151     SDCARD      .     .     .     .       X       . . . .     .
 152     PWM         .     X     .     .       .       . . . .     .
 153     PMU [1]     .     .     X     .       .       . . . .     .
 154     USB         .     .     .     X       .       . . . .     .
 155     STEPPER     .     .     X     .       .       . . . .     .
 156     CHIBI       x     .     .     .       X       . . . .     .
 157     ILI9325/8   .     .     .     .       .       X X X X     .
 158     ST7565      .     .     .     .       .       X X X X     .
 159     ST7535      .     .     .     .       .       . . . .     .
 160     SHARPMEM    .     .     .     .       .       . . . .     .
 161     SSD1306     .     .     .     .       .       . . . .     .
 162     INTERFACE   .     .     .     .       .       . . . .     X[2]
 163
 164     [1]  PMU uses 32-bit Timer 0 for SW wakeup from deep-sleep.  This timer
 165          can safely be used by other peripherals, but may need to be
 166          reconfigured when you wakeup from deep-sleep.
 167     [2]  INTERFACE can be configured to use either USBCDC or UART
 168
 169  **************************************************************************/
 170
 171
 172 /**************************************************************************
 173     I2C Addresses
 174     -----------------------------------------------------------------------
 175     The following addresses are used by the different I2C sensors included
 176     in the code base [1]
 177
 178                                 HEX       BINARY
 179                                 ====      ========
 180     ISL12022M (RTC)             0xDE      1101111x
 181     ISL12022M (SRAM)            0xAE      1010111x
 182     LM75B                       0x90      1001000x
 183     MCP24AA                     0xA0      1010000x
 184     MCP4725                     0xC0      1100000x
 185     TSL2561                     0x72      0111001x
 186     TCS3414                     0x72      0111001x
 187
 188     [1]  Alternative addresses may exists, but the addresses listed in this
 189          table are the values used in the code base
 190
 191  **************************************************************************/
 192
 193
 194 /*=========================================================================
 195     FIRMWARE VERSION SETTINGS
 196     -----------------------------------------------------------------------*/
 197     #define CFG_FIRMWARE_VERSION_MAJOR            (0)
 198     #define CFG_FIRMWARE_VERSION_MINOR            (9)
 199     #define CFG_FIRMWARE_VERSION_REVISION         (8)
 200 /*=========================================================================*/
 201
 202
 203 /*=========================================================================
 204     CORE CPU SETTINGS
 205     -----------------------------------------------------------------------
 206
 207     CFG_CPU_CCLK    Value is for reference only.  'core/cpu/cpu.c' must
 208                     be modified to change the clock speed, but the value
 209                     should be indicated here since CFG_CPU_CCLK is used by
 210                     other peripherals to determine timing.
 211
 212     -----------------------------------------------------------------------*/
 213     #define CFG_CPU_CCLK                (72000000)  // 1 tick = 13.88nS
 214 /*=========================================================================*/
 215
 216
 217 /*=========================================================================
 218     SYSTICK TIMER
 219     -----------------------------------------------------------------------
 220
 221     CFG_SYSTICK_DELAY_IN_MS   The number of milliseconds between each tick
 222                               of the systick timer.
 223
 224     -----------------------------------------------------------------------*/
 225     #define CFG_SYSTICK_DELAY_IN_MS     (1)
 226 /*=========================================================================*/
 227
 228
 229 /*=========================================================================
 230     ALTERNATE RESET PIN
 231     -----------------------------------------------------------------------
 232
 233     CFG_ALTRESET        If defined, indicates that a GPIO pin should be
 234                         configured as an alternate reset pin in addition
 235                         to the dedicated reset pin.
 236     CFG_ALTRESET_PORT   The GPIO port where the alt reset pin is located
 237     CFG_ALTRESET_PIN    The GPIO pin where the alt reset pin is located
 238
 239     -----------------------------------------------------------------------*/
 240     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 241       #define CFG_ALTRESET
 242       #define CFG_ALTRESET_PORT         (1)
 243       #define CFG_ALTRESET_PIN          (5)   // P1.5 = RTS
 244     #endif
 245 /*=========================================================================*/
 246
 247
 248 /*=========================================================================
 249     UART
 250     -----------------------------------------------------------------------
 251
 252     CFG_UART_BAUDRATE         The default UART speed.  This value is used
 253                               when initialising UART, and should be a
 254                               standard value like 57600, 9600, etc.
 255                               NOTE: This value may be overridden if
 256                               another value is stored in EEPROM!
 257     CFG_UART_BUFSIZE          The length in bytes of the UART RX FIFO. This
 258                               will determine the maximum number of received
 259                               characters to store in memory.
