+++ /dev/null
-CONFIG_32BIT=y
-# CONFIG_64BIT is not set
-CONFIG_AR7_GPIO=y
-CONFIG_AR7_WDT=y
-CONFIG_AR7=y
-# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-# CONFIG_ARCH_HAS_ILOG2_U64 is not set
-CONFIG_ARCH_POPULATES_NODE_MAP=y
-# CONFIG_ARCH_SUPPORTS_MSI is not set
-CONFIG_ARCH_SUPPORTS_OPROFILE=y
-CONFIG_ARCH_SUSPEND_POSSIBLE=y
-CONFIG_BASE_SMALL=0
-# CONFIG_BCM47XX is not set
-CONFIG_BITREVERSE=y
-CONFIG_BOOT_ELF32=y
-CONFIG_CEVT_R4K=y
-CONFIG_CLASSIC_RCU=y
-CONFIG_CMDLINE="rootfstype=squashfs,jffs2"
-CONFIG_CPMAC=y
-# CONFIG_CPU_BIG_ENDIAN is not set
-CONFIG_CPU_HAS_LLSC=y
-CONFIG_CPU_HAS_PREFETCH=y
-CONFIG_CPU_HAS_SYNC=y
-CONFIG_CPU_LITTLE_ENDIAN=y
-# CONFIG_CPU_LOONGSON2 is not set
-CONFIG_CPU_MIPS32_R1=y
-# CONFIG_CPU_MIPS32_R2 is not set
-CONFIG_CPU_MIPS32=y
-# CONFIG_CPU_MIPS64_R1 is not set
-# CONFIG_CPU_MIPS64_R2 is not set
-CONFIG_CPU_MIPSR1=y
-# CONFIG_CPU_NEVADA is not set
-# CONFIG_CPU_R10000 is not set
-# CONFIG_CPU_R3000 is not set
-# CONFIG_CPU_R4300 is not set
-# CONFIG_CPU_R4X00 is not set
-# CONFIG_CPU_R5000 is not set
-# CONFIG_CPU_R5432 is not set
-# CONFIG_CPU_R6000 is not set
-# CONFIG_CPU_R8000 is not set
-# CONFIG_CPU_RM7000 is not set
-# CONFIG_CPU_RM9000 is not set
-# CONFIG_CPU_SB1 is not set
-CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
-CONFIG_CPU_SUPPORTS_HIGHMEM=y
-# CONFIG_CPU_TX39XX is not set
-# CONFIG_CPU_TX49XX is not set
-# CONFIG_CPU_VR41XX is not set
-CONFIG_CSRC_R4K=y
-# CONFIG_DM9000 is not set
-CONFIG_DMA_NEED_PCI_MAP_STATE=y
-CONFIG_DMA_NONCOHERENT=y
-CONFIG_EARLY_PRINTK=y
-CONFIG_FIXED_PHY=y
-CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_GENERIC_CMOS_UPDATE=y
-# CONFIG_GENERIC_FIND_FIRST_BIT is not set
-CONFIG_GENERIC_FIND_NEXT_BIT=y
-CONFIG_GENERIC_GPIO=y
-CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
-CONFIG_HAS_DMA=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT=y
-CONFIG_HAVE_ARCH_KGDB=y
-# CONFIG_HAVE_ARCH_TRACEHOOK is not set
-# CONFIG_HAVE_CLK is not set
-# CONFIG_HAVE_DMA_ATTRS is not set
-# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
-# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
-CONFIG_HAVE_IDE=y
-# CONFIG_HAVE_IOREMAP_PROT is not set
-# CONFIG_HAVE_KPROBES is not set
-# CONFIG_HAVE_KRETPROBES is not set
-CONFIG_HAVE_OPROFILE=y
-CONFIG_HW_RANDOM=y
-# CONFIG_I2C is not set
-# CONFIG_IDE is not set
-CONFIG_INITRAMFS_SOURCE=""
-CONFIG_IRQ_CPU=y
