target/linux/brcm47xx/patches-2.6.35/021-USB-Add-USB-2.0-to-ssb-ohci-driver.patch

   1 From cb33ffbdd8491c58b35958ec74c39b3a5c7fabe8 Mon Sep 17 00:00:00 2001
   2 From: Hauke Mehrtens <hauke@hauke-m.de>
   3 Date: Sun, 18 Jul 2010 21:25:03 +0200
   4 Subject: [PATCH 1/2] USB: Add USB 2.0 to ssb ohci driver
   5
   6 This adds USB 2.0 support to ssb ohci driver.
   7 This work was done based on Braodcom source code in the OpenWRT project.
   8
   9 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
  10 ---
  11  drivers/usb/host/ohci-ssb.c |   55 ++++++++++++++++++++++++++++++++++++++++--
  12  1 files changed, 52 insertions(+), 3 deletions(-)
  13
  14 --- a/drivers/usb/host/ohci-ssb.c
  15 +++ b/drivers/usb/host/ohci-ssb.c
  16 @@ -92,9 +92,12 @@ static const struct hc_driver ssb_ohci_h
  17  static void ssb_ohci_detach(struct ssb_device *dev)
  18  {
  19         struct usb_hcd *hcd = ssb_get_drvdata(dev);
  20 +       if (hcd->driver->shutdown)
  21 +               hcd->driver->shutdown(hcd);
  22
  23         usb_remove_hcd(hcd);
  24         iounmap(hcd->regs);
  25 +       release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
  26         usb_put_hcd(hcd);
  27         ssb_device_disable(dev, 0);
  28  }
  29 @@ -106,10 +109,55 @@ static int ssb_ohci_attach(struct ssb_de
  30         int err = -ENOMEM;
  31         u32 tmp, flags = 0;
  32
  33 -       if (dev->id.coreid == SSB_DEV_USB11_HOSTDEV)
  34 -               flags |= SSB_OHCI_TMSLOW_HOSTMODE;
  35 +       if (dma_set_mask(dev->dma_dev, DMA_BIT_MASK(32)) ||
  36 +           dma_set_coherent_mask(dev->dma_dev, DMA_BIT_MASK(32)))
  37 +               return -EOPNOTSUPP;
  38
  39 -       ssb_device_enable(dev, flags);
  40 +       if (dev->id.coreid == SSB_DEV_USB11_HOSTDEV) {
  41 +               /* Put the device into host-mode. */
  42 +               flags |= SSB_OHCI_TMSLOW_HOSTMODE;
  43 +               ssb_device_enable(dev, flags);
  44 +       } else if (dev->id.coreid == SSB_DEV_USB20_HOST) {
  45 +               /*
  46 +                * USB 2.0 special considerations:
  47 +                *
  48 +                * 1. Since the core supports both ehci and EHCI functions, it must
  49 +                *    only be reset once.
  50 +                *
  51 +                * 2. In addition to the standard SSB reset sequence, the Host Control
  52 +                *    Register must be programmed to bring the USB core and various
  53 +                *    phy components out of reset.
  54 +                */
  55 +               ssb_device_enable(dev, 0);
  56 +               ssb_write32(dev, 0x200, 0x7ff);
  57 +
  58 +               /* Change Flush control reg */
  59 +               tmp = ssb_read32(dev, 0x400);
  60 +               tmp &= ~8;
  61 +               ssb_write32(dev, 0x400, tmp);
  62 +               tmp = ssb_read32(dev, 0x400);
  63 +
  64 +               /* Change Shim control reg */
  65 +               tmp = ssb_read32(dev, 0x304);
  66 +               tmp &= ~0x100;
  67 +               ssb_write32(dev, 0x304, tmp);
  68 +               tmp = ssb_read32(dev, 0x304);
  69 +
  70 +               udelay(1);
  71 +
  72 +               /* Work around for 5354 failures */
  73 +               if ((dev->id.revision == 2) && (dev->bus->chip_id == 0x5354)) {
  74 +                       /* Change syn01 reg */
  75 +                       tmp = 0x00fe00fe;
  76 +                       ssb_write32(dev, 0x894, tmp);
  77 +
  78 +                       /* Change syn03 reg */
  79 +                       tmp = ssb_read32(dev, 0x89c);
  80 +                       tmp |= 0x1;
  81 +                       ssb_write32(dev, 0x89c, tmp);
  82 +               }
  83 +       } else
  84 +               ssb_device_enable(dev, 0);
  85
  86         hcd = usb_create_hcd(&ssb_ohci_hc_driver, dev->dev,
  87                         dev_name(dev->dev));
  88 @@ -200,6 +248,7 @@ static int ssb_ohci_resume(struct ssb_de
  89  static const struct ssb_device_id ssb_ohci_table[] = {
  90         SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_USB11_HOSTDEV, SSB_ANY_REV),
  91         SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_USB11_HOST, SSB_ANY_REV),
  92 +       SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_USB20_HOST, SSB_ANY_REV),
  93         SSB_DEVTABLE_END
  94  };
  95  MODULE_DEVICE_TABLE(ssb, ssb_ohci_table);