 260
 261     -----------------------------------------------------------------------*/
 262     #ifdef CFG_BRD_LPC1343_REFDESIGN
 263       #define CFG_UART_BAUDRATE           (115200)
 264       #define CFG_UART_BUFSIZE            (512)
 265     #endif
 266
 267     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 268       #define CFG_UART_BAUDRATE           (115200)
 269       #define CFG_UART_BUFSIZE            (512)
 270     #endif
 271
 272     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
 273       #define CFG_UART_BAUDRATE           (115200)
 274       #define CFG_UART_BUFSIZE            (512)
 275     #endif
 276
 277     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 278       #define CFG_UART_BAUDRATE           (57600)
 279       #define CFG_UART_BUFSIZE            (512)
 280     #endif
 281
 282     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 283       #define CFG_UART_BAUDRATE           (115200)
 284       #define CFG_UART_BUFSIZE            (512)
 285     #endif
 286 /*=========================================================================*/
 287
 288
 289 /*=========================================================================
 290     SSP
 291     -----------------------------------------------------------------------
 292
 293     CFG_SSP0_SCKPIN_2_11      Indicates which pin should be used for SCK0
 294     CFG_SSP0_SCKPIN_0_6
 295
 296     -----------------------------------------------------------------------*/
 297     #ifdef CFG_BRD_LPC1343_REFDESIGN
 298       #define CFG_SSP0_SCKPIN_2_11
 299       // #define CFG_SSP0_SCKPIN_0_6
 300     #endif
 301
 302     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 303       #define CFG_SSP0_SCKPIN_2_11
 304       // #define CFG_SSP0_SCKPIN_0_6
 305     #endif
 306
 307     #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 308       #define CFG_SSP0_SCKPIN_2_11
 309       // #define CFG_SSP0_SCKPIN_0_6
 310     #endif
 311
 312     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 313       // #define CFG_SSP0_SCKPIN_2_11
 314       #define CFG_SSP0_SCKPIN_0_6
 315     #endif
 316 /*=========================================================================*/
 317
 318
 319 /*=========================================================================
 320     ON-BOARD LED
 321     -----------------------------------------------------------------------
 322
 323     CFG_LED_PORT              The port for the on board LED
 324     CFG_LED_PIN               The pin for the on board LED
 325     CFG_LED_ON                The pin state to turn the LED on (0 = low, 1 = high)
 326     CFG_LED_OFF               The pin state to turn the LED off (0 = low, 1 = high)
 327
 328     -----------------------------------------------------------------------*/
 329     #ifdef CFG_BRD_LPC1343_REFDESIGN
 330       #define CFG_LED_PORT                (2)
 331       #define CFG_LED_PIN                 (10)
 332       #define CFG_LED_ON                  (0)
 333       #define CFG_LED_OFF                 (1)
 334     #endif
 335
 336     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 337       #define CFG_LED_PORT                (2)
 338       #define CFG_LED_PIN                 (10)
 339       #define CFG_LED_ON                  (0)
 340       #define CFG_LED_OFF                 (1)
 341     #endif
 342
 343     #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 344       #define CFG_LED_PORT                (2)
 345       #define CFG_LED_PIN                 (10)
 346       #define CFG_LED_ON                  (0)
 347       #define CFG_LED_OFF                 (1)
 348     #endif
 349
 350     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 351       #define CFG_LED_PORT                (3)
 352       #define CFG_LED_PIN                 (2)
 353       #define CFG_LED_ON                  (0)
 354       #define CFG_LED_OFF                 (1)
 355     #endif
 356 /*=========================================================================*/
 357
 358
 359 /*=========================================================================
 360     MICRO-SD CARD
 361     -----------------------------------------------------------------------
 362
 363     CFG_SDCARD                If this field is defined SD Card and FAT32
 364                               file system support will be included
 365     CFG_SDCARD_READONLY       If this is set to 1, all commands to
 366                               write to the SD card will be removed
 367                               saving some flash space.
 368     CFG_SDCARD_CDPORT         The card detect port number
 369     CFG_SDCARD_CDPIN          The card detect pin number
 370
 371     NOTE:                     All config settings for FAT32 are defined
 372                               in ffconf.h
 373
 374     BENCHMARK:                With SPI set to 6.0MHz, FATFS can read
 375                               ~300KB/s (w/512 byte read buffer)
 376
 377     PIN LAYOUT:               The pin layout that is used by this driver
 378                               can be seen in the following schematic:
 379                               /tools/schematics/Breakout_TFTLCD_ILI9325_v1.3
 380
 381     DEPENDENCIES:             SDCARD requires the use of SSP0.
 382     -----------------------------------------------------------------------*/
 383     #ifdef CFG_BRD_LPC1343_REFDESIGN
 384       // #define CFG_SDCARD
 385       #define CFG_SDCARD_READONLY         (1)   // Must be 0 or 1
 386       #define CFG_SDCARD_CDPORT           (3)
 387       #define CFG_SDCARD_CDPIN            (0)
 388     #endif
 389
 390     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 391       // #define CFG_SDCARD
 392       #define CFG_SDCARD_READONLY         (1)   // Must be 0 or 1
 393       #define CFG_SDCARD_CDPORT           (3)
 394       #define CFG_SDCARD_CDPIN            (0)
 395     #endif
 396
 397     #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 398       #define CFG_SDCARD
 399       #define CFG_SDCARD_READONLY         (1)   // Must be 0 or 1
 400       #define CFG_SDCARD_CDPORT           (3)
 401       #define CFG_SDCARD_CDPIN            (0)
 402     #endif
 403
 404     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 405       // #define CFG_SDCARD
 406       #define CFG_SDCARD_READONLY         (1)   // Must be 0 or 1
 407       #define CFG_SDCARD_CDPORT           (3)
 408       #define CFG_SDCARD_CDPIN            (0)
 409     #endif
 410 /*=========================================================================*/
 411
 412
 413 /*=========================================================================
 414     USB
 415     -----------------------------------------------------------------------
 416
 417     CFG_USBHID                If this field is defined USB HID support will
 418                               be included.  Currently uses ROM-based USB HID
 419     CFG_USBCDC                If this field is defined USB CDC support will
 420                               be included, with the USB Serial Port speed
 421                               set to 115200 BPS by default
 422     CFG_USBCDC_BAUDRATE       The default TX/RX speed.  This value is used
 423                               when initialising USBCDC, and should be a
 424                               standard value like 57600, 9600, etc.
