are using by enabling one of the following definitions. The code base
will then try to configure itself accordingly for that board.
-----------------------------------------------------------------------*/
- // #define CFG_BRD_LPC1343_REFDESIGN
- #define CFG_BRD_LPC1343_TFTLCDSTANDALONE
+ #define CFG_BRD_LPC1343_REFDESIGN
+ // #define CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
+ // #define CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
// #define CFG_BRD_LPC1343_802154USBSTICK
/*=========================================================================*/
**************************************************************************/
+/**************************************************************************
+ I2C Addresses
+ -----------------------------------------------------------------------
+ The following addresses are used by the different I2C sensors included
+ in the code base [1]
+
+ HEX BINARY
+ ==== ========
+ ISL12022M (RTC) 0xDE 1101111x
+ ISL12022M (SRAM) 0xAE 1010111x
+ LM75B 0x90 1001000x
+ MCP24AA 0xA0 1010000x
+ MCP4725 0xC0 1100000x
+ TSL2561 0x72 0111001x
+ TCS3414 0x72 0111001x
+
+ [1] Alternative addresses may exists, but the addresses listed in this
+ table are the values used in the code base
+
+ **************************************************************************/
+
+
/*=========================================================================
FIRMWARE VERSION SETTINGS
-----------------------------------------------------------------------*/
#define CFG_FIRMWARE_VERSION_MAJOR (0)
#define CFG_FIRMWARE_VERSION_MINOR (9)
- #define CFG_FIRMWARE_VERSION_REVISION (2)
+ #define CFG_FIRMWARE_VERSION_REVISION (3)
/*=========================================================================*/
other peripherals to determine timing.
-----------------------------------------------------------------------*/
- #ifdef CFG_BRD_LPC1343_REFDESIGN
- #define CFG_CPU_CCLK (72000000) // 1 tick = 13.88nS
- #endif
-
- #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE
- #define CFG_CPU_CCLK (72000000) // 1 tick = 13.88nS
- #endif
-
- #ifdef CFG_BRD_LPC1343_802154USBSTICK
- #define CFG_CPU_CCLK (72000000) // 1 tick = 13.88nS
- #endif
+ #define CFG_CPU_CCLK (72000000) // 1 tick = 13.88nS
/*=========================================================================*/
of the systick timer.
-----------------------------------------------------------------------*/
- #ifdef CFG_BRD_LPC1343_REFDESIGN
- #define CFG_SYSTICK_DELAY_IN_MS (1)
- #endif
+ #define CFG_SYSTICK_DELAY_IN_MS (1)
+/*=========================================================================*/
- #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE
- #define CFG_SYSTICK_DELAY_IN_MS (1)
- #endif
- #ifdef CFG_BRD_LPC1343_802154USBSTICK
- #define CFG_SYSTICK_DELAY_IN_MS (1)
+/*=========================================================================
+ ALTERNATE RESET PIN
+ -----------------------------------------------------------------------
+
+ CFG_ALTRESET If defined, indicates that a GPIO pin should be
+ configured as an alternate reset pin in addition
+ to the dedicated reset pin.
+ CFG_ALTRESET_PORT The GPIO port where the alt reset pin is located
+ CFG_ALTRESET_PIN The GPIO pin where the alt reset pin is located
+
+ -----------------------------------------------------------------------*/
+ #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
+ #define CFG_ALTRESET
+ #define CFG_ALTRESET_PORT (1)
+ #define CFG_ALTRESET_PIN (5) // P1.5 = RTS
#endif
/*=========================================================================*/
#define CFG_UART_BUFSIZE (512)
#endif
- #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE
+ #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
#define CFG_UART_BAUDRATE (115200)
#define CFG_UART_BUFSIZE (512)
#endif
+ #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
+ #define CFG_UART_BAUDRATE (57600)
+ #define CFG_UART_BUFSIZE (512)
+ #endif
+
#ifdef CFG_BRD_LPC1343_802154USBSTICK
#define CFG_UART_BAUDRATE (115200)
#define CFG_UART_BUFSIZE (512)
// #define CFG_SSP0_SCKPIN_0_6
#endif
- #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE
+ #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
#define CFG_SSP0_SCKPIN_2_11
// #define CFG_SSP0_SCKPIN_0_6
#endif
#define CFG_LED_OFF (1)
#endif
- #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE
+ #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
#define CFG_LED_PORT (2)
#define CFG_LED_PIN (10)
#define CFG_LED_ON (0)
#define CFG_SDCARD_CDPIN (0)
#endif
- #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE
+ #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
#define CFG_SDCARD
#define CFG_SDCARD_READONLY (1) // Must be 0 or 1
#define CFG_SDCARD_CDPORT (3)
#define CFG_USBCDC_BUFFERSIZE (256)
#endif
- #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE
+ #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
// #define CFG_USBHID
#define CFG_USBCDC
#define CFG_USBCDC_BAUDRATE (115200)
#define CFG_USBCDC_BUFFERSIZE (256)
#endif
+ #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
+ // #define CFG_USBHID
+ // #define CFG_USBCDC
+ #define CFG_USBCDC_BAUDRATE (57600)
+ #define CFG_USBCDC_INITTIMEOUT (5000)
+ #define CFG_USBCDC_BUFFERSIZE (256)
+ #endif
+
#ifdef CFG_BRD_LPC1343_802154USBSTICK
// #define CFG_USBHID
#define CFG_USBCDC
redirected to UART
CFG_PRINTF_USBCDC Will cause all printf statements to be
redirect to USB Serial
- CFG_PRINTF_NEWLINE This should be either "\r\n" for Windows or
+ CFG_PRINTF_NEWLINE This is typically "\r\n" for Windows or
"\n" for *nix
Note: If no printf redirection definitions are present, all printf
#define CFG_PRINTF_NEWLINE "\r\n"
#endif
- #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE
+ #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
// #define CFG_PRINTF_UART
#define CFG_PRINTF_USBCDC
#define CFG_PRINTF_NEWLINE "\r\n"
#endif
+ #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
+ #define CFG_PRINTF_UART
+ // #define CFG_PRINTF_USBCDC
+ #define CFG_PRINTF_NEWLINE "\n"
+ #endif
+
#ifdef CFG_BRD_LPC1343_802154USBSTICK
// #define CFG_PRINTF_UART
#define CFG_PRINTF_USBCDC
is normally only desirable in a situation
where another MCU is communicating with
the LPC1343.
+ CFG_INTERFACE_DROPCR If this is set to 1 all incoming \r
+ characters will be dropped
CFG_INTERFACE_ENABLEIRQ If this is set to 1 the IRQ pin will be
set high when a command starts executing
and will go low when the command has
new command can safely be sent.
CFG_INTERFACE_IRQPORT The gpio port for the IRQ/busy pin
CFG_INTERFACE_IRQPIN The gpio pin number for the IRQ/busy pin
+ CFG_INTERFACE_SHORTERRORS If this is enabled only short 1 character
+ error messages will be returned (followed
+ by CFG_PRINTF_NEWLINE), rather than more
+ verbose error messages. The specific
+ characters used are defined below.
+ CFG_INTERFACE_CONFIRMREADY If this is set to 1 a text confirmation
+ will be sent when the command prompt is
+ ready for a new command. This is in
+ addition to CFG_INTERFACE_ENABLEIRQ if
+ this is also enabled. The character used
+ is defined below.
NOTE: The command-line interface will use either
USB-CDC or UART depending on whether
#define CFG_INTERFACE_MAXMSGSIZE (256)
#define CFG_INTERFACE_PROMPT "LPC1343 >> "
#define CFG_INTERFACE_SILENTMODE (0)
+ #define CFG_INTERFACE_DROPCR (0)
#define CFG_INTERFACE_ENABLEIRQ (0)
- #define CFG_INTERFACE_IRQPORT (2)
- #define CFG_INTERFACE_IRQPIN (0)
+ #define CFG_INTERFACE_IRQPORT (0)
+ #define CFG_INTERFACE_IRQPIN (7)
+ #define CFG_INTERFACE_SHORTERRORS (0)
+ #define CFG_INTERFACE_CONFIRMREADY (0)
#endif
- #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE
+ #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
#define CFG_INTERFACE
#define CFG_INTERFACE_MAXMSGSIZE (256)
- #define CFG_INTERFACE_PROMPT "LCD >> "
+ #define CFG_INTERFACE_PROMPT "CMD >> "
#define CFG_INTERFACE_SILENTMODE (0)
+ #define CFG_INTERFACE_DROPCR (0)
+ #define CFG_INTERFACE_ENABLEIRQ (0)
+ #define CFG_INTERFACE_IRQPORT (0)
+ #define CFG_INTERFACE_IRQPIN (7)
+ #define CFG_INTERFACE_SHORTERRORS (0)
+ #define CFG_INTERFACE_CONFIRMREADY (0)
+ #define CFG_INTERFACE_SHORTERRORS_UNKNOWNCOMMAND "?"
+ #define CFG_INTERFACE_SHORTERRORS_TOOMANYARGS ">"
+ #define CFG_INTERFACE_SHORTERRORS_TOOFEWARGS "<"
+ #define CFG_INTERFACE_CONFIRMREADY_TEXT "."
