target/linux/ixp4xx-2.6/patches/200-gateway_7001.patch

   1 diff -Nur linux-2.6.19.2/arch/arm/boot/compressed/head-xscale.S linux-2.6.19.2-owrt/arch/arm/boot/compressed/head-xscale.S
   2 --- linux-2.6.19.2/arch/arm/boot/compressed/head-xscale.S       2007-01-10 20:10:37.000000000 +0100
   3 +++ linux-2.6.19.2-owrt/arch/arm/boot/compressed/head-xscale.S  2007-04-02 15:39:28.000000000 +0200
   4 @@ -46,6 +46,11 @@
   5                 orr     r7, r7, #(MACH_TYPE_GTWX5715 & 0xff00)
   6  #endif
   7
   8 +#ifdef  CONFIG_MACH_GATEWAY7001
   9 +               mov     r7, #(MACH_TYPE_GATEWAY7001 & 0xff)
  10 +               orr     r7, r7, #(MACH_TYPE_GATEWAY7001 & 0xff00)
  11 +#endif
  12 +
  13  #ifdef CONFIG_ARCH_IXP2000
  14                 mov     r1, #-1
  15                 mov     r0, #0xd6000000
  16 diff -Nur linux-2.6.19.2/arch/arm/mach-ixp4xx/gateway7001-pci.c linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/gateway7001-pci.c
  17 --- linux-2.6.19.2/arch/arm/mach-ixp4xx/gateway7001-pci.c       1970-01-01 01:00:00.000000000 +0100
  18 +++ linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/gateway7001-pci.c  2007-04-02 15:39:28.000000000 +0200
  19 @@ -0,0 +1,68 @@
  20 +/*
  21 + * arch/arch/mach-ixp4xx/gateway7001-pci.c
  22 + *
  23 + * PCI setup routines for Gateway 7001
  24 + *
  25 + * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
  26 + *
  27 + * based on coyote-pci.c:
  28 + *     Copyright (C) 2002 Jungo Software Technologies.
  29 + *     Copyright (C) 2003 MontaVista Softwrae, Inc.
  30 + *
  31 + * Maintainer: Imre Kaloz <kaloz@openwrt.org>
  32 + *
  33 + * This program is free software; you can redistribute it and/or modify
  34 + * it under the terms of the GNU General Public License version 2 as
  35 + * published by the Free Software Foundation.
  36 + *
  37 + */
  38 +
  39 +#include <linux/kernel.h>
  40 +#include <linux/pci.h>
  41 +#include <linux/init.h>
  42 +#include <linux/irq.h>
  43 +
  44 +#include <asm/mach-types.h>
  45 +#include <asm/hardware.h>
  46 +#include <asm/irq.h>
  47 +
  48 +#include <asm/mach/pci.h>
  49 +
  50 +extern void ixp4xx_pci_preinit(void);
  51 +extern int ixp4xx_setup(int nr, struct pci_sys_data *sys);
  52 +extern struct pci_bus *ixp4xx_scan_bus(int nr, struct pci_sys_data *sys);
  53 +
  54 +void __init gateway7001_pci_preinit(void)
  55 +{
  56 +       set_irq_type(IRQ_IXP4XX_GPIO10, IRQT_LOW);
  57 +       set_irq_type(IRQ_IXP4XX_GPIO11, IRQT_LOW);
  58 +
  59 +       ixp4xx_pci_preinit();
  60 +}
  61 +
  62 +static int __init gateway7001_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
  63 +{
  64 +       if (slot == 1)
  65 +               return IRQ_IXP4XX_GPIO11;
  66 +       else if (slot == 2)
  67 +               return IRQ_IXP4XX_GPIO10;
  68 +       else return -1;
  69 +}
  70 +
  71 +struct hw_pci gateway7001_pci __initdata = {
  72 +       .nr_controllers = 1,
  73 +       .preinit =        gateway7001_pci_preinit,
  74 +       .swizzle =        pci_std_swizzle,
  75 +       .setup =          ixp4xx_setup,
  76 +       .scan =           ixp4xx_scan_bus,
  77 +       .map_irq =        gateway7001_map_irq,
  78 +};
  79 +
  80 +int __init gateway7001_pci_init(void)
  81 +{
  82 +       if (machine_is_gateway7001())
  83 +               pci_common_init(&gateway7001_pci);
  84 +       return 0;
  85 +}
  86 +
  87 +subsys_initcall(gateway7001_pci_init);
  88 diff -Nur linux-2.6.19.2/arch/arm/mach-ixp4xx/gateway7001-setup.c linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/gateway7001-setup.c
  89 --- linux-2.6.19.2/arch/arm/mach-ixp4xx/gateway7001-setup.c     1970-01-01 01:00:00.000000000 +0100
  90 +++ linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/gateway7001-setup.c        2007-04-02 15:49:28.000000000 +0200
  91 @@ -0,0 +1,108 @@
  92 +/*
  93 + * arch/arm/mach-ixp4xx/gateway7001-setup.c
  94 + *
  95 + * Board setup for the Gateway 7001 board
  96 + *
  97 + * Copyright (C) 2006 Imre Kaloz <Kaloz@openwrt.org>
  98 + *
  99 + * based on coyote-setup.c:
 100 + *      Copyright (C) 2003-2005 MontaVista Software, Inc.