 425     CFG_USBCDC_INITTIMEOUT    The maximum delay in milliseconds to wait for
 426                               USB to connect.  Must be a multiple of 10!
 427     CFG_USBCDC_BUFFERSIZE     Size of the buffer (in bytes) that stores
 428                               printf data until it can be sent out in
 429                               64 byte frames.  The buffer is required since
 430                               only one frame per ms can be sent using USB
 431                               CDC (see 'puts' in systeminit.c).
 432
 433     -----------------------------------------------------------------------*/
 434     #define CFG_USB_VID                   (0x239A)
 435     #define CFG_USB_PID                   (0x1002)
 436
 437     #ifdef CFG_BRD_LPC1343_REFDESIGN
 438       // #define CFG_USBHID
 439       #define CFG_USBCDC
 440       #define CFG_USBCDC_BAUDRATE         (115200)
 441       #define CFG_USBCDC_INITTIMEOUT      (5000)
 442       #define CFG_USBCDC_BUFFERSIZE       (256)
 443     #endif
 444
 445     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 446       // #define CFG_USBHID
 447       // #define CFG_USBCDC
 448       #define CFG_USBCDC_BAUDRATE         (115200)
 449       #define CFG_USBCDC_INITTIMEOUT      (5000)
 450       #define CFG_USBCDC_BUFFERSIZE       (256)
 451     #endif
 452
 453     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
 454       // #define CFG_USBHID
 455       #define CFG_USBCDC
 456       #define CFG_USBCDC_BAUDRATE         (115200)
 457       #define CFG_USBCDC_INITTIMEOUT      (5000)
 458       #define CFG_USBCDC_BUFFERSIZE       (256)
 459     #endif
 460
 461     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 462       // #define CFG_USBHID
 463       // #define CFG_USBCDC
 464       #define CFG_USBCDC_BAUDRATE         (57600)
 465       #define CFG_USBCDC_INITTIMEOUT      (5000)
 466       #define CFG_USBCDC_BUFFERSIZE       (256)
 467     #endif
 468
 469     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 470       // #define CFG_USBHID
 471       #define CFG_USBCDC
 472       #define CFG_USBCDC_BAUDRATE         (115200)
 473       #define CFG_USBCDC_INITTIMEOUT      (5000)
 474       #define CFG_USBCDC_BUFFERSIZE       (256)
 475     #endif
 476 /*=========================================================================*/
 477
 478
 479 /*=========================================================================
 480     PRINTF REDIRECTION
 481     -----------------------------------------------------------------------
 482
 483     CFG_PRINTF_UART           Will cause all printf statements to be
 484                               redirected to UART
 485     CFG_PRINTF_USBCDC         Will cause all printf statements to be
 486                               redirect to USB Serial
 487     CFG_PRINTF_NEWLINE        This is typically "\r\n" for Windows or
 488                               "\n" for *nix
 489
 490     Note: If no printf redirection definitions are present, all printf
 491     output will be ignored.
 492     -----------------------------------------------------------------------*/
 493     #ifdef CFG_BRD_LPC1343_REFDESIGN
 494       // #define CFG_PRINTF_UART
 495       #define CFG_PRINTF_USBCDC
 496       #define CFG_PRINTF_NEWLINE          "\r\n"
 497     #endif
 498
 499     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 500       #define CFG_PRINTF_UART
 501       // #define CFG_PRINTF_USBCDC
 502       #define CFG_PRINTF_NEWLINE          "\r\n"
 503     #endif
 504
 505     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
 506       // #define CFG_PRINTF_UART
 507       #define CFG_PRINTF_USBCDC
 508       #define CFG_PRINTF_NEWLINE          "\r\n"
 509     #endif
 510
 511     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 512       #define CFG_PRINTF_UART
 513       // #define CFG_PRINTF_USBCDC
 514       #define CFG_PRINTF_NEWLINE          "\n"
 515     #endif
 516
 517     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 518       // #define CFG_PRINTF_UART
 519       #define CFG_PRINTF_USBCDC
 520       #define CFG_PRINTF_NEWLINE          "\r\n"
 521     #endif
 522 /*=========================================================================*/
 523
 524
 525 /*=========================================================================
 526     COMMAND LINE INTERFACE
 527     -----------------------------------------------------------------------
 528
 529     CFG_INTERFACE             If this field is defined the UART or USBCDC
 530                               based command-line interface will be included
 531     CFG_INTERFACE_MAXMSGSIZE  The maximum number of bytes to accept for an
 532                               incoming command
 533     CFG_INTERFACE_PROMPT      The command prompt to display at the start
 534                               of every new data entry line
 535     CFG_INTERFACE_SILENTMODE  If this is set to 1 only text generated in
 536                               response to commands will be send to the
 537                               output buffer.  The command prompt will not
 538                               be displayed and incoming text will not be
 539                               echoed back to the output buffer (allowing
 540                               you to see the text you have input).  This
 541                               is normally only desirable in a situation
 542                               where another MCU is communicating with
 543                               the LPC1343.
