Software License Agreement (BSD License)
- Copyright (c) 2010, microBuilder SARL
+ Copyright (c) 2012, microBuilder SARL
All rights reserved.
Redistribution and use in source and binary forms, with or without
microBuilder.eu USB stick 802.15.4 868/915MHz RF transceiver
+ CFG_BRD_LPC1343_OLIMEX_P
+ ==============================
+
+ Simple Olimex LPC1343 breakout board
+
+ CFG_BRD_LPC1343_LPCXPRESSO
+ ==============================
+
+ LPC1343 LPCXpresso board
+
-----------------------------------------------------------------------*/
- // #define CFG_BRD_LPC1343_REFDESIGN
+ #define CFG_BRD_LPC1343_REFDESIGN
// #define CFG_BRD_LPC1343_REFDESIGN_MINIMAL
- #define CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
+ // #define CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
// #define CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
// #define CFG_BRD_LPC1343_802154USBSTICK
// #define CFG_BRD_LPC1343_OLIMEX_P
+ // #define CFG_BRD_LPC1343_LPCXPRESSO
/*=========================================================================*/
ST7565 X X X X X X X X X X X X X . . . X
ST7735 . . . . X X X X X X . . . . . . .
SHARPMEM . . . . X X X X . . . . . . . . .
- SSD1306 . . . . X X X . X X . . . . . . .
+ SSD1306 SPI . . . . X X X . X X . . . . . . .
SSD1351 . . . . X X X X X . . . . . . . .
MCP121 . . . . . . . . . . . . . . X . .
PN532 [3] . . . . . . . . . . . . . . X X .
ST7565 . . . . . X X X X .
ST7535 . . . . . . . . . .
SHARPMEM . . . . . . . . . .
- SSD1306 . . . . . . . . . .
+ SSD1306 SPI . . . . . . . . . .
INTERFACE . . . . . . . . . X[2]
[1] PMU uses 32-bit Timer 0 for SW wakeup from deep-sleep. This timer
can safely be used by other peripherals, but may need to be
reconfigured when you wakeup from deep-sleep.
[2] INTERFACE can be configured to use either USBCDC or UART
- [3] 3.2 only used when with the I2C bus (for IRQ)
+ [3] P3.2 is only used with the I2C bus (for IRQ)
**************************************************************************/
ISL12022M (SRAM) 0xAE 1010111x
LM75B 0x90 1001000x
MCP24AA 0xA0 1010000x
- MCP4725 0xC0 1100000x
+ MCP4725 0xC0 1100000x ***
+ TEA5767 0xC0 1100000x ***
TSL2561 0x72 0111001x
TCS3414 0x72 0111001x
PN532 0x48 0100100x
+ SSD1306_I2C 0x78 0111100x // Assumes SA0 = GND
+ INA219 0xF0 10000000x // Assumes A0+A1 = GND
[1] Alternative addresses may exists, but the addresses listed in this
table are the values used in the code base
/*=========================================================================
FIRMWARE VERSION SETTINGS
-----------------------------------------------------------------------*/
- #define CFG_FIRMWARE_VERSION_MAJOR (0)
- #define CFG_FIRMWARE_VERSION_MINOR (9)
- #define CFG_FIRMWARE_VERSION_REVISION (8)
+ #define CFG_FIRMWARE_VERSION_MAJOR (1)
+ #define CFG_FIRMWARE_VERSION_MINOR (1)
+ #define CFG_FIRMWARE_VERSION_REVISION (0)
/*=========================================================================*/
// #define GPIO_ENABLE_IRQ2
// #define GPIO_ENABLE_IRQ3
#endif
+
+ #ifdef CFG_BRD_LPC1343_LPCXPRESSO
+ // #define GPIO_ENABLE_IRQ0
+ #define GPIO_ENABLE_IRQ1
+ // #define GPIO_ENABLE_IRQ2
+ // #define GPIO_ENABLE_IRQ3
+ #endif
/*=========================================================================*/
#define CFG_UART_BAUDRATE (115200)
#define CFG_UART_BUFSIZE (512)
#endif
+
+ #ifdef CFG_BRD_LPC1343_LPCXPRESSO
+ #define CFG_UART_BAUDRATE (115200)
+ #define CFG_UART_BUFSIZE (512)