+ #endif
+
+ #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
+ #define CFG_INTERFACE
+ #define CFG_INTERFACE_MAXMSGSIZE (256)
+ #define CFG_INTERFACE_PROMPT ">>"
+ #define CFG_INTERFACE_SILENTMODE (1)
+ #define CFG_INTERFACE_DROPCR (1)
#define CFG_INTERFACE_ENABLEIRQ (1)
- #define CFG_INTERFACE_IRQPORT (2)
- #define CFG_INTERFACE_IRQPIN (0)
+ #define CFG_INTERFACE_IRQPORT (0)
+ #define CFG_INTERFACE_IRQPIN (7)
+ #define CFG_INTERFACE_SHORTERRORS (1)
+ #define CFG_INTERFACE_CONFIRMREADY (0)
+ #define CFG_INTERFACE_SHORTERRORS_UNKNOWNCOMMAND "?"
+ #define CFG_INTERFACE_SHORTERRORS_TOOMANYARGS ">"
+ #define CFG_INTERFACE_SHORTERRORS_TOOFEWARGS "<"
+ #define CFG_INTERFACE_CONFIRMREADY_TEXT "."
#endif
#ifdef CFG_BRD_LPC1343_802154USBSTICK
#define CFG_INTERFACE_MAXMSGSIZE (256)
#define CFG_INTERFACE_PROMPT "CMD >> "
#define CFG_INTERFACE_SILENTMODE (0)
+ #define CFG_INTERFACE_DROPCR (0)
#define CFG_INTERFACE_ENABLEIRQ (0)
- #define CFG_INTERFACE_IRQPORT (2)
- #define CFG_INTERFACE_IRQPIN (0)
+ #define CFG_INTERFACE_IRQPORT (0)
+ #define CFG_INTERFACE_IRQPIN (7)
+ #define CFG_INTERFACE_SHORTERRORS (0)
+ #define CFG_INTERFACE_CONFIRMREADY (0)
#endif
/*=========================================================================*/
DEPENDENCIES: PWM output requires the use of 16-bit
timer 1 and pin 1.9 (CT16B1_MAT0).
-----------------------------------------------------------------------*/
- #ifdef CFG_BRD_LPC1343_REFDESIGN
- // #define CFG_PWM
- #define CFG_PWM_DEFAULT_PULSEWIDTH (CFG_CPU_CCLK / 1000)
- #define CFG_PWM_DEFAULT_DUTYCYCLE (50)
- #endif
-
- #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE
- // #define CFG_PWM
- #define CFG_PWM_DEFAULT_PULSEWIDTH (CFG_CPU_CCLK / 1000)
- #define CFG_PWM_DEFAULT_DUTYCYCLE (50)
- #endif
-
- #ifdef CFG_BRD_LPC1343_802154USBSTICK
- // #define CFG_PWM
- #define CFG_PWM_DEFAULT_PULSEWIDTH (CFG_CPU_CCLK / 1000)
- #define CFG_PWM_DEFAULT_DUTYCYCLE (50)
- #endif
+ // #define CFG_PWM
+ #define CFG_PWM_DEFAULT_PULSEWIDTH (CFG_CPU_CCLK / 1000)
+ #define CFG_PWM_DEFAULT_DUTYCYCLE (50)
/*=========================================================================*/
DEPENDENCIES: STEPPER requires the use of pins 3.0-3 and
32-bit Timer 0.