 544     CFG_INTERFACE_DROPCR      If this is set to 1 all incoming \r
 545                               characters will be dropped
 546     CFG_INTERFACE_ENABLEIRQ   If this is set to 1 the IRQ pin will be
 547                               set high when a command starts executing
 548                               and will go low when the command has
 549                               finished executing or the LCD is not busy.
 550                               This allows another device to know when a
 551                               new command can safely be sent.
 552     CFG_INTERFACE_IRQPORT     The gpio port for the IRQ/busy pin
 553     CFG_INTERFACE_IRQPIN      The gpio pin number for the IRQ/busy pin
 554     CFG_INTERFACE_SHORTERRORS If this is enabled only short 1 character
 555                               error messages will be returned (followed
 556                               by CFG_PRINTF_NEWLINE), rather than more
 557                               verbose error messages.  The specific
 558                               characters used are defined below.
 559     CFG_INTERFACE_CONFIRMREADY  If this is set to 1 a text confirmation
 560                               will be sent when the command prompt is
 561                               ready for a new command.  This is in
 562                               addition to CFG_INTERFACE_ENABLEIRQ if
 563                               this is also enabled.  The character used
 564                               is defined below.
 565
 566     NOTE:                     The command-line interface will use either
 567                               USB-CDC or UART depending on whether
 568                               CFG_PRINTF_UART or CFG_PRINTF_USBCDC are
 569                               selected.
 570     -----------------------------------------------------------------------*/
 571     #ifdef CFG_BRD_LPC1343_REFDESIGN
 572       #define CFG_INTERFACE
 573       #define CFG_INTERFACE_MAXMSGSIZE    (256)
 574       #define CFG_INTERFACE_PROMPT        "LPC1343 >> "
 575       #define CFG_INTERFACE_SILENTMODE    (0)
 576       #define CFG_INTERFACE_DROPCR        (0)
 577       #define CFG_INTERFACE_ENABLEIRQ     (0)
 578       #define CFG_INTERFACE_IRQPORT       (0)
 579       #define CFG_INTERFACE_IRQPIN        (7)
 580       #define CFG_INTERFACE_SHORTERRORS   (0)
 581       #define CFG_INTERFACE_CONFIRMREADY  (0)
 582     #endif
 583
 584     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 585       // #define CFG_INTERFACE
 586       #define CFG_INTERFACE_MAXMSGSIZE    (256)
 587       #define CFG_INTERFACE_PROMPT        "LPC1343 >> "
 588       #define CFG_INTERFACE_SILENTMODE    (0)
 589       #define CFG_INTERFACE_DROPCR        (0)
 590       #define CFG_INTERFACE_ENABLEIRQ     (0)
 591       #define CFG_INTERFACE_IRQPORT       (0)
 592       #define CFG_INTERFACE_IRQPIN        (7)
 593       #define CFG_INTERFACE_SHORTERRORS   (0)
 594       #define CFG_INTERFACE_CONFIRMREADY  (0)
 595     #endif
 596
 597     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
 598       #define CFG_INTERFACE
 599       #define CFG_INTERFACE_MAXMSGSIZE    (256)
 600       #define CFG_INTERFACE_PROMPT        "CMD >> "
 601       #define CFG_INTERFACE_SILENTMODE    (0)
 602       #define CFG_INTERFACE_DROPCR        (0)
 603       #define CFG_INTERFACE_ENABLEIRQ     (0)
 604       #define CFG_INTERFACE_IRQPORT       (0)
 605       #define CFG_INTERFACE_IRQPIN        (7)
 606       #define CFG_INTERFACE_SHORTERRORS   (0)
 607       #define CFG_INTERFACE_CONFIRMREADY  (0)
 608       #define CFG_INTERFACE_SHORTERRORS_UNKNOWNCOMMAND    "?"
 609       #define CFG_INTERFACE_SHORTERRORS_TOOMANYARGS       ">"
 610       #define CFG_INTERFACE_SHORTERRORS_TOOFEWARGS        "<"
 611       #define CFG_INTERFACE_CONFIRMREADY_TEXT             "."
 612     #endif
 613
 614     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 615       #define CFG_INTERFACE
 616       #define CFG_INTERFACE_MAXMSGSIZE    (256)
 617       #define CFG_INTERFACE_PROMPT        ">>"
 618       #define CFG_INTERFACE_SILENTMODE    (1)
 619       #define CFG_INTERFACE_DROPCR        (1)
 620       #define CFG_INTERFACE_ENABLEIRQ     (1)
 621       #define CFG_INTERFACE_IRQPORT       (0)
 622       #define CFG_INTERFACE_IRQPIN        (7)
 623       #define CFG_INTERFACE_SHORTERRORS   (1)
 624       #define CFG_INTERFACE_CONFIRMREADY  (0)
 625       #define CFG_INTERFACE_SHORTERRORS_UNKNOWNCOMMAND    "?"
 626       #define CFG_INTERFACE_SHORTERRORS_TOOMANYARGS       ">"
 627       #define CFG_INTERFACE_SHORTERRORS_TOOFEWARGS        "<"
 628       #define CFG_INTERFACE_CONFIRMREADY_TEXT             "."