-# CONFIG_ISDN is not set
-CONFIG_KALLSYMS=y
-CONFIG_LEDS_GPIO=y
-# CONFIG_LEMOTE_FULONG is not set
-# CONFIG_MACH_ALCHEMY is not set
-# CONFIG_MACH_DECSTATION is not set
-# CONFIG_MACH_JAZZ is not set
-# CONFIG_MACH_TX39XX is not set
-# CONFIG_MACH_TX49XX is not set
-# CONFIG_MACH_VR41XX is not set
-# CONFIG_MIKROTIK_RB532 is not set
-# CONFIG_MIPS_COBALT is not set
-CONFIG_MIPS_L1_CACHE_SHIFT=5
-# CONFIG_MIPS_MACHINE is not set
-# CONFIG_MIPS_MALTA is not set
-CONFIG_MIPS_MT_DISABLED=y
-# CONFIG_MIPS_MT_SMP is not set
-# CONFIG_MIPS_MT_SMTC is not set
-# CONFIG_MIPS_SIM is not set
-CONFIG_MIPS=y
-CONFIG_MTD_AR7_PARTS=y
-CONFIG_MTD_CFI_STAA=y
-CONFIG_MTD_PHYSMAP_BANKWIDTH=2
-CONFIG_MTD_PHYSMAP_LEN=0
-CONFIG_MTD_PHYSMAP_START=0x10000000
-CONFIG_MTD_PHYSMAP=y
-CONFIG_NO_EXCEPT_FILL=y
-# CONFIG_NO_IOPORT is not set
-CONFIG_PAGEFLAGS_EXTENDED=y
-# CONFIG_PCSPKR_PLATFORM is not set
-CONFIG_PHYLIB=y
-# CONFIG_PMC_MSP is not set
-# CONFIG_PMC_YOSEMITE is not set
-# CONFIG_PNX8550_JBS is not set
-# CONFIG_PNX8550_STB810 is not set
-# CONFIG_PROBE_INITRD_HEADER is not set
-CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
-# CONFIG_SCSI_DMA is not set
-# CONFIG_SERIAL_8250_EXTENDED is not set
-# CONFIG_SGI_IP22 is not set
-# CONFIG_SGI_IP27 is not set
-# CONFIG_SGI_IP28 is not set
-# CONFIG_SGI_IP32 is not set
-# CONFIG_SIBYTE_BIGSUR is not set
-# CONFIG_SIBYTE_CARMEL is not set
-# CONFIG_SIBYTE_CRHINE is not set
-# CONFIG_SIBYTE_CRHONE is not set
-# CONFIG_SIBYTE_LITTLESUR is not set
-# CONFIG_SIBYTE_RHONE is not set
-# CONFIG_SIBYTE_SENTOSA is not set
-# CONFIG_SIBYTE_SWARM is not set
-CONFIG_SWAP_IO_SPACE=y
-CONFIG_SYS_HAS_CPU_MIPS32_R1=y
-CONFIG_SYS_HAS_EARLY_PRINTK=y
-CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
-CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
-CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y
-CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y
-CONFIG_TICK_ONESHOT=y
-CONFIG_TRAD_SIGNALS=y
-# CONFIG_VGASTATE is not set
-CONFIG_VLYNQ=y
-CONFIG_ZONE_DMA_FLAG=0
+++ /dev/null
---- a/arch/mips/Kconfig
-+++ b/arch/mips/Kconfig
-@@ -19,6 +19,24 @@ choice
- prompt "System type"
- default SGI_IP22
-
-+config AR7
-+ bool "Texas Instruments AR7"
-+ select BOOT_ELF32
-+ select DMA_NONCOHERENT
-+ select CEVT_R4K
-+ select CSRC_R4K
-+ select IRQ_CPU
-+ select NO_EXCEPT_FILL
-+ select SWAP_IO_SPACE
-+ select SYS_HAS_CPU_MIPS32_R1
-+ select SYS_HAS_EARLY_PRINTK
