ramips: ramips_esw: don't touch GPIO_PURPOSE register

It must have been set by the board initialization code.

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24332 3c298f89-4303-0410-b956-a3cf2f4a3e73

diff --git a/target/linux/ramips/files/drivers/net/ramips_esw.c b/target/linux/ramips/files/drivers/net/ramips_esw.c
index 87479c6..23f9e48 100644 (file)
--- a/target/linux/ramips/files/drivers/net/ramips_esw.c
+++ b/target/linux/ramips/files/drivers/net/ramips_esw.c
@@ -3,8 +3,6 @@
 #include <rt305x_regs.h>
 #include <rt305x_esw_platform.h>
 
-#define GPIO_PRUPOSE           0x60
-#define GPIO_MDIO_BIT          (1<<7)
 #define RT305X_ESW_PHY_WRITE           (1 << 13)
 #define RT305X_ESW_PHY_TOUT                    (5 * HZ)
 #define RT305X_ESW_PHY_CONTROL_0       0xC0
@@ -27,17 +25,6 @@ ramips_esw_rr(struct rt305x_esw *esw, unsigned reg)
        return __raw_readl(esw->base + reg);
 }
 
-static void
-ramips_enable_mdio(int s)
-{
-       u32 gpio = rt305x_sysc_rr(GPIO_PRUPOSE);
-       if(s)
-               gpio &= ~GPIO_MDIO_BIT;
-       else
-               gpio |= GPIO_MDIO_BIT;
-       rt305x_sysc_wr(gpio, GPIO_PRUPOSE);
-}
-
 u32
 mii_mgr_write(struct rt305x_esw *esw, u32 phy_addr, u32 phy_register,
              u32 write_data)
@@ -45,7 +32,6 @@ mii_mgr_write(struct rt305x_esw *esw, u32 phy_addr, u32 phy_register,
        unsigned long volatile t_start = jiffies;
        int ret = 0;
 
-       ramips_enable_mdio(1);
        while(1)
        {
                if(!(ramips_esw_rr(esw, RT305X_ESW_PHY_CONTROL_1) & (0x1 << 0)))
@@ -70,7 +56,6 @@ mii_mgr_write(struct rt305x_esw *esw, u32 phy_addr, u32 phy_register,
                }
        }
 out:
-       ramips_enable_mdio(0);
        if(ret)
                printk(KERN_ERR "ramips_eth: MDIO timeout\n");
        return ret;
@@ -111,11 +96,6 @@ rt305x_esw_hw_init(struct rt305x_esw *esw)
        mii_mgr_write(esw, 0, 14, 0x65);     //longer TP_IDL tail length
        mii_mgr_write(esw, 0, 31, 0x8000);   //select local register
 
-       /* Port 5 Disabled */
-       rt305x_sysc_wr(rt305x_sysc_rr(0x60) | (1 << 9), 0x60); //set RGMII to GPIO mode (GPIO41-GPIO50)
-       rt305x_sysc_wr(0xfff, 0x674); //GPIO41-GPIO50 output mode
-       rt305x_sysc_wr(0x0, 0x670); //GPIO41-GPIO50 output low
-
        /* set default vlan */
        ramips_esw_wr(esw, 0x2001, 0x50);
        ramips_esw_wr(esw, 0x504f, 0x70);