 629     #endif
 630
 631     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 632       // #define CFG_INTERFACE
 633       #define CFG_INTERFACE_MAXMSGSIZE    (256)
 634       #define CFG_INTERFACE_PROMPT        "CMD >> "
 635       #define CFG_INTERFACE_SILENTMODE    (0)
 636       #define CFG_INTERFACE_DROPCR        (0)
 637       #define CFG_INTERFACE_ENABLEIRQ     (0)
 638       #define CFG_INTERFACE_IRQPORT       (0)
 639       #define CFG_INTERFACE_IRQPIN        (7)
 640       #define CFG_INTERFACE_SHORTERRORS   (0)
 641       #define CFG_INTERFACE_CONFIRMREADY  (0)
 642     #endif
 643 /*=========================================================================*/
 644
 645
 646 /*=========================================================================
 647     PWM SETTINGS
 648     -----------------------------------------------------------------------
 649
 650     CFG_PWM                     If this is defined, a basic PWM driver
 651                                 will be included using 16-bit Timer 1 and
 652                                 Pin 1.9 (MAT0) for the PWM output.  In
 653                                 order to allow for a fixed number of
 654                                 pulses to be generated, some PWM-specific
 655                                 code is required in the 16-Bit Timer 1
 656                                 ISR.  See "core/timer16/timer16.c" for
 657                                 more information.
 658     CFG_PWM_DEFAULT_PULSEWIDTH  The default pulse width in ticks
 659     CFG_PWM_DEFAULT_DUTYCYCLE   The default duty cycle in percent
 660
 661     DEPENDENCIES:               PWM output requires the use of 16-bit
 662                                 timer 1 and pin 1.9 (CT16B1_MAT0).
 663     -----------------------------------------------------------------------*/
 664     // #define CFG_PWM
 665     #define CFG_PWM_DEFAULT_PULSEWIDTH  (CFG_CPU_CCLK / 1000)
 666     #define CFG_PWM_DEFAULT_DUTYCYCLE   (50)
 667 /*=========================================================================*/
 668
 669
 670 /*=========================================================================
 671     STEPPER MOTOR SETTINGS
 672     -----------------------------------------------------------------------
 673
 674     CFG_STEPPER                 If this is defined, a simple bi-polar
 675                                 stepper motor will be included for common
 676                                 H-bridge chips like the L293D or SN754410N
 677
 678     DEPENDENCIES:               STEPPER requires the use of pins 3.0-3 and
 679                                 32-bit Timer 0.
 680     -----------------------------------------------------------------------*/
 681     // #define CFG_STEPPER
 682 /*=========================================================================*/
 683
 684
 685 /*=========================================================================
 686     EEPROM
 687     -----------------------------------------------------------------------
 688
 689     CFG_I2CEEPROM             If defined, drivers for the onboard EEPROM
 690                               will be included during build
 691     CFG_I2CEEPROM_SIZE        The number of bytes available on the EEPROM
 692
 693     -----------------------------------------------------------------------*/
 694     #ifdef CFG_BRD_LPC1343_REFDESIGN
 695       #define CFG_I2CEEPROM
 696       #define CFG_I2CEEPROM_SIZE          (3072)
 697     #endif
 698
 699     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 700       // #define CFG_I2CEEPROM
 701       #define CFG_I2CEEPROM_SIZE          (3072)
 702     #endif
 703
 704     #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 705       #define CFG_I2CEEPROM
 706       #define CFG_I2CEEPROM_SIZE          (3072)
 707     #endif
 708
 709     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 710       #define CFG_I2CEEPROM
 711       #define CFG_I2CEEPROM_SIZE          (3072)
 712     #endif
 713 /*=========================================================================*/
 714
 715
 716 /*=========================================================================
 717     EEPROM MEMORY MAP
 718     -----------------------------------------------------------------------
 719     EEPROM is used to persist certain user modifiable values to make
 720     sure that these changes remain in effect after a reset or hard
 721     power-down.  The addresses in EEPROM for these various system
 722     settings/values are defined below.  The first 256 bytes of EEPROM
 723     are reserved for this (0x0000..0x00FF).
 724
 725     CFG_EEPROM_RESERVED       The last byte of reserved EEPROM memory
 726
 727           EEPROM Address (0x0000..0x00FF)
 728           ===============================
 729           0 1 2 3 4 5 6 7 8 9 A B C D E F
 730     000x  x x x x x x x x . x x . . . . .   Chibi
 731     001x  . . . . . . . . . . . . . . . .
 732     002x  x x x x . . . . . . . . . . . .   UART
 733     003x  x x x x x x x x x x x x x x x x   Touch Screen Calibration
 734     004x  x x x x x x x x x x x x x x . .   Touch Screen Calibration
 735     005x  . . . . . . . . . . . . . . . .
 736     006x  . . . . . . . . . . . . . . . .
 737     007x  . . . . . . . . . . . . . . . .
 738     008x  . . . . . . . . . . . . . . . .
 739     009x  . . . . . . . . . . . . . . . .
 740     00Ax  . . . . . . . . . . . . . . . .
 741     00Bx  . . . . . . . . . . . . . . . .
 742     00Cx  . . . . . . . . . . . . . . . .
 743     00Dx  . . . . . . . . . . . . . . . .
 744     00Ex  . . . . . . . . . . . . . . . .
 745     00Fx  . . . . . . . . . . . . . . . .