-+ select SYS_SUPPORTS_32BIT_KERNEL
-+ select SYS_SUPPORTS_KGDB
-+ select SYS_SUPPORTS_LITTLE_ENDIAN
-+ select SYS_SUPPORTS_BIG_ENDIAN
-+ select GENERIC_GPIO
-+ select GENERIC_HARDIRQS_NO__DO_IRQ
-+
- config MACH_ALCHEMY
- bool "Alchemy processor based machines"
-
---- a/arch/mips/kernel/traps.c
-+++ b/arch/mips/kernel/traps.c
-@@ -1203,9 +1203,22 @@ void *set_except_vector(int n, void *add
-
- exception_handlers[n] = handler;
- if (n == 0 && cpu_has_divec) {
-- *(u32 *)(ebase + 0x200) = 0x08000000 |
-- (0x03ffffff & (handler >> 2));
-- local_flush_icache_range(ebase + 0x200, ebase + 0x204);
-+ if ((handler ^ (ebase + 4)) & 0xfc000000) {
-+ /* lui k0, 0x0000 */
-+ *(u32 *)(ebase + 0x200) = 0x3c1a0000 | (handler >> 16);
-+ /* ori k0, 0x0000 */
-+ *(u32 *)(ebase + 0x204) =
-+ 0x375a0000 | (handler & 0xffff);
-+ /* jr k0 */
-+ *(u32 *)(ebase + 0x208) = 0x03400008;
-+ /* nop */
-+ *(u32 *)(ebase + 0x20C) = 0x00000000;
-+ flush_icache_range(ebase + 0x200, ebase + 0x210);
-+ } else {
-+ *(u32 *)(ebase + 0x200) =
-+ 0x08000000 | (0x03ffffff & (handler >> 2));
-+ flush_icache_range(ebase + 0x200, ebase + 0x204);
-+ }
- }
- return (void *)old_handler;
- }
---- a/arch/mips/Makefile
-+++ b/arch/mips/Makefile
-@@ -167,6 +167,13 @@ libs-$(CONFIG_SIBYTE_CFE) += arch/mips/s
- #
-
- #
-+# Texas Instruments AR7
-+#
-+core-$(CONFIG_AR7) += arch/mips/ar7/
-+cflags-$(CONFIG_AR7) += -Iinclude/asm-mips/ar7
-+load-$(CONFIG_AR7) += 0xffffffff94100000
-+
-+#
- # Acer PICA 61, Mips Magnum 4000 and Olivetti M700.
- #
- core-$(CONFIG_MACH_JAZZ) += arch/mips/jazz/
---- a/include/asm-mips/page.h
-+++ b/include/asm-mips/page.h
-@@ -182,8 +182,10 @@ typedef struct { unsigned long pgprot; }
- #define VM_DATA_DEFAULT_FLAGS (VM_READ | VM_WRITE | VM_EXEC | \
- VM_MAYREAD | VM_MAYWRITE | VM_MAYEXEC)
-
--#define UNCAC_ADDR(addr) ((addr) - PAGE_OFFSET + UNCAC_BASE)
--#define CAC_ADDR(addr) ((addr) - UNCAC_BASE + PAGE_OFFSET)
-+#define UNCAC_ADDR(addr) ((addr) - PAGE_OFFSET + UNCAC_BASE + \
-+ PHYS_OFFSET)
-+#define CAC_ADDR(addr) ((addr) - UNCAC_BASE + PAGE_OFFSET - \
-+ PHYS_OFFSET)
-
- #include <asm-generic/memory_model.h>
- #include <asm-generic/page.h>
+++ /dev/null
---- a/drivers/mtd/Kconfig
-+++ b/drivers/mtd/Kconfig
-@@ -188,6 +188,12 @@ config MTD_MYLOADER_PARTS
- You will still need the parsing functions to be called by the driver
- for your particular device. It won't happen automatically.
