package/mac80211/patches/001-disable_drivers.patch

   1 Index: compat-wireless-2008-05-26/config.mk
   2 ===================================================================
   3 --- compat-wireless-2008-05-26.orig/config.mk   2008-05-27 19:15:19.000000000 +0100
   4 +++ compat-wireless-2008-05-26/config.mk        2008-05-27 19:52:31.000000000 +0100
   5 @@ -28,73 +28,6 @@ CONFIG_NL80211=y
   6  # PCI Drivers
   7  ifneq ($(CONFIG_PCI),)
   8
   9 -CONFIG_ATH5K=m
  10 -CONFIG_ATH5K_DEBUG=n
  11 -
  12 -# Required for older kernels which still use this flag.
  13 -CONFIG_IWLWIFI=m
  14 -
  15 -CONFIG_IWLCORE=m
  16 -CONFIG_IWL3945=m
  17 -CONFIG_IWL4965=m
  18 -CONFIG_IWL4965_HT=y
  19 -CONFIG_B43=m
  20 -# B43 uses PCMCIA only for Compact Flash. The Cardbus cards uses PCI
  21 -# Example, bcm4318:
  22 -# http://www.multicap.biz/wireless-lan/indoor-wlan-hardware/sdc-cf10g-80211g-compact-flash-module
  23 -CONFIG_B43_PCMCIA=y
  24 -CONFIG_B43_DMA=y
  25 -CONFIG_B43_PIO=y
  26 -# B43_PIO selects SSB_BLOCKIO
  27 -CONFIG_SSB_BLOCKIO=y
  28 -CONFIG_B43_DMA_AND_PIO_MODE=y
  29 -CONFIG_B43_PCI_AUTOSELECT=y
  30 -CONFIG_B43_PCICORE_AUTOSELECT=y
  31 -#CONFIG_B43_RFKILL=n
  32 -CONFIG_B43_LEDS=y
  33 -# CONFIG_B43_DEBUG is not set
  34 -
  35 -CONFIG_B43LEGACY=m
  36 -CONFIG_B43LEGACY_PCI_AUTOSELECT=y
  37 -CONFIG_B43LEGACY_PCICORE_AUTOSELECT=y
  38 -CONFIG_B43LEGACY_DMA=y
  39 -CONFIG_B43LEGACY_PIO=y
  40 -CONFIG_B43LEGACY_DMA_AND_PIO_MODE=y
  41 -
  42 -# The Intel ipws
  43 -CONFIG_IPW2100=m
  44 -CONFIG_IPW2100_MONITOR=y
  45 -CONFIG_IPW2200=m
  46 -CONFIG_IPW2200_MONITOR=y
  47 -CONFIG_IPW2200_RADIOTAP=y
  48 -CONFIG_IPW2200_PROMISCUOUS=y
  49 -# The above enables use a second interface prefixed 'rtap'.
  50 -#           Example usage:
  51 -#
  52 -# % modprobe ipw2200 rtap_iface=1
  53 -# % ifconfig rtap0 up
  54 -# % tethereal -i rtap0
  55 -#
  56 -# If you do not specify 'rtap_iface=1' as a module parameter then
  57 -# the rtap interface will not be created and you will need to turn
  58 -# it on via sysfs:
  59 -#
  60 -# % echo 1 > /sys/bus/pci/drivers/ipw2200/*/rtap_iface
  61 -CONFIG_IPW2200_QOS=y
  62 -
  63 -NEED_IEEE80211=y
  64 -
  65 -CONFIG_P54_PCI=m
  66 -
  67 -CONFIG_SSB_PCIHOST_POSSIBLE=y
  68 -CONFIG_SSB_PCIHOST=y
  69 -CONFIG_SSB_DRIVER_PCICORE_POSSIBLE=y
  70 -CONFIG_SSB_DRIVER_PCICORE=y
  71 -CONFIG_SSB_B43_PCI_BRIDGE=y
  72 -
  73 -CONFIG_RTL8180=m
  74 -CONFIG_ADM8211=m
  75 -
  76  CONFIG_RT2X00_LIB_PCI=m
  77  CONFIG_RT2400PCI=m
  78  CONFIG_RT2500PCI=m
  79 @@ -116,33 +49,6 @@ CONFIG_EEPROM_93CX6=m
  80
  81  # USB Drivers
  82  ifneq ($(CONFIG_USB),)
  83 -CONFIG_ZD1211RW=m
  84 -
  85 -# support for USB Wireless devices using Atmel at76c503,
  86 -# at76c505 or at76c505a chips.