 746
 747     -----------------------------------------------------------------------*/
 748     #define CFG_EEPROM_RESERVED                 (0x00FF)              // Protect first 256 bytes of memory
 749     #define CFG_EEPROM_CHIBI_IEEEADDR           (uint16_t)(0x0000)    // 8
 750     #define CFG_EEPROM_CHIBI_SHORTADDR          (uint16_t)(0x0009)    // 2
 751     #define CFG_EEPROM_UART_SPEED               (uint16_t)(0x0020)    // 4
 752     #define CFG_EEPROM_TOUCHSCREEN_CALIBRATED   (uint16_t)(0x0030)    // 1
 753     #define CFG_EEPROM_TOUCHSCREEN_CAL_AN       (uint16_t)(0x0031)    // 4
 754     #define CFG_EEPROM_TOUCHSCREEN_CAL_BN       (uint16_t)(0x0035)    // 4
 755     #define CFG_EEPROM_TOUCHSCREEN_CAL_CN       (uint16_t)(0x0039)    // 4
 756     #define CFG_EEPROM_TOUCHSCREEN_CAL_DN       (uint16_t)(0x003D)    // 4
 757     #define CFG_EEPROM_TOUCHSCREEN_CAL_EN       (uint16_t)(0x0041)    // 4
 758     #define CFG_EEPROM_TOUCHSCREEN_CAL_FN       (uint16_t)(0x0045)    // 4
 759     #define CFG_EEPROM_TOUCHSCREEN_CAL_DIVIDER  (uint16_t)(0x0049)    // 4
 760     #define CFG_EEPROM_TOUCHSCREEN_THRESHHOLD   (uint16_t)(0x004D)    // 1
 761 /*=========================================================================*/
 762
 763
 764 /*=========================================================================
 765     LM75B TEMPERATURE SENSOR
 766     -----------------------------------------------------------------------
 767
 768     CFG_LM75B                 If defined, drivers for an optional LM75B
 769                               temperature sensor will be included during
 770                               build (requires external HW)
 771
 772     -----------------------------------------------------------------------*/
 773     // #define CFG_LM75B
 774 /*=========================================================================*/
 775
 776
 777 /*=========================================================================
 778     CHIBI WIRELESS STACK
 779     -----------------------------------------------------------------------
 780
 781     CFG_CHIBI                   If defined, the CHIBI wireless stack will be
 782                                 included during build.  Requires external HW.
 783     CFG_CHIBI_MODE              The mode to use when receiving and transmitting
 784                                 wireless data.  See chb_drvr.h for possible values
 785     CFG_CHIBI_POWER             The power level to use when transmitting.  See
 786                                 chb_drvr.h for possible values
 787     CFG_CHIBI_CHANNEL           802.15.4 Channel (0 = 868MHz, 1-10 = 915MHz)
 788     CFG_CHIBI_PANID             16-bit PAN Identifier (ex.0x1234)
 789     CFG_CHIBI_PROMISCUOUS       Set to 1 to enabled promiscuous mode or
 790                                 0 to disable it.  If promiscuous mode is
 791                                 enabled be sure to set CFG_CHIBI_BUFFERSIZE
 792                                 to an appropriately large value (ex. 1024)
 793     CFG_CHIBI_BUFFERSIZE        The size of the message buffer in bytes
 794
 795     DEPENDENCIES:               Chibi requires the use of SSP0, 16-bit timer
 796                                 0 and pins 3.1, 3.2, 3.3.  It also requires
 797                                 the presence of CFG_I2CEEPROM.
 798
 799     NOTE:                       These settings are not relevant to all boards!
 800                                 'tools/schematics/AT86RF212LPC1114_v1.6.pdf'
 801                                 show how 'CHIBI' is meant to be connected
 802     -----------------------------------------------------------------------*/
 803     #ifdef CFG_BRD_LPC1343_REFDESIGN
 804       // #define CFG_CHIBI
 805       #define CFG_CHIBI_MODE              (0)                 // OQPSK_868MHZ
 806       #define CFG_CHIBI_POWER             (0xE9)              // CHB_PWR_EU2_3DBM
 807       #define CFG_CHIBI_CHANNEL           (0)                 // 868-868.6 MHz
 808       #define CFG_CHIBI_PANID             (0x1234)
 809       #define CFG_CHIBI_PROMISCUOUS       (0)
 810       #define CFG_CHIBI_BUFFERSIZE        (128)
 811     #endif
 812
 813     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 814       // #define CFG_CHIBI
 815       #define CFG_CHIBI_MODE              (0)                 // OQPSK_868MHZ
 816       #define CFG_CHIBI_POWER             (0xE9)              // CHB_PWR_EU2_3DBM
 817       #define CFG_CHIBI_CHANNEL           (0)                 // 868-868.6 MHz
 818       #define CFG_CHIBI_PANID             (0x1234)
 819       #define CFG_CHIBI_PROMISCUOUS       (0)
 820       #define CFG_CHIBI_BUFFERSIZE        (128)
 821     #endif
 822
 823     #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 824       // #define CFG_CHIBI
 825       #define CFG_CHIBI_MODE              (0)                 // OQPSK_868MHZ
 826       #define CFG_CHIBI_POWER             (0xE9)              // CHB_PWR_EU2_3DBM
 827       #define CFG_CHIBI_CHANNEL           (0)                 // 868-868.6 MHz
 828       #define CFG_CHIBI_PANID             (0x1234)
 829       #define CFG_CHIBI_PROMISCUOUS       (0)
 830       #define CFG_CHIBI_BUFFERSIZE        (128)
 831     #endif
 832
 833     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 834       #define CFG_CHIBI
 835       #define CFG_CHIBI_MODE              (0)                 // OQPSK_868MHZ
 836       #define CFG_CHIBI_POWER             (0xE9)              // CHB_PWR_EU2_3DBM
 837       #define CFG_CHIBI_CHANNEL           (0)                 // 868-868.6 MHz
 838       #define CFG_CHIBI_PANID             (0x1234)
 839       #define CFG_CHIBI_PROMISCUOUS       (0)
 840       #define CFG_CHIBI_BUFFERSIZE        (1024)
 841     #endif
 842 /*=========================================================================*/
 843
 844
 845 /*=========================================================================
 846     TFT LCD
 847     -----------------------------------------------------------------------
 848
 849     CFG_TFTLCD                  If defined, this will cause drivers for
 850                                 a pre-determined LCD screen to be included
 851                                 during build.  Only one LCD driver can be
 852                                 included during the build process (for ex.