-
-+config MTD_AR7_PARTS
-+ tristate "TI AR7 partitioning support"
-+ depends on MTD_PARTITIONS
-+ ---help---
-+ TI AR7 partitioning support
-+
- comment "User Modules And Translation Layers"
-
- config MTD_CHAR
---- a/drivers/mtd/maps/physmap.c
-+++ b/drivers/mtd/maps/physmap.c
-@@ -85,7 +85,7 @@ static int physmap_flash_remove(struct p
-
- static const char *rom_probe_types[] = { "cfi_probe", "jedec_probe", "map_rom", NULL };
- #ifdef CONFIG_MTD_PARTITIONS
--static const char *part_probe_types[] = { "cmdlinepart", "RedBoot", NULL };
-+static const char *part_probe_types[] = { "cmdlinepart", "RedBoot", "ar7part", NULL };
- #endif
-
- static int physmap_flash_probe(struct platform_device *dev)
+++ /dev/null
---- a/drivers/char/Kconfig
-+++ b/drivers/char/Kconfig
-@@ -968,6 +968,15 @@ config MWAVE
- To compile this driver as a module, choose M here: the
- module will be called mwave.
-
-+config AR7_GPIO
-+ tristate "TI AR7 GPIO Support"
-+ depends on AR7
-+ help
-+ Give userspace access to the GPIO pins on the Texas Instruments AR7
-+ processors.
-+
-+ If compiled as a module, it will be called ar7_gpio.
-+
- config SCx200_GPIO
- tristate "NatSemi SCx200 GPIO Support"
- depends on SCx200
---- a/drivers/char/Makefile
-+++ b/drivers/char/Makefile
-@@ -90,6 +90,7 @@ obj-$(CONFIG_HW_RANDOM) += hw_random/
- obj-$(CONFIG_PPDEV) += ppdev.o
- obj-$(CONFIG_NWBUTTON) += nwbutton.o
- obj-$(CONFIG_NWFLASH) += nwflash.o
-+obj-$(CONFIG_AR7_GPIO) += ar7_gpio.o
- obj-$(CONFIG_SCx200_GPIO) += scx200_gpio.o
- obj-$(CONFIG_PC8736x_GPIO) += pc8736x_gpio.o
- obj-$(CONFIG_NSC_GPIO) += nsc_gpio.o
+++ /dev/null
---- a/drivers/Kconfig
-+++ b/drivers/Kconfig
-@@ -100,5 +100,7 @@ source "drivers/auxdisplay/Kconfig"
-
- source "drivers/uio/Kconfig"
-
-+source "drivers/vlynq/Kconfig"
-+
- source "drivers/xen/Kconfig"
- endmenu
---- a/drivers/Makefile
-+++ b/drivers/Makefile
-@@ -96,6 +96,7 @@ obj-$(CONFIG_DCA) += dca/
- obj-$(CONFIG_HID) += hid/
- obj-$(CONFIG_PPC_PS3) += ps3/
- obj-$(CONFIG_OF) += of/
-+obj-$(CONFIG_VLYNQ) += vlynq/
- obj-$(CONFIG_SSB) += ssb/
- obj-$(CONFIG_VIRTIO) += virtio/
- obj-$(CONFIG_REGULATOR) += regulator/
+++ /dev/null
---- a/drivers/watchdog/ar7_wdt.c 2009-01-25 01:17:01.000000000 +1300
-+++ b/drivers/watchdog/ar7_wdt.c 2009-01-25 01:19:15.000000000 +1300
-@@ -293,12 +293,26 @@
- .fops = &ar7_wdt_fops,
- };
-
-+#define AR7_WDT_HARDWARE_ENABLE 0x10
-+
- static int __init ar7_wdt_init(void)
- {
- int rc;
-+ u32 *bootcr;
-+ u32 bootcr_value;
-
- ar7_wdt_get_regs();
-
-+ /* arch/mips/ar7/clocks.c is the only other thing that reads this */
-+ bootcr = (u32 *)ioremap_nocache(AR7_REGS_DCL, 4);
-+ bootcr_value = *bootcr;
-+ iounmap(bootcr);
-+
-+ if (!(bootcr_value & AR7_WDT_HARDWARE_ENABLE)) {
-+ printk(KERN_INFO DRVNAME ": watchdog disabled in hardware (bootcr=%#x)\n", bootcr_value);
-+ return -ENODEV;
-+ }
-+
- if (!request_mem_region(ar7_regs_wdt, sizeof(struct ar7_wdt),
