final tweaks

[bachelor-thesis/written-stuff.git] / Ausarbeitung / experiment1.tex

diff --git a/Ausarbeitung/experiment1.tex b/Ausarbeitung/experiment1.tex
index bea1dc6..abc2a7e 100644 (file)
--- a/Ausarbeitung/experiment1.tex
+++ b/Ausarbeitung/experiment1.tex
@@ -1,57 +1,152 @@
-\chapter{Experiment 1: Original Movement Behaviour}
-\todo
+\chapter{Experiment 1: Original Movement Behavior}
+\label{sec:exp1}
+
+The concepts described in the previous chapter are now used to set up a test
+series with the purpose to measure the error in the Roomba's movement and
+to improve its accuracy.
+
+In the first experiment, the Roomba's original movement behavior was
+measured to get an overview of the errors that occur while moving, and to
+establish a pool of data for correction approaches to work on later.
+There was no error correction involved (apart from any possible error
+correction the Roomba itself implements in its underlying logic, and which is
+not known to anyone except iRobot). To achieve this, the Wiselib Roomba Control
+is used to access the Roomba over the \ac{ROI}\index{Roomba Open Interface}.
+

 \section{Setup}
 \section{Setup}

+The test equipment consisted of a small x86 netbook\index{netbook} which was
+mounted on an iRobot Roomba~530\index{Roomba} robot, as seen in
+Figure~\ref{fig:roombasetup}. The netbook controlled the Roomba over a
+\acs{USB}-to-serial converter plugged into the \ac{ROI}\index{Roomba
+Open Interface} port on the Roomba, and hosted as the environment for
+executing the Wiselib \index{Wiselib} code.

 
 

-\begin{figure}[htp]
+\label{sec:exp1:setup}
+\begin{figure}

  \centering
  \includegraphics[width=0.45\textwidth]{./images/IMAGE_00079.jpg}
  \centering
  \includegraphics[width=0.45\textwidth]{./images/IMAGE_00079.jpg}

- \caption{Roomba with netbook}
+ \caption{Roomba with netbook\label{fig:roombasetup}}

 \end{figure}
 \end{figure}

-\begin{figure}[htp]
+\begin{figure}

  \centering
  \includegraphics[width=0.6\textwidth]{./images/IMAGE_00148.jpg}
  \centering
  \includegraphics[width=0.6\textwidth]{./images/IMAGE_00148.jpg}

- \caption{Measuring turn angles with laser pointer}
+ \caption{Measuring turn angles with laser pointer\label{fig:laserpointer}}

 \end{figure}
 
 \end{figure}
 

-Description of experiment setup: netbook on Roomba, application
-"`roomba\_tests"' started which took care of the input values, user was asked
-to measure \& input the data. there were Turn tests and straight drive tests,
-different floor types: laminate and carpet floor.
+In this experiment, the Roomba started and stopped with the full velocity the
+movement was executed with; so there was (ideally speaking) an infinite
+acceleration and deceleration at the start and the end of the movement. As
+mentioned before, due to limitations in the \ac{ROI}\index{Roomba Open
+Interface} it is only possible to explicitly start and stop the Roomba's
+movements at different times, so the Wiselib's implementation of the Roomba
+control code first starts the Roomba's movement, keeps track of the turned angle
+and covered distance, and then stops the Roomba if these values exceed the
+target values.
+
+The tests were done in two atomic drive modes: letting the Roomba walk a
+specific straight distance with a specific velocity in its viewing direction and
+letting it turn on the spot with a specific velocity about a specific angle.
+Each of the two modes was carried out on two different floor types\index{floor
+type}, a laminated floor and a carpet floor, to see if the movement behavior
+significantly depended on the floor type. The side brush was removed, since the
+Roomba tends to turn slightly towards the left when driving straight on a
+carpet floor. Without the side brush, this was not the case.
+
+The actual traveled distance of the straight drive tests were determined using
+a measuring tape with an accuracy of 1~mm. Only the distance in the Roomba's
+original viewing direction was considered, as it turned out that the offset
+perpendicular to the viewing direction and a possible shift in orientation were
+too small to be measured precisely.
+
+The actual turn angles of the turn tests were determined using a
+\acs{ISO}/\acs{DIN}~A0 sheet of paper with a printed polar coordinate system in
+which a circular hole was cut in the center to let the Roomba's wheels touch the
+floor. The sheet was fixed on the floor, and the Roomba was aligned in the
+center of the paper. A laser pointer\index{laser pointer} attached to the Roomba
+pointed to the current orientation on the paper, as shown in
+Fig.~\ref{fig:laserpointer}. The accuracy for these tests was 1~degree.

 
 

-drive tests: measuring was done with measuring tape. error perpendicular to
-roomba's viewing direction was too small to be measured.
+After the initial setup, the application \prog{roomba\_test} (see
+section~\ref{sec:impl:measuring}) was started on the netbook for half-automatic
+testing. It used a predefined array of nominal distances, angles and velocities
+and for each pair of distance (for straight drive tests) or angle (for turn
+tests) and velocity it used the Wiselib implementation to move the Roomba. Then
+it asked the user to input the measured distance or angle the Roomba had moved
+and repeated the process until each combination of distance/angle and velocity
+was used. The nominal and input values were written to a log file, as well as
+the floor type, the Roomba ID, the \ac{SVN} revision the program was built
+from, the battery status\index{battery status}, and other internal
+implementation-specific values.