 853                                 'drivers/lcd/hw/ILI9325.c')
 854     CFG_TFTLCD_INCLUDESMALLFONTS If set to 1, smallfont support will be
 855                                 included for 3x6, 5x8, 7x8 and 8x8 fonts.
 856                                 This should only be enabled if these small
 857                                 fonts are required since there is already
 858                                 support for larger fonts generated with
 859                                 Dot Factory
 860                                 http://www.pavius.net/downloads/tools/53-the-dot-factory
 861     CFG_TFTLCD_TS_DEFAULTTHRESHOLD  Default minimum threshold to trigger a
 862                                 touch event with the touch screen (and exit
 863                                 from 'tsWaitForEvent' in touchscreen.c).
 864                                 Should be an 8-bit value somewhere between
 865                                 8 and 75 in normal circumstances.  This is
 866                                 the default value and may be overriden by
 867                                 a value stored in EEPROM.
 868     CFG_TFTLCD_TS_KEYPADDELAY   The delay in milliseconds between key
 869                                 presses in dialogue boxes
 870
 871     PIN LAYOUT:                 The pin layout that is used by this driver
 872                                 can be seen in the following schematic:
 873                                 /tools/schematics/Breakout_TFTLCD_ILI9325_v1.3
 874
 875     DEPENDENCIES:               TFTLCD requires the use of pins 1.8, 1.9,
 876                                 1.10, 1.11, 3.3 and 2.1-9.
 877     -----------------------------------------------------------------------*/
 878     #ifdef CFG_BRD_LPC1343_REFDESIGN
 879       // #define CFG_TFTLCD
 880       #define CFG_TFTLCD_INCLUDESMALLFONTS   (0)
 881       #define CFG_TFTLCD_TS_DEFAULTTHRESHOLD (50)
 882       #define CFG_TFTLCD_TS_KEYPADDELAY      (100)
 883     #endif
 884
 885     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 886       // #define CFG_TFTLCD
 887       #define CFG_TFTLCD_INCLUDESMALLFONTS   (0)
 888       #define CFG_TFTLCD_TS_DEFAULTTHRESHOLD (50)
 889       #define CFG_TFTLCD_TS_KEYPADDELAY      (100)
 890     #endif
 891
 892     #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 893       #define CFG_TFTLCD
 894       #define CFG_TFTLCD_INCLUDESMALLFONTS   (0)
 895       #define CFG_TFTLCD_TS_DEFAULTTHRESHOLD (50)
 896       #define CFG_TFTLCD_TS_KEYPADDELAY      (100)
 897     #endif
 898
 899     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 900       // #define CFG_TFTLCD
 901       #define CFG_TFTLCD_INCLUDESMALLFONTS   (0)
 902       #define CFG_TFTLCD_TS_DEFAULTTHRESHOLD (50)
 903       #define CFG_TFTLCD_TS_KEYPADDELAY      (100)
 904     #endif
 905 /*=========================================================================*/
 906
 907
 908 /*=========================================================================
 909     Monochrome/Bitmap Graphic LCDs
 910     -----------------------------------------------------------------------
 911
 912     CFG_ST7565                If defined, this will cause drivers for
 913                               the 128x64 pixel ST7565 LCD to be included
 914     CFG_SSD1306               If defined, this will cause drivers for
 915                               the 128x64 pixel SSD1306 OLED display to be
 916                               included
 917     CFG_SHARPMEM              If defined, this will cause drivers for
 918                               Sharp Memory Displays to be included
 919
 920     DEPENDENCIES:             ST7565 requires the use of pins 2.1-6.
 921     DEPENDENCIES:             SSD1306 requires the use of pins 2.1-6.
 922     DEPENDENCIES:             SHARPMEM requires the use of pins 2.1-4.
 923     -----------------------------------------------------------------------*/
 924     // #define CFG_ST7565
 925     // #define CFG_SSD1306
 926     // #define CFG_SHARPMEM
 927 /*=========================================================================*/
 928
 929
 930 /*=========================================================================
 931     RSA Encryption
 932     -----------------------------------------------------------------------
 933
 934     CFG_RSA                     If defined, support for basic RSA
 935                                 encryption will be included.
 936     CFG_RSA_BITS                Indicates the number of bits used for
 937                                 RSA encryption keys.  To keep code size
 938                                 reasonable, RSA encryption is currently
 939                                 limited to using 64-bit or 32-bit numbers,
 940                                 with 64-bit providing higher security, and
 941                                 32-bit providing smaller encrypted text
 942                                 size.
 943
 944     NOTE:                       Please note that Printf can not be
 945                                 used to display 64-bit values (%lld)!