- LONGNAME)) {
- printk(KERN_WARNING DRVNAME ": watchdog I/O region busy\n");
+++ /dev/null
---- a/drivers/net/Kconfig
-+++ b/drivers/net/Kconfig
-@@ -1823,7 +1823,7 @@ config SC92031
-
- config CPMAC
- tristate "TI AR7 CPMAC Ethernet support (EXPERIMENTAL)"
-- depends on NET_ETHERNET && EXPERIMENTAL && AR7 && BROKEN
-+ depends on NET_ETHERNET && EXPERIMENTAL && AR7
- select PHYLIB
- help
- TI AR7 CPMAC Ethernet support
+++ /dev/null
---- a/arch/mips/ar7/platform.c
-+++ b/arch/mips/ar7/platform.c
-@@ -33,6 +33,8 @@
- #include <linux/vlynq.h>
- #include <linux/leds.h>
- #include <linux/string.h>
-+#include <linux/phy.h>
-+#include <linux/phy_fixed.h>
-
- #include <asm/addrspace.h>
- #include <asm/ar7/ar7.h>
-@@ -205,6 +207,13 @@
- .width = 2,
- };
-
-+/* lets assume this is suitable for both high and low cpmacs links */
-+static struct fixed_phy_status fixed_phy_status __initdata = {
-+ .link = 1,
-+ .speed = 100,
-+ .duplex = 1,
-+};
-+
- static struct plat_cpmac_data cpmac_low_data = {
- .reset_bit = 17,
- .power_bit = 20,
-@@ -506,6 +515,10 @@
- }
-
- if (ar7_has_high_cpmac()) {
-+ res = fixed_phy_add(PHY_POLL, cpmac_high.id, &fixed_phy_status);
-+ if (res && res != -ENODEV)
-+ return res;
-+
- cpmac_get_mac(1, cpmac_high_data.dev_addr);
- res = platform_device_register(&cpmac_high);
- if (res)
-@@ -514,6 +527,10 @@
- cpmac_low_data.phy_mask = 0xffffffff;
- }
-
-+ res = fixed_phy_add(PHY_POLL, cpmac_low.id, &fixed_phy_status);
-+ if (res && res != -ENODEV)
-+ return res;
-+
- cpmac_get_mac(0, cpmac_low_data.dev_addr);
- res = platform_device_register(&cpmac_low);
- if (res)
+++ /dev/null
---- a/drivers/serial/8250.c
-+++ b/drivers/serial/8250.c
-@@ -264,6 +264,13 @@ static const struct serial8250_config ua
- .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
- .flags = UART_CAP_FIFO,
- },
-+ [PORT_AR7] = {
-+ .name = "TI-AR7",
-+ .fifo_size = 16,
-+ .tx_loadsz = 16,
-+ .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_00,
-+ .flags = UART_CAP_FIFO | UART_CAP_AFE,
-+ },
- };
-
- #if defined (CONFIG_SERIAL_8250_AU1X00)
-@@ -2552,7 +2559,11 @@ static void serial8250_console_putchar(s
- {
- struct uart_8250_port *up = (struct uart_8250_port *)port;
-
-+#ifdef CONFIG_AR7
-+ wait_for_xmitr(up, BOTH_EMPTY);
-+#else
- wait_for_xmitr(up, UART_LSR_THRE);
-+#endif
- serial_out(up, UART_TX, ch);
- }
-
---- a/include/linux/serial_core.h
-+++ b/include/linux/serial_core.h
-@@ -40,7 +40,8 @@
- #define PORT_NS16550A 14
- #define PORT_XSCALE 15
- #define PORT_RM9000 16 /* PMC-Sierra RM9xxx internal UART */
--#define PORT_MAX_8250 16 /* max port ID */
-+#define PORT_AR7 17
-+#define PORT_MAX_8250 17 /* max port ID */
-
- /*
- * ARM specific type numbers. These are not currently guaranteed
+++ /dev/null
-This patch fixes the network driver cpmac.c for compilation with
-configuration option CONFIG_NETDEVICES_MULTIQUEUE.