+ #endif
/*=========================================================================*/
#define CFG_SSP0_SCKPIN_2_11
// #define CFG_SSP0_SCKPIN_0_6
#endif
+
+ #ifdef CFG_BRD_LPC1343_LPCXPRESSO
+ #define CFG_SSP0_SCKPIN_2_11
+ // #define CFG_SSP0_SCKPIN_0_6
+ #endif
/*=========================================================================*/
#define ADC_AVERAGING_ENABLE (0)
#define ADC_AVERAGING_SAMPLES (5)
#endif
+
+ #ifdef CFG_BRD_LPC1343_LPCXPRESSO
+ #define ADC_AVERAGING_ENABLE (0)
+ #define ADC_AVERAGING_SAMPLES (5)
+ #endif
/*=========================================================================*/
#define CFG_LED_ON (0)
#define CFG_LED_OFF (1)
#endif
+
+ #ifdef CFG_BRD_LPC1343_LPCXPRESSO
+ #define CFG_LED_PORT (0)
+ #define CFG_LED_PIN (7)
+ #define CFG_LED_ON (0)
+ #define CFG_LED_OFF (1)
+ #endif
/*=========================================================================*/
#define CFG_SDCARD_CDPORT (3)
#define CFG_SDCARD_CDPIN (0)
#endif
+
+ #ifdef CFG_BRD_LPC1343_LPCXPRESSO
+ // #define CFG_SDCARD
+ #define CFG_SDCARD_READONLY (1) // Must be 0 or 1
+ #define CFG_SDCARD_CDPORT (3)
+ #define CFG_SDCARD_CDPIN (0)
+ #endif
/*=========================================================================*/
#define CFG_USBCDC_INITTIMEOUT (5000)
#define CFG_USBCDC_BUFFERSIZE (256)
#endif
+
+ #ifdef CFG_BRD_LPC1343_LPCXPRESSO
+ // #define CFG_USBHID
+ #define CFG_USBCDC
+ #define CFG_USBCDC_BAUDRATE (115200)
+ #define CFG_USBCDC_INITTIMEOUT (5000)
+ #define CFG_USBCDC_BUFFERSIZE (256)
+ #endif
/*=========================================================================*/
PRINTF REDIRECTION
-----------------------------------------------------------------------
+ CFG_PRINTF_MAXSTRINGSIZE Maximum size of string buffer for printf
CFG_PRINTF_UART Will cause all printf statements to be
redirected to UART
CFG_PRINTF_USBCDC Will cause all printf statements to be
output will be ignored.
-----------------------------------------------------------------------*/
#ifdef CFG_BRD_LPC1343_REFDESIGN
+ #define CFG_PRINTF_MAXSTRINGSIZE (255)
// #define CFG_PRINTF_UART
#define CFG_PRINTF_USBCDC
#define CFG_PRINTF_NEWLINE "\r\n"
#endif
#ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
+ #define CFG_PRINTF_MAXSTRINGSIZE (255)
#define CFG_PRINTF_UART
// #define CFG_PRINTF_USBCDC
#define CFG_PRINTF_NEWLINE "\r\n"
#endif
#ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
+ #define CFG_PRINTF_MAXSTRINGSIZE (255)
// #define CFG_PRINTF_UART
#define CFG_PRINTF_USBCDC
#define CFG_PRINTF_NEWLINE "\r\n"
#endif
#ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
+ #define CFG_PRINTF_MAXSTRINGSIZE (255)
#define CFG_PRINTF_UART
// #define CFG_PRINTF_USBCDC
#define CFG_PRINTF_NEWLINE "\n"
#endif
#ifdef CFG_BRD_LPC1343_802154USBSTICK
+ #define CFG_PRINTF_MAXSTRINGSIZE (255)
// #define CFG_PRINTF_UART
#define CFG_PRINTF_USBCDC
#define CFG_PRINTF_NEWLINE "\r\n"
#endif
#ifdef CFG_BRD_LPC1343_OLIMEX_P
+ #define CFG_PRINTF_MAXSTRINGSIZE (255)
// #define CFG_PRINTF_UART
#define CFG_PRINTF_USBCDC
#define CFG_PRINTF_NEWLINE "\r\n"
#endif
+
+ #ifdef CFG_BRD_LPC1343_LPCXPRESSO
+ #define CFG_PRINTF_MAXSTRINGSIZE (255)
+ // #define CFG_PRINTF_UART
+ #define CFG_PRINTF_USBCDC
+ #define CFG_PRINTF_NEWLINE "\r\n"
+ #endif
/*=========================================================================*/
addition to CFG_INTERFACE_ENABLEIRQ if
this is also enabled. The character used
is defined below.