 946     -----------------------------------------------------------------------*/
 947     // #define CFG_RSA
 948     #define CFG_RSA_BITS                  (32)
 949 /*=========================================================================*/
 950
 951
 952
 953
 954 /*=========================================================================
 955   CONFIG FILE VALIDATION
 956   -------------------------------------------------------------------------
 957   Basic error checking to make sure that incompatible defines are not
 958   enabled at the same time, etc.
 959
 960   =========================================================================*/
 961
 962 #if !defined CFG_BRD_LPC1343_REFDESIGN && !defined CFG_BRD_LPC1343_REFDESIGN_MINIMAL && !defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB && !defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART && !defined CFG_BRD_LPC1343_802154USBSTICK
 963   #error "You must defined a target board (CFG_BRD_LPC1343_REFDESIGN or CFG_BRD_LPC1343_REFDESIGN_MINIMAL or CFG_BRD_LPC1343_TFTLCDSTANDALONE or CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART or CFG_BRD_LPC1343_802154USBSTICK)"
 964 #endif
 965
 966 #if defined CFG_PRINTF_USBCDC && defined CFG_PRINTF_UART
 967   #error "CFG_PRINTF_UART or CFG_PRINTF_USBCDC cannot both be defined at once"
 968 #endif
 969
 970 #if defined CFG_PRINTF_USBCDC && !defined CFG_USBCDC
 971   #error "CFG_PRINTF_CDC requires CFG_USBCDC to be defined as well"
 972 #endif
 973
 974 #if defined CFG_USBCDC && defined CFG_USBHID
 975   #error "Only one USB class can be defined at a time (CFG_USBCDC or CFG_USBHID)"
 976 #endif
 977
 978 #if defined CFG_SSP0_SCKPIN_2_11 && defined CFG_SSP0_SCKPIN_0_6
 979   #error "Only one SCK pin can be defined at a time for SSP0"
 980 #endif
 981
 982 #if !defined CFG_SSP0_SCKPIN_2_11 && !defined CFG_SSP0_SCKPIN_0_6
 983   #error "An SCK pin must be selected for SSP0 (CFG_SSP0_SCKPIN_2_11 or CFG_SSP0_SCKPIN_0_6)"
 984 #endif
 985
 986 #ifdef CFG_INTERFACE
 987   #if !defined CFG_PRINTF_UART && !defined CFG_PRINTF_USBCDC
 988     #error "CFG_PRINTF_UART or CFG_PRINTF_USBCDC must be defined for for CFG_INTERFACE Input/Output"
 989   #endif
 990   #if defined CFG_PRINTF_USBCDC && CFG_INTERFACE_SILENTMODE == 1
 991     #error "CFG_INTERFACE_SILENTMODE typically isn't enabled with CFG_PRINTF_USBCDC"
 992   #endif
 993 #endif
 994
 995 #ifdef CFG_CHIBI
 996   #if !defined CFG_I2CEEPROM
 997     #error "CFG_CHIBI requires CFG_I2CEEPROM to store and retrieve addresses"
 998   #endif
 999   #ifdef CFG_SDCARD
1000     #error "CFG_CHIBI and CFG_SDCARD can not be defined at the same time. Only one SPI block is available on the LPC1343."
1001   #endif
1002   #ifdef CFG_TFTLCD
1003     #error "CFG_CHIBI and CFG_TFTLCD can not be defined at the same time since they both use pins 1.8, 1.9 and 1.10."
1004   #endif
1005   #ifdef CFG_PWM
1006     #error "CFG_CHIBI and CFG_PWM can not be defined at the same time since they both use pin 1.9."
1007   #endif
1008   #if CFG_CHIBI_PROMISCUOUS != 0 && CFG_CHIBI_PROMISCUOUS != 1
1009     #error "CFG_CHIBI_PROMISCUOUS must be equal to either 1 or 0"
1010   #endif
1011 #endif
1012
1013 #ifdef CFG_TFTLCD
1014   #ifdef CFG_ST7565
1015     #error "CFG_TFTLCD and CFG_ST7565 can not be defined at the same time."
1016   #endif
1017   #ifdef CFG_SSD1306
1018     #error "CFG_TFTLCD and CFG_SSD1306 can not be defined at the same time."
1019   #endif
1020   #ifdef CFG_PWM
1021     #error "CFG_TFTLCD and CFG_PWM can not be defined at the same time since they both use pin 1.9."
1022   #endif
1023   #if !defined CFG_I2CEEPROM
1024     #error "CFG_TFTLCD requires CFG_I2CEEPROM to store and retrieve configuration settings"
1025   #endif
1026 #endif
1027
1028 #ifdef CFG_SDCARD
1029   #ifdef CFG_STEPPER
1030     #error  "CFG_SDCARD and CFG_STEPPER can not be defined at the same time since they both use pin 3.0."
1031   #endif
1032 #endif
1033
1034 #ifdef CFG_ST7565
1035   #ifdef CFG_SSD1306
1036     #error "CFG_ST7565 and CFG_SSD1306 can not be defined at the same time"
1037   #endif
1038 #endif
1039
1040 #ifdef CFG_RSA
1041   #if CFG_RSA_BITS != 64 && CFG_RSA_BITS != 32
1042     #error "CFG_RSA_BITS must be equal to either 32 or 64."
1043   #endif
1044 #endif
1045
1046 #endif