-
-These compiler warnings are fixed by the patch:
-drivers/net/cpmac.c: In function 'cpmac_end_xmit':
-drivers/net/cpmac.c:630: warning: passing argument 2 of 'netif_subqueue_stopped' makes pointer from integer without a cast
-drivers/net/cpmac.c:641: warning: passing argument 2 of 'netif_subqueue_stopped' makes pointer from integer without a cast
-drivers/net/cpmac.c: In function 'cpmac_probe':
-drivers/net/cpmac.c:1128: warning: unused variable 'i'
-
-During runtime, the unpatched driver raises a fatal runtime exception.
-This is fixed by calling __netif_subqueue_stopped instead
-of netif_subqueue_stopped, too.
-
-Two additional code parts were modified for CONFIG_NETDEVICES_MULTIQUEUE
-because other drivers do it in the same way.
-
- Signed-off-by: Stefan Weil <weil@mail.berlios.de>
-
---- a/drivers/net/cpmac.c
-+++ b/drivers/net/cpmac.c
-@@ -621,13 +621,13 @@ static void cpmac_end_xmit(struct net_de
-
- dev_kfree_skb_irq(desc->skb);
- desc->skb = NULL;
-- if (netif_subqueue_stopped(dev, queue))
-+ if (__netif_subqueue_stopped(dev, queue))
- netif_wake_subqueue(dev, queue);
- } else {
- if (netif_msg_tx_err(priv) && net_ratelimit())
- printk(KERN_WARNING
- "%s: end_xmit: spurious interrupt\n", dev->name);
-- if (netif_subqueue_stopped(dev, queue))
-+ if (__netif_subqueue_stopped(dev, queue))
- netif_wake_subqueue(dev, queue);
- }
- }
-@@ -737,7 +737,6 @@ static void cpmac_clear_tx(struct net_de
-
- static void cpmac_hw_error(struct work_struct *work)
- {
-- int i;
- struct cpmac_priv *priv =
- container_of(work, struct cpmac_priv, reset_work);
-
-@@ -824,7 +823,6 @@ static irqreturn_t cpmac_irq(int irq, vo
-
- static void cpmac_tx_timeout(struct net_device *dev)
- {
-- int i;
- struct cpmac_priv *priv = netdev_priv(dev);
-
- spin_lock(&priv->lock);
-@@ -1103,7 +1101,7 @@ static int external_switch;
-
- static int __devinit cpmac_probe(struct platform_device *pdev)
- {
-- int rc, phy_id, i;
-+ int rc, phy_id;
- char *mdio_bus_id = "0";
- struct resource *mem;
- struct cpmac_priv *priv;
-@@ -1132,6 +1130,7 @@ static int __devinit cpmac_probe(struct
- }
-
- dev = alloc_etherdev_mq(sizeof(*priv), CPMAC_QUEUES);
-+ //~ dev = alloc_etherdev(sizeof(*priv));
-
- if (!dev) {
- printk(KERN_ERR "cpmac: Unable to allocate net_device\n");
+++ /dev/null
-This is a hack to make cpmac work with the external switch on a DG834 v3; it
-should also work on other similar routers. It has not been tested on hardware
-with multiple cpmac devices or with no external switch. It may be safer to
-move external_switch to pdata rather than trying to detect it, and to set
-phy_mask correctly rather than moving the phy search loop.