-----------------------------------------------------------------------*/
- #ifdef CFG_BRD_LPC1343_REFDESIGN
- // #define CFG_STEPPER
- #endif
-
- #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE
- // #define CFG_STEPPER
- #endif
-
- #ifdef CFG_BRD_LPC1343_802154USBSTICK
- // #define CFG_STEPPER
- #endif
+ // #define CFG_STEPPER
/*=========================================================================*/
#define CFG_I2CEEPROM_SIZE (3072)
#endif
- #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE
+ #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
#define CFG_I2CEEPROM
#define CFG_I2CEEPROM_SIZE (3072)
#endif
#define CFG_EEPROM_RESERVED (0x00FF) // Protect first 256 bytes of memory
#define CFG_EEPROM_CHIBI_IEEEADDR (uint16_t)(0x0000) // 8
#define CFG_EEPROM_CHIBI_SHORTADDR (uint16_t)(0x0009) // 2
+ #define CFG_EEPROM_UART_SPEED (uint16_t)(0x0020) // 4
#define CFG_EEPROM_TOUCHSCREEN_CALIBRATED (uint16_t)(0x0030) // 1
#define CFG_EEPROM_TOUCHSCREEN_CAL_AN (uint16_t)(0x0031) // 4
#define CFG_EEPROM_TOUCHSCREEN_CAL_BN (uint16_t)(0x0035) // 4
#define CFG_EEPROM_TOUCHSCREEN_CAL_FN (uint16_t)(0x0045) // 4
#define CFG_EEPROM_TOUCHSCREEN_CAL_DIVIDER (uint16_t)(0x0049) // 4
#define CFG_EEPROM_TOUCHSCREEN_THRESHHOLD (uint16_t)(0x004D) // 1
- #define CFG_EEPROM_UART_SPEED (uint16_t)(0x0020) // 4
/*=========================================================================*/
build (requires external HW)
-----------------------------------------------------------------------*/
- #ifdef CFG_BRD_LPC1343_REFDESIGN
- // #define CFG_LM75B
- #endif
-
- #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE
- // #define CFG_LM75B
- #endif
-
- #ifdef CFG_BRD_LPC1343_802154USBSTICK
- // #define CFG_LM75B
- #endif
+ // #define CFG_LM75B
/*=========================================================================*/
#define CFG_CHIBI_BUFFERSIZE (128)
#endif
- #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE
+ #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
// #define CFG_CHIBI
#define CFG_CHIBI_MODE (0) // OQPSK_868MHZ
#define CFG_CHIBI_POWER (0xE9) // CHB_PWR_EU2_3DBM
#define CFG_TFTLCD_TS_KEYPADDELAY (100)
#endif
- #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE
+ #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
#define CFG_TFTLCD
#define CFG_TFTLCD_INCLUDESMALLFONTS (0)
#define CFG_TFTLCD_TS_DEFAULTTHRESHOLD (50)
DEPENDENCIES: ST7565 requires the use of pins 2.1-6.
DEPENDENCIES: SSD1306 requires the use of pins 2.1-6.
-----------------------------------------------------------------------*/
- #ifdef CFG_BRD_LPC1343_REFDESIGN
- // #define CFG_ST7565
- // #define CFG_SSD1306
- #endif
-
- #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE
- // #define CFG_ST7565
- // #define CFG_SSD1306
- #endif
-
- #ifdef CFG_BRD_LPC1343_802154USBSTICK
- // #define CFG_ST7565
- // #define CFG_SSD1306
- #endif
+ // #define CFG_ST7565
+ // #define CFG_SSD1306
/*=========================================================================*/
NOTE: Please note that Printf can not be
used to display 64-bit values (%lld)!
-----------------------------------------------------------------------*/
- #ifdef CFG_BRD_LPC1343_REFDESIGN
- // #define CFG_RSA
- #define CFG_RSA_BITS (32)
- #endif
-
- #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE
- // #define CFG_RSA
- #define CFG_RSA_BITS (32)
- #endif
-
- #ifdef CFG_BRD_LPC1343_802154USBSTICK
- // #define CFG_RSA
- #define CFG_RSA_BITS (32)
- #endif
+ // #define CFG_RSA
+ #define CFG_RSA_BITS (32)
/*=========================================================================*/
=========================================================================*/
-#if !defined CFG_BRD_LPC1343_REFDESIGN && !defined CFG_BRD_LPC1343_TFTLCDSTANDALONE && !defined CFG_BRD_LPC1343_802154USBSTICK
- #error "You must defined a target board (CFG_BRD_LPC1343_REFDESIGN or CFG_BRD_LPC1343_TFTLCDSTANDALONE or CFG_BRD_LPC1343_802154USBSTICK)"
-#endif
-#if (defined CFG_BRD_LPC1343_REFDESIGN && defined CFG_BRD_LPC1343_TFTLCDSTANDALONE) || (defined CFG_BRD_LPC1343_TFTLCDSTANDALONE && defined CFG_BRD_LPC1343_802154USBSTICK) || (defined CFG_BRD_LPC1343_REFDESIGN && defined CFG_BRD_LPC1343_802154USBSTICK)
- #error "Only one target board can be defined at a time"
+#if !defined CFG_BRD_LPC1343_REFDESIGN && !defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB && !defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART && !defined CFG_BRD_LPC1343_802154USBSTICK
+ #error "You must defined a target board (CFG_BRD_LPC1343_REFDESIGN or CFG_BRD_LPC1343_TFTLCDSTANDALONE or CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART or CFG_BRD_LPC1343_802154USBSTICK)"
#endif
#if defined CFG_PRINTF_USBCDC && defined CFG_PRINTF_UART
projects / hackover2013-badge-firmware.git / blobdiff