 
 

-velocities =  20, 50, 70, 100, 150, 200, 300, 400 mm/s \\
-distances =  20, 50, 100, 200, 500, 1000, 2000, 4000 mm
+For the straight drive tests, the arrays with predefined values were:\\
+\begin{tabular}{@{}ll@{}}
+Distances: & 20, 50, 100, 200, 500, 1000, 2000 and 4000~mm \\
+Velocities: & 20, 50, 70, 100, 150, 200, 300 and 400~mm/s
+\end{tabular}

 
 

-turn tests: measuring with polar coordinate system of about 1~m diameter, roomba
-in the center, laser pointer points to measured value.
+For the turn tests, the arrays with predefined values were: \\
+\begin{tabular}{@{}ll@{}}
+Turn angles: & \phantom{0}5, 15, 30, 45, 90, 120, 180, 360, 530 and 720~degree\\
+Velocities: & 20, 50, 70, 100, 150, 200, 300 and 400~mm/s
+\end{tabular}

 
 

-velocities =  20, 50, 70, 100, 150, 200, 300, 400  mm/s\\
-turn angles =  5, 15, 30, 45, 90, 120, 180, 360, 530, 720 degree
+According to the implementation of the Wiselib Roomba control, the velocities
+were given in mm/s and referred to the distance the wheels traveled when the
+Roomba turned on the spot, which was a circle of 230~mm in diameter.

 
 \section{Results}
 
 \section{Results}

-\begin{figure}
+\label{exp1:results}
+The following graphs show the difference from the measured value to the input
+value for driving or turning with different velocities. Positive values mean
+that the Roomba had turned too much or traveled more than the target value,
+negative values mean that the Roomba had turned or traveled less. The
+plots show multiple test runs; given are the minimum, the maximum and the
+arithmetic mean\index{arithmetic mean} of all results for a data point.
+
+\begin{figure}[p!]

  \centering
  \includegraphics[width=\textwidth]{images/iz250flur_drive_data.pdf}
  \centering
  \includegraphics[width=\textwidth]{images/iz250flur_drive_data.pdf}

- \caption{foo}
+ \caption{Original behavior on laminated floor, straight drive movements
+  \label{fig:orig:lam:drive}}

 \end{figure}
 \end{figure}

-\begin{figure}
+\begin{figure}[p!]

  \centering
  \includegraphics[width=\textwidth]{images/iz250flur_turn_data.pdf}
  \centering
  \includegraphics[width=\textwidth]{images/iz250flur_turn_data.pdf}

- \caption{foo}
+ \caption{Original behavior on laminated floor, turn movements
+  \label{fig:orig:lam:turn}}

 \end{figure}
 \end{figure}

-\begin{figure}
+\begin{figure}[p!]

  \centering
  \includegraphics[width=\textwidth]{images/seminarraum_drive_data.pdf}
  \centering
  \includegraphics[width=\textwidth]{images/seminarraum_drive_data.pdf}

- \caption{foo}
+ \caption{Original behavior on carpet floor, straight drive movements
+  \label{fig:orig:carpet:drive}}

 \end{figure}
 \end{figure}

-\begin{figure}
+\begin{figure}[p!]

  \centering
  \includegraphics[width=\textwidth]{images/seminarraum_turn_data.pdf}
  \centering
  \includegraphics[width=\textwidth]{images/seminarraum_turn_data.pdf}

- \caption{foo}
+ \caption{Original behavior on carpet floor, turn movements
+  \label{fig:orig:carpet:turn}}

 \end{figure}
 
 \end{figure}
 

-Absolute error becomes greater with increasing velocity and input value, but
-error is smaller on carpet floor.
-\todo{statistical values, stddev?}
+Figure~\ref{fig:orig:lam:drive} shows that the error becomes greater with
+increasing input distance when driving straight on the laminated floor, however,
+in Figure~\ref{fig:orig:carpet:drive} we see the opposite effect on the carpet
+floor, the error decreases with greater input distance. This could happen due to
+imprecise measurement of distances in either the Roomba's sensors or the Wiselib
+implementation that controls the Roomba, or both, adding up over the time the
+movement continues. Also slippage of the wheels on the laminated floor could be
+possible, as well as slowdown through the carpet floor, explaining why the error
+increases on the laminated floor, but decreases into negative values on the
+carpet floor when the distance grows.
+
+On the other hand, rising the velocity always seems to cause the
+error to increase. This illustrates the effect of accumulating errors which
+represents the crucial drawback of dead reckoning\index{dead reckoning}.
+
+The same effects also apply for turn tests. Additionally, there could be errors
+resulting from false assumptions about the Roomba's wheel base\index{wheel
+base}, resulting in bogus calculations of the circle the Roomba's wheels
+describe while turning, and therefore leading to false results.
+
+In the following, two approaches to correct errors and improve the accuracy of
+the movement are presented.