+ CFG_INTERFACE_LONGSYSINFO If this is set to 1 extra information will
+ be included in the Sys Info ('V') command
+ on the CLI. This can be useful when trying
+ to debug problems on remote HW, or with
+ unknown firmware. It will also use about
+ 0.5KB flash, though, so only enable it is
+ necessary.
NOTE: The command-line interface will use either
USB-CDC or UART depending on whether
#define CFG_INTERFACE_IRQPIN (7)
#define CFG_INTERFACE_SHORTERRORS (0)
#define CFG_INTERFACE_CONFIRMREADY (0)
+ #define CFG_INTERFACE_LONGSYSINFO (0)
#endif
#ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
#define CFG_INTERFACE_IRQPIN (7)
#define CFG_INTERFACE_SHORTERRORS (0)
#define CFG_INTERFACE_CONFIRMREADY (0)
+ #define CFG_INTERFACE_LONGSYSINFO (0)
#endif
#ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
#define CFG_INTERFACE_SHORTERRORS_TOOMANYARGS ">"
#define CFG_INTERFACE_SHORTERRORS_TOOFEWARGS "<"
#define CFG_INTERFACE_CONFIRMREADY_TEXT "."
+ #define CFG_INTERFACE_LONGSYSINFO (0)
#endif
#ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
#define CFG_INTERFACE_SHORTERRORS_TOOMANYARGS ">"
#define CFG_INTERFACE_SHORTERRORS_TOOFEWARGS "<"
#define CFG_INTERFACE_CONFIRMREADY_TEXT "."
+ #define CFG_INTERFACE_LONGSYSINFO (0)
#endif
#ifdef CFG_BRD_LPC1343_802154USBSTICK
#define CFG_INTERFACE_IRQPIN (7)
#define CFG_INTERFACE_SHORTERRORS (0)
#define CFG_INTERFACE_CONFIRMREADY (0)
+ #define CFG_INTERFACE_LONGSYSINFO (0)
#endif
#ifdef CFG_BRD_LPC1343_OLIMEX_P
#define CFG_INTERFACE_IRQPIN (7)
#define CFG_INTERFACE_SHORTERRORS (0)
#define CFG_INTERFACE_CONFIRMREADY (0)
+ #define CFG_INTERFACE_LONGSYSINFO (0)
+ #endif
+
+ #ifdef CFG_BRD_LPC1343_LPCXPRESSO
+ #define CFG_INTERFACE
+ #define CFG_INTERFACE_MAXMSGSIZE (256)
+ #define CFG_INTERFACE_PROMPT "LPC-P1343 >> "
+ #define CFG_INTERFACE_SILENTMODE (0)
+ #define CFG_INTERFACE_DROPCR (0)
+ #define CFG_INTERFACE_ENABLEIRQ (0)
+ #define CFG_INTERFACE_IRQPORT (0)
+ #define CFG_INTERFACE_IRQPIN (7)
+ #define CFG_INTERFACE_SHORTERRORS (0)
+ #define CFG_INTERFACE_CONFIRMREADY (0)
+ #define CFG_INTERFACE_LONGSYSINFO (0)
#endif
/*=========================================================================*/
// #define CFG_I2CEEPROM
#define CFG_I2CEEPROM_SIZE (3072)
#endif
+
+ #ifdef CFG_BRD_LPC1343_LPCXPRESSO
+ // #define CFG_I2CEEPROM
+ #define CFG_I2CEEPROM_SIZE (3072)
+ #endif
/*=========================================================================*/
#define CFG_CHIBI_PROMISCUOUS (0)
#define CFG_CHIBI_BUFFERSIZE (128)
#endif
+
+ #ifdef CFG_BRD_LPC1343_LPCXPRESSO
+ // #define CFG_CHIBI
+ #define CFG_CHIBI_MODE (0) // OQPSK_868MHZ
+ #define CFG_CHIBI_POWER (0xE9) // CHB_PWR_EU2_3DBM
+ #define CFG_CHIBI_CHANNEL (0) // 868-868.6 MHz
+ #define CFG_CHIBI_PANID (0x1234)
+ #define CFG_CHIBI_PROMISCUOUS (0)
+ #define CFG_CHIBI_BUFFERSIZE (128)
+ #endif
/*=========================================================================*/
support for larger fonts generated with
Dot Factory
http://www.pavius.net/downloads/tools/53-the-dot-factory
+ CFG_TFTLCD_USEAAFONTS If set to a non-zero value, anti-aliased
+ fonts will be used instead of regular 1-bit
+ font. These result in much higher-
+ quality text, but the fonts are 2 or 4
+ times larger than plain bitmap fonts and
+ take a bit more rendering time to display.