  87 -CONFIG_USB_ATMEL=m
  88 -
  89 -# Stuff here things which depend on kernel versions for USB
  90 -ifeq ($(shell test -e $(KLIB_BUILD)/Makefile && echo yes),yes)
  91 -KERNEL_SUBLEVEL = $(shell $(MAKE) -C $(KLIB_BUILD) kernelversion | sed -n 's/^2\.6\.\([0-9]\+\).*/\1/p')
  92 -ifeq ($(shell test $(KERNEL_SUBLEVEL) -gt 21 && echo yes),yes)
  93 -
  94 -# Sorry, rndis_wlan uses cancel_work_sync which is new and can't be done in compat...
  95 -
  96 -# Wireless RNDIS USB support (RTL8185 802.11g) A-Link WL54PC
  97 -# All of these devices are based on Broadcom 4320 chip which
  98 -# is only wireless RNDIS chip known to date.
  99 -# Note: this depends on CONFIG_USB_NET_RNDIS_HOST and CONFIG_USB_NET_CDCETHER
 100 -# it also requires new RNDIS_HOST and CDC_ETHER modules which we add
 101 -CONFIG_USB_NET_RNDIS_HOST=m
 102 -CONFIG_USB_NET_RNDIS_WLAN=m
 103 -CONFIG_USB_NET_CDCETHER=m
 104 -
 105 -endif
 106 -endif
 107 -
 108 -CONFIG_P54_USB=m
 109 -CONFIG_RTL8187=m
 110
 111  # RT2500USB does not require firmware
 112  CONFIG_RT2500USB=m
 113 @@ -168,39 +74,6 @@ ifeq ($(NEED_RT2X00_FIRMWARE),y)
 114  CONFIG_RT2X00_LIB_FIRMWARE=y
 115  endif
 116
 117 -# p54
 118 -CONFIG_P54_COMMON=m
 119 -
 120 -# Sonics Silicon Backplane
 121 -CONFIG_SSB_POSSIBLE=y
 122 -CONFIG_SSB=m
 123 -CONFIG_SSB_SPROM=y
 124 -
 125 -ifneq ($(CONFIG_PCMCIA),)
 126 -CONFIG_SSB_PCMCIAHOST=y
 127 -endif
 128 -
 129 -# These two are for mips
 130 -CONFIG_SSB_DRIVER_MIPS=n
 131 -CONFIG_SSB_PCICORE_HOSTMODE=n
 132 -# CONFIG_SSB_DEBUG is not set
 133 -# CONFIG_SSB_DRIVER_EXTIF=y
 134 -
 135 -ifneq ($(CONFIG_USB),)
 136 -CONFIG_LIBERTAS_USB=m
 137 -NEED_LIBERTAS=y
 138 -endif
 139 -ifneq ($(CONFIG_PCMCIA),)
 140 -CONFIG_LIBERTAS_CS=m
 141 -NEED_LIBERTAS=y
 142 -endif
 143 -ifeq ($(NEED_LIBERTAS),y)
 144 -CONFIG_LIBERTAS=m
 145 -# Libertas uses the old stack but not fully, it will soon
 146 -# be cleaned.
 147 -NEED_IEEE80211=y
 148 -endif
 149 -
 150  ifeq ($(NEED_IEEE80211),y)
 151  # Old ieee80211 "stack"
 152  # Note: old softmac is scheduled for removal so we