 101 + *
 102 + * Author: Imre Kaloz <Kaloz@openwrt.org>
 103 + */
 104 +
 105 +#include <linux/kernel.h>
 106 +#include <linux/init.h>
 107 +#include <linux/device.h>
 108 +#include <linux/serial.h>
 109 +#include <linux/tty.h>
 110 +#include <linux/serial_8250.h>
 111 +#include <linux/slab.h>
 112 +
 113 +#include <asm/types.h>
 114 +#include <asm/setup.h>
 115 +#include <asm/memory.h>
 116 +#include <asm/hardware.h>
 117 +#include <asm/irq.h>
 118 +#include <asm/mach-types.h>
 119 +#include <asm/mach/arch.h>
 120 +#include <asm/mach/flash.h>
 121 +
 122 +static struct flash_platform_data gateway7001_flash_data = {
 123 +       .map_name       = "cfi_probe",
 124 +       .width          = 2,
 125 +};
 126 +
 127 +static struct resource gateway7001_flash_resource = {
 128 +       .flags          = IORESOURCE_MEM,
 129 +};
 130 +
 131 +static struct platform_device gateway7001_flash = {
 132 +       .name           = "IXP4XX-Flash",
 133 +       .id             = 0,
 134 +       .dev            = {
 135 +               .platform_data = &gateway7001_flash_data,
 136 +       },
 137 +       .num_resources  = 1,
 138 +       .resource       = &gateway7001_flash_resource,
 139 +};
 140 +
 141 +static struct resource gateway7001_uart_resource = {
 142 +       .start  = IXP4XX_UART2_BASE_PHYS,
 143 +       .end    = IXP4XX_UART2_BASE_PHYS + 0x0fff,
 144 +       .flags  = IORESOURCE_MEM,
 145 +};
 146 +
 147 +static struct plat_serial8250_port gateway7001_uart_data[] = {
 148 +       {
 149 +               .mapbase        = IXP4XX_UART2_BASE_PHYS,
 150 +               .membase        = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
 151 +               .irq            = IRQ_IXP4XX_UART2,
 152 +               .flags          = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
 153 +               .iotype         = UPIO_MEM,
 154 +               .regshift       = 2,
 155 +               .uartclk        = IXP4XX_UART_XTAL,
 156 +       },
 157 +       { },
 158 +};
 159 +
 160 +static struct platform_device gateway7001_uart = {
 161 +       .name           = "serial8250",
 162 +       .id             = PLAT8250_DEV_PLATFORM,
 163 +       .dev                    = {
 164 +               .platform_data  = gateway7001_uart_data,
 165 +       },
 166 +       .num_resources  = 1,
 167 +       .resource       = &gateway7001_uart_resource,
 168 +};
 169 +
 170 +static struct platform_device *gateway7001_devices[] __initdata = {
 171 +       &gateway7001_flash,
 172 +       &gateway7001_uart
 173 +};
 174 +
 175 +static void __init gateway7001_init(void)
 176 +{
 177 +       ixp4xx_sys_init();
 178 +
 179 +       gateway7001_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
 180 +       gateway7001_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1;
 181 +
 182 +       *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
 183 +       *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
 184 +
 185 +       platform_add_devices(gateway7001_devices, ARRAY_SIZE(gateway7001_devices));
 186 +}
 187 +
 188 +#ifdef CONFIG_MACH_GATEWAY7001
 189 +MACHINE_START(GATEWAY7001, "Gateway 7001 AP")
 190 +       /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