-
---- a/drivers/net/cpmac.c 2008-11-11 06:18:24.000000000 +1100
-+++ b/drivers/net/cpmac.c 2009-04-11 10:58:58.000000000 +1000
-@@ -1124,8 +1124,8 @@
-
- static int __devinit cpmac_probe(struct platform_device *pdev)
- {
- int rc, phy_id;
-- char *mdio_bus_id = "0";
-+ char mdio_bus_id[BUS_ID_SIZE];
- struct resource *mem;
- struct cpmac_priv *priv;
- struct net_device *dev;
-@@ -1134,22 +1134,23 @@
-
- pdata = pdev->dev.platform_data;
-
-- for (phy_id = 0; phy_id < PHY_MAX_ADDR; phy_id++) {
-- if (!(pdata->phy_mask & (1 << phy_id)))
-- continue;
-- if (!cpmac_mii.phy_map[phy_id])
-- continue;
-- break;
-+ if (external_switch || dumb_switch) {
-+ strncpy(mdio_bus_id, "0", BUS_ID_SIZE); /* fixed phys bus */
-+ phy_id = pdev->id;
-+ } else {
-+ for (phy_id = 0; phy_id < PHY_MAX_ADDR; phy_id++) {
-+ if (!(pdata->phy_mask & (1 << phy_id)))
-+ continue;
-+ if (!cpmac_mii.phy_map[phy_id])
-+ continue;
-+ strncpy(mdio_bus_id, cpmac_mii.id, BUS_ID_SIZE);
-+ break;
-+ }
- }
-
- if (phy_id == PHY_MAX_ADDR) {
-- if (external_switch || dumb_switch) {
-- mdio_bus_id = 0; /* fixed phys bus */
-- phy_id = pdev->id;
-- } else {
-- dev_err(&pdev->dev, "no PHY present\n");
-- return -ENODEV;
-- }
-+ dev_err(&pdev->dev, "no PHY present\n");
-+ return -ENODEV;
- }
-
- #ifdef CONFIG_NETDEVICES_MULTIQUEUE
-@@ -1189,9 +1190,11 @@
- priv->ring_size = 64;
- priv->msg_enable = netif_msg_init(debug_level, 0xff);
- memcpy(dev->dev_addr, pdata->dev_addr, sizeof(dev->dev_addr));
-+
-+ snprintf(priv->phy_name, BUS_ID_SIZE, PHY_ID_FMT, mdio_bus_id, phy_id);
-
-- priv->phy = phy_connect(dev, cpmac_mii.phy_map[phy_id]->dev.bus_id,
-- &cpmac_adjust_link, 0, PHY_INTERFACE_MODE_MII);
-+ priv->phy = phy_connect(dev, priv->phy_name, &cpmac_adjust_link, 0,
-+ PHY_INTERFACE_MODE_MII);
- if (IS_ERR(priv->phy)) {
- if (netif_msg_drv(priv))
- printk(KERN_ERR "%s: Could not attach to PHY\n",
-@@ -1250,11 +1253,11 @@
-
- cpmac_mii.reset(&cpmac_mii);
-
-- for (i = 0; i < 300000; i++)
-+ for (i = 0; i < 300; i++)
- if ((mask = cpmac_read(cpmac_mii.priv, CPMAC_MDIO_ALIVE)))
- break;
- else
-- cpu_relax();
-+ msleep(10);
-
- mask &= 0x7fffffff;
- if (mask & (mask - 1)) {
-@@ -1267,7 +1270,7 @@
- }
-
- cpmac_mii.phy_mask = ~(mask | 0x80000000);
-- snprintf(cpmac_mii.id, MII_BUS_ID_SIZE, "0");
-+ snprintf(cpmac_mii.id, MII_BUS_ID_SIZE, "1");
-
- res = mdiobus_register(&cpmac_mii);
- if (res)
projects / openwrt.git / commitdiff