CFG_TFTLCD_TS_DEFAULTTHRESHOLD Default minimum threshold to trigger a
touch event with the touch screen (and exit
from 'tsWaitForEvent' in touchscreen.c).
#ifdef CFG_BRD_LPC1343_REFDESIGN
// #define CFG_TFTLCD
#define CFG_TFTLCD_INCLUDESMALLFONTS (0)
+ #define CFG_TFTLCD_USEAAFONTS (0)
#define CFG_TFTLCD_TS_DEFAULTTHRESHOLD (50)
#define CFG_TFTLCD_TS_KEYPADDELAY (100)
#endif
#ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
// #define CFG_TFTLCD
#define CFG_TFTLCD_INCLUDESMALLFONTS (0)
+ #define CFG_TFTLCD_USEAAFONTS (0)
#define CFG_TFTLCD_TS_DEFAULTTHRESHOLD (50)
#define CFG_TFTLCD_TS_KEYPADDELAY (100)
#endif
#if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
#define CFG_TFTLCD
#define CFG_TFTLCD_INCLUDESMALLFONTS (0)
+ #define CFG_TFTLCD_USEAAFONTS (0)
#define CFG_TFTLCD_TS_DEFAULTTHRESHOLD (50)
#define CFG_TFTLCD_TS_KEYPADDELAY (100)
#endif
#ifdef CFG_BRD_LPC1343_802154USBSTICK
// #define CFG_TFTLCD
#define CFG_TFTLCD_INCLUDESMALLFONTS (0)
+ #define CFG_TFTLCD_USEAAFONTS (0)
#define CFG_TFTLCD_TS_DEFAULTTHRESHOLD (50)
#define CFG_TFTLCD_TS_KEYPADDELAY (100)
#endif
#ifdef CFG_BRD_LPC1343_OLIMEX_P
// #define CFG_TFTLCD
#define CFG_TFTLCD_INCLUDESMALLFONTS (0)
+ #define CFG_TFTLCD_USEAAFONTS (0)
#define CFG_TFTLCD_TS_DEFAULTTHRESHOLD (50)
#define CFG_TFTLCD_TS_KEYPADDELAY (100)
#endif
+
+ #ifdef CFG_BRD_LPC1343_LPCXPRESSO
+ // #define CFG_TFTLCD
+ #define CFG_TFTLCD_INCLUDESMALLFONTS (0)
+ #define CFG_TFTLCD_USEAAFONTS (0)
+ #define CFG_TFTLCD_TS_DEFAULTTHRESHOLD (50)
+ #define CFG_TFTLCD_TS_KEYPADDELAY (100)
+ #endif
/*=========================================================================*/
the 128x64 pixel ST7565 LCD to be included
CFG_SSD1306 If defined, this will cause drivers for
the 128x64 pixel SSD1306 OLED display to be
- included
+ included (using bit-banged SPI)
CFG_SHARPMEM If defined, this will cause drivers for
Sharp Memory Displays to be included
DEPENDENCIES: ST7565 requires the use of pins 2.1-6.
DEPENDENCIES: SSD1306 requires the use of pins 2.1-6.
+ DEPENDENCIES: SSD1306_I2C requires the use of pins 2.2.
DEPENDENCIES: SHARPMEM requires the use of pins 2.1-4.
-----------------------------------------------------------------------*/
// #define CFG_ST7565
!defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB && \
!defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART && \
!defined CFG_BRD_LPC1343_802154USBSTICK && \
- !defined CFG_BRD_LPC1343_OLIMEX_P
- #error "You must defined a target board (CFG_BRD_LPC1343_REFDESIGN or CFG_BRD_LPC1343_REFDESIGN_MINIMAL or CFG_BRD_LPC1343_TFTLCDSTANDALONE or CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART or CFG_BRD_LPC1343_802154USBSTICK)"
+ !defined CFG_BRD_LPC1343_OLIMEX_P && \
+ !defined CFG_BRD_LPC1343_LPCXPRESSO
+ #error "You must defined a target board (CFG_BRD_LPC1343_REFDESIGN or CFG_BRD_LPC1343_REFDESIGN_MINIMAL or CFG_BRD_LPC1343_TFTLCDSTANDALONE or CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART or CFG_BRD_LPC1343_802154USBSTICK or CFG_BRD_LPC1343_LPCXPRESSO)"
#endif
#if defined CFG_PRINTF_USBCDC && defined CFG_PRINTF_UART
projects / hackover2013-badge-firmware.git / blobdiff