 191 +       .phys_io        = IXP4XX_PERIPHERAL_BASE_PHYS,
 192 +       .io_pg_offst    = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
 193 +       .map_io         = ixp4xx_map_io,
 194 +       .init_irq       = ixp4xx_init_irq,
 195 +       .timer          = &ixp4xx_timer,
 196 +       .boot_params    = 0x0100,
 197 +       .init_machine   = gateway7001_init,
 198 +MACHINE_END
 199 +#endif
 200 diff -Nur linux-2.6.19.2/arch/arm/mach-ixp4xx/Kconfig linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/Kconfig
 201 --- linux-2.6.19.2/arch/arm/mach-ixp4xx/Kconfig 2007-01-10 20:10:37.000000000 +0100
 202 +++ linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/Kconfig    2007-04-02 15:39:28.000000000 +0200
 203 @@ -33,6 +33,14 @@
 204           Engineering Coyote Gateway Reference Platform. For more
 205           information on this platform, see <file:Documentation/arm/IXP4xx>.
 206
 207 +config MACH_GATEWAY7001
 208 +       bool "Gateway 7001"
 209 +       select PCI
 210 +       help
 211 +         Say 'Y' here if you want your kernel to support Gateway's
 212 +         7001 Access Point. For more information on this platform,
 213 +         see http://openwrt.org
 214 +
 215  config ARCH_IXDP425
 216         bool "IXDP425"
 217         help
 218 diff -Nur linux-2.6.19.2/arch/arm/mach-ixp4xx/Makefile linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/Makefile
 219 --- linux-2.6.19.2/arch/arm/mach-ixp4xx/Makefile        2007-01-10 20:10:37.000000000 +0100
 220 +++ linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/Makefile   2007-04-02 15:49:49.000000000 +0200
 221 @@ -11,6 +11,7 @@
 222  obj-pci-$(CONFIG_MACH_NSLU2)           += nslu2-pci.o
 223  obj-pci-$(CONFIG_MACH_NAS100D)         += nas100d-pci.o
 224  obj-pci-$(CONFIG_MACH_DSMG600)         += dsmg600-pci.o
 225 +obj-pci-$(CONFIG_MACH_GATEWAY7001)     += gateway7001-pci.o
 226
 227  obj-y  += common.o
 228
 229 @@ -20,5 +21,6 @@
 230  obj-$(CONFIG_MACH_NSLU2)       += nslu2-setup.o nslu2-power.o
 231  obj-$(CONFIG_MACH_NAS100D)     += nas100d-setup.o nas100d-power.o
 232  obj-$(CONFIG_MACH_DSMG600)      += dsmg600-setup.o dsmg600-power.o
 233 +obj-$(CONFIG_MACH_GATEWAY7001) += gateway7001-setup.o
 234
 235  obj-$(CONFIG_PCI)              += $(obj-pci-$(CONFIG_PCI)) common-pci.o
 236 diff -Nur linux-2.6.19.2/include/asm-arm/arch-ixp4xx/uncompress.h linux-2.6.19.2-owrt/include/asm-arm/arch-ixp4xx/uncompress.h
 237 --- linux-2.6.19.2/include/asm-arm/arch-ixp4xx/uncompress.h     2007-01-10 20:10:37.000000000 +0100
 238 +++ linux-2.6.19.2-owrt/include/asm-arm/arch-ixp4xx/uncompress.h        2007-04-02 15:42:04.000000000 +0200
 239 @@ -38,9 +38,9 @@
 240  static __inline__ void __arch_decomp_setup(unsigned long arch_id)
 241  {
 242         /*
 243 -        * Coyote and gtwx5715 only have UART2 connected
 244 +        * Some boards are using UART2 as console
 245          */
 246 -       if (machine_is_adi_coyote() || machine_is_gtwx5715())
 247 +       if (machine_is_adi_coyote() || machine_is_gtwx5715() || machine_is_gateway7001())
 248                 uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS;
 249         else
 250                 uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS;